Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “confidence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Dayglow emissions of the O2 Herzberg bands and the Rayleigh backscattered spectrum of the earth

It is pointed out that numerous fluorescent emissions from the Herzberg bands of molecular oxygen lie in the spectral region 242-300 nm. This coincides with the wavelength range used by orbiting spectrometers that observe the Rayleigh backscattered spectrum of the earth for the purpose of monitoring the vertical distribution of stratospheric ozone. Model calculations suggest that Herzberg band emissions in the dayglow could provide significant contamination of the ozone measurements if the quenching rate of O2(A3Sigma) is sufficiently small. It is noted that this is especially true near 255 nm, where the most intense fluorescent emissions relative to the Rayleigh scattered signal are located and where past satellite measurements have shown a persistent excess radiance above that expected for a pure ozone absorbing and molecular scattering atmosphere. Very small quenching rates, however, are adequate to reduce the dayglow emission to negligible levels. Noting that available laboratory data have not definitely established the quenching on the rate of O2(A3Sigma) as a function of vibration level, it is emphasized that such information is required before the Herzberg band contributions can be evaluated with confidence.

Frederick, J. E.↗

OH fluorescence in comets - Fluorescence efficiency of the ultraviolet bands

The present investigation is concerned with the calculation of the fluorescence efficiency of OH over a wide range of heliocentric radial velocities. Three vibrational states in each of the two lowest electronic states are included in these calculations, producing a total of nine vibrational bands in the ultraviolet. The attempt is made to reproduce observed, ultraviolet, cometary spectra of OH by utilizing the Swings fluorescence mechanism. The inclusion of four rotational states within each of the three vibrational states and a detailed solar atlas make it possible to match observations very well, although there remain some discrepancies. This ability to reproduce observations provides confidence that the more general results obtained for the fluorescence efficiency as a function of heliocentric radial velocity can be used in interpreting both previous and future observations of OH in comets.

Schleicher, D. G.↗

Methane and nonmethane hydrocarbon concentrations in the North and South Atlantic marine boundary layer

Methane and nonmethane hydrocarbon (NMHC) data were collected in the Atlantic marine boundary layer from 40 N to 32 S latitude during October and November 1980. Average volume mixing ratios for CH4 of 1.69 + or - 0.02 ppmv were obtained north of the intertropical convergence zone (ITCZ) and 1.60 + or - 0.02 ppmv south of the ITCZ. The hemispheric CH4 gradient was very sharp, decreasing rapidly between 14 N and 10 N latitude. Gaseous NMHC concentrations (based on response as CH4) were measured simultaneously and found to lie consistently within the standard error for the individual measurements + or - 0.02 ppmv) after correction for water vapor interference. The correction for water vapor response was large, frequently as much as 80% of the raw NMHC signal. Application of the student's t distribution test to the NMHC data set established that the mean northern and southern hemispheric NMHC mixing ratios measured, 0.016 and 0.010 ppmv, respectively, were statistically different at the 95% confidence level. These results indicate volatile NMHC mixing ratios average less than 0.02 ppmv over the Atlantic and represent the first set of semicontinuous NMHC measurements spanning the North and South Atlantic marine boundary layer.

Cofer, W. R., III↗

Estimation of irrigated land using Landsat digital data

Techniques developed by the University of California and NASA for the utilization of multitemporal Landsat digital data in estimating and mapping irrigated land are presented. Three dates of Landsat were registered to each other and to a USGS 7.5 minute quadrangle map base for approximately 1.9 million acres of land. Other data registered include county boundaries, land use stratification, and digitized ground data. To identify irrigated land, an indicator was used which consisted of the ratio of MSS Band 7 to MSS Band 5 (the 7/5 ratio). A threshold 7/5 irrigated land value was determined for each date, as actively growing land generally has a higher 7/5 ratio than other cover classes. An estimate of irrigated land was determined by Landsat classification with ground data, at a relative standard error of + or - 7.98% at the 95% confidence interval. Mapping evaluation reveals a 94% accuracy, a 7.4% omission rate, and a 6.3% commission rate. In addition, a sample unit size evaluation recommends a 1-1 1/2 square mile sample range.

Brown, C. E.↗

Landsat-based estimation of California's irrigated land

The procedure developed uses two-phase sampling, stratification and multidate Landsat imagery to produce the estimate. Maximizing the advantages of both spectral data and field patterns available from Landsat, three dates of Landsat imagery are interpreted to provide county-wide estimates of the proportion of land irrigated. Ground data, collected on a subset of the area interpreted on Landsat, are used to calibrate the satellite estimate. The satellite and ground measurements are reduced to proportion data and linked using a regression estimator to produce the estimate of irrigated land. It is estimated that 3.99 million hectares were irrigated with a relative standard error of + or - 1.18% at the 99% confidence level. Acreage tabulations provided by the Department of Water Resources show that the Landsat-based estimate differed by less than 0.4% at the state level.

