Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Phase Stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

New features of different frequency generating systems due to the use of electrodeless rigidly mounted VBA quartz crystal resonator

The BVA 5 MHz crystal equipped frequency sources exhibit a new blend of performances such as 10 to 11 daily stability, 5x10-13 short term stability (1 to 30 s time intervals) and close to the carrier low phase noise (1 Hz : -120 dBc, 10 Hz : -140 dBc), whereby retaining the customary crystal oscillator benefits of small volume, high reliability and low price, as opposed to more sophisticated frequency generators which would be required to achieve comparable performances. Examples illustrating the impact of the Oscilloquartz BVA oven-controlled crystal oscillator in different frequency generating systems are presented: cesium frequency standards; hydrogen frequency standard; a precision distribution sub-system for satellite ground stations; and high hierarchy exchanges of digital networks, synchronized by the master-slave method are discussed.

Jendly, A.↗
NASA NTRS1987

Arcjet component conditions through a multistart test

A low power, dc arcjet thruster was tested for starting reliability using hydrogen-nitrogen mixtures simulating the decomposition products of hydrazine. More than 300 starts were accumulated in phases with extended burn-in periods interlaced. A high degree of flow stabilization was built into the arcjet and the power supply incorporated both rapid current regulation and a high voltage, pulsed starting circuit. A nominal current level of 10 A was maintained throughout the test. Photomicrographs of the cathode tip showed a rapid recession to a steady-state operating geometry. A target of 300 starts was selected, as this represents significantly more than anticipated (150 to 240), in missions of 10 yr or less duration. Weighings showed no apparent mass loss. Some anode erosion was observed, particularly at the entrance to the constrictor. This was attributed to the brief period during startup the arc mode attachment point spends in the high pressure region upstream of the nozzle. Based on the results obtained, startup does not appear to be performance or life limiting for the number of starts typical of operational satellite applications.

Curran, Frank M.↗
NASA NTRS1987

Arcjet component conditions through a multistart test

A low power, dc arcjet thruster was tested for starting reliability using hydrogen-nitrogen mixtures simulating the decomposition products of hydrazine. More than 300 starts were accumulated in phases with extended burn-in periods interlaced. A high degree of flow stabilization was built into the arcjet and the power supply incorporated both rapid current regulation and a high voltage, pulsed starting circuit. A nominal current level of 10 A was maintained throughout the test. Photomicrographs of the cathode tip showed a rapid recession to a steady-state operating geometry. A target of 300 starts was selected, as this represents significantly more than anticipated (150 to 240), in missions of 10 yr or less duration. Weighings showed no apparent mass loss. Some anode erosion was observed, particularly at the entrance to the constrictor. This was attributed to the brief period during startup the arc mode attachment point spends in the high pressure region upstream of the nozzle. Based on the results obtained, startup does not appear to be performance or life limiting for the number of starts typical of operational satellite applications.

Curran, Frank M.↗
NASA NTRS1987

Thermally induced phase changes, lateral heterogeneity of the mantle, continental roots, and deep slab anomalies

Factors which influence the lateral heterogeneity in density and seismic velocity with depth in the upper earth mantle are discussed. It is emphasized that most of the increases in density and seismic velocity with depth are caused by pressure-induced solid-solid phase changes in the high-density high-velocity phases of mineral assemblage, due to variations in temperature. In particular, the ilmenite form of MgSiO3 and the gamma-spinel form of Mg2SiO4 have broad stability fields in cold mantle and are not stable in hotter mantle. It is emphasized that the density and velocity anomalies associated with temperature-induced phase changes in mineral assemblage must be taken into account in the thermal models of the slabs; when these effects are accounted for, the geoid and seismic anomalies associated with subducted slabs are consistent with slab confinement to the upper mantle and with layered models of mantle convection.

Anderson, Don L.↗
NASA NTRS1988

Filling the expertise gap

Aeroelasticity, structures, and stability-and-control specialists can work in concerted fashion during the early design phases of future aircraft to achieve active control of naturally unstable configurations. In order to take full advantage of active control, attention must be given by designers to control-law synthesis, and to tools for the efficient synthesis and analysis of complex flexible-aircraft control systems. Analysts must consider interfaces among unsteady aerodynamics, structures, and control theory, as explored by the theory of analytic continuation for unsteady aerodynamics.

Abel, Irving↗
NASA NTRS1988

Attitude determination and control subsystem for the TOPEX satellite

The Ocean Topography Experiment satellite will carry a modular Attitude Determination and Control Subsystem (ADCS) which contains all equipment required for attitude determination, stabilization, and control, as well as hydrazine thruster firing control, during all mission phases. Attention is presently given to the ADCS's architecture, constituent hardware components, performance requirements, and predicted on-orbit performance compliance, with emphasis on the design and analysis of the Normal Mission Mode control algorithm furnishing the primary scientific data-acquisition operational mode. This mode's attitude determination and control of on-orbit performance is predicted to better than 43 arcsec.

