Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROTORS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Experimental investigation of model variable-geometry and ogee tip rotors

An experimental investigation was conducted to systematically explore the effects of inter-blade spatial relationships and pitch variations on rotor performance and wake geometry. Variable-geometry rotors consisting of various combinations of blade length, axial spacing, azimuth spacing, and collective pitch were tested at model scale in hover and forward flight. In addition, a hover test of a model rotor with an ogee blade tip design was conducted to determine its performance and wake characteristics. The results of this investigation indicate that properly selected variable geometry rotor configurations can offer substantial improvements in hover performance without adversely affecting forward flight performance. Axial spacing of alternate blades was found to provide the greatest performance benefit, and further improvements were achieved by combining azimuth spacing with axial spacing. The performance benefit appears to be related to the relief of local adverse aerodynamic phenomena produced by vortex interference. The ogee tip design was found to substantially reduce the concentrated core intensity of the tip vortex, and could thus prove beneficial for the relief of blade-vortex interaction problems. However, the ogee tip was found to reduce hover performance at model scale.

Landgrebe, A. J.↗
NASA NTRS1972

The effect of support flexibility and damping on the dynamic response of a single mass flexible rotor in elastic bearings

The dynamic unabalance response and transient motion of the single mass Jeffcott rotor in elastic bearings mounted on damped, flexible supports are discussed. A steady state analysis of the shaft and the bearing housing motion was made by assuming synchronous precession of the system. The conditions under which the support system would act as a dynamic vibration absorber at the rotor critical speed were studied. Plots of the rotor and support amplitudes, phase angles, and forces transmitted were evaluated by the computer and the performance curves were plotted by an automatic plotter unit. Curves are presented on the optimization of the support housing characteristics of attenuate the rotor synchronous unbalance response.

Kirk, R. G.↗
NASA NTRS1974

Effect of rotor-to-stator spacing on acoustic performance of a full-scale fan (QF-5) for turbofan engines

A study was made of the effect of increasing the fan rotor-to-stator spacing on the noise level of a full-scale, single-stage, 1.6-pressure-ratio fan. Noise data were obtained with axial spacing of 1.14, 1.65, and 2.27 rotor chord lengths. Over this spacing range, data indicate a reduction of 1.5 PNdb. Apparently, rotor-alone noise at the frequency at which the rotor-stator interaction noise was cut off limited the noise reduction for the QF-5 fan. It seems, however, that the reduction in sound power level with increases in spacing is potentially about 6 db over the range of spacing tested.

Balombin, J. R.↗
NASA NTRS1973

A comparison of the noise characteristics of full scale and model helicopter rotors

Full scale and model rotor noise results are compared in terms of the spectral content, the directivity patterns, and the dependence on tip speed and rotor thrust/pitch angle. Each of the three main noise sources (rotational, low-frequency broadband, and high-frequency broadband) are reviewed separately, and account is taken of the measurement angle relative to the rotor disc. Blade 'scaling' effects are discussed together with the agreement between existing theoretical and semiempirical prediction methods. It is shown that in general good agreement is obtained between the full scale and model rotors for the spectral content and the velocity and thrust dependencies, while the 'scaling' factors associated with the low-frequency broadband noise do not seem to be appropriate.

Leverton, J. W.↗
NASA NTRS1974

Holographic studies of shock waves within transonic fan rotors

NASA has funded two separate contracts to apply pulsed laser holographic interferometry to the detection of shock patterns in the outer span regions of high tip speed transonic rotors. The first holographic approach used ruby laser light reflected from a portion of the centerbody just ahead of the rotor. These holograms showed the bow wave patterns upstream of the rotor and the shock patterns just inside the blade row near the tip. The second holographic approach, on a different rotor, used light transmitted diagonally across the inlet annulus past the centerbody. This approach gave a more extensive view of the region bounded by the blade leading and trailing edges, by the part span shroud and by the blade tip. These holograms showed the passage shock emanating from the blade leading edge and a moderately strong conical shock originating at the intersection of the part span shroud leading edge and the blade suction surface.

Benser, W. A.↗
NASA NTRS1974

Aeroelastic-stability characteristics of a V/STOL tilt-rotor aircraft with hingeless blades - Correlation of analysis and test

The potential aeroelastic problems of a tilt rotor aircraft are described. The type of mathematical model required to predict such behavior is discussed and results of a design study on a specific configuration are presented. The sensitivity of the results to variation of the structural parameters is evaluated. The methodology used for analytical studies is shown to predict accurately the behavior of a full-scale rotor-pylon-wing system tested in the NASA-Ames 40- by 80-foot wind tunnel. It is concluded that there is no impediment from an aeroelastic viewpoint in designing and flying a tilt-rotor aircraft using a soft-in-plane hingeless rotor.