Wall, S. L.↗

SLAM examination of solar cells and solar cell welds

The scanning laser acoustic microscope (SLAM) has been evaluated for non-destructive examination of solar cells and interconnector bonds. Using this technique, it is possible to view through materials in order to reveal regions of discontinuity such as microcracks and voids. Of particular interest is the ability to evaluate, in a unique manner, the bonds produced by parallel gap welding. It is possible to not only determine the area and geometry of the bond between the tab and cell, but also to reveal any microcracks incurred during the welding. By correlating the SLAM results with conventional techniques of weld evaluation a more confident weld parameter optimization can be obtained.

Stella, P. M.↗

Aspects of clear air turbulence severity forecasting and detection

Factors influencing the accuracy of the forecasts of incidences of clear air turbulence (CAT) are discussed, along with techniques for improved verification. Descriptive ranking terms for the intensity of CAT events, ranging from light to extreme, are developed, and meteorological parameters used for predictions are reviewed, including jetstream core location, vertical and horizontal wind shears, stable layers, tropopause height, trough speed, 500-mb vorticity, surface fronts, pressure centers and cyclogenesis, and wind speeds near mountain ridges. Methods of remote detection of CAT, particularly by using radiometry sensitive to the IR water vapor band, are noted to have had some success in detecting actual CAT events and decreasing false alarms. Statistical aspects of CAT encounter severity are discussed, including the establishment of confidence intervals for thresholds of detection of CATs of varying intensities.

Ehernberger, L. J.↗

SCM Handbooks for dc-to-dc Converters

Two documents aid in design of control modules for dc-to-dc converters. Features of SCM include: Adaptive stability, power component stress limiting, implementation of various control laws, unified design approach. Analysis and quidelines contained in handbooks enable engineer to design SCM circuit and confidently predict resulting overall performance.

Lee, F.↗

Equations for Automotive-Transmission Performance

Curve-fitting procedure ensures high confidence levels. Threedimensional plot represents performance of small automatic transmission coasting in second gear. In equation for plot, PL power loss, S speed and T torque. Equations applicable to manual and automatic transmissions over wide range of speed, torque, and efficiency.

Chazanoff, S.↗

Durability of aircraft composite materials

Confidence in the long term durability of advanced composites is developed through a series of flight service programs. Service experience is obtained by installing secondary and primary composite components on commercial and military transport aircraft and helicopters. Included are spoilers, rudders, elevators, ailerons, fairings and wing boxes on transport aircraft and doors, fairings, tail rotors, vertical fins, and horizontal stabilizers on helicopters. Materials included in the evaluation are boron/epoxy, Kevlar/epoxy, graphite/epoxy and boron/aluminum. Inspection, maintenance, and repair results for the components in service are reported. The effects of long term exposure to laboratory, flight, and outdoor environmental conditions are reported for various composite materials. Included are effects of moisture absorption, ultraviolet radiation, and aircraft fuels and fluids.

H. Benson Dextern↗

Adaptive control in the presence of unmodeled dynamics

Stability and robustness properties of a wide class of adaptive control algorithms in the presence of unmodeled dynamics and output disturbances were investigated. The class of adaptive algorithms considered are those commonly referred to as model reference adaptive control algorithms, self-tuning controllers, and dead beat adaptive controllers, developed for both continuous-time systems and discrete-time systems. A unified analytical approach was developed to examine the class of existing adaptive algorithms. It was discovered that all existing algorithms contain an infinite gain operator in the dynamic system that defines command reference errors and parameter errors; it is argued that such an infinite gain operator appears to be generic to all adaptive algorithms, whether they exhibit explicit or implicit parameter identification. It is concluded that none of the adaptive algorithms considered can be used with confidence in a practical control system design, because instability will set in with a high probability.

Rohrs, C. E.↗

Preliminary test results of electrical charged particle generator for application to fog dispersal

A charged particle generator for use in fog dispersal applications was built and preliminary tests were carried out. The parameter used as a measure of performance was the current measured with a needle probe positioned in the charged jet connected to ground through an ammeter. The needle was movable and allowed the current profile throughout the jet to be determined. The measured current is referred to as the current output. The major independent parameters were liquid water injection rate, plenum pressure, and corona voltage. Optimum current output was achieved at the approximate pressure of 30 psig, corona voltage of 5600 volts, and liquid water injection rate of 6 cc/min. The results of the test with the prototype charged particle generator clearly demonstrate that a current on the order of 20 microamperes can be routinely achieved with the system. This measurement of current does not necessarily represent the total issuing from the nozzle current which is expected to be larger. From these results, confidence was established that a charged particle generator which will operate continuously and consistently can be designed, constructed, and operated. Further work is required, however, to better understand the physical mechanisms involved and to optimize the system for fog dispersal application.

