Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “atmospheric model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

AATTENUATION—The Atmospheric Attenuation Model for CSP Tower Plants: A Look-Up Table for Operational Implementation

Attenuation of solar radiation between the receiver and the heliostat field in concentrated solar power (CSP) tower plants can reduce the overall system performance significantly. The attenuation varies strongly with time and the average attenuation at different sites might also vary strongly from each other. If no site specific attenuation data is available, the optimal plant design cannot be determined and rough estimations of the attenuation effect are required leading to high uncertainties of yield analysis calculations. The attenuation is caused mainly by water vapor content and aerosol particles in the lower atmospheric layer above ground. Although several on-site measurement systems have been developed during recent years, attenuation data sets are usually not available to be included during the plant project development. An Atmospheric Attenuation (AATTENUATION) model to derive the atmospheric transmittance between a heliostat and receiver on the basis of common direct normal irradiance (DNI), temperature, relative humidity, and barometric pressure measurements was developed and validated by the authors earlier. The model allows the accurate estimation of attenuation for sites with low attenuation and gives an estimation of the attenuation for less clear sites. However, the site-dependent coefficients of the AATTENUATION model had to be developed individually for each site of interest, which required time-consuming radiative transfer simulations, considering the exact location and altitude, as well as the pre-dominant aerosol type at the location. This strongly limited the application of the model despite its typically available input data. In this manuscript, a look-up table (LUT) is presented which enables the application of the AATTENUATION model at the site of interest without the necessity to perform the according complex radiative transfer calculations for each site individually. This enables the application of the AATTENUATION model for virtually all resource assessments for tower plants and in an operational mode in real time within plant monitoring systems around the world. The LUT also facilitates the generation of solar attenuation maps on the basis of long-term meteorological data sets which can be considered during resource assessment for CSP tower plant projects. The LUTs are provided together with this manuscript as supplementary files. The LUT for the AATTENUATION model was developed for a solar zenith angle (SZA) grid of 1°, an altitude grid of 100 m, 7 different standard aerosol types and the standard AFGL atmospheres for mid-latitudes and the tropics. The LUT was tested against the original version of the AATTENUATION model at 4 sites in Morocco and Spain, and it was found that the additional uncertainty introduced by the application of the LUT is negligible. With the information of latitude, longitude, altitude above mean sea level, DNI, relative humidity (RH), ambient temperature (Tair), and barometric pressure (bp), the attenuation can be now derived easily for each site of interest.

14 SOLAR ENERGY↗
NASA NTRS2013

An Atmospheric Variability Model for Venus Aerobraking Missions

Aerobraking has proven to be an enabling technology for planetary missions to Mars and has been proposed to enable low cost missions to Venus. Aerobraking saves a significant amount of propulsion fuel mass by exploiting atmospheric drag to reduce the eccentricity of the initial orbit. The solar arrays have been used as the primary drag surface and only minor modifications have been made in the vehicle design to accommodate the relatively modest aerothermal loads. However, if atmospheric density is highly variable from orbit to orbit, the mission must either accept higher aerothermal risk, a slower pace for aerobraking, or a tighter corridor likely with increased propulsive cost. Hence, knowledge of atmospheric variability is of great interest for the design of aerobraking missions. The first planetary aerobraking was at Venus during the Magellan mission. After the primary Magellan science mission was completed, aerobraking was used to provide a more circular orbit to enhance gravity field recovery. Magellan aerobraking took place between local solar times of 1100 and 1800 hrs, and it was found that the Venusian atmospheric density during the aerobraking phase had less than 10% 1 sigma orbit to orbit variability. On the other hand, at some latitudes and seasons, Martian variability can be as high as 40% 1 sigmaFrom both the MGN and PVO mission it was known that the atmosphere, above aerobraking altitudes, showed greater variability at night, but this variability was never quantified in a systematic manner. This paper proposes a model for atmospheric variability that can be used for aerobraking mission design until more complete data sets become available.