Alexander, H. R.↗
NASA NTRS1974

Experimental and analytical studies in tilt-rotor aeroelasticity

An overview of an experimental and analytical research program for studying the aeroelastic and dynamic characteristics of tilt-rotor VTOL aircraft is presented. Selected results from several investigations of scaled models in the Langley transonic dynamics tunnel as well as some results from a test of a flight-worthy prop rotor in the NASA Ames full-scale wind tunnel are shown and discussed with a view toward delineating various aspects of dynamic behavior peculiar to prop rotor aircraft. Included are such items as prop rotor pylon stability, whirl flutter, gust response, and blade flapping. Theoretical predictions, based on analyses developed at Langley, are shown to be in agreement with the measured stability and response behavior.

Kvaternik, R. G.↗
NASA NTRS1974

Two-stage fan. 2: Data and performance with redesigned second stage rotor uniform and distorted inlet flows

A two-stage fan with a first rotor tip speed of 1450 ft/sec (441.96 m/sec) and no inlet guide vanes was tested with uniform and distorted inlet flows, with a redesigned second rotor having a part span shroud to prevent flutter, with variable-stagger stators set in nominal positions, and without rotor casing treatment. The fan achieved a pressure ratio 2.8 at a corrected flow of 185.4 lbm/sec (84.0 kg/sec), an adiabatic efficiency of 85.0 percent, and a stall margin of 12 percent. The redesigned second rotor did not flutter. Tip radial distortion reduced the stall margin at intermediate speed, but had little effect on stall margin at high or low speeds. Hub radial distortion reduced the stall margin at design speed but increased stall margin at low speed. Circumferential distortion reduced stall pressure ratio and flow to give approximately the same stall lines with uniform inlet flow. Distortions were attenuated by the fan. For Vol. 1, see N74-11421.

Messenger, H. E.↗
NASA NTRS1974

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors, part 8

An experimental investigation was conducted with an 0.8 hub/tip ratio, single-stage, axial flow compressor to determine the potential of tandem-airfoil blading for improving the efficiency and stable operating range of compressor stages. The investigation included testing of a baseline stage with single-airfoil blading and two tandem-blade stages. The overall performance of the baseline stage and the tandem-blade stage with a 20-80% loading split was considerably below the design prediction. The other tandem-blade stage, which had a rotor with a 50-50% loading split, came within 4.5% of the design pressure rise (delta P(bar)/P(bar) sub 1) and matched the design stage efficiency. The baseline stage with single-airfoil blading, which was designed to account for the actual rotor inlet velocity profile and the effects of axial velocity ratio and secondary flow, achieved the design predicted performance. The corresponding tandem-blade stage (50-50% loading split in both blade rows) slightly exceeded the design pressure rise but was 1.5 percentage points low in efficiency. The tandem rotors tested during both phases demonstrated higher pressure rise and efficiency than the corresponding single-airfoil rotor, with identical inlet and exit airfoil angles.

Brent, J. A.↗
NASA NTRS1975

Structural analysis of wind turbine rotors for NSF-NASA Mod-0 wind power system

Preliminary estimates of vibratory loads and stresses in hingeless and teetering rotors for the proposed 100-kW wind power system are presented. Stresses in the shank areas of the 19-m (62.5-ft) blades are given for static, rated, and overload conditions. The teetering rotor has substantial advantages over the hingeless rotor with respect to shank stresses, fatigue life, and tower loading. A teetering rotor will probably be required in order to achieve a long service life in a large wind turbine exposed to periodic overload conditions.

Spera, D. A.↗
NASA NTRS1975

Wind tunnel investigation of helicopter-rotor wake effects on three helicopter fuselage models

The effects of rotor wake on helicopter fuselage aerodynamic characteristics were investigated in the Langley V/STOL tunnel. Force, moment, and pressure data were obtained on three fuselage models at various combinations of windspeed, sideslip angle, and pitch angle. The data show that the influence of rotor wake on the helicopter fuselage yawing moment imposes a significant additional thrust requirement on the tail rotor of a single-rotor helicopter at high sideslip angles.

Wilson, J. C.↗
NASA NTRS1974

The development of experimental techniques for the study of helicopter rotor noise

The features of existing wind tunnels involved in noise studies are discussed. The acoustic characteristics of the MIT low noise open jet wind tunnel are obtained by employing calibration techniques: one technique is to measure the decay of sound pressure with distance in the far field; the other technique is to utilize a speaker, which was calibrated, as a sound source. The sound pressure level versus frequency was obtained in the wind tunnel chamber and compared with the corresponding calibrated values. Fiberglas board-block units were installed on the chamber interior. The free field was increased significantly after this treatment and the chamber cut-off frequency was reduced to 160 Hz from the original designed 250 Hz. The flow field characteristics of the rotor-tunnel configuration were studied by using flow visualization techniques. The influence of open-jet shear layer on the sound transmission was studied by using an Aeolian tone as the sound source. A dynamometer system was designed to measure the steady and low harmonics of the rotor thrust. A theoretical Mach number scaling formula was developed to scale the rotational noise and blade slap noise data of model rotors to full scale helicopter rotors.

