Measurement and application of contaminant optical constants
Contamination degrading effects on optical surfaces, discussing application to real time monitors data analysis
Linton, R. C.↗
SEARCH · Engineering Papers
Results for “SURFACE CONTAMINATION”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Ultra high vacuum adhesion testing of NERVA engine materials
The primary objective of this research program was to determine the effects of surface cleaning and deliberate gaseous contamination on the adhesion behavior of selected candidate materials for use in the NERVA nuclear rocket engine program. Using a torsion balance technique, the relationship between the normal compressive load applied to crossed rod samples and the resultant contact resistance was used to ascertain the extent of adhesion under each set of experimental conditions. In addition to an evaluation of the static adhesion behavior of selected materials combinations, the experimental apparatus was modified to permit a similar investigation relating to the effects of specific tangential displacements of the sample wires, i.e., their sliding friction behavior. During the course of this subcontract, the materials combinations 440 C vs. 440 C. pyrographite vs ZTA graphite, Nbc (graphite) vs. Nbc (graphite), and Electrolize Inconel 718 vs. Au electroplated 302 S/S were evaluated.
Source record↗
Auger measurements on T-027 samples exposed during the Skylab 2 mission
Auger electron spectroscopy measurements performed on Skylab 2 indicate a low rate of deposition of permanent, continuous film contamination on nickel and gold surfaces positioned on the antisolar side of the spacecraft. These measurements and supportive evidence indicate that for the particular locations and orientations of these samples permanent films of less than 3 nm (30 A) thickness were deposited during an exposure of 40 hours at a temperature of approximately -32 C.
Peters, P. N.↗
Adhesives and the ATS satellite
Adhesives in the ATS satellite allow the designers to save weight, simplify design and fabrication and provide thermal and electrical conductivity or resistivity as required. The selections of adhesives are restricted to those few which can pass rigorous outgassing tests in order to avoid contaminating lenses and thermal control surfaces in space. An epoxy adhesive is used to construct the honeycomb panels which constitute most of the satellite's structure. General purpose epoxy adhesives hold doublers and standoffs in place and bond the truss to its fittings. Specialized adhesives include a high temperature resistant polyamide, a flexible polyurethane and filled epoxies which conduct heat or electricity.
Hancock, F. E.↗
The Temperature Humidity Infrared Radiometer (THIR) subsystem
The infrared radiation from the earth in two spectral bands during both day and night portions of the orbit is measured. Pictures of cloud cover, three dimensional mappings of cloud cover, temperature mappings of clouds, land, and ocean surface, cirrus cloud content, atmospheric contamination, and relative humidity are provided.
Cherrix, G. T.↗
Compact acoustic levitation device for studies in fluid dynamics and material science in the laboratory and microgravity
An ultrasonic levitation device operable in both ordinary ground-based as well as in potential space-borne laboratories is described together with its various applications in the fields of fluid dynamics, material science, and light scattering. Some of the phenomena which can be studied by this instrument include surface waves on freely suspended liquids, the variations of the surface tension with temperature and contamination, the deep undercooling of materials with the temperature variations of their density and viscosity, and finally some of the optical diffraction properties of transparent substances.
Trinh, E. H.↗
Infrared reflectance spectra of Na2S with contaminant Na2CO3 - Effects of adsorbed H2O and CO2 and relation to studies of Io
A previously reported laboratory determination of the IR spectrum of Na2S is presently noted to have been incorrectly interpreted, due to the inadvertent contamination of the sample with Na2CO3. New Na2S spectra are presented, and the Na2CO3 spectrum is examined in order to demonstrate that this phase is the primary sample contaminant. Na2S is a candidate surface component on the Jupiter satellite, Io, in view of its apparent high IR brightness and spectral neutrality in the 1-5 micron range.
Nash, Douglas B.↗
Use of pure nickel and LiOH for thermal energy storage
The solid to liquid phase transformation of LiOH has been proposed as an ideal candidate thermal energy storage media for a Rankine Cycle powered electrical generation unit envisioned in Space Station based solar dynamic systems. Due to the corrosive nature of molten hydroxides, long term containment of LiOH is of concern. Pure nickel is thought to be a suitably resistant material, and a program has been instituted to measure the effects of prolonged exposure of liquid and gaseous LiOH on the mechanical properties of pure nickel alloys. Results to date indicate that negligible weight and thickness changes occurred in Ni alloys exposed to LiOH for as long as 2500 hr at 775 K, and essentially no difference in 77-900 K tensile properties could be detected between LiOH exposed and vacuum annealed Ni specimens. Although there was little sign of outward damage, microstructural examination revealed that all hydroxide contaminated tensile test specimens had surface connected intergranular cracks along the gage lengths. Two other potential problems, which have strong implications with respect to a LiOH/Ni energy storage system, were also noted during the corrosion experiments. In particular stress corrosion cracking of weld joints in pressurized vessel and permeation of hydrogen through nickel were observed.