Frost, W.↗

Ames Research Center life sciences payload

In response to a recognized need for an in-flight animal housing facility to support Spacelab life sciences investigators, a rack and system compatible Research Animal Holding Facility (RAHF) has been developed. A series of ground tests is planned to insure its satisfactory performance under certain simulated conditions of flight exposure and use. However, even under the best conditions of simulation, confidence gained in ground testing will not approach that resulting from actual spaceflight operation. The Spacelab Mission 3 provides an opportunity to perform an inflight Verification Test (VT) of the RAHF. Lessons learned from the RAHF-VT and baseline performance data will be invaluable in preparation for subsequent dedicated life sciences missions.

Callahan, P. X.↗

Determination of ball bearing dynamic stiffness

The dynamic radial stiffness characteristics of rolling element bearings are currently determined by analytical methods that have not been experimentally verified. These bearing data are vital to rotating machinery design integrity because accurate critical speeds and rotor stability predictions are highly dependent on the bearing stiffness. A tester was designed capable of controlling the bearing axial preload, speed, and rotor unbalance. The rotor and support structures were constructed to permit critical speeds that are predominantly determined by a 57 mm test bearing. A curve of calculated critical speed versus stiffness was used to determine the actual bearing stiffness from the empirical data. The results of extensive testing are used to verify analytical predictions, increase confidence in existing bearing computer programs, and to serve as a data base for efforts to correct these programs.

Beatty, R. F.↗

The computation of Laplacian smoothing splines with examples

Laplacian smoothing splines (LSS) are presented as generalizations of graduation, cubic and thin plate splines. The method of generalized cross validation (GCV) to choose the smoothing parameter is described. The GCV is used in the algorithm for the computation of LSS's. An outline of a computer program which implements this algorithm is presented along with a description of the use of the program. Examples in one, two and three dimensions demonstrate how to obtain estimates of function values with confidence intervals and estimates of first and second derivatives. Probability plots are used as a diagnostic tool to check for model inadequacy.

Wendelberger, J. G.↗

A study of the United States coal resources

Geologically significant coal resources were identified. Statistically controlled tonnage estimates for each resource type were prepared. Particular emphasis was placed on the identification and description of coals in terms of seam thickness, inclination, depth of cover, discontinuities caused by faulting and igneous intrusion, and occurrence as isolated or multiseam deposits. The national resource was organized into six major coal provinces: the Appalachian Plateau, the Interior Basins, the Gulf Coastal Plain, the Rocky Mountain Basins, the High Plains, and North Alaska. Each basin within a province was blocked into subareas of homogeneous coal thickness. Total coal tonnage for a subarea was estimated from an analysis of the cumulative coal thickness derived from borehole or surface section records and subsequently categorized in terms of seam thickness, dip, overburden, multiseam proportions, coal quality, and tonnage impacted by severe faulting and igneous intrusions. Confidence intervals were calculated for both subarea and basin tonnage estimates.

Ferm, J. C.↗

Computation of the intervals of uncertainties about the parameters found for identification

A modeling method to calculate the intervals of uncertainty for parameters found by identification is described. The region of confidence and the general approach to the calculation of these intervals are discussed. The general subprograms for determination of dimensions are described. They provide the organizational charts for the subprograms, the tests carried out and the listings of the different subprograms.

Mereau, P.↗

Irrigated lands assessment for water management: Technique test

A procedure for estimating irrigated land using full frame LANDSAT imagery was demonstrated. Relatively inexpensive interpretation of multidate LANDSAT photographic enlargements was used to produce a map of irrigated land in California. The LANDSAT and ground maps were then linked by regression equations to enable precise estimation of irrigated land area by county, basin, and statewide. Land irrigated at least once in California in 1979 was estimated to be 9.86 million acres, with an expected error of less than 1.75% at the 99% level of confidence. To achieve the same level of error with a ground-only sample would have required 3 to 5 times as many ground sample units statewide. A procedure for relatively inexpensive computer classification of LANDSAT digital data to irrigated land categories was also developed. This procedure is based on ratios of MSS band 7 and 5, and gave good results for several counties in the Central Valley.

Wall, S. L.↗