Dennehy, C. J.↗
NASA NTRS1989

Influence of thickness and camber on the aeroelastic stability of supersonic throughflow fans: An engineering approach

An engineering approach was used to include the nonlinear effects of thickness and camber in an analytical aeroelastic analysis of cascades in supersonic acial flow (supersonic leading-edge locus). A hybrid code using Lighthill's nonlinear piston theory and Lanes's linear potential theory was developed to include these nonlinear effects. Lighthill's theory was used to calculate the unsteady pressures on the noninterference surface regions of the airfoils in cascade. Lane's theory was used to calculate the unsteady pressures on the remaining interference surface regions. Two airfoil profiles was investigated (a supersonic throughflow fan design and a NACA 66-206 airfoil with a sharp leading edge). Results show that compared with predictions of Lane's potential theory for flat plates, the inclusion of thickness (with or without camber) may increase or decrease the aeroelastic stability, depending on the airfoil geometry and operating conditions. When thickness effects are included in the aeroelastic analysis, inclusion of camber will influence the predicted stability in proportion to the magnitude of the added camber. The critical interblade phase angle, depending on the airfoil profile and operating conditions, may also be influenced by thickness and camber. Compared with predictions of Lane's linear potential theory, the inclusion of thickness and camber decreased the aerodynamic stifness and increased the aerodynamic damping at Mach 2 and 2.95 for a cascade of supersonic throughflow fan airfoils oscillating 180 degrees out of phase at a reduced frequency of 0.1.

Ramsey, John K.↗
NASA NTRS1988

Analysis of microalloy precipitate reversion in steels

The influence of the ferrite to austenite allotropic transformation on the stability of MXn precipitates in an iron matrix is studied. In the MX phase, M is a group IVb or Vb transition metal, such as niobium, titanium, or vanadium. X is carbon or nitrogen and n is in the range of 0.75-1.0. The application of the present model to the case of vanadium carbide reversion in a microalloyed steel is discussed.

Michal, G. M.↗
NASA NTRS1989

Buoyancy effects on morphological instability during directional solidification

The onset of morphological instability during the directional solidification of a single-phase binary alloy at constant velocity vertically upwards is treated by a linear stability analysis. The case in which a heavier solute is rejected at the solidifying interface is considered, and the effect of natural convection on the critical concentration for the onset of instability is studied. For tin containing lead, a small destabilization of the system at low growth velocities, and a large increase in the wavelength of the instability at the onset are found. Calculations show that the destabilization is enhanced as the variation of density with solute concentration is reduced, and in the limit of neutrally-dense solute, there is a long wavelength instability for which the critical solute concentration is several orders of magnitude lower than that predicted by the Mullins and Sekerka (1964) analysis in the absence of convection. For the neutrally-dense solute, a simplified analysis indicates the roles played by the interface deformation and thermal convection in promoting the instability. In particular, the destabilization is very sensitive to the ratio of crystal and melt thermal conductivities.

Coriell, S. R.↗
NASA NTRS1989

The stability of a compressible stratified shear layer

The stability of a shear layer under the effect of gravity is investigated using the compressible magnetohydrodynamic (MHD) equations, including an effective gravity term to represent the curvature effects of the flow and magnetic field line geometry. A general eigenmode equation is derived for a two-dimensional MHD fluid, and an energy-principle analysis to explain the effect of compressibility on the critical Richardson number is presented. For the case of a hyperbolic tangent shear flow and exponential density profile, it was found that, in the Boussinesq approximation, the compressibility raises the critical Richardson number from 1/4 to as much as 1/2, with the exact value depending on the value of the magnetic field at infinity. Under approximation of a strong asymptotic magnetic field, without invoking the Boussinesq approximation, it is shown both analytically and numerically that the density gradient terms cause the shear instability to be dispersive. The long-wavelength stability boundary for the Richardson number J = 0 is characterized by a normalized phase velocity c =

Wang, Z.↗
NASA NTRS1991

Influence of thickness and camber on the aeroelastic stability of supersonic throughflow fans

