Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ccs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Pathway To Low-Carbon Lignite Utilization; U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) Cooperative Agreement No. DE-FE0024233

Utilities continue to investigate ways to decrease their carbon footprint. Carbon capture and storage (CCS) can enable existing power generation facilities to maintain operations and address carbon reduction. Subtask 2.1 – Pathway to Low-Carbon Lignite Utilization focused on several research areas in an effort to find ways to decrease the cost of capture across both precombustion and postcombustion platforms. Two postcombustion capture solvents were tested, one from CO 2 Solutions Inc. and one from ARCTECH, Inc. The CO 2 Solutions solvent had been evaluated previously, and the company had incorporated the concept of a rotating packed bed (RPB) to replace the traditional packed columns typically used. In the limited testing performed at the Energy & Environmental Research Center (EERC), no CO 2 reduction benefit was seen from the RPB; however, if the technology could be scaled up, it may introduce some savings in capital expense and overall system footprint. Rudimentary tests were conducted with the ARCTECH solvent to evaluate if it could be utilized in a spray tower configuration contactor and capture CO 2 , SO 2 , and NO x . This solvent after loading can be processed to make an additional product to filter wastewater, providing a second-tier usable product. Modeling of the RPB process for scaling to a 550-MW power system was also conducted. The reduced cost of RPB systems combined with a smaller footprint highlight the potential for reducing the cost of capturing CO 2 ; however, more extensive testing is needed to truly evaluate their potential for use at full scale. Hydrogen separation membranes from Commonwealth Scientific and Industrial Research Organisation (CSIRO) were evaluated through precombustion testing. These had also been previously tested and were improved by CSIRO for this test campaign. They are composed of vanadium alloy, which is less expensive than the palladium alloys that are typically used. Their performance was good, and they may be good candidates for medium-pressure gasifiers, but much more scale-up work is needed. Next-generation power cycles are currently being developed and show promise for high efficiency, and the utilization of supercritical CO 2 to drive a turbine could significantly increase cycle efficiency over traditional steam cycles. The EERC evaluated pressurized oxy-combustion technology from the standpoint of CO 2 purification. If impurities can be removed, the costs for CO 2 capture can be lowered significantly over postcombustion capture systems. Impurity removal consisted of a simple water scrubber referred to as the DeSNO x process. The process worked well, but corrosion management is crucial to its success. A model of this process was constructed. Finally, an integrated gasification combined-cycle (IGCC) system model, developed by the Massachusetts Institute of Technology (MIT), was modified to allow for the modeling of membrane systems in the IGCC process. This modified model was used to provide an assessment of the costs of membrane use at full scale. An economic estimation indicated a 14% reduction in cost for CO 2 separation over the SELEXOL™ process. This subtask was funded through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal sponsors for this project were the North Dakota Industrial Commission, Basin Electric Power Cooperative, and Allete, Inc. (including BNI Coal and Minnesota Power).

24 POWER TRANSMISSION AND DISTRIBUTION↗

Optimizing and Quantifying CO 2 Storage Resource in Saline Formations and Hydrocarbon Reservoirs

In an effort to reduce carbon dioxide (CO 2 ) emissions from large stationary sources, carbon capture and storage (CCS) is being investigated as one approach. This work assesses CO 2 storage resource estimation methods for deep saline formations (DSFs) and hydrocarbon reservoirs undergoing CO 2 enhanced oil recovery (EOR). Project activities were conducted using geologic modeling and simulation to investigate CO 2 storage efficiency. CO 2 storage rates and efficiencies in DSFs classified by interpreted depositional environment were evaluated at the regional scale over a 100-year time frame. A focus was placed on developing results applicable to future widespread commercial-scale CO 2 storage operations in which an array of injection wells may be used to optimize storage in saline formations. The results of this work suggest future investigations of prospective storage resource in closed or semiclosed formations need not have a detailed understanding of the depositional environment of the reservoir to generate meaningful estimates. However, the results of this work also illustrate the relative importance of depositional environment, formation depth, structural geometry, and boundary conditions on the rate of CO 2 storage in these types of systems. CO 2 EOR occupies an important place in the realm of geologic storage of CO 2 , as it is likely to be the primary means of geologic CO 2 storage during the early stages of commercial implementation, given the lack of a national policy and the viability of the current business case. This work estimates CO 2 storage efficiency factors using a unique industry database of CO 2 EOR sites and 18 different reservoir simulation models capturing fluvial clastic and shallow shelf carbonate depositional environments for reservoir depths of 1219 and 2438 meters (4000 and 8000 feet) and 7.6-, 20-, and 64-meter (25-, 66,- and 209-foot) pay zones. The results of this work provide practical information that can be used to quantify CO 2 storage resource estimates in oil reservoirs during CO 2 EOR operations (as opposed to storage following depletion) and the uncertainty associated with those estimates.

