Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROUGHNESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of electrode rinse solutions on the electrodialysis of concentrated salts

The data presented indicate that modest attention to the chemistry of the electrode rinse solution can yield as much as 56% improvement in process efficiency. When operating electrodialysis (ED) with salt concentrations greater than 10,000 mg/l (as NaCl) the amperage can be relatively high even at low voltages. To maximize the overall rate of ion transport from diluate to concentrate, there is a need to minimize resistances in the electrode cells since these can represent as much as 30% of the total resistances in the entire process and in this particular ED unit, represented resistance roughly equivalent to that within the membrane stack. This work describes the performance of a 10-cell pair, 200 cm 2 (0.02 m 2 ) per membrane, pilot ED unit operated in batch mode at 5 V potential. The feedstock to the stack was varied from 0.5% to 6% NaCl. Results from Volt-amp profiles (2.0–15 V) were used as the rationale for choosing the preferred electrode rinse solution, 90 g/l (kg/m 3 ) disodium sulfate at pH 12.5. The recommended solution of 30 g/l (kg/m 3 ) disodium sulfate at neutral pH was tested against stronger solutions (60, 90, and 120 g/l (kg/m 3 ) disodium sulfate) at neutral pH and with 1 g/l (kg/m 3 ) sodium hydroxide added to yield solutions at pH 12.5. There were stark differences in the performance of the ED unit between the solutions at pH 7 and those at pH 12.5. The slopes of the Volt-amp profiles improved indicating less resistance to ion flow at pH 12.5. Most of the difference can be attributed to the greater conductivity of sodium hydroxide compared to disodium sulfate, where even a modest addition of 1 g/l (kg/m 3 ) sodium hydroxide increased the conductivity of the solution between 8 and 20% depending on the concentration of disodium sulfate. Most notably, the initiation voltage was 2.39 ± 0.08 V with solutions at pH 7 and 1.99 V ± 0.04 V when the rinse solutions were around pH 12.5, a difference of around 0.42 V. Since the full batch runs were performed at 5.0 V, this 0.42 V differential represented a loss of 8% in process efficiency. A series of tests showed a shift in initiation voltage occurred between pH 11.5 and 12.5. Nernst equations for water electrolysis are coupled with a simple flux model that estimates the concentration of hydroxide and hydronium ions at the electrode surfaces. This model indicates that the potential demanded by the electrodes is directly linked to the current. Furthermore, there is a steep drop in the potential demanded by the anode when there is sufficient hydroxide available to generate oxygen from hydroxide as opposed to generation from water. The voltage demand is minimal at pH 12.5 and reflective of the reference standard voltage (just over 1.23 V predicted at 0.1 amps). However, the flux model predicts that the voltage demanded by the electrodes at pH 7 is 1.61 V at 0.1 amps (the lowest amperage measurable with the power pack). In conclusion, comparing this result to the reference standard (E 0 = -1.23 V) yields a satisfactory explanation for the observed difference below reference standard of 0.42 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Process design for recovering rare-earth elements from mine tailings with low rare-earth concentrations via sequential leaching and solvent extraction

Rare earth elements (REEs) are essential for advanced technologies and yet face significant supply chain risks due to their concentrated global production and limited domestic availability. Addressing this challenge requires efficient processes capable of upgrading low-grade secondary resources such as mine tailings. In this study, we developed a novel separation flowsheet that integrates sequential leaching and 2-stage solvent extraction (SX) processes to recover high-purity heavy REEs (HREEs) and light REEs (LREEs) from a simulated mine-tailing concentrate containing 2.4 wt% total REEs (TREEs; 0.6 wt% LREEs and 1.8 wt% HREEs). Sequential leaching with controlled pH adjustment selectively precipitated REEs while retaining the large amount of impurities in the solution, producing an REE-enriched leachate by following leaching processes with roughly twice the REE concentration and half the impurity concentration compared to that of single-step leaching. The optimized SX flowsheet employed Cyanex 572 to extract HREEs and Fe over LREEs, followed by Fe removal using tributyl phosphate (TBP), while the raffinate stream was processed by SX with di(2-ethylhexyl)phosphoric acid (D2EHPA) to recover LREEs under optimized conditions balancing both extraction efficiency and purity. Although increased extractant availability in the organic phase improved LREE recovery, it also increased co-extraction of Ca, underscoring trade-offs in process optimization. Both HREE- and LREE-rich solutions were subsequently precipitated into solid products via oxalate precipitation, resulting in high-purity REE solids containing ∼92.0 wt% HREEs (∼95.7 wt% TREEs) and ∼92.8 wt% LREEs (∼94.0 wt% TREEs). In conclusion, this proof-of-concept study using simulated mine tailings demonstrates a promising approach for upgrading low-grade REE resources, while highlighting the need for future validation with real materials.

