Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compositional analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Functionalized Polymer Thin Films for Plutonium Capture and Isotopic Screening from Aqueous Sources

The rapid screening of plutonium from aqueous sources remains a critical challenge for nuclear nonproliferation efforts. The determination of trace-level Pu isotopes in water requires offsite sample preparation and analysis; therefore, new methods that combine plutonium purification, concentration, and isotopic screening in a fieldable detection system will provide an invaluable tool for nuclear safeguards. This contribution describes the development and characterization of thin polymer-ligand films for the isolation and concentration of waterborne Pu for direct spectroscopic analyses. Submicron thin films were prepared through spin coating onto Si wafers and consisted of combinations of polystyrene (PS) with dibenzoylmethane, thenoyltrifluoroacetone, and di(2-ethylhexyl)phosphoric acid (HDEHP). Pu uptake studies from solutions at pH from 2.3 to 6.3 indicated that only films containing HDEHP exhibited significant recovery of Pu. High alpha spectroscopy peak energy resolutions were achieved for PS-HDEHP films over a range of film thicknesses from 30 to 250 nm. Furthermore, a separate study was performed to evaluate uptake from a primarily Pu(V) solution where it was observed that doubling the HDEHP loading in the film increased uptake of Pu by an order of magnitude. X-ray photoelectron spectroscopy (XPS) analysis revealed that HDEHP was highly concentrated within the first few nanometers of the film at the higher loading. XPS analysis also revealed that, in the presence of water, HDEHP was stripped from the surface layer of the film at circumneutral pH. While significant losses of ligand were seen in all samples, higher loadings of HDEHP resulted in measurable amounts of ligand retained after a 12-h soak in water. Findings of this study are being used to guide the development of thin-film composite membrane-based detection methods for the rapid, fieldable analysis of Pu in water.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Pseudoelastic deformation in Mo-based refractory multi-principal element alloys

Phase diagrams supported by density functional theory methods can be crucial for designing high-entropy alloys that are subset of multi-principal-element alloys. We present phase and property analysis of quinary (MoW) x Zr y (TaTi) 1-x-y refractory high-entropy alloys from combined Calculation of Phase Diagram (CALPHAD) and density-functional theory results, supplemented by molecular dynamics simulations. Both CALPHAD and density-functional theory analysis of phase stability indicates a Mo-W-rich region of this quinary has a stable single-phase body-centered-cubic structure. We report first quinary composition from Mo-W-Ta-Ti-Zr family of alloy with pseudo-elastic behavior, i.e., hysteresis in stress-strain. Our analysis shows that only Mo-W-rich compositions of Mo-W-Ta-Ti-Zr, i.e., Mo+W, show reproducible hysteresis in stress-strain responsible for pseudo-elastic behavior. The (MoW) 85 Zr 7.5 (TaTi) 7.5 was down-selected based on temperature-dependent phase diagram analysis and molecular dynamics simulations predicted elastic behavior that reveals twinning-assisted pseudoelastic behavior. While mostly unexplored in body-centered-cubic crystals, twinning is a fundamental deformation mechanism that competes against dislocation slip in crystalline solids. Furthermore, this alloy shows identical cyclic deformation characteristics during uniaxial < 100 > loading, i.e., the pseudoelasticity is isotropic in loading direction. Additionally, a temperature increase from 77 to 1,500 K enhances the elastic strain recovery in load-unload cycles, offering possibly control to tune the pseudoelastic behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Size and Time-Resolved Automated Aerosol Sampling Field Campaign Report

To improve the understanding of the impacts of the vertical distribution of aerosol chemical composition on radiative forcing of aerosol, we performed a detailed physicochemical characterization of aerosol particles sampled during ARM deployment of the tethered balloon system at two ARM sites. We used multi-modal microscopy/spectroscopy techniques and advanced mass spectrometry platforms for the analysis of particles. We found variations in size-resolved aerosol composition at different altitudes. We also observed changes in aerosol composition during different seasons. Some of our observations at ARM’s Oliktok Point, Alaska site suggest cloud processing of aerosol while sampling in clouds, below clouds, and above clouds.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

An Advanced Meso-Scale Peridynamic Modeling Technology using High-Performance Computing for Cost-Effective Product Design and Testing of Carbon Fiber Reinforced Polymer Composites in Light-weight Vehicles