54 ENVIRONMENTAL SCIENCES↗

Direct Coal -to-Liquids (CTL) for Jet Fuel Using Biomass-Derived Solvents

Battelle has demonstrated a novel and potentially breakthrough technology for a direct coal-to-liquids (CTL) process for producing jet fuel using biomass-derived coal solvents (bio-solvents). The Battelle process offers a significant reduction in capital and operating costs and a substantial reduction in greenhouse gas (GHG) emissions, without requiring carbon capture and storage (CCS). The results of the project are the advancement of three steps of the hybrid coal/biomass-to-jet fuel process to the technology readiness level (TRL) of 5. The project objectives were achieved over two phases. In Phase 1, all three major process steps were explored and refined at bench-scale, including: (1) biomass conversion to high hydrogen-donor bio-solvent; (2) coal dissolution in biomass-derived bio-solvent, without requiring molecular H 2 , to produce a synthetic crude (syncrude); and (3) two-stage catalytic hydrotreating/hydrogenation of syncrude to jet fuel and other distillates. In Phase 2, all three subsystems of the CTL process were scaled up to a pre-pilot scale, and an economic analysis was carried out. A total of over 40 bio-solvents were identified and prepared. The most unique attribute of Battelle’s bio-solvents is their ability to provide much-needed hydrogen to liquefy coal and thus increase its hydrogen content so much that the resulting syncrude is liquid at room temperature. Based on the laboratory-scale testing with bituminous coals from Ohio and West Virginia, a total of 12 novel bio-solvent met the goal of greater than 80% coal solubility, with 8 bio-solvents being as good as or better than a well-known but expensive hydrogen-donor solvent, tetralin. The Battelle CTL process was then scaled up to 1 ton/day (1TPD) at a pre-pilot facility operated in Morgantown, WV. These tests were conducted, in part, to produce enough material for syncrude-upgrading testing. To convert the Battelle-CTL syncrude into a form suitable as a blending stock for jet turbine fuel, a two-step catalytic upgrading process was developed at laboratory scale and then demonstrated at pre-pilot scale facility in Pittsburg, PA. Several drums of distillate products were produced, which were then distilled into unblended (neat) synthetic jet fuel and diesel products for a detailed characterization. Based on a detailed characterization of the synthetic jet fuel, a 20% synthetic, 80% commercial jet fuel blend was prepared, which met all specifications. An analysis of the synthetic diesel product showed that it has the promise of being a drop-in fuel as super-low (less than 15 ppm)-sulfur diesel fuel. A detailed economic analysis showed that the Battelle liquefaction process is economical at between 1000 metric tons/day (MT/day) and 2000 MT/day. The unit capital cost for Battelle CTL process for making jet fuel is 50K USD/daily bbl compared to 151K USD/daily bbl for indirect CTL, based on 2011 dollars. The jet-fuel selling cost at the refinery, including a 12% capital cost factor (which included profit), for the Battelle CTL process is 61USD/bbl (1.45 USD/gallon). This is competitive with crude oil price of 48 USD/bbl. At the same time, the GHG emissions of 3.56 MT CO 2 /MT fuel were lower than the GHG emissions of 3.79 MT CO 2 /MTfuel for petroleum-based fuels and 7.77 MT CO 2 /MT fuel for indirect CTL. Thus, the use of bio-solvents completely eliminates the need for carbon capture in the case of Battelle CTL process. The superior economics and low GHG emissions for the Battelle CTL process has thus sparked worldwide interest and some potential commercialization opportunities are emerging.