Mine tailings↗
DOE OSTI2025

ED-cPSD: Fast Phase-Size Distribution via Sequential Erosion-Dilation

The Erosion-Dilation continuous Phase-Size Distribution, ED-cPSD, is an application for calculating continuous pore and particle-size distribution from digital reconstructions and/or image-based structural data. It is based on the erosion-dilation continuous phase-size distribution method. A continuous size distribution is a measure of the probability density of finding a particle or pore of a certain size. These distributions are of interest in any field of study involving porous media, including but not limited to electrochemistry, petroleum engineering, geology, and food science. The algorithm behind the software provides a computationally efficient way to calculate phase-size distributions for large domains. For a 3D battery electrode reconstruction with 1.3 x 10 8 voxels, the particle size distribution is derived in under 2 min on a desktop, while also retaining flexibility and computational efficiency for HPC-scale multi-threading. The software can handle structures with over 10 9 voxels. The algorithm is roughly 280 times faster than a previous version on the same task.

Characterization↗
DOE OSTI2022

An additively-manufactured molten salt-to-supercritical carbon di-oxide primary heat exchanger for solar thermal power generation – Design and techno-economic performance

The design and techno-economic performance of a compact additively manufactured (AM) molten salt (MS)-to-supercritical carbon di-oxide (sCO2) primary heat exchanger (PHE) for solar thermal application is described. The PHE design consists of sCO2 flow through an array of microscale pin fins while the MS flows through mm-scale rectangular channels. Constraints imposed by AM using laser powder bed fusion method are considered in the design. Structural and fluid flow simulations are performed to arrive at a viable design of the core and headers. A simplified one-dimensional steady state model for the PHE is developed including the impact of surface roughness from the AM process. A process-based cost model is used to determine the tradeoff between thermofluidic design and manufacturing cost. A parametric study is performed using the thermo-fluidic and cost models to determine the set of geometrical and flow variables that result in high power density and low cost, while restricting the pressure drop on the sCO2 side to less than 2% of line pressure. Flow rates of MS and sCO2 were varied over heat capacity rate ratios ranging from 0.2 to 1. Results indicate that it is possible to design a low-pressure drop AM PHE with an effectiveness of 90% and a power density in excess of 10 MW/m3 (including headers). Fabrication of representative nickel superalloy specimens are shown to demonstrate that low-porosity parts with the requisite dimensional tolerance of PHE core can be generated.

14 SOLAR ENERGY↗
DOE OSTI2022

The cost savings potential of controlling solar thermal collectors with storage for time-of-use electricity rates

Homes and commercial buildings account for roughly 40% of U.S. energy consumption. A significant portion of this energy consumption, and therefore utility cost, comes from domestic hot-water use. Solar collectors such as flat plate collectors, evacuated tubes, and combined photovoltaic/thermal panels, are renewable options that collect thermal energy and could help reduce utility costs. Hot water is generated by pumping a working fluid through the solar collector, where the fluid captures thermal energy via absorbed solar radiation incident on the collector surface. The collection of heat coincides with the availability of solar radiation, but the best time to use this thermal energy depends on the utility rate at a given time, which often changes throughout the day. In this work, we implement and simulate a control strategy using Transient System Simulation Tool (TRNSYS) that reduces utility costs by controlling when the system stores and uses thermal energy based on solar availability and time-of-use electricity rates. Our modeled results show that the control strategy can reduce utility costs associated with using hot water between 3% and 30%. Here, we also show how the on-peak utility rates, the size and type of the solar collectors, and the location's climate impact the results.

