Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STAINLESS STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Load partitioning between single bulk grains in a two-phase duplex stainless steel during tensile loading.

The lattice strain tensor evolution for single bulk grains of austenite and ferrite in a duplex stainless steel during tensile loading to 0.02 applied strain has been investigated using in situ high-energy X-ray measurements and finite-element modeling. Single-grain X-ray diffraction lattice strain data for the eight austenite and seven ferrite grains measured show a large variation of residual lattice strains, which evolves upon deformation to the point where some grains with comparable crystallographic orientations have lattice strains different by 1.5 x 10{sup -3}, corresponding to a stress of -300MPa. The finite-element simulations of the 15 measured grains in three different spatial arrangements confirmed the complex deformation constraint and importance of local grain environment.

36 MATERIALS SCIENCE↗

Intergranular Corrosion of Feedstock Modified—Additively Manufactured Stainless Steel After Sensitization

Laser powder bed fusion (LPBF), a metal additive manufacturing technique, was conducted on feedstock-modified 316L stainless steel (316L) powder produced by ball-milling of commercial 316L and 1 wt% additive (cerium oxide—CeO 2 , lanthanum (III) nitrate hexahydrate—La(NO 3 ) 3 ·6H 2 O, and chromium nitride—CrN). The feedstock-modified LPBF-316L specimens were sensitized at 675°C for 24 h, and the influence of additives on intergranular corrosion (IGC) was investigated following ASTM G108-94 and A262-14 standards. The LPBF-316L with La(NO 3 ) 3 ·6H 2 O showed higher IGC resistance. Furthermore, the microstructure of the LPBF specimen was investigated and correlated to understand the improved IGC resistance of LPBF-316L with La(NO 3 ) 3 ·6H 2 O additive.

36 MATERIALS SCIENCE↗

Effect of radiogenic helium on stainless steel 12Cr18Ni10Ti structural changes and hydrogen sorption

The tritium trick technique was used to build-up radiogenic helium inside stainless steel 12Cr18Ni10Ti (SS). A great quantity of defects with a mean diameter of 20 nm, most probably platelet-like bubbles with {sup 3}He atoms, was observed in {sup 3}He-containing samples. The mean density of these bubbles in SS samples containing {approx}75 appm of {sup 3}He is estimated to be 6x10{sup 20} m{sup -3}. Much larger helium bubbles were observed in SS after annealing the samples at T {>=}1170 K. Thermal release of radiogenic helium occurs at T and >1500 K The presence of {sup 3}He in structural materials causes the formation of an additional state for hydrogen sorption. (authors)

36 MATERIALS SCIENCE↗

Study of Compatibility of Stainless Steel Weld Joints with Liquid Sodium-Potassium Coolants for Fission Surface Power Reactors for Lunar and Space Applications

To make a manned mission to the surface of the moon or to Mars with any significant residence time, the power requirements will make a nuclear reactor the most feasible source of energy. To prepare for such a mission, NASA has teamed with the DOE to develop Fission Surface Power technology with the goal of developing viable options. The Fission Surface Power System (FSPS) recommended as the initial baseline design includes a liquid metal reactor and primary coolant system that transfers heat to two intermediate liquid metal heat transfer loops. Each intermediate loop transfers heat to two Stirling heat exchangers that each power two Stirling converters. Both the primary and the intermediate loops will use sodium-potassium (NaK) as the liquid metal coolant, and the primary loop will operate at temperatures exceeding 600°C. The alloy selected for the heat exchangers and piping is AISI Type 316L stainless steel. The extensive experience with NaK in breeder reactor programs and with earlier space reactors for unmanned missions lends considerable confidence in using NaK as a coolant in contact with stainless steel alloys. However, the microstructure, chemical segregation, and stress state of a weld leads to the potential for corrosion and cracking. Such failures have been experienced in NaK systems that have operated for times less than the eight year goal for the FSPS. For this reason, it was necessary to evaluate candidate weld techniques and expose welds to high-temperature, flowing NaK in a closed, closely controlled system. The goal of this project was to determine the optimum weld configuration for a NaK system that will withstand service for eight years under FSPS conditions. Since the most difficult weld to make and to evaluate is the tube to tube sheet weld in the intermediate heat exchangers, it was the focus of this research. A pumped loop of flowing NaK was fabricated for exposure of candidate weld specimens at temperatures of 600°C, the expected temperature within the intermediate heat exchangers. Since metal transfer from a high-temperature region to a cooler region is a predominant mode of corrosion in liquid metal systems, specimens were placed at zones in the loop at the above temperature to evaluate the effects of both alloy component leaching and metal deposition. Microstructural analysis was performed to evaluate weld performance on control weld specimens. The research was coordinated with Oak Ridge National Laboratory (ORNL) where most of the weld samples were prepared. In addition, ORNL participated in the loop operation to assist in keeping the testing relevant to the project and to take advantage of the extensive experience in liquid metal research at ORNL.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Shock Hugoniot of forged and additively manufactured 304L stainless steel