Widnall, S. E.↗
NASA NTRS1975

Digital computer program DF1758 fully coupled natural frequencies and mode shapes of a helicopter rotor blade

The analytical techniques and computer program developed in the fully-coupled rotor vibration study are described. The rotor blade natural frequency and mode shape analysis was implemented in a digital computer program designated DF1758. The program computes collective, cyclic, and scissor modes for a single blade within a specified range of frequency for specified values of rotor RPM and collective angle. The analysis includes effects of blade twist, cg offset from reference axis, and shear center offset from reference axis. Coupled inplane, out-of-plane, and torsional vibrations are considered. Normalized displacements, shear forces and moments may be printed out and Calcomp plots of natural frequencies as a function of rotor RPM may be produced.

Bennett, R. L.↗
NASA NTRS1976

Overall and blade element performance of a 1.20 pressure ratio fan stage with rotor blades reset -7 deg

A 51-cm-diam model of a fan stage for short haul aircraft was tested in a single stage compressor research facility. The rotor blades were set 7 deg toward the axial direction (opened) from the design setting angle. Surveys of the air flow conditions ahead of the rotor, between the rotor and stator, and behind the stator were made over the stable operating range of the stage. At the design speed and a weight flow of 30.9 kg/sec, the stage pressure ratio and efficiency were 1.205 and 0.85, respectively. The design speed rotor peak efficiency of 0.90 occurred at a flow rate of 32.5 kg/sec.

Lewis, G. W., Jr.↗
NASA NTRS1976

Overall and blade element performance of a 1.20-pressure-ratio fan stage with rotor blades reset -5 deg

A 51-cm-diam model of a fan stage for a short haul aircraft was tested in a single stage-compressor research facility. The rotor blades were set 5 deg toward the axial direction (opened) from design setting angle. Surveys of the air flow conditions ahead of the rotor, between the rotor and stator, and behind the stator were made over the stable operating range of the stage. At the design speed of 213.3 m/sec and a weight flow of 31.5 kg/sec, the stage pressure ratio and efficiency were 1.195 and 0.88, respectively. The design speed rotor peak efficiency of 0.91 occurred at the same flow rate.

Lewis, G. W., Jr.↗
NASA NTRS1976

The nature of flow distortions caused by rotor blade wakes

The distortion caused by wakes of rotor blades is one of the least understood phenomena in turbomachinery. An attempt is made to predict the decay characteristics of the defect in axial and tangential velocity components, and the decay of the maximum radial velocity inside the rotor wake using the momentum integral analysis. The predictions agree well with the experimental data taken at the exit of an axial flow fan operating at zero incidence. The measurements are carried out with a three sensor hot wire probe. The wake width is found to grow linearly with distance downstream and the defect in tangential velocity inside the rotor wake decays fastest of the three components. An empirical expression is also provided for the axial velocity profile of a rotor wake.

Lakshminarayana, B.↗
NASA NTRS1976

Exit flow from a transonic compressor rotor

The three dimensional unsteady flow field behind a transonic compressor rotor with a design pressure ratio of 1.6 at a tip Mach number of 1.2 has been resolved on the blade passing time scale. Quantities determined were total and static pressures, tangential flow angle, and radial flow angle. The spatial and temporal resolution achieved was sufficient to determine velocity components inside individual blade wakes and in the surrounding flow. From these measurements the flow structure is described at stations immediately behind the rotor and one chord downstream. Some dominant features of the flow just behind the rotor are large radial velocity components, large static pressure fluctuations near the blade wakes, and definite unsteadiness (in rotor coordinates) of the wakes. The wake behavior one chord downstream is described in terms of the effect of the strong mean swirl on the behavior of shear disturbances. In the outer portion of the annulus, where the mean flow approximates a solid body rotation, a strong, persistent oscillatory flow is found with 16 periods in the circumference as roughly predicted by theory. In the inner portion of the annulus the disturbances attenuate axially.

Thompkins, W. T., Jr.↗
NASA NTRS1976

Rotor Systems Research Aircraft (RSRA)

A description of the Rotor Systems Research Aircraft (RSRA) was presented, with particular emphasis on the unique systems that provide the potential for good flight/ground test facility correlation. These flight research vehicles are designed specifically with the capabilities necessary for the effective and efficient in-flight test and verification of promising new rotor concepts and supporting technology developments. The research mission and unique features of the RSRA will provide the capability to measure and separate the flight loads of the airframe and rotor, thereby allowing direct flight/ground test facility correlation of rotors as well as correlation with analytical models.

Condon, G. W.↗