14 SOLAR ENERGY↗
DOE OSTI2020

Imaging hole-density inhomogeneity in arsenic-doped CdTe thin films by scanning capacitance microscopy

We report nanometer-scale hole-density imaging in As-doped CdTe films by scanning capacitance microscopy (SCM). The hole-density profiling is validated by contrasting a CdTe cross-section sample made by molecular-beam epitaxy with systematically increased As doping in a staircase pattern over the range of 10 15 -10 18 /cm 3 within a single film. In polycrystalline films, the carrier distribution is significantly nonuniform, with inhomogeneity ranging from several hundred nm to several um and hole density varying by one order of magnitude (low 10^16 to low 10 17 /cm 3 ). This nonuniformity is distributed randomly, independent of the grain structure and grain boundaries (GBs). Kelvin probe force microscopy (KPFM) maps the surface potential and is correlated to cathodoluminescence (CL) and SCM by imaging over identical areas. Higher potential and lower CL intensity are found on GBs but not by SCM contrast; this indicates positive GB charging and recombination, but not GB-specific hole-density changes. The overall KPFM potential image is in rough agreement with the SCM carrier distribution and indicates band-edge potential fluctuations. Nonuniform carrier concentration, potential fluctuations, and defect recombination can all cause voltage and performance loss in As-doped CdTe solar technology.

14 SOLAR ENERGY↗
DOE OSTI2020

Artificial linear brush abrasion of coatings for photovoltaic module first-surfaces

Natural soiling and the subsequent necessary cleaning of photovoltaic (PV) modules result in abrasion damage to the cover glass. The durability of the front glass has important economic consequences, including determining the use of anti-reflective and/or anti-soiling coatings as well as the method and frequency of operational maintenance (cleaning). Artificial linear brush abrasion using Nylon 6/12 bristles was therefore examined to explore the durability of representative PV first-surfaces, i.e., the surface of a module incident to direct solar radiation. Specimens examined include silane surface functionalized-, roughened (etched)-, porous silica-coated-, fluoropolymer-coated-, and ceramic (TiO 2 or ZrO 2 /SiO 2 /ZrO 2 /SiO 2 )-coated-glass, which are compared to monolithic-poly(methyl methacrylate) and -glass coupons. Characterization methods used in this study include: optical microscopy, ultraviolet–visible–near-infrared (UV-VIS-NIR) spectroscopy, sessile drop goniometry, white-light interferometry, atomic force microscopy (AFM), and depth-profiling X-ray photoelectron spectroscopy (XPS). The corresponding characteristics examined include: surface morphology, transmittance (i.e., optical performance), surface energy (water contact angle), surface roughness, scratch width and depth, and chemical composition, respectively. The study here was performed to determine coating failure modes; identify characterization methods that can detect nascent failures; compare the durability of popular contemporary coating materials; identify their corresponding damage characteristics; and compare slurry and dry-dust abrasion. This study will also aid in developing an abrasion standard for the PV industry.

14 SOLAR ENERGY↗
DOE OSTI2024

Enhanced passivation and stability of negative charge injected SiN x with higher nitrogen content on the boron diffused surface of n-type Si solar cells

This paper explores the potential of the negatively charged SiN x using plasma charge injection technology to passivate the front textured boron-diffused emitter of n-type Si solar cells. The high-x value single SiN x layer with x ≥ 1.30 (x = N/Si) previously developed for the planarized rear-side passivation of p-type silicon solar cells, with an excellent passivation and charge stability, was found to be unacceptable for the passivation on the front textured boron emitter of n-type cells due to a severe bulk lifetime degradation issue. Therefore, in this study, we investigated a new concept of depositing a dual-x SiN x with a low-x SiN x layer (x~1.01) on top of a high-x SiN x layer (x~1.30) for passivation of the front textured rough surface of boron diffused emitter in n-type cells. Here, the optimized dual-x SiN x stack reveals the promise of charge retention for more than 25 years in field operation as well as excellent passivation of boron-doped emitter without bulk lifetime degradation. N-type cells with the optimized dual-x SiN x after charge injection show comparable cell performance to Al 2 O 3 passivated reference cells. The results of cell-level light stability tests using one-cell minimodules exhibit cell performance decay characteristics similar to the traditional Al 2 O 3 /SiN x passivated reference module.

14 SOLAR ENERGY↗
DOE OSTI2026

A bioinspired approach for adaptive solid-solid phase change material coatings with optimized surface features for passive thermal regulation