The purpose of this research was to measure the equation of state for additively manufactured (AM) and forged 304L stainless steel using a novel experimental technique. An understanding of the dynamic behavior of AM metals is integral to their timely adoption into various applications. The Hugoniot of the AM 304L was compared to that of the forged 304L at particle velocities where the material retains a two-wave structure. This comparison enabled us to determine the sensitivity of the equation of state to microstructure as varied due to processing. Our results showed that there was a measurable difference in the measured shock velocity between the AM and forged 304L. The shock wave velocities for the AM 304L were found to be ~3% slower than those for the forged 304L at similar particle velocities. To understand these differences, properties such as densities, sound speeds, and texture were measured and compared between the forged and AM materials. Our results showed that no measurable difference was found in these properties. Additionally, it is possible that differing elastic wave amplitudes may have an effect on shock velocity.

36 MATERIALS SCIENCE↗

Shock Hugoniot of Forged and Additively Manufactured 304L Stainless Steel

The purpose of this research was to measure the equation of state for additively manufactured (AM) and forged 304L stainless steel using a novel experimental technique. An understanding of the dynamic behavior of AM metals is integral to their timely adoption into various applications. The Hugoniot of the AM 304L was compared to that of the forged 304L at particle velocities where the material retains a two-wave structure. This comparison enabled us to determine the sensitivity of the equation of state to microstructure as varied due to processing. Our results showed that there was a measurable difference in the measured shock velocity between the AM and forged 304L. The shock wave velocities for the AM 304L were found to be ~3% slower than those for the forged 304L at similar particle velocities. To understand these differences, properties such as densities, sound speeds, and texture were measured and compared between the forged and AM materials. Our results showed that no measurable difference was found in these properties. Additionally, it is possible that differing elastic wave amplitudes may influence shock velocity.

36 MATERIALS SCIENCE↗

Influence of Austenitizing Temperature on the Microstructure and Mechanical Properties of an Fe-Cr-Ni-Mo-Ti Maraging Stainless Steel

The influence of austenitizing temperature on the microstructure and mechanical properties of an Fe-Cr-Ni-Mo-Ti maraging stainless steel was investigated. The grain size, Laves phase, and retained austenite in steels given different solution treatments were observed using optical microscopy, scanning electron microscopy, and x-ray diffraction. Relationships with mechanical properties were measured by tensile testing. The grain growth rate was relatively slow at temperatures of 800-1000 °C then rapidly increased at higher temperatures. Low-temperature austenitization augmented the retention of austenite, the fraction of which decreased with an increase in austenitizing temperature. The Laves phases, which precipitated in austenite during austenitization at 800-900 °C, were preserved after quenching. The solution treatment had a significant effect on the final tensile properties of the steel after aging, due to the presence of retained austenite and Laves phase reducing its strength.

36 MATERIALS SCIENCE↗

The Elevated-Temperature Cyclic Properties of Powder Metallurgy-Hot Isostatic Pressed 316H and 316L Stainless Steel

Section III, Division 5 of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code covers construction rules for elevated-temperature nuclear components. Microreactor developers have expressed a need for advanced manufacturing processes to fabricate microreactor components to reduce manufacturing costs. Components fabricated using manufacturing processes other than conventional techniques are not currently qualified in Section III, Division 5. An expeditious approach to qualifying an advanced manufacturing process for alloys whose wrought-product form is already qualified in Division 5 is to demonstrate the resultant properties from the advanced manufacturing process are equivalent or superior to the wrought-product form. Powder metallurgy-hot isostatic pressing (PM-HIP) is a mature technology that offers many advantages that are attractive to the microreactor industry. Preliminary data show that the elevated-temperature creep-fatigue properties of PM-HIP 316H stainless steel (SS) are reduced compared to the Wrought 316H SS, which is qualified in Section III, Division 5. Work is ongoing to identify the mechanisms responsible for the reduced creep-fatigue properties and to establish acceptance criteria to confirm the adequacy of the component for service.