01 COAL, LIGNITE, AND PEAT↗

Final Technical Report of the project "Controlling Quantum Information by Quantum Correlations"

The report describes hypotheses, aims, methods and results of the project 20170675PRD2, “Controlling Quantum Information by Quantum Correlations”, which has been run from July 31, 2017 to January 7, 2018. The technical work has been performed by Director’s Fellow Davide Girolami of the T-4 Division, Physics of Condensed Matter and Complex Systems, under the supervision of Wojciech Zurek (T-4), Lukasz Cincio (T-4), and Marcus Daniels (CCS-7). The project ended as Davide Girolami has been converted to J. R. Oppenheimer Fellow to work on the project 20180702PRD1, “Optimal Control of Quantum Machines”, started on January 8, 2018.

97 MATHEMATICS AND COMPUTING↗

Cyber Protection and Resilience Index: An Indicator of an Organization's Cyber Protection and Resilience Program

In 2014, the U.S. Department of Homeland Security (DHS) and its Cyber Security Advisors (CSAs) began surveying critical infrastructure by using the Cyber Infrastructure Survey Tool (C-IST). The collected information is specific to an organization’s cyber protection and resilience program on a critical cyber service (CCS), which includes management, personnel, controls, incident response, and cyber dependencies.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Assessment of CO 2 Storage Resources in Depleted Oil and Gas Fields in the Ship Shoal Area, Gulf of Mexico

The Gulf of Mexico is one of the most important regions in the United States for energy resources and infrastructure. Gulf of Mexico federal offshore oil and gas production accounts for 17% of total U.S. crude oil production and 5% of total U.S. gas production (EIA Gulf of Mexico Fact Sheet). This region presents an excellent combination of high need and significant opportunity for large scale geologic storage of CO 2 . The Ship Shoal Area is located about 20 miles offshore Louisiana within the Gulf Coast federal waters. Miocene and Pliocene sediments in the Ship Shoal Area are proven to provide excellent and secure traps for oil and gas. The Ship Shoal Area contains a large number of depleted oil and gas fields either currently abandoned, or planned for abandonment by 2025, which may provide very significant potential CO 2 storage capacity. GeoMechanics Technologies conducted a comprehensive research project to better characterize Neogene sediments in the Ship Shoal Area for high volume CO 2 storage. The data generated from literature, well data, well log, and formation evaluation were input into Rockwork 16 geologic software to create a detailed geologic model for the Ship Shoal study area. The geologic grids were then fed into TOUGH2, the gas migration model software and FLAC 3D, the geomechanical model software. The fluid flow modeling for both the Miocene and Pliocene simulation from both Block 107 and Block 84 indicated that Pliocene and Miocene are a good reservoir for the CO 2 sequestration. Thirty years of CO 2 injection (at a rate of 1 million metric tons CO 2 per year) and 30 years of observation simulations were run with the fluid flow modeling. The 3D geomechanical modeling for Ship Shoal Block 107 and Block 84 were developed to evaluate induced surface deformation and potential fault reactivation after 30 years CO 2 injection at base of Pliocene and at upper Miocene injection locations. Evaluation results indicate low to no risks for fault slips or fault reactivation. Twelve well bores and 76 well bores for Ship Shoal Blocks 84 and 107 respectively were reviewed for their cement history. Most wells (57 out of 76 and 7 out of 12 wells in Ship Shoal Block 107 and 84 respectively) have good integrity. Nineteen and 5 wells (in Ship Shoal Block 107 and 84 respectively) with no top plug, incomplete cement or Plug and Abandonment information are given yellow cautionary indicators. These cautionary wells may provide leakage paths of CO 2 through the well bores to the USDWs. Using our Quantitative Risk & Decision Analysis Tool (QRDAT) for caprock integrity evaluation, we compared Ship Shoal’s risk to that of In Salah, Sleipner, Kevin Dome, Loudon, Illinois Industrial CCS and Wilmington Graben. We found the risk at the Ship Shoal Blocks 84 and 107 fields are similar to the known CO 2 active sequestration sites, but lower than the Wilmington Graben turbidities offshore California studied site. The risk of natural seismicity in the Gulf of Mexico is relatively low. Geomechanics Technologies has documented the top 25 CO 2 emission sources within the close proximity of the Ship Shoal Block 84 and 107 fields. All the offshore and onshore pipelines have been digitized and can be viewed in an interactive website (http://www.geomechanicstech.com/shipshoal.html). We also performed a feasibility study on the potential for converting existing oil or gas pipelines for CO 2 transport. There are abandoned, idled and retired onshore and offshore pipelines. However, there is no standard specification for maximum pipeline pressures needed for CO 2 transport. It is a function of design, materials, and testing provided; thus it will be the responsibility of the pipeline operator to correctly determine, maintain and operate within the limits of the pipelines. There are a few transit corridors extending from onshore Louisiana (Cailou Bay) to offshore trunk-lines. The cost for constructing a pipeline has increased about 46% from 2015 to an average cost of $5,064,046 per mile in 2016. We use the NETL CO 2 storage resource mass estimate to calculate the potential resources for Ship Shoal Block 84 and 107 fields using the depleted oil and gas reservoir volume and sand volume generated from our geologic modeling. The estimated storage resource results are greater when using the sand volumes derived through geologic modeling than the oil and gas reservoir data. The difference is due to the depleted oil and gas reservoir information not accounting for the water-flooded sand located below the oil/gas-water contact or unproductive sand units. Resource calculation using the sand volume obtained through geologic modeling overestimate the storage capacity as the model accounts for all sand within the formation, not just the interconnected sand.