The necessity to reduce global energy consumption calls for innovative strategies in building thermal management. Passive thermal regulation, particularly through bio-inspired designs, offers a promising avenue by mimicking nature's efficient control of optical properties. This research introduces a novel, climate-responsive coating that integrates optimized bio-inspired surface features with a solid-solid phase change material (SS-PCM) to dynamically manage solar absorptivity without adding additional thickness, enabling both heating and cooling as needed. Drawing on the photonic architectures of the Saharan silver ant and Morpho Didius butterfly, we employed a modeling and multi-objective optimization framework to tailor these surface features. Simulations reveal that surface texture, rather than the intrinsic phase transition of the SS PCM, dominates optical control. Relative to a flat SS PCM coating, optimized isotropic random roughness and broader range features yielded the highest passive heating power increase of about 144 % and 319 % respectively suitable for cold climates. Saharan ant-inspired features enhanced passive cooling for hot climates, achieving a 21.8 % improvement. For moderate climates, Butterfly-wing-inspired surface features provided a balanced enhancement of 19 % for heating and 7 % for cooling. Across all cases, the optimized surface features reduced combined heating and cooling energy demand more effectively than the baseline coating, while preserving material thickness. These findings demonstrate that climate-adaptive, optimized bio-inspired surface features can unlock the full potential of SS PCM coatings, providing a versatile pathway to significant energy savings in buildings and other applications. The methodology establishes a framework for designing next-generation adaptive envelopes that leverage natural photonic principles for high-impact, low-cost thermal regulation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hydrated doped-BaZrO 3 proton conductors studied by positron annihilation lifetime spectroscopy

The study of defect chemistry for doped BaZrO 3 proton conductors is of particular interest because of defect interactions that can affect the proton conductivity of the material. Protons incorporated due to the material's hydration can be trapped by negatively charged immobile dopants, reducing proton mobility. The reduction of the proton conduction impedes using BaZrO 3 materials in energy conversion applications at intermediate temperatures (300°C – 600°C). The probing of proton trapping in doped BaZrO 3 is hindered by the limited availability of techniques sensitive to defect chemistries. In this work, we used positron annihilation lifetime spectroscopy (PALS) to study the defect chemistry of Y-doped and Sc-doped BaZrO 3 . Using a two-state positron trapping model we showed that PALS can be used to study the defect chemistry of hydrated dense proton conductors. Positron trapping rates and lifetimes were correlated with doping levels of the materials. Probability significance t-tests were carried out for PALS parameters to verify whether there are differences/similarities for various populations: non-doped/doped, level and type of doping, high temperature, and surface effects. Further, the results revealed that the initial doping generates a significant number of traps available for positrons. Doping in yttrium increased the positron trapping rate, while this effect was not observed with scandium. Low-temperature hydration affects specimens significantly inhibiting positron trapping at undoped BaZrO 3 material and highly doped specimens. Positronium formation in rough surface layers, and highly doped specimens was detected but does not exceed 1%.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Conversion efficiency improvement of ELO GaAs solar cell, deposited on water soluble sacrificial buffer

Here, we demonstrate the improvement of power conversion efficiency of an epitaxially-lifted-off single junction GaAs solar cell deposited on a water-soluble sacrificial buffer architecture by introducing an additional germanium (Ge) interlayer between GaAs and the fluoride buffer. The epitaxial lift-off (ELO) technique has been extensively used to separate III-V device layers from their single crystal GaAs substrates. However, conventional ELO requires the use of concentrated hydrofluoric acid (HF) for extended times to etch out the sacrificial layer, subsequently degrading the surface roughness of the parent wafer. As a result, the wafer has to undergo expensive and intensive chemical mechanical polishing (CMP) processes, costing about 25% of a pristine 6-inch GaAs substrate. In our previous work, we demonstrated a method to eliminating the need for CMP post-processing by using water-assisted ELO (H 2 O-ELO). A water-soluble, 3-layer buffer architecture was developed using alkaline earth compounds. However, devices suffered low performance due to a high defect density in the GaAs active layers. A Ge interlayer was introduced to provide a more favorable surface energy for GaAs growth, which leads to an improvement of GaAs crystal quality. The Ge deposition conditions were optimized to achieve a high-quality Ge layer on triple-layer fluoride buffer. Single junction GaAs devices fabricated on Ge/(Ca,Sr)F 2 /BaF 2 /(Ca,Sr)F 2 showed improvement of solar cell performance parameters featuring increases in V oc by 23.7%, and fill factor (F.F.) by 4.9%, which results in an overall improvement of power conversion efficiency from 10.3% to 12.69%.