Tolson, Robert T.↗
DOE OSTI2021

Multiscale Simulation of Precipitation Over East Asia by Variable Resolution CAM-MPAS

This study evaluates the precipitation over East Asia simulated by the variable resolution CAM-MPAS featuring the Model for Prediction Across Scales (MPAS) atmospheric dynamical core coupled with the physics parameterizations of the Community Atmosphere Model (CAM) version 5.4. Two CAM-MPAS experiments, one with a global quasi-uniform resolution mesh of 120 km (MPAS-UR) and the other with a variable resolution mesh of 30 to 120 km refined over East Asia (MPAS-VR), are conducted from 1989 to 2005 following the Atmospheric Model Intercomparison Project protocol. Two regional climate model simulations at ~25 km resolution from the Coordinated Regional Downscaling Experiment East Asia second plan are also analyzed for comparison. Results show that CAM-MPAS performs better than the selected regional models in simulating the precipitation climatology over East Asia. Compared with MPAS-UR, MPAS-VR with refinement over East Asia better simulates the precipitation over and around the Tibetan Plateau (TP), the frequency distribution of light, moderate, and heavy precipitation in various regions of China, and the interannual precipitation pattern associated with the East Asian summer monsoon. The improvements in MPAS-VR relative to MPAS-UR largely come from the decreased grid spacing rather than the use of finer-scale terrain information. Particularly, decreased grid spacing is more essential for simulating the precipitation magnitude over TP and the location of peak precipitation south of TP, likely due to the better resolved physical and dynamical processes associated with orographic precipitation. The 30-120 km CAM-MPAS model is shown to be a promising tool for precipitation simulation over East Asia.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2018

VLTI-GRAVITY Measurements of Cool Evolved Stars I. Variable Photosphere and Extended Atmosphere of the Mira Star R Peg

Context. Dynamic model atmospheres of Mira stars predict variabilities in the photospheric radius and in atmospheric molecular layers which are not yet strongly constrained by observations. Aim. Here we measure the variability of the oxygen-rich Mira star R Peg in near-continuum and molecular bands. Methods. We used near-infrared K-band spectro-interferometry with a spectral resolution of about 4000 obtained at four epochs between post-maximum and minimum visual phases employing the newly available GRAVITY beam combiner at the Very Large Telescope Interferometer (VLTI). Results. Our observations show a continuum radius that is anti-correlated with the visual lightcurve. Uniform disc (UD) angular diameters at a near-continuum wavelength of 2.24 m are steadily increasing with values of 8.7 0.1 mas, 9.4 0.1 mas, 9.8 0.1 mas, and 9.9 0.1 mas at visual phases of 0.15, 0.36, 0.45, 0.53, respectively. UD diameters at a bandpass around 2.05 m, dominated by water vapour, follow the near-continuum variability at larger UD diameters between 10.7 mas and 11.7 mas. UD diameters at the CO 2-0 bandhead, instead, are correlated with the visual lightcurve and anti-correlated with the near-continuum UD diameters, with values between 12.3 mas and 11.7 mas. Conclusions. The observed anti-correlation between continuum radius and visual lightcurve is consistent with an earlier study of the oxygen-rich Mira S Lac, and with recent 1D CODEX dynamic model atmosphere predictions. The amplitude of the variation is comparable to the earlier observations of S Lac, and smaller than predicted by CODEX models. The wavelength-dependent visibility variations at our epochs can be reproduced by a set of CODEX models at model phases between 0.3 and 0.6. The anti-correlation of water vapour and CO contributions at our epochs suggests that these molecules undergo different processes in the extended atmosphere along the stellar cycle. The newly available GRAVITY instrument is suited to conducting longer time series observations, which are needed to provide strong constraints on the model-predicted intra- and inter-cycle variability.

photospheric radius↗
NASA NTRS1992

A toy model linking atmospheric thermal radiation and sea ice growth

A simplified analytical model of sea ice growth is presented where the atmosphere is in thermal radiative equilibrium with the ice. This makes the downwelling longwave radiation reaching the ice surface an internal variable rather than a specified forcing. Analytical results demonstrate how the ice state depends on properties of the ice and on the externally specified climate.

Thorndike, A. S.↗
NASA NTRS2017

Description and Evaluation of the Multiscale Online Nonhydrostatic AtmospheRe CHemistry Model (NMMB-MONARCH) Version 1.0: Gas-Phase Chemistry at Global Scale