316H stainless steel↗

Parametric study for use of stainless steel as a material for thermal shield in PIP2IT transferline at Fermilab [Slides]

Proton Improvement Plant – II (PIP-II) has been planned at Fermilab for providing high-intensity proton beams to the laboratory’s experiments. Fermilab has undertaken the PIP-II Injector Test (PIP2IT) for integrated systems testing of critical components comprising the PIP-II front end. PIP2IT includes two cryomodules, to be tested using a pre-existing Supercritical helium refrigerator and distribution box. The PIP2IT transferline connects the Distribution box to the cryomodules of PI2IT. It contains 5 process lines as follows - supercritical 5K He supply and return lines, thermal shield supply(40K) and return(80K) lines and a sub-atmospheric 2K return line. Such cryogenic transferlines are generally provided with cylindrical thermal shields at 80K, enclosing multiple process lines. The thermal shields are cooled by dedicated cooling lines welded/brazed to the shield at a single point along the circumference. Higher thermal diffusivity provides faster cooling and uniformity o f temperature along the shield surface. Hence, Copper/Aluminium is widely used to fabricate thermal shields. However, raw material price, the cost of fabrication depending on standard sizes of pipes/tubes, often drives up the final price of thermal shields. To reduce the cost by making use of easily available stock of standard pipe/tube, it is decided to use stainless steel as a material in thermal shields for the PIP2IT transferline. To this effect, a parametric study has been undertaken to evaluate the suitability of replacing Copper/Aluminium with stainless steel in thermal shields. The low thermal conductivity of steel results in bowing of the shield due to differential temperature distribution along the circumferential direction. The resulting suitable design has limiting parameters in terms of maximum allowable length of a shield section and the maximum allowable heat transfer coefficient for cooling flow. Starting with the design specific to PIP2IT transferline, an at tempt is made to have non-dimensionalised parameters for sim! ilar thermal shields.

36 MATERIALS SCIENCE↗

Effects of nitrogen ion implantation time on tungsten films deposited by DC magnetron sputtering on AISI 410 martensitic stainless steel

Nitrogen ion implantation time on tungsten thin film deposited on surface of AISI 410 steel has been performed. Tungsten thin film produced by dc magnetron sputtering method was deposited on AISI 410 martensitic stainless steel substrates, and then the nitrogen ions were implanted on tungsten thin film. The objective of this research is to investigate the effects of implantation deposition time on surface roughness, microhardness, specific wear and corrosion rate of nitrogen implanted on tungsten film. Magnetron sputtering process was performed by using plasma gas of argon (Ar) to bombardier tungsten target (W) in a vacuum chamber with a pressure of 7.6 x 10{sup −2} torr, a voltage of 300 V, a sputter current of 80 mA for sputtered time of 10 minutes. Nitrogen implantation on tungsten film was done with an initial pressure of 3x10{sup −6} mbar, a fluence of 2 x 10{sup 17} ions/cm{sup 2}, an energy of 100 keV and implantation deposition times of 0, 20, 30 and 40 minutes. The surface roughness, microhardness, specific wear and corrosion rate of the films were evaluated by surfcorder test, Vickers microhardness test, wear test and potentiostat (galvanostat) test respectively. The results show that the nitrogen ions implanted deposition time on tungsten film can modify the surface roughness, microhardness, specific wear and corrosion rate. The minimum surface roughness, specific wear and corrosion rate can be obtained for implantation time of 20 minutes and the maximum microhardness of the film is 329 VHN (Vickers Hardness Number) for implantation time of 30 minutes. The specific wear and corrosion rate of the film depend directly on the surface roughness.