02 PETROLEUM↗

Demonstration of Carbon Capture and Sequestration of Steam Methane Reforming Process Gas Used for Large-Scale Hydrogen Production

The large-scale, on-purpose production of hydrogen in the United States (i.e., ~4600 million standard cubic feet per day) represents one of the most significant industrial sources of CO 2 emissions within the chemical industry. Most of the hydrogen is produced by the steam methane reforming (SMR) process, through which methane and water are converted to H 2 and CO 2 , and virtually all of the co-produced CO 2 is emitted to the atmosphere. However, the process streams in the SMR plants contain CO 2 at concentrations that are amenable to utilization of conventional adsorption and emerging CO 2 capture technologies. If implemented commercially, these technologies could represent an early and sizeable impact in reducing industrial CO 2 emissions. Therefore, Air Products, working closely with the Department of Energy, has conducted a carbon capture and sequestration (CCS) project to demonstrate a first-of-a-kind retrofit system to capture CO 2 from large-scale industrial SMR plants. Working with the support of Denbury Onshore, LLC (“Denbury Onshore”) and its affiliate, Denbury Green Pipeline-Texas, LLC (“Denbury Green Pipeline”), Air Products designed, constructed and continues to operate a state-of-the-art system located at the Valero Port Arthur Refinery in Port Arthur, TX. This system concentrates the CO 2 from two SMR waste streams and delivers it into the Green Pipeline-Texas for transport to and use in the West Hastings Unit enhanced oil recovery (EOR) project. The CO 2 removal units were designed by Air Products and utilize vacuum swing adsorption (VSA) units that were retrofitted into each of the SMR trains upstream of existing pressure swing adsorption (PSA) units. This project is unique because the site has two large-scale, highly integrated SMRs located in proximity to one another. The CO 2 from this project is concentrated from 15% in the SMR waste stream to at least 98%, then flowed into the Green Pipeline-Texas along the eastern Gulf Coast. The Green Pipeline collects CO 2 from a variety of sources that is utilized for tertiary oil recovery in Texas. This project alone can prevent over 1 million tons per year of CO 2 from being emitted into the atmosphere, and thus play a major role in significantly reducing greenhouse gas emissions.

08 HYDROGEN↗

Lab-Scale Development of a Solid Sorbent for CO 2 Capture Process for Coal-Fired Power Plants