14 SOLAR ENERGY↗
DOE OSTI2021

Topographic and nanomechanical mapping of plutonium surfaces

Atomic force microscopy of gallium-stabilized δ-phase plutonium coupons has been used to map their topography and qualitative mechanical character, including Derjaguin-Muller-Toporov modulus, adhesion, deformation, and dissipation. Initial topographical results demonstrate that the plutonium surface is considerably rough and heterogeneous. Qualitative nanomechanical mapping revealed distinct striation patterns that are not observed in the topography images. Further investigation of the striations in the nanomechanical modes of imaging suggest that they are not measurement artifacts, or plutonium specific features. Similar investigations of stainless steel surfaces established a strong correlation between the mechanical working of the surface (i.e. cutting and grinding) and the appearance of the striations. Reimaging of the plutonium surface after moderate oxidation occurring within an inert Ar atmosphere (~1 ppm O 2 ) over the course of 13 months revealed a diminished striation pattern. It is suggested that surface stress/strain induced by the mechanical working of the metal surfaces results in the patterns of variable modulus, adhesion, deformation, and dissipation, and that these patterns are affected by the chemical changes and aging of the plutonium surface.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Learning From User Behavior: A Survey-Assist Algorithm for Longitudinal Mobility Data Collection

GPS-based travel surveys are widely used in mobility studies to gather crucial qualitative data, like purpose, transportation mode and replaced mode. However, survey response still poses a burden to users, especially in long-term mobility studies, leading to response fatigue. We explore a survey-assist strategy to ease this burden by a novel, user-level modeling approach that leverages past responses from each user to predict responses for new trips, without relying on external data sources like GIS data. We investigate three main algorithms for predicting responses: (i) clustering trips and extrapolating responses for similar trips, (ii) using random forest classification, and (iii) clustering that uses a hybrid algorithm to determine spatial structure, which is then fed as input to a classic random forest classifier. The clustering approach can flexibly predict responses for even complex qualitative survey questions; it achieved F-scores of 65%. The random forest pipeline uses architecture that restricts it to predicting three predetermined survey questions: trip purpose, mode, and replaced mode. However, it achieved F-scores of 78%. While the survey-assist approach has been implemented by several proprietary systems, to our knowledge, this is the first exploration in the academic literature. It follows that this is also the first rigorous evaluation of multiple algorithms that can implement the approach. The evaluation uses a large scale, publicly available, longitudinal dataset consisting of ~ 92k trips from 235 users over a period of roughly one and a half years. With this approach, travel surveys can be pre-filled with the predicted responses for each trip, thus streamlining the survey process for users. Combined with an active learning system that requests user input on low-confidence predictions, models can be updated and improved over time to better support the long-term collection of longitudinal qualitative data.

clustering↗
DOE OSTI2025

Exploring strain rate effects upon 3D materials using high speed in situ X-ray tomoscopy

Cellular materials are ubiquitous in our modern society. They may be stochastic gas-blown foams (e.g., polyurethane), foamed starches (e.g., cereals), or, in this case, 3D printed microlattices. Failure in these materials is often driven by surface or sub-surface defects, which may be nucleated at a surface roughness, an interior void, or inclusion interfaces that may not be typically observable. Obfuscating our understanding further, bulk materials are known to exhibit strain-rate-dependent mechanical response, making a subsurface understanding of damage even more critical. For the first time, an in situ uniaxial mechanical loading stage that simultaneously rotates specimens up to 18 Hz was fielded at a synchrotron for 3D tomographic imaging. This capability opens a plethora of materials science opportunities to explore strain rate effects in materials and examining deformation, fracture, and delamination’s (in composites) for a complete 3D picture (movie) of material response. We demonstrate the deformation of 3D printed polymer lattice structures, of three different material types, at 0.25, 1.1, and 2.2 s −1 strain rates. We successfully imaged the 3D deformation of these materials and can directly compare the same printed structure to the three material types at three strain rates, all in 3D. Material point method simulations were applied to one of the materials to better understand the role of voids on the 3D printed structure’s performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Joint routing of conventional and range-extended electric vehicles in a large metropolitan network

Range-extended electric vehicles combine the higher efficiency and environmental benefits of battery-powered electric motors with the longer mileage and autonomy of conventional internal combustion engines. This combination is particularly advantageous for time-constrained delivery routing in dense urban areas, where battery recharging along routes can be too time-consuming to economically justify the use of all-electric vehicles. However, switching from electric to conventional fossil fuel modes also results in higher costs and emissions and lower efficiency. This paper analyzes this heterogeneous vehicle routing problem and describes two solution methods: an exact branch-price-and-cut algorithm and an iterated tabu search metaheuristic. From a methodological perspective, we find that the exact algorithm consistently obtains tight lower bounds that also serve to certify the metaheuristic solutions as near-optimal. From a policy standpoint, we examine a large-scale real-world case study concerning parcel deliveries in the Chicago metropolitan area and quantify various operational metrics including energy costs and vehicle miles traveled. We find that by deploying roughly 20% of range -extended vehicles with a modest all-electric range of 33 miles, parcel distributors can save energy costs by up to 17% while incurring less than 0.5% increase in vehicle miles traveled. Increasing the range to 60 miles further reduces costs by only 4%, which can alternatively be achieved by decreasing the average service time by 1 minute or increasing driver working time by 1 hour. In conclusion, our study reveals several key areas of improvement on which vehicle manufacturers, distributors, and policy makers can focus their attention.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Superconducting magnesium diboride films for levitation of laser targets