36 MATERIALS SCIENCE↗

Effects of Nucleus Density and Dendritic Growth Influenced by Ti and Nb on Solidification Structure of Fe-18 Pct Cr Ferritic Stainless Steel

The effects of nucleus density and dendritic growth influenced by Ti and Nb on the solidification structure of Fe-18 pct Cr ferritic stainless steel (FSS) ingots were investigated. The equiaxed zone ratios (EZR) were 8.5, 28.8, 67.5, and 57.3 pct in the blank, Nb-bearing, Ti-bearing, and Ti-Nb-bearing FSS ingots, respectively. The grain size was the smallest in the Ti-Nb-bearing ingot. Silicon oxide was present in the blank sample and Nb-bearing ingot, but the complex nuclei that were composed of TiO{sub x}-Ti(C, N) and TiO{sub x}-(Ti, Nb){sub x}(C, N){sub y} existed in the Ti-bearing and Ti-Nb-bearing ingots, respectively. The bulk density of the complex nucleus decreased by 70 pct when the Ti content decreased from 0.16 to 0.14 mass pct. Thermodynamic calculations indicate that the phase transformation from Ti{sub 3}O{sub 5} to Ti{sub 2}O{sub 3} was delayed in the ingot with a lower Ti content and that the Ti{sub 2}O{sub 3} shows more potential for TiN nucleation compared with Ti{sub 3}O{sub 5} according to the disregistry theory. The increased EZR mechanism was illustrated by a cellular-automaton–finite-element method with actual distribution statistics of the complex nucleus and dendritic-growth-kinetic analysis. The heterogeneous nucleation effect of the complex nucleus by Ti addition and the variations in dendritic-growth kinetics by Ti and Nb contribute to the EZR increase of FSS.

36 MATERIALS SCIENCE↗

Ultrasonic Sound Field Mapping Through Coarse Grained Cast Austenitic Stainless Steel Components

The Pacific Northwest National Laboratory (PNNL) has been involved with nondestructive examination (NDE) of coarse-grained cast austenitic stainless steel (CASS) components for over 30 years. More recent work has focused on mapping the ultrasonic sound fields generated by low-frequency phased array probes that are typically used for the evaluation of CASS materials for flaw detection and characterization. The casting process results in the formation of large grained material microstructures that are nonhomogeneous and anisotropic. The propagation of ultrasonic energy for examination of these materials results in scattering, partitioning and redirection of these sound fields. The work reported here provides an assessment of sound field formation in these materials and provides recommendations on ultrasonic inspection parameters for flaw detection in CASS components.

Ultrasonic, Phased Array, Cast Austenitic Stainles↗

Environmental resistance of oxide tags fabricated on 304L stainless steel via nanosecond pulsed laser irradiation

Nanosecond pulsed laser irradiation was used to fabricate colored, mechanically robust oxide “tags” on 304L stainless steel. Immersion in simulated seawater solution, salt fog exposure, and anodic polarization in a 3.5% NaCl solution were employed to evaluate the environmental resistance of these oxide tags. Single layer oxides outside a narrow thickness range (~ 100–150 nm) are susceptible to dissolution in chloride containing environments. The 304L substrates immediately beneath the oxides corrode severely—attributed to Cr-depletion in the melt zone during laser processing. For the first time, multilayered oxides were fabricated with pulsed laser irradiation in an effort to expand the protective thickness range while also increasing the variety of film colors attainable in this range. Layered films grown using a laser scan rate of 475 mm/s are more resistant to both localized and general corrosion than oxides fabricated at 550 mm/s. Furthermore, in the absence of pre-processing to mitigate Cr-depletion, layered films can enhance environmental stability of the system.

54 ENVIRONMENTAL SCIENCES↗

Phase structures and morphologies of tempered CA6NM stainless steel welded by hybrid laser-arc process

The post-weld tempered microstructure of hybrid laser-arc welded CA6NM, a cast low carbon martensitic stainless steel, was investigated. The microstructural evolutions from the fusion zone to the base metal were characterized in detail using optical microscopy, scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), X-ray diffraction (XRD) and microhardness techniques. The fusion zone, in its post-weld tempered condition, consisted of tempered lath martensite, residual delta-ferrite with various morphologies, reversed austenite and chromium carbides. The reversed austenite, which can be detected through both EBSD and XRD techniques, was found to be finely dispersed along the martensite lath boundaries, particularly at triple junctions. Based on the EBSD analysis, the orientation relationship between the reversed austenite and the adjacent martensite laths seemed to follow the Kurdjumov-Sachs (K-S) model. The results also revealed the presence of the reversed austenite in the different regions of the heat affected zone after post-weld tempering. The microindentation hardness distribution was measured, and correlated to the evolution of the corresponding microstructure across the welds. - Highlights: •The EBSD analysis was performed on hybrid laser-arc welded CA6NM. •The FZ consisted of tempered lath martensite, reversed austenite, carbides and δ ferrite after tempering. •The reversed γ was formed along the α′ lath boundaries, particularly at triple junctions.

