Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Plastic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Test Report - Fault Current Through Graphite Filament Reinforced Plastic

Tests were performed to determine the damage to samples of composite material when a current carrying wire is shorted to the surface of the composite material, and to determine whether enough current can flow through the material to blow a fuse before damage can occur. Fault current tests were performed on samples of graphite epoxy materials. Samples consisted of six layers of IM7 graphite fiber mat in Hercules 8552 epoxy resin. A variable power supply provided up to 35 amps of current. The high voltage side of the power supply was attached to a wire at the end of a hinged arm, and the low side was attached to the edge of the sample. To test joints, the return was connected to the edge of one sample, and the high side was shorted to the top of the other sample. Tests show that when current exceeds approximately 5 amps, the graphite glows, and the epoxy melts out at the shorted contact. At higher current levels the epoxy burns. At voltages above 15 volts the epoxy outer coat is easily broken, and fire, flame, and a rise in current occur suddenly. When joints are introduced, resistance is increased, and the maximum current resulting from a short circuit to the graphite epoxy is reduced. This condition can easily result in fault current lower than the circuit breaker limit and higher than the 5 amp ignition level. The shorting contact and the joint become hot spots with melting epoxy, smoke, and fire.

Evans, R. W.↗
NASA NTRS1959

Factors Affecting the Plasticity of Sodium Chloride, Lithium Fluoride, and Magnesium Oxide Single Crystals

A study was made of the relative magnitude of the effects of various factors on the ductility of single crystals of sodium chloride (NaCl), lithium fluoride (LiF), and magnesium oxide (MgO). Specimen treatments included water-polishing, varying cleavage rate, annealing, quenching, X-irradiation, surface coating, aging, and combinations of some of these treatments. The mechanical behavior of the crystals was studied in flexure and in compression, the latter study being performed at both constant strain rate and constant load. Etch-pit studies were carried out to provide some pertinent information on the results of pretreatment on the dislocation concentration and distribution in the vicinity of the surface. The load deformation curves for these ionic single crystals show an initial region of very low slope which proved to be due to anelastic deformation. The extent of initial anelastic deformation is modified by specimen pretreatment in a way that suggests that this deformation is the result of expansion of cleaved-in dislocation loops, which can contract on the removal of the stress. The effects of the various pretreatments on the load and deflection at fracture are in accord with the prediction one might make with regard to their effect on the nucleation of fatal surface cracks. For NaCl, increases in ductility are always accompanied by increases in strength. The creep constants for NaCl are a function of treatments which affect the bulk structure but are not a function of treatments which only affect the surface.

Stearns, Carl A.↗
NASA NTRS1959

Study of Plastic Deformation in Binary Aluminum Alloys by Internal-Friction Methods

The damping capacity of several aluminum-copper alloys has been investigated during tensile elongation. This damping is shown to depend on strain rate, strain, temperature, alloy content, and heat treatment. A tentative hypothesis, based on the acceleration of solute atom diffusion by deformation-produced vacancies, is proposed to account for the observed behavior. Internal-friction maxima are observed in deformed aluminum and aluminum-copper alloys at -70 deg and -50 deg C. The peaks appear to be relatively insensitive to frequency and alloy content, but they disappear after annealing at temperatures nearing the recrystallization temperature.

Olson, E. C.↗
NASA NTRS1999

Effect of Growth Rate on Elevated Temperature Plastic Flow and Room Temperature Fracture Toughness of Directionally Solidified NiAl-31Cr-3Mo

The eutectic system Ni-33Al-31Cr-3Mo was directionally solidified at rates ranging from 7.6 to 508 mm/h. Samples were examined for microstructure and alloy chemistry, compression tested at 1200 and 1300 K, and subjected to room temperature fracture toughness measurements. Lamellar eutectic grains were formed at 12.7 mm/h; however cellular structures with a radial eutectic pattern developed at faster growth rates. Elevated temperature compression testing between 10(exp -4) to 10(exp -7)/s did not reveal an optimum growth condition, nor did any single growth condition result in a significant fracture toughness advantage. The mechanical behavior, taken together, suggests that Ni-33Al-31Cr-3Mo grown at rates from 25.4 to 254 mm/h will have nominally equivalent properties.