Whittenberger, J. D.↗
Atomic oxygen interactions with FEP Teflon and silicones on LDEF
The Long Duration Exposure Facility (LDEF) spacecraft represents the first controlled unidirectional exposure of high-fluence atomic oxygen on fluorinated ethylene propylene (FEP Teflon) and silicones. The atomic oxygen erosion yield for FEP Teflon was found to be significantly in excess of previous low fluence orbital data and is an order of magnitude below that of polyimide Kapton. LDEF FEP Teflon erosion yield data as a function of angle of attack is presented. Atomic oxygen interaction with silicon polymers results in crazing of the silicones as well as deposition of dark contaminant oxidation products on adjoining surfaces. Documentation of results and possible mechanistic explanations are presented.
Banks, Bruce A.↗
Results of examination of silvered Teflon from the Long Duration Exposure Facility
Pieces of silvered Teflon thermal control blanket from seventeen locations on the Long Duration Exposure Facility (LDEF) were studied. Results of the measurements of surface texturing, and mechanical, electrical and thermal properties are presented. Photos of the blankets, scanning electron microscope pictures, infrared spectra, and surface analysis results are presented. Contamination issues relative to performance of the blankets are discussed. The variation in measured properties are reported as a function of exposure conditions.
Rousslang, Ken W.↗
High resolution electrolyte for thinning InP by anodic dissolution and its applications to EC-V profiling, defect revealing and surface passivation
An extensive experimental study was conducted using various electrolytes in an effort to find an appropriate electrolyte for anodic dissolution of InP. From the analysis of electrochemical characteristics in the dark and under different illumination levels, x ray photoelectron spectroscopy and SEM/Nomarski inspection of the surfaces, it was determined that the anodic dissolution of InP front surface layers by FAP electrolyte is a very good choice for rendering smooth surfaces, free of oxides and contaminants and with good electrical characteristics. The FAP electrolyte, based on HF, CH3COOH, and H2O2 appears to be inherently superior to previously reported electrolytes for performing accurate EC-V profiling of InP at current densities of up to 0.3 mA/sq cm. It can also be used for accurate electrochemical revealing of either precipitates or dislocation density with application to EPD mapping as a function of depth, and for defect revealing of multilayer InP structures at any depth and/or at the interfaces.
Faur, Maria↗
Seal testing of large diameter rocket motors
This investigative program examines leakage testing of elastomeric O-ring seals for a solid rocket casing and provides direction towards an improved nondestructive postassembly test. It also details test equipment for the Space Shuttle systems solid rocket boosters (SRB). The results are useful to designers of hardware for pressure containment vessels which use O-ring seals. Using several subscale seal and groove configuration test fixtures equipped with either two or three O-ring seals in series, seal integrity is investigated with both a pressure decay and flowmeter methods. Both types of test equipment adequately detect the practical range of expected seal leak rates of 1 to 0.0001 sccs. The flowmeter leak test equipment appears to reduce testing time substantially. Limited seal leakage testing is performed on full-sized rocket motor segment seals, a pre-Challenger short stack, providing comparison of bore seals to test specimen bore and face seals. The conclusions are that seal reliability, verified via a performance pressure test, can be affected by temperature, quantity of grease, test pressure, and seal pressure load direction. Potential seal failure scenarios including contamination, seal damage, and sealing surface damage are discussed. Recommendations are made for an improved test procedure.
Moore, N. B.↗
Analyzing For Light Elements By X-Ray Scattering
Nondestructive method of determining concentrations of low-atomic-number elements in liquids and solids involves measurements of Compton and Rayleigh scattering of x rays. Applied in quantitative analysis of low-atomic-number constituents of alloys, of contaminants and corrosion products on surfaces of alloys, and of fractions of hydrogen in plastics, oils, and solvents.
Ross, H. Richard↗
Nitrogen and noble gases in a glass sample from LEW88516
The Antarctic meteorite LEW88516 has been classified as a member of the SNC group of meteorites, specifically a shergottite. It is reported to be remarkably similar in mineralogy, petrogenesis and chemistry to the previously known ALH77005 shergottite, with both being compositionally distinct from other shergottites. LEW88516 shows pervasive shock features and has been found to contain glass veins attributable to a shock origin. In an effort to determine whether the glass in LEW88516 contains any of the isotopically-heavy trapped nitrogen component observed in EETA 79001 glass, as well as the related high-Ar-40/Ar-36 and high-Xe-129/Xe-132 components, we undertook an analysis of an 11.9 mg glass sample (LEW88516,4) provided to us by H. Y. McSween, Jr. as part of a consortium study of this meteorite. Nitrogen and noble gases were extracted from LEW88516,4 in a series of combustion steps at increasing temperatures followed by a final pyrolysis. Initial steps at 550 C were intended to remove any surface-sited nitrogen-containing contaminants, while the 700 C step was expected to show the onset of release of a trapped argon component, based on our previous data for EETA 79001. It was hoped that the bulk of any trapped gas release would be concentrated in one of two steps at 1100 C and approximately 1400 C, maximizing our analytical sensitivity. Results of the analysis are shown. Except for He and Ne, data obtained for the 550 C steps will be omitted from further consideration on the assumption that they represent terrestrial contamination.