36 MATERIALS SCIENCE↗

Effect of Grain Refining on Properties of a Cast Superaustenitic Stainless Steel

The goal of this study was to evaluate the industrial performance of cast high-alloy superaustenitic 19Cr-17Ni-6Mo stainless steel by refining the as-cast structure. A grain-refined, as-cast structure was achieved by the in situ inoculation with titanium nitrides (TiN) co-precipitated on previously formed spinel (MgAl{sub 2}O{sub 4}) inclusions, thus promoting heterogeneous nucleation of austenite during solidification. A homogenization heat treatment of the casting did not provide significant changes of the as-cast grain macrostructure in either the base or grain-refined steels. However, it was found that a combination of inoculation with heat treatment is an effective way of reducing interdendritic segregation. The industrial performance which includes the mechanical properties, corrosion resistance, and machinability was evaluated in the heat-treated condition for both base and inoculated steels. Tensile testing revealed improvements in ultimate tensile strength, ductility, and yield strength of the inoculated steel. The room-temperature impact properties exhibited a slight decrease in average impact energy but showed reduced variability in the inoculated steel compared to the base steel. The machining results showed that the inoculated steel had a slight improvement in machinability. The inoculated steel exhibited a lower corrosion rate but showed an increase in mass loss due to pitting. The changes in steel performance were linked to microstructure and nonmetallic inclusion families obtained by automated ASPEX SEM/EDX analysis.

36 MATERIALS SCIENCE↗

Process-Structure-Property Relationships for 316L Stainless Steel Fabricated by Additive Manufacturing and Its Implication for Component Engineering

We investigate the process-structure-property relationships for 316L stainless steel prototyping utilizing 3-D laser engineered net shaping (LENS), a commercial direct energy deposition additive manufacturing process. Our study concluded that the resultant physical metallurgy of 3-D LENS 316L prototypes is dictated by the interactive metallurgical reactions, during instantaneous powder feeding/melting, molten metal flow and liquid metal solidification. This study also showed 3-D LENS manufacturing is capable of building high strength and ductile 316L prototypes due to its fine cellular spacing from fast solidification cooling, and the well-fused epitaxial interfaces at metal flow trails and interpass boundaries. However, without further LENS process control and optimization, the deposits are vulnerable to localized hardness variation attributed to heterogeneous microstructure, i.e., the interpass heat-affected zone (HAZ) from repetitive thermal heating during successive layer depositions. Most significantly, the current deposits exhibit anisotropic tensile behavior, i.e., lower strain and/or premature interpass delamination parallel to build direction (axial). This anisotropic behavior is attributed to the presence of interpass HAZ, which coexists with flying feedstock inclusions and porosity from incomplete molten metal fusion. Our current observations and findings contribute to the scientific basis for future process control and optimization necessary for material property control and defect mitigation.

36 MATERIALS SCIENCE↗

High stored-energy breakdown tests on electrodes made of stainless steel, copper, titanium and molybdenum

IRFM have conducted resilience tests on electrodes made of Cu, stainless steel 304L, Ti and Mo against breakdowns up to 170 kV and 300 J. The tests of the 10×10 cm{sup 2} electrodes have been performed at an electrode distance d=11 mm under vacuum (P∼5×10{sup −6} mbar). No great difference in voltage holding between the materials could be identified; all materials could reach a voltage holding between 140 and 170 kV over the 11 mm gap, i.e. results scatter within a ±10% band. After exposure to ∼10000 seconds of high-voltage (HV) on-time, having accumulated ∼1000 breakdowns, the electrodes were inspected. The anodes were covered with large and small craters. The rugosity of the anodes had increased substantially, that of the cathodes to a lesser extent. The molybdenum electrodes are least affected, but this does not show in their voltage holding capability. It is hypothesized that penetrating high-energy electrons from the breakdown project heat below the surface of the anode and cause a micro-explosion of material when melting point is exceeded. Polished electrodes have also been tested. The polishing results in a substantially reduced breakdown rate in the beginning, but after having suffered a relatively small number (∼100) of breakdowns, the polished electrodes behaved the same as the unpolished ones.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