An engineering approach was used to include the nonlinear effects of thickness and camber in an analytical aeroelastic analysis of casecades in supersonic acial flow (supersonic leading-edge locus). A hybrid code using Lighthill's nonlinear piston theory and Lane's linear potential theory was developed to include these nonlinear effects. Lighthill's theory was used to calculate the unsteady pressures on the noninterference surface regions of the airfoils in cascade. Lane's theory was used to calculate the unsteady pressures on the remaining interference surface regions. Two airfoil profiles were investigated (a supersonic throughflow fan design and a NACA 66-206 airfoil with a sharp leading edge). Results show that compared with predictions of Lane's potential theory for flat plates, the inclusion of thickness (with or without camber) may increase or decrease the aeroelastic stability, depending on the airfoil geometry and operating conditions. When thickness effects are included in the aeroelastic analysis, inclusion of camber will influence the predicted stability in proportion to the magnitude of the added camber. The critical interblade phase angle, depending on the airfoil profile and operating conditions, may also be influenced by thickness and camber. Compared with predictions of Lane's linear potential theory, the inclusion of thickness and camber decreased the aerodynamic stiffness and increased the aerodynamic damping at Mach 2 and 2.95 for a cascade of supersonic throughflow fan airfoils oscillating 180 degrees out of phase at a reduced frequency of 0.1.

Ramsey, John K.↗
NASA NTRS1993

Bode Integrals And Feedback Control Systems

Feedback maximized in desired frequency ranges. Four of Bode integrals constitute basis of method of optimizing design of feedback control system. Integrals express frequency-domain relationships among, and constraints upon, various measures of attenuation and phase in feedback amplifiers. Applicable to similar magnitudes and phases in feedback control systems. Also used to design feedback compensators to maintain stability and performance in presence of disturbances, noise, and uncertainties in characteristics of plant to be controlled.

Kissel, Glen J.↗
NASA NTRS1994

Hydrogen storage in Earth's mantle and core

Two different approaches to explaining how hydrogen might be stored in the mantle are illustrated by a number of papers published over the past 25-30 years, but there has been little attempt to provide objective comparisons of the two. One approach invokes the presence in the mantle of dense hydrous magnesium silicates (DHMS) stable at elevated pressures and temperatures. The other involves nominally anhydrous minerals (NAM) that contain hydrogen as a minor constituent on the ppm level. Experimental studies on DHMS indicate these phases may be stable to pressures and temperatures as high at 16 GPa and 1200 C. This temperature is lower than that indicated by a mantle geotherm at 16 GPa, but may be reasonable for a subducting slab. It is possible that other DHMS could be stable to even higher pressures, but little is known about maximum temperature limits. For NAM, small amounts of hydrogen (up to several hundred ppm) have been detected in olivine, orthopyroxene, clinopyroxene, and garnet recovered from xenoliths in kimberlites, eclogites, and alkali basalts; it has been demonstrated that synthetic wadsleyite and perovskite can accommodate significant amounts of hydrogen. A number of problems are associated with each possibility. For NAM originating in the mantle, one would like to assume that the hydrogen measured in samples recovered on Earth's surface was incorporated when the phase-crystallized at high temperatures and pressures, but it could have been introduced during transport to the surface. Major problems for the DHMS proponents are that none of these phases have been found as minerals and little is yet known about their stabilities in systems containing other cations such as Fe, Al, and Ca.

Prewitt, Charles T.↗
NASA NTRS2000

Crystallography of Alumina-YAG-Eutectic

Multiple descriptions of the alumina-YAG eutectic crystallography appear in the ceramic literature. The orientation between two phases in a eutectic system has direct impact on residual stress, morphology, microstructural stability, and high temperature mechanical properties. A study to demonstrate that the different crystallographic relationships can be correlated with different growth constraints was undertaken. Fibers produced by Laser-Heated Float Zone (LHFZ) and Edge-defined Film-fed Growth (EFG) were examined. A map of the orientation relationship between Al2O3 and Y3Al5O12 and their relationship to the fiber growth axis as a function of pull rate are presented. Regions in which a single orientation predominates are identified.

Farmer, Serene C.↗
NASA NTRS2007

Guaranteeing Pointing Performance of the SDO Sun-Pointing Controllers in Light of Nonlinear Effects

The Solar Dynamics Observatory (SDO) mission is the first Space Weather Research Network mission, part of NASA s Living With a Star program.1 This program seeks to understand the changing Sun and its effects on the Solar System, life, and society. To this end, the SDO spacecraft will carry three Sun-observing instruments to geosynchronous orbit: Helioseismic and Magnetic Imager (HMI), led by Stanford University; Atmospheric Imaging Assembly (AIA), led by Lockheed Martin Space and Astrophysics Laboratory; and Extreme Ultraviolet Variability Experiment (EVE), led by the University of Colorado. Links describing the instruments in detail may be found through the SDO web site.2 The basic mission goals are to observe the Sun for a very high percentage of the 5-year mission (10-year goal) with long stretches of uninterrupted observations and with constant, high-data-rate transmission to a dedicated ground station. These goals guided the design of the spacecraft bus that will carry and service the three-instrument payload. At the time of this publication, the SDO spacecraft bus is well into the integration and testing phase at the NASA Goddard Space Flight Center (GSFC). A three-axis stabilized attitude control system (ACS) is needed both to point at the Sun accurately and to keep the roll about the Sun vector correctly positioned. The ACS has four reaction wheel modes and 2 thruster actuated modes. More details about the ACS in general and the control modes in particular can be found in Refs. [3-6]. All four of SDO s wheel-actuated control modes involve Sun-pointing controllers, as might be expected from such a mission. Science mode, during which most science data is collected, uses specialized guide telescopes to point accurately at the Sun. Inertial mode has two sub-modes, one tracks a Sun-referenced target orientation, and another maintains an absolute (star-referenced) target orientation, that both employ a Kalman filter to process data from a digital Sun sensor and two star trackers. However, this paper is concerned only with the other two modes: Safe Hold (SH) and Sun Acquisition (SA).