We study a peridynamic composite modeling technology based on the discontinuous Galerkin finite element method, implemented in the commercial LS-DYNA software, for modeling and prediction of failure in carbon fiber reinforced polymer composites. The proposed technology is developed for the material failure analysis at the meso-scale, which provides the prevailing fiber-matrix interaction mechanism, without adoption of the representative volume element method and thus avoiding complicated numerical calibration procedures. Three types of experimental tests—in-plane coupon test, out-of-plane coupon test, and a component crash test—are simulated in a high-performance computing environment to assess the performance of the proposed peridynamic composite modeling technology.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Surface-Functionalized Cellulose Nanocrystals as Nanofillers for Crosslinking Processes: Implications for Thermosetting Resins

Understanding the response of fillers in the epoxy resin crosslinking process and characterizing polymer–filler dynamics are the key features that guide the engineering of new thermosetting resin composites. Here, in this work, X-ray photon correlation spectroscopy (XPCS) is used as a thermal analysis tool to track the microscopic changes occurring during the cure of a functionalized cellulose nanocrystal (mCNC)–epoxy composite. In contrast, traditional methods such as differential scanning calorimetry (DSC) and curing rheology are used to understand the kinetics and properties on macroscopic length scales. Of interest is the influence of the mCNC on the curing kinetics and properties of the thermosetting resin. Two levels of modification (increasing hydrophobicity) were chosen to observe the effect of functionalization. Before cure, the highly functionalized CNC (mCNC3) shows a 44% increase in complex viscosity (η*), while the less functionalized CNC (mCNC2) shows a η* value similar to that of the neat resin. As the cure cycle progresses, results from DSC, rheology, and XPCS further show the enhancement in dispersion for mCNC3. The results show a clear difference in the maximum drift velocity, maximum heat flow, and complex viscosity during the ramp to the isothermal cure temperature (T cure ). Such results suggest that mCNC3 contains a well-dispersed network of particles due to the higher level of functionalization. During T cure , a transition in elastic modulus (G') occurs only for the highly functionalized CNC particle system. We believe that heat-induced aggregation occurs, and the crosslinked resin ultimately dominates the macroscopic properties of the final cured system for all samples. The results from the three techniques are in good agreement and showcase XPCS as a beneficial experimental tool for characterizing the microscopic dynamics of particulate-filled thermosetting resins. Hence, we envision this to be a fundamental curing study for the design of thermosetting resin composites.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structural stability of mechanically alloyed amorphous (FeCoNi) 70 Ti 10 B 20 under high-temperature and high-pressure

Nanostructured (FeCoNi) 70 Ti 10 B 20 (at%) alloy was synthesized by mechanical alloying from elemental powder mixture of Fe, Co, Ni, Ti and B using ball milling. The effect of ball milling time on the evolution of structure and morphology was investigated by X-ray diffraction, scanning and transmission electron microscopy and differential thermal analysis. It was observed that the formation of solid solution of (FeCoNi) 70 Ti 10 B 20 started from the very onset of the milling process. Crystallite size and lattice strains seemed to be leveled off after 20 h of milling with no further major changes. The milling process for longer periods introduced severe plastic deformations causing formation of amorphous phase of (FeCoNi) 70 Ti 10 B 20 . The amorphous alloy composition was confirmed by energy dispersive X-ray spectroscopy analysis that showed an excellent homogeneity of the alloying elements. The phase stability of the mechanically alloyed amorphous sample was further verified by employing high-temperature and high-pressure studies. The alloy samples heat-treated at 700 °C revealed crystallization of the amorphous phase. However, synchrotron-based high-pressure ambient temperature X-ray diffraction studies confirmed that the amorphous phase of the alloy remained stable up to the pressure of 30 GPa. Here, the 50 h milled sample after being annealed at 350 °C showed improvement in the soft magnetic properties of the alloy, which was due to the probable elimination of the residual stress in the amorphous phase of the alloy powders.