It is increasingly clear that CO 2 capture and sequestration (CCS) must play a critical role in curbing worldwide CO 2 emissions to the atmosphere. Development of these technologies to cost-effectively remove CO 2 from coal-fired power plants is very important to mitigating the impact these power plants have within the world’s power generation portfolio. Currently, conventional CO 2 capture technologies, such as aqueous-monoethanolamine based solvent systems, are prohibitively expensive and if implemented could result in a 75 to 100% increase in the cost of electricity for consumers worldwide. Solid sorbent CO 2 capture processes – such as RTI’s 3rd Generation Solid Sorbent CO 2 Capture Process – are promising alternatives to conventional, liquid solvents. Supported amine sorbents – of the nature RTI has developed – are particularly attractive due to their potential for high CO 2 loadings, excellent stability over multiple cycles, reduced corrosivity/volatility and a potential to reduce the regeneration energy needed to carry out CO 2 capture. The remaining challenges for these sorbent processes have provided the framework for the project team’s research and development and target for advancing the technology beyond lab-scale testing. Previous work in this area has failed to adequately address various technology challenges such as sorbent stability and regenerability, sorbent scale-up, improved physical strength and attrition-resistance, proper heat management and temperature control, proper solids handling, as well as the proper coupling of process engineering advancements that are tailored for a promising sorbent technology. Under a cooperative agreement with the US Department of Energy, and part of NETL’s CO 2 Capture Program, RTI has led an effort to address and mitigate the challenges associated with solid sorbent CO 2 capture. The overall objective of this project was to mitigate the technical and economic risks associated with the performance and scale-up of solid sorbent-based CO 2 capture processes, enabling subsequent larger pilot demonstrations and ultimately commercial deployment. An integrated development approach has been a key focus of this project in which sorbent development, process development, and economic analyses have informed each of the other development processes. Development efforts have focused on developing novel hybrid solids-based CO 2 capture sorbents and improving their performance stability, refining process engineering and design, and evaluating the viability of the technology through detailed economic analyses. Sorbent advancements have led to a next generation, commercially-viable CO 2 capture sorbent exhibiting performance stability in various gas environments and a physically strong fluidizable form. The team has reduced sorbent production costs and optimized the production and scale-up of novel metal-organic framework (MOF) hybrid solids-based CO 2 capture sorbents, fluidizable sorbents. Refinement of the process engineering and design at the lab-scale research unit has demonstrated promising CO 2 capture performance in simulated coal-fired flue gas conditions. Long-term testing has informed the project team on the process conditions needed to operate a solids-based system for optimal performance. Data collected from all phases of testing has been used to develop a detailed techno-economic assessment of RTI’s technology. These detailed analyses show that RTI’s technology has significant economic advantages over current amine scrubbing and potential to achieve the DOE’s Carbon Capture Program’s goal of >90% CO 2 capture rate at a cost of almost $40/tonne CO 2 captured by 2025. Through this integrated technology development approach, the project team has advanced RTI’s 3rd generation CO 2 capture technology to TRL-3, according to the DOE/FE definitions for Technology Readiness Levels. At a broader level, this project has advanced the whole of the solid sorbent CO 2 capture field, with advancements in process engineering and design, technical risk mitigation, sorbent scale-up optimization, and an understanding of the commercial viability and applicability of solid sorbent CO 2 capture technologies for the U.S. existing fleet of coal-fired power plants.

20 FOSSIL-FUELED POWER PLANTS↗

Analysis of Natural Gas Fuel Cell Plant Configurations (Rev. 1)

This report presents the results of an updated Pathway Study for natural gas fueled, fuel cell (NGFC) power systems with carbon capture and storage (CCS). The results quantify the performance and cost benefits for a series of projected gains made through the development of advances in the component technologies or improvements in plant operation and maintenance. The results represent the potential future benefits of NGFC technology development. They also provide DOE with a basis to select the most appropriate development path for NGFC, and to measure and prioritize the contribution of its R&D program to future power systems technology.

03 NATURAL GAS↗

Analysis of Natural Gas Fuel Cell Plant Configurations

This report presents the results of a Pathway Study for natural gas fueled, fuel cell (NGFC) power systems with carbon capture and sequestration (CCS). The results quantify the performance and cost benefits for a series of projected gains made through the development of advances in the component technologies or improvements in plant operation and maintenance. The design and cost bases for this pathway study closely follows the bases applied in the NETL, 2010, Bituminous Baseline report so that direct performance and cost comparisons can be made with the conventional fossil-fuel power plant results estimated in that report. Performance and cost projections for a baseline integrated Gasification Systems combined cycle (IGCC) power plant, a baseline natural gas combined cycle (NGCC) power plant, and prior coal-based integrated Gasification Systems fuel cell (IGFC) pathways, are compared with the results for the NGFC pathways. The results represent the potential future benefits of NGFC.

COE↗

Analysis of Integrated Gasification Fuel Cell Plant Configurations

This report presents the results of a Pathway Study for coal-based, integrated gasification fuel cell (IGFC) power systems with carbon capture and sequestration (CCS). The results quantify the performance and cost benefits for a series of projected gains made through the development of advanced technologies or improvements in plant operation and maintenance. The results represent the potential future benefits of IGFC technology development. They also provide DOE with a basis to select the most appropriate development path for IGFC, and to measure and prioritize the contribution of its R&D program to future power systems technology. The IGFC plants in this study apply advanced, planar, solid oxide fuel cell (SOFC) technology with separate anode and cathode off-gas steams, and incorporate anode off-gas oxy-combustion for nearly complete carbon capture. The SOFC simulations utilize the expected operating conditions and performance capabilities of this solid oxide fuel cell technology.