Becker, R. H.↗
Contamination control and plume assessment of low-energy thrusters
Potential contamination of a spacecraft cryogenic surface by a xenon (Xe) ion generator was evaluated. The analysis involves the description of the plume exhausted from the generator with its relative component fluxes on the spacecraft surfaces, and verification of the conditions for condensation, adsorption, and sputtering at those locations. The data describing the plume fluxes and their effects on surfaces were obtained from two sources: the tests carried out with the Xe generator in a small vacuum chamber to indicate deposits and sputter on monitor slides; and the extensive tests with a mercury (Hg) ion thruster in a large vacuum chamber. The Hg thruster tests provided data on the neutrals, on low-energy ion fluxes, on high-energy ion fluxes, and on sputtered materials at several locations within the plume.
Scialdone, John J.↗
ROCKETMAS: A sounding-rocket-based remote sensing measurement of mesospheric water vapor and ozone
The ROCKETMAS rocketborne technique, based on the shuttle-borne millimeter wave atmospheric sounder (MAS), to obtain water vapor and ozone measurements with vertical resolution, is described. The concentrations of mesospheric water vapor and ozone are not well known, yet both contribute significantly to the chemical and radiative structure of that region. In situ measurements of water vapor are difficult to make because water that was absorbed on the instrument surfaces outgasses in space and contaminates the local environment of the payload. However, a remote sensing technique that uses a long pathlength through the atmosphere greatly reduces the effect of such local contamination. The 183.3 GHz line of water vapor and 184.4 GHz line of ozone are good choices for spaceborne radiometer measurements because one front-end mixer assembly can be used to simultaneously observe both gases. The design of a sounding rocket based millimeter wave radiometer for measuring water vapor and ozone with a height resolution not possible by either ground based or limb sounding techniques is described.
Croskey, C. L.↗
MIR Solar Array Return Experiment: Power Performance Measurements and Molecular Contamination Analysis Results
A solar array segment was recently removed from the Mir core module and returned for ground-based analysis. The segment, which is similar to the ones the Russians have provided for the FGB and Service Modules, was microscopically examined and disassembled by US and Russian science teams. Laboratory analyses have shown the segment to he heavily contaminated by an organic silicone coating, which was converted to an organic silicate film by reactions with atomic oxygen within the. orbital flight environment. The source of the contaminant was a silicone polymer used by the Russians as an adhesive and bonding agent during segment construction. During its life cycle, the array experienced a reduction in power performance from approx. 12%, when it was new and first deployed, to approx. 5%, when it was taken out of service. However, current-voltage measurements of three contaminated cells and three pristine, Russian standard cells have shown that very little degradation in solar array performance was due to the silicate contaminants on the solar cell surfaces. The primary sources of performance degradation is attributed to "thermal hot-spotting" or electrical arcing; orbital debris and micrometeoroid impacts; and possibly to the degradation of the solar cells and interconnects caused by radiation damage from high energy protons and electrons.
Visentine, James↗
Medical Significance of Microorganisms in Spacecraft Environment
Microorganisms can spoil food supplies, contaminate drinking water, release noxious volatile compounds, initiate allergic responses, contaminate the environment, and cause infectious diseases. International acceptability limits have been established for bacterial and fungal contaminants in air and on surfaces, and environmental monitoring is conducted to ensure compliance. Allowable levels of microorganism in water and food have also been established. Environmental monitoring of the space shuttle, the Mir, and the ISS have allowed for some general conclusions. Generally, the bacteria found in air and on interior surfaces are largely of human origin such as Staphylococcus spp., Micrococcus spp. Common environmental genera such as Bacillus spp. are the most commonly isolated bacteria from all spacecraft. Yeast species associated with humans such as Candida spp. are commonly found. Aspergillus spp., Penicillium spp., and Cladosporium spp. are the most commonly isolated filamentous fungi. Microbial levels in the environment differ significantly depending upon humidity levels, condensate accumulation, and availability of carbon sources. However, human "normal flora" of bacteria and fungi can result in serious, life-threatening diseases if human immunity is compromised. Disease incidence is expected to increase as mission duration increases.
Pierson, Duane L.↗