Whittenberger, J. Daniel↗
NASA NTRS2002

Mechanisms of Gravity-Evoked Neuronal Plasticity

The grant focuses on a gene we identified called, serum and glucocorticoid- induced kinase (SGK), during a previously funded NASA project. The abundance of SGK messenger RNA (mRNA) and protein is increased in CNS tissues from animals reared in microgravity in comparison with 1G reared animals. In the funded proposal we had three aims: 1) characterize the distribution of SGK mRNA in the developing and adult rat CNS, 2) determine if expression of enzymatically active or inactive forms of SGK in cells influenced cell morphology (neurite growth), and 2) determine if SGK is a CREB kinase - that is, a protein kinase that adds phosphate groups to the transcription factor CREB. Over the past year we have made strong progress in the two most difficult parts of the project, namely specific aims 2 and 3. In specific aim #2 we planned to express a dominant negative or a constitutively active form of SGK in PC12 cells and assay the effects on neurite growth. Several methods are available for examining the effects of a transgene on PC12 neurite growth. Relevant variables include the performance of the assay +/- serum, +/- NGF, substratum for growth, timing between transfection and assay. Over the past 8 months we have customized the assay to enable us to most readily determine the effects of transgene expression on neurite growth. We have also compared the relative utility of transfecting DNA as opposed to protein itself. We are now well positioned to study the effects of SGK on neurite growth. We have also made progress in parallel studies in primary neurons. We have made constructs which will lead to transgene expression in cultures of spinal cord neurons. Co-transfection of a reporter and the SGK constructs can now be performed.

Kalb, Robert↗
NASA NTRS2003

EEE Links, Volume 9, No. 1, January 2003 Focus on Plastic Parts

The January 2003 issue of Electronic, Electromechanical, Electric (EEE) Links is presented. The Programmable Logic Application Notes column has been reinstated in this newsletter. Written by Rich Katz of NASA's Office of Logic Design (OLD), the application notes offer technical tips intended to prevent flight design errors and enhance research, development, and use of programmable logic and elements for space flight applications. An archive of these notes columns from previous issues of EEE Links is available at http://www.klabs.org/richcontent/eeelink s/EEE Links.htm.

Source record↗
NASA NTRS1947

The Elasto-Plastic Stability of Plates

This article explains results developed from the following research: 'The Stability of Plates and Shells beyond the Elastic Limit.' A significant improvement is found in the derivation of the relations between the stress factors and the strains resulting from the instability of plates and shells. In a strict analysis, the problem reduces to the solution of two simultaneous nonlinear partial differential equations of the fourth order in the deflection and stress function, and in the approximate analysis to a single linear equation of the Bryan type. Solutions are given for the special cases of a rectangular plate buckling into a cylindrical form, and of an arbitrarily shaped plate under uniform compression. These solutions indicate that the accuracy obtained by the approximate method is satisfactory.

Ilyushin, A. A.↗
NASA NTRS2003

Characterization of Plastic flow and Resulting Micro-Textures in a Friction Stir Weld

The mechanically affected zone of a friction stir weld (FSW) cross section exhibits two distinct microstructural regions, possibly the residues of two distinct currents of metal in the FSW flow process. In this study the respective textures of these microstructural regions are investigated using orientation image mapping (OIM).

Schneider, J. A.↗
NASA NTRS2002

Motoneuron and sensory neuron plasticity to varying neuromuscular activity levels

The size and phenotypic properties of the neural and muscular elements of the neuromuscular unit are matched under normal conditions. When subjected to chronic decreases or increases in neuromuscular activity, however, the adaptations in these properties are much more limited in the neural compared with the muscular elements.

Non-NASA Center↗