36 MATERIALS SCIENCE↗
DOE OSTI2021

CO2 Capture Strategies via Mineralization with Industrial Waste Brines

Large coal-fired power plants (>500 MW) account for 30% of global CO2 emissions, and long-term management of this CO2 to is urgently needed mitigate global temperature increases. Sequestration of CO2 within stable mineral carbonates (e.g., CaCO3) represents an attractive emission reduction strategy because it offers a leakage-free alternative to geological storage of CO2 in an environmentally friendly form. We have previously described a mineralization process in which divalent cations are sourced from various waste streams (e.g., produced water and brackish water) and alkalinity is induced via regenerable ion-exchange materials (Bustillos et. al. Frontiers in Energy Research. 2020, 8, 352). In our process, aqueous carbonate-bearing streams with pH > 8 are produced by contacting fresh water and carbon dioxide with various ion-exchange materials (e.g., Na form zeolites or ion exchange resins). These streams are mixed with produced water containing varying concentrations (~0.01 – 1.0 M) of Ca2+ leading to the precipitation of solid calcium carbonate (PCC). This process has the advantages of using regenerable solids in a simple and continuous process to increase the pH of water by ion exchange instead of relying on the consumption of costly and unsustainable sources of alkalinity (e.g., sodium hydroxide). While once-through column experiments showed the above benefits, the same were yet to established in a steady-state process with recycle streams. In this work, we set up a process simulation to quantify the energy requirements and CO2 emissions associated with the process and seek optimal produced water compositions and CO2 concentrations (5 – 20 vol%). The process simulation was set up in ASPEN Plus using eRNTL as the thermodynamic property method and sequential modular strategy. Ion exchange alkaline solution was simulated using sodium hydroxide and validated against the experimental data obtained from once-through kinetic experiments. Nanofiltration and reverse osmosis membrane steps were also implemented for the separation of divalent cations and production of fresh water and a regeneration stream following mineralization. Sensitivity analysis was carried out using a range of produced water compositions (0.01 – 1.0 M Ca2+, 0.001 – 0.15 M Mg2+, 0.5 – 3.5 M Na+ and 0.0004 – 0.002 M Fe2+) according to the United States Geological Survey (USGS) database. Calcium carbonate yields increased with increasing CO2 concentrations and were maximized using produced water compositions with larger Ca2+ concentrations. Maximum calcium carbonate yields produced at 5 vol%, 12 vol% and 20 vol% CO2 were 2.3 mmol/L, 5.5 mmol/L, and 9.3 mmol/L, respectively, with the formation of brucite (a magnesium hydroxide phase, Mg(OH)2) and goethite (an iron hydroxide phase, FeOOH) as the primary contaminant phases (99% calcite, 0.6% brucite, 0.4% goethite), which agree with phases detected by XRD experimentally. These results indicate high purity calcium carbonate can be precipitated using industrial waste streams. Consequentially, energy consumption and net CO2 emissions were minimized where precipitated calcium carbonate was maximized for all produced water compositions and CO2 concentrations. Minimum energy consumptions were 0.21 kWh/ton CO2 processed, with 98% of the energy input required coming from the membrane filtration steps. Produced water compositions with large Na+ concentrations (> 0.5 M) were effective at reducing energy consumptions due to faster regeneration time of ion exchange materials. Additionally, calculated net CO2 emissions were negative for the process and ranged from -0.02 kg/ton CO2 to -0.15 kg/ton CO2 processed, indicating a low emission process. We will also present techno-economic assessment showing the economic benefits of the current process as an alternative to the addition of stoichiometric bases to induce alkalinity for the precipitation of CaCO3.

Simonetti, Dante↗
DOE OSTI2025

Delamination-informed lifecycle decisions: A dielectric and machine learning framework for composite sorting and recycling

Composite materials are widely used in aerospace, marine, and automotive sectors due to their high strength-to-weight ratio and durability. However, their long-term reliability can be compromised by damage accumulation. Specifically, delamination initiation serves as a precursor to structural failure, which is often difficult to detect during damage inspection. Identifying and sorting delamination initiation in samples not only increases operational safety while providing critical information for end-of-life decisions, which influences both the service life extension value and the efficiency of fiber extraction during recycling. This research addresses two challenges: (1) developing a nondestructive, ex-situ framework to sort composite materials based on damage severity, particularly delamination, and (2) understanding how damage in composites influences resin removal during pyrolysis. Both experimental work and finite element analysis were performed to predict critical stress levels that are associated with delamination onset. Based on these results, three loading levels 50 %, 75 %, and 90 % of maximum stress, were selected for controlled experiments, generating composite samples with varying extents of damage for machine learning model training. Microscopic imaging of these samples confirmed the damage progression from matrix cracking to delamination, validating the computational predictions. We explored supervised machine learning using dielectric measurements to classify damage states. Preliminary results show an artificial neural network can identify early delamination which is a potential precursor to failure, with 94.44 % accuracy on our dataset. A parallel investigation into the effect of damage severity on pyrolysis recycling showed that heavily delaminated samples required significantly less energy for comparable matrix removal than undamaged samples.