Inertial confinement fusion targets would benefit from being levitated inside hohlraums to avoid capsule support-related implosion perturbations. Levitation inside a magnetic trap requires coating the capsule with a thin film that is superconducting at 20 K. Such non-epitaxial film growth on non-planar substrates is challenging. Here, we study Mg vapor annealing and solid-phase reactive inter-diffusion methods to form superconducting magnesium diboride (MgB 2 ) films on different planar and spherical carbon substrates, evaluating glassy carbon, polycrystalline diamond made by chemical vapor deposition, and carbon deposited by magnetron sputtering of graphite targets. Thin films of B and Mg are produced by magnetron sputtering onto stationary planar or rolling spherical substrates and annealed at either 600 or 850 °C in Mg vapor. The films are characterized by a combination of high-energy ion scattering, electron microscopy, and magnetometry. Results show that the critical superconducting temperature of resultant films depends on film microstructure and oxygen impurity content. The formation of MgB 2 films is also strongly substrate dependent, even in this case of non-epitaxial growth. Important factors to consider are oxygen outgassing of the substrate during thermal processing, substrate surface roughness, and the matching of thermal expansion coefficients of different layers in the multilayer structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Hollow-cathode chemical vapor deposition of thick, low-stress diamond-like carbon films

A radio-frequency (RF), hollow-cathode plasma source with confining magnetic field is described for the chemical vapor deposition of thick ( > 10 µm), amorphous diamond-like carbon ablator films for inertial confinement fusion applications. Plasma is characterized by optical emission spectroscopy, while properties of the resultant films are measured by a combination of profilometry, Rutherford backscattering spectrometry, elastic recoil detection analysis, X-ray diffraction, Raman spectroscopy, and atomic force microscopy. The dependence of the deposition rate, film density, elemental composition, self-bias and residual stress is reported as a function of RF power. Higher density films were found when using Ar plasma, than N 2 or H 2 plasma. The coatings produced are x-ray amorphous, exhibit low compressive stress ( ~ 100 MPa), high density ( < 1.7 g/cm 3 ), hydrogen content of ~ 30 at.%, and a low average roughness of 0.75 nm. Finally, applications of these films as tunable-density ablators for inertial confinement fusion experiments are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Detailed investigation of electrical and optical properties of textured n-type and roughened p-type tunnel oxide passivated contacts for screen-printed double-side passivated contact silicon solar cell application

Here, this paper presents detailed characterization and analyses of the optical, electrical, and contact properties of a 35 nm phosphorus-doped (n-type) polysilicon (poly-Si) and a 250 nm boron-doped (p-type) poly-Si deposited respectively on textured and roughed surface. These layers could be applied respectively to the front and rear sides of an n-type Si to produce back junction bifacial screen-printed double-side tunnel oxide passivated contacts (DS-TOPCon) solar cells. Optical and device modeling revealed a short circuit current density loss of 1.5 mA/cm 2 and 0.5 mA/cm 2 due to absorption in the front n-TOPCon and rear side p-TOPCon layers, respectively. The passivation and contact properties including metalized and unmetallized recombination current density (J 0 ), as well as contact resistivity, were determined as a function of contact firing temperature in the range of 700~800°C. The passivation quality of the front thin n-TOPCon was found to deteriorate with increased firing temperature while the rear thick p-TOPCon improved. The study showed that the simulated contact firing at 730°C resulted in the best unmetallized double-side TOPCon precursor, with an excellent implied open-circuit voltage of 730 mV and implied fill factor of ~86 %. However, the metalized J0 increased and contact resistivity decreased monotonically with the increase in the firing temperature. The 2D device simulations revealed that these layers can produce screen-printed DS-TOPCon cells with an efficiency of ~22.5 %. Solar cell modeling also showed that the DS-TOPCon solar cell efficiency can reach 24.1 % by decreasing the n-TOPCon thickness to 20 nm and lowering the full area metalized J 0 to ~100 mA/cm 2 .

14 SOLAR ENERGY↗