This paper presents a comprehensive description and benchmark evaluation of the tropospheric gas-phase chemistry component of the Multiscale Online Nonhydrostatic AtmospheRe CHemistry model (NMMBMONARCH), formerly known as NMMB/BSC-CTM, that can be run on both regional and global domains. Here, we provide an extensive evaluation of a global annual cycle simulation using a variety of background surface stations (EMEP, WDCGG and CASTNET), ozonesondes (WOUDC, CMD and SHADOZ), aircraft data (MOZAIC and several campaigns), and satellite observations (SCIAMACHY and MOPITT).We also include an extensive discussion of our results in comparison to other state-of-the-art models. We note that in this study, we omitted aerosol processes and some natural emissions (lightning and volcano emissions). The model shows a realistic oxidative capacity across the globe. The seasonal cycle for CO is fairly well represented at different locations (correlations around 0.3-0.7 in surface concentrations), although concentrations are underestimated in spring and winter in the Northern Hemisphere, and are overestimated throughout the year at 800 and 500 hPa in the Southern Hemisphere. Nitrogen species are well represented in almost all locations, particularly NO2 in Europe (root mean square error - RMSE - below 5 ppb). The modeled vertical distributions of NOx and HNO3 are in excellent agreement with the observed values and the spatial and seasonal trends of tropospheric NO2 columns correspond well to observations from SCIAMACHY, capturing the highly polluted areas and the biomass burning cycle throughout the year. Over Asia, the model underestimates NOx from March to August, probably due to an underestimation of NOx emissions in the region. Overall, the comparison of the modeled CO and NO2 with MOPITT and SCIAMACHY observations emphasizes the need for more accurate emission rates from anthropogenic and biomass burning sources (i.e., specification of temporal variability).

atmospheric chemistry↗
NASA NTRS1978

Tropical sea surface temperature - An interactive one-dimensional atmosphere-ocean model

It is shown that the (cumulus) convective processes in the tropics may be described by a one-dimensional cloud model, while the near-surface ocean may similarly be described by a one-dimensional mixed-layer model. The coupling is achieved through a sea surface flux budget combined with the flux parameterizations implied by Monin-Obukhov similarity theory. The coupled one-dimensional atmosphere-ocean model is applied to the equilibrium situation in which all temperatures reach a steady state. For the ocean, the fluxes must vanish in equilibrium, but the atmosphere maintains a stable lapse rate by balancing cumulonimbus heating against net radiative cooling. All water precipitating from cumulonimbus clouds must have evaporated from the sea. It is shown that this equilibrium system is closed and determinable solely in terms of the solar constant.

Sarachik, E. S.↗
NASA NTRS2023

Modeling the Chromosphere and Transition Region of Planet-hosting Star GJ 436

Ahead of upcoming space missions intending to conduct observations of low-mass stars in the ultraviolet (UV) spectral region it becomes imperative to simultaneously conduct atmospheric modeling from the UV to the visible (VIS) and near-infrared (NIR). Investigations on extended spectral regions will help to improve the overall understanding of the diversity of spectral lines arising from very different atmospheric temperature regions. Here we investigate atmosphere models with a chromosphere and transition region for the M2.5V star GJ 436, which hosts a close-in Hot Neptune. The atmosphere models are guided by observed spectral features from the UV to the VIS/NIR originating in the chromosphere and transition region of GJ 436. High-resolution observations from the Hubble Space Telescope and Calar Alto high-Resolution search for M dwarfs with Exo-earths with Near-infrared and optical Echelle Spectrographs (CARMENES) are used to obtain an appropriate model spectrum for the investigated M dwarf. We use a large set of atomic species considered in nonlocal thermodynamic equilibrium conditions within our PHOENIX model computations to approximate the physics within the low-density atmospheric regions. In order to obtain an overall match for the nonsimultaneous observations, it is necessary to apply a linear combination of two model spectra, where one of them better reproduces the UV lines while the other better represents the lines from the VIS/NIR range. This is needed to adequately handle different activity states across the observations.

stars↗
DOE OSTI2021

Development and Evaluation of Chemistry‐Aerosol‐Climate Model CAM5‐Chem‐MAM7‐MOSAIC: Global Atmospheric Distribution and Radiative Effects of Nitrate Aerosol

Abstract An advanced aerosol treatment, with a focus on semivolatile nitrate formation, is introduced into the Community Atmosphere Model version 5 with interactive chemistry (CAM5‐chem) by coupling the Model for Simulating Aerosol Interactions and Chemistry (MOSAIC) with the 7‐mode Modal Aerosol Module (MAM7). An important feature of MOSAIC is dynamic partitioning of all condensable gases to the different fine and coarse mode aerosols, as governed by mode‐resolved thermodynamics and heterogeneous chemical reactions. Applied in the free‐running mode from 1995 to 2005 with prescribed historical climatological conditions, the model simulates global distributions of sulfate, nitrate, and ammonium in good agreement with observations and previous studies. Inclusion of nitrate resulted in ∼10% higher global average accumulation mode number concentrations, indicating enhanced growth of Aitken mode aerosols from nitrate formation. While the simulated accumulation mode nitrate burdens are high over the anthropogenic source regions, the sea‐salt and dust modes respectively constitute about 74% and 17% of the annual global average nitrate burden. Regional clear‐sky shortwave radiative cooling of up to −5 W m −2 due to nitrate is seen, with a much smaller global average cooling of −0.05 W m −2 . Significant enhancements in regional cloud condensation nuclei (at 0.1% supersaturation) and cloud droplet number concentrations are also attributed to nitrate, causing an additional global average shortwave cooling of −0.8 W m −2 . Taking into consideration of changes in both longwave and shortwave radiation under all‐sky conditions, the net change in the top of the atmosphere radiative fluxes induced by including nitrate aerosol is −0.7 W m −2 .