20 FOSSIL-FUELED POWER PLANTS↗

Underground Natural Gas Storage - Analog Studies to Geologic Storage of CO 2

The purpose of this report is to compile a stand-alone body of knowledge regarding historical and current underground natural gas storage operations that may be directly or indirectly relevant to carbon dioxide (CO 2 ) geologic storage in saline-bearing formations. This is the first of three planned documents that evaluate analog industries of CO 2 storage (the second focuses on wastewater disposal using United States [U.S.] Environmental Protection Agency [EPA] Underground Injection Control [UIC] Class I disposal wells, and the third on CO 2 enhanced oil recovery). Natural gas has been stored underground for over 100 years. This type of storage is necessary for meeting seasonal demand requirements as well as insuring against unforeseen supply disruptions. There are significant similarities that exist between natural gas storage and CO 2 geologic storage (and full-scale carbon capture and storage [CCS]) in terms of site selection and characterization, as well as operational procedures, and the equipment used. Therefore, the extensive operational history of underground natural gas storage operations provides a wealth of knowledge and lessons learned from which CO 2 storage stakeholders in industry, academia, and policy can benefit.

03 NATURAL GAS↗

Seeder, 21900 lbs, Tractor-Propelled, Construction

Based on manufacturer specifications for a John Deere Model 1990 central commodity system (CCS) air drill and a John Deere Model 1870 air hoe drill, which make up the seeder. Assumes seeder constructed entirely of steel plate. To access the model referenced in the report, please visit https://www.netl.doe.gov/energy-analysis/details?id=CB946B1B-1CEA-43E9-B024-273A3F0CE982

42 ENGINEERING↗

Advanced Ethanol Dry Mill Plant w/CCS, Construction

Calculates the amount of materials (including concrete, steel plate, and stainless steel) needed to construct an individual Advanced Dry Mill plant with CCS. Data based on construction of a conventional dry mill plant. To access the model referenced in the report, please visit https://www.netl.doe.gov/energy-analysis/details?id=22CD45F8-110D-4FEF-B7C9-772A9618F307

03 NATURAL GAS↗

BTL Plant Operation with Corn Stover Feed

Inputs and outputs for Fischer-Tropsch (FT) diesel production by a 5,000-barrel-per-day BTL plant using corn stover feed. Includes scenarios for carbon capture and sequestration (CCS) and autothermal reforming (ATR). Naphtha is a co-product. To access the model referenced in the report, please visit https://www.netl.doe.gov/energy-analysis/details?id=5B2F9747-8A07-400D-B3B4-810B06693573

09 BIOMASS FUELS↗

BTL Plant Operation with SRWC Feed

Inputs and outputs for Fischer-Tropsch diesel production by a 5,000-barrel-per-day BTL plant using SRWC feed. Includes scenarios for carbon capture and sequestration (CCS) and autothermal reforming (ATR). Naphtha is a co-product. To access the model referenced in the report, please visit https://www.netl.doe.gov/energy-analysis/details?id=BA63239E-4263-4180-82BD-D9DBEA0E01EB

09 BIOMASS FUELS↗

BTL Plant Operation with Switchgrass Feed

Inputs and outputs for FTD production by a 5,000-barrel-per-day BTL plant using switchgrass feed. Includes scenarios for carbon capture and sequestration (CCS) and autothermal reforming (ATR). Naphtha is a co-product. To access the model referenced in the report, please visit https://www.netl.doe.gov/energy-analysis/details?id=FF57463F-460F-4CE1-A4EC-26850B489EBB

09 BIOMASS FUELS↗

CBTL Plant Operation with Coal and Corn Stover Feed

Inputs and outputs for Fischer-Tropsch diesel production by a 30,000 to 50,000 barrel per day CBTL plant using Illinois No. 6 coal and Corn Stover feed. Includes scenarios for CCS and ATR (autothermal reforming). Naphtha is a co-product. To access the model referenced in the report, please visit https://www.netl.doe.gov/energy-analysis/details?id=12141C35-146E-48F2-B9E3-B0548F470835

01 COAL, LIGNITE, AND PEAT↗