dielectric variables↗
DOE OSTI2025

High-throughput micro-scale bandgap mapping for perovskite-inspired materials with complex composition space

Abstract To realize the full promise of high-throughput experimental workflows, the rate of sample synthesis must be matched by that of characterization. Of growing interest are contactless optical techniques that can rapidly measure material homogeneity and properties. Here, we present a hyperspectral imaging method to measure local optical bandgap distributions within samples, utilizing spatially-resolved reflectance spectra coupled with automated data analysis. We collect approximately one million optical bandgap data across the compositional space of Cs 3 (Bi x Sb 1-x ) 2 (Br y I 1-y ) 9 perovskite-inspired materials. Our results show non-monotonic bandgap variations (i.e., bandgap bowing) along six composition gradient sequences, in addition to identifying samples with multiple bandgaps in statistics. High-throughput transient absorption spectroscopy reveals that within these compositions, the depletion of the ground state carriers to excited states occurred at discrete energy levels with independent carrier dynamics, consistent with the bandgap observation and indicative of phase separation. This work demonstrates the potential for rapid optical measurements to assess material quality and homogeneity in a high-throughput experimental setting, supporting screening and recipe optimization of optoelectronic material candidates with desired carrier dynamics and optical properties.

Science & Technology - Other Topics↗
DOE OSTI2022

Characterization of anisotropic mechanical properties of polymer composites from a hybrid additive manufacturing-compression molding process using x-ray computer tomography

In this study, anisotropic stiffness tensors were reconstructed based on fiber orientation distributions obtained from X-ray computer tomography (xCT). A preform was manufactured via a big area additive manufacturing (BAAM) system with carbon fiber (CF) filled acrylonitrile butadiene styrene (ABS). The tailored preform from additive manufacturing (AM) was used in the compression molding (CM) process to produce a low-void high-performance thermoplastic composite panel. An xCT technique was employed to detect the fiber orientations in CF/ABS composites manufactured via three different methods: AM from BAAM, extrusion compression molding (ECM), and AM-CM. The anisotropic stiffness tensor was obtained from the composite panel manufactured via the three manufacturing methods (AM, ECM, and AMCM). A micromechanics theory was used to obtain the orthotropic stiffness tensors of the composite panels and compared with the experimental values. The predicted stiffness tensors of AM and AM-CM composite panels were used to study the deformation characteristics of a steering wheel during airbag deployment by performing finite element analysis (FEA). The approach developed in this study can be utilized for evaluating high-performance composites.

Pokkalla, Deepak↗
DOE OSTI2023

Isoplethal study of phase formation and morphology in uranium-304L steel via scanning electron microscopy

Understanding the formation of uranium alloys with steel is important to advance nuclear technologies involving U metal fuels and machining U metal, and for nuclear forensics applications. No known phase diagram for the quaternary U-(M = Fe, Ni, Cr) system exists. For this work, we synthesize samples of U-304 L steel (nominal composition 70.1:18.3:10.4 at% Fe:Cr:Ni) across the U composition range 4.45—63.35 at%U by arc melting under inert conditions. Using the binary UFe phase diagram as a reference, we identify four U-steel alloy phases. We find the known U-Fe analogue phases UM 2 and U 6 M, and two low-U composition phases with nominal compositions UM 10 and U 2 M 7 . We apply a correlation length analysis to backscatter scanning electron microscopy images of sectioned and polished cross sections to quantify the domain formation length scale. We demonstrate that these depend heavily on the initial composition and range from 30 nm to 1.5 µm. This result, in particular, could be applicable to theoretical predictions of transport properties. Furthering our understanding of U alloy phase formation with important structural elements such as steel primaries is foundational in developing future nuclear technology.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Coordination-Dependent Chemical Reactivity of TFSI Anions at a Mg Metal Interface