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2013

Additional Developments in Atmosphere Revitalization Modeling and Simulation

NASA's Advanced Exploration Systems (AES) program is developing prototype systems, demonstrating key capabilities, and validating operational concepts for future human missions beyond Earth orbit. These forays beyond the confines of earth's gravity will place unprecedented demands on launch systems. They must launch the supplies needed to sustain a crew over longer periods for exploration missions beyond earth's moon. Thus all spacecraft systems, including those for the separation of metabolic carbon dioxide and water from a crewed vehicle, must be minimized with respect to mass, power, and volume. Emphasis is also placed on system robustness both to minimize replacement parts and ensure crew safety when a quick return to earth is not possible. Current efforts are focused on improving the current state-of-the-art systems utilizing fixed beds of sorbent pellets by evaluating structured sorbents, seeking more robust pelletized sorbents, and examining alternate bed configurations to improve system efficiency and reliability. These development efforts combine testing of sub-scale systems and multi-physics computer simulations to evaluate candidate approaches, select the best performing options, and optimize the configuration of the selected approach. This paper describes the continuing development of atmosphere revitalization models and simulations in support of the Atmosphere Revitalization Recovery and Environmental Monitoring (ARREM)

Coker, Robert F.↗
NASA NTRS2013

Additional Developments in Atmosphere Revitalization Modeling and Simulation

NASA's Advanced Exploration Systems (AES) program is developing prototype systems, demonstrating key capabilities, and validating operational concepts for future human missions beyond Earth orbit. These forays beyond the confines of earth's gravity will place unprecedented demands on launch systems. They must launch the supplies needed to sustain a crew over longer periods for exploration missions beyond earth's moon. Thus all spacecraft systems, including those for the separation of metabolic carbon dioxide and water from a crewed vehicle, must be minimized with respect to mass, power, and volume. Emphasis is also placed on system robustness both to minimize replacement parts and ensure crew safety when a quick return to earth is not possible. Current efforts are focused on improving the current state-of-the-art systems utilizing fixed beds of sorbent pellets by evaluating structured sorbents, seeking more robust pelletized sorbents, and examining alternate bed configurations to improve system efficiency and reliability. These development efforts combine testing of sub-scale systems and multi-physics computer simulations to evaluate candidate approaches, select the best performing options, and optimize the configuration of the selected approach. This paper describes the continuing development of atmosphere revitalization models and simulations in support of the Atmosphere Revitalization Recovery and Environmental Monitoring (ARREM) project within the AES program.

Coker, Robert F.↗
NASA NTRS2007

Evaluating the Capacity of Global CO2 Flux and Atmospheric Transport Models to Incorporate New Satellite Observations

As we enter the new era of satellite remote sensing for CO2 and other carbon cyclerelated quantities, advanced modeling and analysis capabilities are required to fully capitalize on the new observations. Model estimates of CO2 surface flux and atmospheric transport are required for initial constraints on inverse analyses, to connect atmospheric observations to the location of surface sources and sinks, and ultimately for future projections of carbon-climate interactions. For application to current, planned, and future remotely sensed CO2 data, it is desirable that these models are accurate and unbiased at time scales from less than daily to multi-annual and at spatial scales from several kilometers or finer to global. Here we focus on simulated CO2 fluxes from terrestrial vegetation and atmospheric transport mutually constrained by analyzed meteorological fields from the Goddard Modeling and Assimilation Office for the period 1998 through 2006. Use of assimilated meteorological data enables direct model comparison to observations across a wide range of scales of variability. The biospheric fluxes are produced by the CASA model at lxi degrees on a monthly mean basis, modulated hourly with analyzed temperature and sunlight. Both physiological and biomass burning fluxes are derived using satellite observations of vegetation, burned area (as in GFED-2), and analyzed meteorology. For the purposes of comparison to CO2 data, fossil fuel and ocean fluxes are also included in the transport simulations. In this presentation we evaluate the model's ability to simulate CO2 flux and mixing ratio variability in comparison to in situ observations at sites in Northern mid latitudes and the continental tropics. The influence of key process representations is inferred. We find that the model can resolve much of the hourly to synoptic variability in the observations, although there are limits imposed by vertical resolution of boundary layer processes. The seasonal cycle and its interannual variations generally respond adequately, but discrepancies in the tropics suggest the need for a refinement of the soil moisture dependence of the respiration flux in CASA. Examples and inferences for interpretation of satellite data will be discussed. In general, the fidelity of these simulations leads us to anticipate incorporation of real-time, highly resolved remote sensing and other observations into quantitative analyses that will reduce uncertainty in the terrestrial CO2 sink and revolutionize our understanding of the key processes controlling atmospheric CO2 and its evolution with time.