Starin, Scott R.↗
NASA NTRSDate not supplied

X-57 High-Lift Propeller Control Schedule Development

The NASA X-57 distributed electric propulsion flight demonstrator uses a high-lift propeller system to maintain low-speed capability with a highly loaded, cruise-efficient wing. Previous research showed that the control scheme for the high-lift propellers was a crucial factor to enable an adequate balance between stabilized glideslope control and appropriate lift margin during the approach-to-landing phase of flight. This paper expands the high-lift propeller control considerations to include all phases of low-speed flight, including preflight, taxi, takeoff, initial climb, approach, and landing. Two control modes, termed airspeed and fixed mode, are developed in this paper. The airspeed mode varies propeller torque based on equivalent airspeed to account for different phases of ground and flight operations. The fixed mode operates the high-lift propeller system at a fixed rotational speed to account for failures in the air data system, preflight checkout, and high-performance takeoff operations. Modeling of the high-lift propellers within the X-57 low-speed flight envelope shows that (1) the structural rotational speed limit of the propeller blades limits their effectiveness at higher altitudes and airspeeds, (2) the speed setting of the fixed mode is set by the maximum torque of the airspeed mode, and (3) minimizing the potential for windmilling in non-standard conditions sets the torque schedule at higher speeds. Additionally, the fixed mode is shown to provide an increased climb rate during normal takeoff operations.

Nicholas K. Borer↗
NASA NTRS2001

Gaze Stabilization During Locomotion Requires Full Body Coordination

Maintaining gaze stabilization during locomotion places substantial demands on multiple sensorimotor subsystems for precise coordination. Gaze stabilization during locomotion requires eye-head-trunk coordination (Bloomberg, et al., 1997) as well as the regulation of energy flow or shock-wave transmission through the body at high impact phases with the support surface (McDonald, et al., 1997). Allowing these excessive transmissions of energy to reach the head may compromise gaze stability. Impairments in these mechanisms may lead to the oscillopsia and decreased dynamic visual acuity seen in crewmembers returning from short and long duration spaceflight, as well as in patients with vestibular disorders (Hillman, et al., 1999). Thus, we hypothesize that stabilized gaze during locomotion results from full-body coordination of the eye-head-trunk system combined with the lower limb apparatus. The goal of this study was to determine how multiple, interdependent full- body sensorimotor subsystems aiding gaze stabilization during locomotion are functionally coordinated, and how they adaptively respond to spaceffight.

Mulavara, A. P.↗
NASA NTRS2012

Comparison of Aircraft Models and Integration Schemes for Interval Management in the TRACON

Reusable models of common elements for communication, computation, decision and control in air traffic management are necessary in order to enable simulation, analysis and assurance of emergent properties, such as safety and stability, for a given operational concept. Uncertainties due to faults, such as dropped messages, along with non-linearities and sensor noise are an integral part of these models, and impact emergent system behavior. Flight control algorithms designed using a linearized version of the flight mechanics will exhibit error due to model uncertainty, and may not be stable outside a neighborhood of the given point of linearization. Moreover, the communication mechanism by which the sensed state of an aircraft is fed back to a flight control system (such as an ADS-B message) impacts the overall system behavior; both due to sensor noise as well as dropped messages (vacant samples). Additionally simulation of the flight controller system can exhibit further numerical instability, due to selection of the integration scheme and approximations made in the flight dynamics. We examine the theoretical and numerical stability of a speed controller under the Euler and Runge-Kutta schemes of integration, for the Maintain phase for a Mid-Term (2035-2045) Interval Management (IM) Operational Concept for descent and landing operations. We model uncertainties in communication due to missed ADS-B messages by vacant samples in the integration schemes, and compare the emergent behavior of the system, in terms of stability, via the boundedness of the final system state. Any bound on the errors incurred by these uncertainties will play an essential part in a composable assurance argument required for real-time, flight-deck guidance and control systems,. Thus, we believe that the creation of reusable models, which possess property guarantees, such as safety and stability, is an innovative and essential requirement to assessing the emergent properties of novel airspace concepts of operation.

Neogi, Natasha↗