Charge transfer across the electrode–electrolyte interface is a highly complex and convoluted process involving diverse solvated species with varying structures and compositions. Despite recent advances in in situ and operando interfacial analysis, molecular specific reactivity of solvated species is inaccessible due to a lack of precise control over the interfacial constituents and/or an unclear understanding of their spectroscopic fingerprints. However, such molecular-specific understanding is critical to the rational design of energy-efficient solid–electrolyte interphase layers. We have employed ion soft landing, a versatile and highly controlled method, to prepare well-defined interfaces assembled with selected ions, either as solvated species or as bare ions, with distinguishing molecular precision. Equipped with precise control over interfacial composition, we employed in situ multimodal spectroscopic characterization to unravel the molecular specific reactivity of Mg solvated species comprising (i.e., bis(trifluoromethanesulfonyl)imide, TFSI – ) anions and solvent molecules (i.e., dimethoxyethane, DME/G1) on a Mg metal surface relevant to multivalent Mg batteries. In situ multimodal spectroscopic characterization revealed higher reactivity of the undercoordinated solvated species [Mg-TFSI-G1] + compared to the fully coordinated [Mg-TFSI-(G1) 2 ] + species or even the bare TFSI – . These results were corroborated by the computed reaction pathways and energy barriers for decomposition of the TFSI – within Mg solvated species relative to bare TFSI – . Finally, we evaluated the TFSI reactivity under electrochemical conditions using Mg(TFSI) 2 –DME-based phase-separated electrolytes representing different solvated constituents. Based on our multimodal study, we report a detailed understanding of TFSI – decomposition processes as part of coordinated solvated species at a Mg-metal anode that will aid the rational design of improved sustainable electrochemical energy technologies.

25 ENERGY STORAGE↗
DOE OSTI2024

Self-Buffering system for Cost-Effective production of lactic acid from glucose and xylose using Acid-Tolerant Issatchenkia orientalis

This study presents a cost-effective strategy for producing organic acids from glucose and xylose using the acid- tolerant yeast, Issatchenkia orientalis. I. orientalis was engineered to produce lactic acid from xylose, and the resulting strain, SD108XL, successfully converted sorghum hydrolysates into lactic acid. In order to enable low- pH fermentation, a self-buffering strategy, where the lactic acid generated by the SD108XL strain during fermentation served as a buffer, was developed. As a result, the SD108 strain produced 67 g/L of lactic acid from 73 g/L of glucose and 40 g/L of xylose, simulating a sugar composition of sorghum biomass hydrolysates. Moreover, techno-economic analysis underscored the efficiency of the self-buffering strategy in streamlining the downstream process, thereby reducing production costs. These results demonstrate the potential of I. orientalis as a platform strain for the cost-effective production of organic acids from cellulosic hydrolysates.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Energy-Dispersive X-ray Spectroscopy and Atom-probe Tomography Data Quantifying Component-Ratios of Multicomponent Nano-Precipitates in Ion-Irradiated Ceria

Samples of ~1 µm films of CeO2 doped with 2 wt% Mo, 1.5 wt% Ru, 0.75 wt% Pd, 0.5 wt% Re and 0.25 wt% Rh grown with pulsed laser deposition were irradiated with I2+ ions (610°C and 730°C, 1016 and 5×1016 I2+/cm2). For selected samples post-irradiation heat treatment was conducted (900°C, 1100°C). The specimens were sectioned with focussed ion beam milling and characterized in a transmission electron microscope with energy dispesive x-ray spectroscopy, and with atom-probe tomography. Energy dispersive x-ray spectroscopy was used to obtain elemental maps showing the distribution of dopants in the specimen after exposure. Some of these maps are discussed in detail in our companion article “Formation of multicomponent alloy particles in doped ceria under I2+ ion irradiation and thermal annealing” in the Journal of Nuclear Materials [REF]. Advanced computational analysis could be used to more accurately quantify local compositions. Data is provided for additional regions of interest and one additional irradiation condition. The doped Ceria film that was heat treated at 1100 °C delaminated from the substrate in most places. Samples were extracted from the underside of a delaminated piece and analyzed with atom-probe tomography. The resulting data show Ceria and a Mo-rich particle and demonstrate that this approach is feasable in principle to study local compositions in a sample exposed to such extreme conditions.

multicomponent alloys, epsilon phase, EDS, atom pr↗
DOE OSTI2020

One-step transformation of biomass to fuel precursors using a bi-functional combination of Pd/C and water tolerant Lewis acid