Kawa, S. R.↗
NASA NTRS2006

Atmospheric drag model for Cassini orbit determination during low altitude Titan flybys

On April 16, 2005, the Cassini spacecraft performed its lowest altitude flyby of Titan to date, the Titan-5 flyby, flying 1027 km above the surface of Titan. This document discusses the development of a Titan atmospheric drag model for the purpose of the orbit determination of Cassini. Results will be presented for the Titan A flyby, the Titan-5 flyby as well as the most recent low altitude Titan flyby, Titan-7. Different solutions will be compared against OD performance in terms of the flyby B-plane parameters, spacecraft thrusting activity and drag estimates. These low altitude Titan flybys were an excellent opportunity to observe the effect of Titan's atmospheric drag on the orbit determination solution and results show that the drag was successfully modeled to provide accurate flyby solutions.

orbit determination↗
DOE OSTI2023

LANL Accident Analysis and Atmospheric Dispersion Modeling [Slides]

After completion of this course, the analyst will: 1) Understand the differences between an unmitigated analysis and a mitigated analysis; 2) Know the key receptors that a radiological and hazardous chemical accident analysis must consider; 3) Understand how to calculate a radiological release source term and a toxic chemical release source term for various phenomenology; 4) Understand how to calculate a radiological and toxic chemical health insult to key receptors and compare to consequence thresholds; 5) understand the role of atmospheric dispersion in radiological and toxic consequence calculations; 6) understand atmospheric dispersion modeling and the inputs to and outputs from the MACCS/POSTMAX codes.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1981

Combined eye-atmosphere visibility model

Existing models of the optical characteristics of the eye are combined with a recent model of optical characteristics of the atmosphere given by its modulation transfer function. This combination results in the combined eye-atmosphere performance given by the product of their modulation transfer functions. An application for the calculation of visibility thresholds in the case of a two-halves field is given.

Kaufman, Y. J.↗
NASA NTRS1984

Development of a global model for atmospheric backscatter at CO2 wavelengths

The effect of aerosol microphysical processes on the backscatter from an aerosol plume undergoing long-range atmospheric transport was studied. A numerical model which examines the effects of coagulation and sedimentation on an aerosol size distribution is under development and the initial results for a single homogeneous layer were obtained. Use was made of the SAGE/SAM II data set to study the global variation of aerosol concentration and, hence, to predict the variation of Beta sub CO2. Computer programs were written to determine the mean, median, and the probability distribution of the measured aerosol extinction as a function of altitude, latitude and geographical conditions. The first data sets analyzed in this way are under study. Data was used to study aerosol behavior over the U.S.A. and the Pacific Ocean.

Kent, G. S.↗
NASA NTRS1973

The 60 GHz radiometric local vertical sensor experiment

The experiment concept involves the use of millimeter wave radiation the atmospheric oxygen to provide vertical sensing information to a satellite-borne radiometer. The radiance profile studies require the calculation of ray brightness temperature as a function of tangential altitude and atmosphere model, and the computer program developed for this purpose is discussed. Detailed calculations have been made for a total of 12 atmosphere models, including some showing severe warning conditions. The experiment system analysis investigates the effect of various design choices on system behavior. Calculated temperature profiles are presented for a wide variety of frequencies, bandwidths, and atmosphere models. System performance is determined by the convolution of the brightness temperature and an assumed antenna pattern. A compensation scheme to account for different plateau temperatures is developed and demonstrated. The millimeter wave components developed for the local vertical sensor are discussed, with emphasis on the antenna, low noise mixer, and solid state local oscillator. It was concluded that a viable sensing technique exists, useful over a wide range of altitude with an accuracy generally on the order of 0.01 degree or better.

Grauling, C. H., Jr.↗