Direct one-pot transformation of lignocellulosic biomass has been developed as an effective and sustainable strategy to produce fuel blend stocks and high value chemical building blocks. In this wok, a bi-functional catalyst system consisting of palladium supported on carbon (Pd/C) and metal triflates (i.e., Sm(OTf) 3 , La(OTf) 3 , and Cu(OTf) 2 ) were shown to promote the biomass liquefaction in both hot-compressed water and supercritical ethanol medium, converting fir wood into oxygenated compounds. We report the highest bio-oil yield from hydrothermal liquefaction (HTL) was 10.47 wt% over Pd/C whereas the highest bio-oil yield of 49.71 wt% was achieved from supercritical ethanol liquefaction (SCEL) over the bi-functional catalyst system of Pd/C and La(OTf) 3 . Higher heating values, carbon recovered values and boiling point distributions were further determined for elucidating the physical properties of the bio-oils. Gas chromatography mass spectrometry (GC–MS) analysis of the bio-oils revealed the chemical composition of the bio-oils. Substituted phenols and cyclopentenone/cyclopentanone type compounds consisted of more than 60 area% of the total products from HTL, whereas phenol and esters represented the major products from SCEL. The major reaction pathways are proposed based on the GC–MS results, which include depolymerizaton, isomerization, dehydration, condensation, and hydrogenation.

09 BIOMASS FUELS↗
DOE OSTI2022

Highly swellable hydrogels prepared from extensively oxidized lignin

Biopolymers such as lignin are gaining renewed appeal due to the need for sustainable materials. Herein, we used chelator-mediated Fenton (CMF) chemistry to oxidize Kraft lignin to develop sustainable super absorbent materials. The CMF chemistry adds oxygen, opens aromatic rings and increases COOH content, producing hydrophilic lignin without depolymerization. UV absorption, molecular weight, elemental analysis, and titration were used to study the chemical compositions of CMF-processed lignin. Then the chemically modified hydrophilic lignin was used to produce lignin-based hydrogels utilizing an aqueous polymerization and cross-linking reaction that enabled tunable properties. The resulting lignin hydrogels absorbed water up to 96% and swelled up to 2400%, as well as being re-swellable in water. These lignin-based hydrogels may be applicable in water-absorbing products in consumer goods and agriculture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Reversible Electron-Beam Patterning of Colloidal Nanoparticles at Fluid Interfaces

The directed self-assembly of colloidal nanoparticles (NPs) using external fields guides the formation of sophisticated hierarchical materials but becomes less effective with decreasing particle size. As an alternative, electron-beam-driven assembly offers a potential avenue for targeted nanoscale manipulation, yet remains poorly controlled due to the variety and complexity of beam interaction mechanisms. Here, we investigate the beam–particle interaction of silica NPs pinned to the fluid–vacuum interface of ionic liquid droplets. In these experiments, scanning electron microscopy of the droplet surface resolves NP trajectories over space and time while simultaneously driving their reorganization. With this platform, we demonstrate the ability to direct particle transport and create transient, reversible colloidal patterns on the droplet surface. By tuning the beam voltage, we achieve precise control over both the strength and sign of the beam–particle interaction, with low voltages repelling particles and high voltages attracting them. This response stems from the formation of well-defined solvent flow fields generated from trace radiolysis of the ionic liquid, as determined through statistical analysis of single-particle trajectories under varying solvent composition. Altogether, electron-beam-guided assembly introduces a versatile strategy for nanoscale colloidal manipulation, offering new possibilities for the design of dynamic, reconfigurable systems with applications in adaptive photonics and catalysis.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Insights into the Enhanced Reversibility of Graphite Anode Upon Fast Charging Through Li Reservoir

Increasing the charging rate and reducing the charging time for Li-ion batteries are crucial to realize the mainstream of electric vehicles. However, it is formidable to avoid the Li plating on graphite anode upon fast charging. Despite the tremendous progress in Li detection techniques, the fundamental mechanism of Li plating and its chemical/electrochemical responses upon cycling still remains elusive. Herein, we present a comprehensive electrochemical method to investigate the fast charging behavior of graphite electrode. A detailed analysis is directed toward understanding the changes in phase, composition, and morphology of the fast-charged graphite. By applying a resting process, we scrutinize the further reactions of the plated Li, which readily transforms into irreversible (dead) Li. We further develop a modified graphite electrode with a thin Ag coating as the Li reservoir. The plated Li can be "absorbed" by the Ag layer to form the Li-Ag solid solution that suppresses the formation of dead Li and provides structural stability, thus promoting the further lithiation of graphite and enhancing the reversibility. Here this work not only provides additional insights into the fast charging behavior of graphite electrode but also demonstrates a potential strategy to improve the fast charging performance of graphite anode.

25 ENERGY STORAGE↗