Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Oxide Particles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Elemental analyses of hypervelocity micro-particle impact sites on interplanetary dust experiment sensor surfaces

The Interplanetary Dust Experiment (IDE) had over 450 electrically active ultra-high purity metal-oxide-silicon impact detectors located on the six primary sides of the Long Duration Exposure Facility (LDEF). Hypervelocity micro-particles that struck the active sensors with enough energy to breakdown the 0.4 to 1.0 micron thick SiO2 insulator layer separating the silicon base (the negative electrode), and the 1000 A thick surface layer of aluminum (the positive electrode) caused electrical discharges that were recorded for the first year of orbit. These discharge features, which include 50 micron diameter areas where the aluminum top layer has been vaporized, facilitate the location of the impacts. The high purity Al-SiO2-Si substrates allow detection of trace (ppm) amounts of hypervelocity impactor residues. After sputtering through a layer of surface contamination, secondary ion mass spectrometry (SIMS) is used to create two-dimensional elemental ion intensity maps of micro-particle impact sites on the IDE sensors. The element intensities in the central craters of the impacts are corrected for relative ion yields and instrumental conditions and then normalized to silicon. The results are used to classify the particles' origins as 'manmade', 'natural' or 'indeterminate'. The last classification results from the presence of too little impactor residue (a frequent occurrence on leading edge impacts), analytical interference from high background contamination, the lack of information on silicon residue, the limited usefulness of data on aluminum in the central craters, or a combination of these circumstances. Several analytical 'blank' discharges were induced on flight sensors by pressing down on the sensor surface with a pure silicon shard. Analyses of these blank discharges showed that the discharge energy blasts away the layer of surface contamination. Only Si and Al were detected inside the discharge zones, including the central craters, of these features. A total of 35 impacts on leading edge sensors and 22 impacts on trailing edge sensors were analyzed.

Simon, Charles G.↗
NASA NTRS1987

Atomic oxygen effects on metals

The effect of specimen geometry on the attack of metals by atomic oxygen is addressed. This is done by extending the coupled-currents approach in metal oxidation to spherical and cylindrical geometries. Kinetic laws are derived for the rates of oxidation of samples having these geometries. It is found that the burn-up time for spherical particles of a given diameter can be as much as a factor of 3 shorter than the time required to completely oxidize a planar sample of the same thickness.

Fromhold, Albert T.↗
NASA NTRS1978

Morphology and elemental composition analysis by size of rocket particulate effluent

Particulate samples collected on six stages of a quartz crystal microbalance cascade impactor mounted in an aircraft traversing the plume of a large solid-fueled rocket are analyzed, postflight, by scanning electron microscopy (SEM) and energy dispersed X-ray (EDXRA). The results indicate the morphology and elemental composition of the particles fall into several distinct groups. Those larger than about 0.5 micron in diameter and nearly spherical in shape contain, among elements with atomic numbers of 11 and higher, only aluminum, suggesting they are aluminum oxide formed in the solid rocket fuel combustion. Still larger but less symmetrical particles contain only sodium and chlorine. Particles much smaller than 0.5 micron seem to end up as agglomerates after impaction (or during the impaction process), and show a complex elemental make-up of Na, Al, S, Cl, K, Ca, Fe and Zn. The unagglomerated single particles smaller than 0.2 micron, on the other hand, show no evidence of elements above atomic number 11 at all, suggesting they may be carbon or hydrocarbon particles.

Chuan, R. L.↗
NASA NTRS1993

Microspheres for laser velocimetry in high temperature wind tunnel

The introduction of non-intrusive measurement techniques in wind tunnel experimentation has been a turning point in error free data acquisition. Laser velocimetry has been progressively implemented and utilized in various wind tunnels; e.g. subsonic, transonic, and supersonic. The success of the laser velocimeter technique is based on an accurate measurement of scattered light by seeding particles introduced into the flow stream in the wind tunnel. Therefore, application of appropriate seeding particles will affect, to a large extent the acquired data. The seeding material used depends on the type of experiment being run. Among the seeding material for subsonic tunnel are kerosene, Kaolin, and polystyrene. Polystyrene is known to be the best because of being solid particles, having high index of refraction, capable of being made both spherical and monodisperse. However for high temperature wind tunnel testing seeding material must have an additional characteristic that is high melting point. Typically metal oxide powders such as Al2O3 with melting point 3660 F are used. The metal oxides are, however polydispersed, have a high density, and a tendency to form large agglomerate that does not closely follow the flow velocity. The addition of flame phase silica to metal oxide helps to break up the agglomerates, yet still results in a narrow band of polydispersed seeding. The less desirable utility of metal oxide in high temperature wind tunnels necessitates the search for a better alternative particle seeding which this paper addresses. The Laser Velocimetry (LV) characteristic of polystyrene makes it a prime candidate as a base material in achieving the high temperature particle seeding inexpensively. While polystyrene monodisperse seeding particle reported has been successful in a subsonic wind tunnel, it lacks the high melting point and thus is not practically usable in a high temperature wind tunnel. It is well known that rise in melting point of polystyrene can be achieved by a cross-linking technique. Since polystyrene already possesses all the desired characteristics for LV, to circumvent the low melting point, a cross-linking technique was investigated.

Ghorieshi, Anthony↗
DOE OSTI2021

Mechanistic understanding of support effect on the activity and selectivity of indium oxide catalysts for CO 2 hydrogenation

Herein we present a mechanistic study on the support effect (ZrO 2 and CeO 2 ) of In 2 O 3 catalysts in CO 2 hydrogenation by a combined experimental and computational approach. Kinetic experiments and surface characterization suggested that the activity of In 2 O 3 catalysts cannot be simply correlated with the abundance of surface oxygen vacancies (O v ) formed by either H 2 -reduction or thermal treatment, which has been frequently invoked in previous studies. The support effect should originate from the electronic interactions between In 2 O 3 and the support oxide, rather than geometric factors or the difference in the particle size of In 2 O 3 . Theoretical modelling revealed that surface O v facilitate the formation and stabilization of the formate (HCOO*) intermediate. While a carbonate-like structure is favored for CO 2 adsorption on CeO 2 -supported or unsupported In 2 O 3 catalysts, CO 2 tends to bind strongly in a bent configuration on the O v site at the In 2 O 3 -ZrO 2 interface. The distinct CO 2 adsorption structures on different supported In 2 O 3 catalysts may account for the different reaction energy profiles in the subsequent hydrogenation reactions, especially the rate-limiting step, i.e., hydrogenation of HCOO* to CH 2 O* and methoxy (CH 3 O*). The relatively higher methanol selectivity of In 2 O 3 catalyst supported on ZrO 2 with respect to that on CeO 2 are suggested to stem from the greater energy difference (Δ$E_a$) between the parallel hydrogenation and C-O bond cleavage of HCOO*, which leads to the formation of methanol and CO, respectively. We report this study underlines the important role of metal-oxide-interface in determining the catalytic behavior of oxide-supported In 2 O 3 catalysts in CO 2 conversion.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1962

Titanium-Oxygen Reactivity Study

A program has been conducted at Astronautics to investigate the likelihood of occurrence of the catastrophic oxidation of titanium alloy sheet under conditions which simulate certain cases of accidental failure of the metal while it is in contact with liquid or gaseous oxygen. Three methods of fracturing the metal were used; they consisted of mechanical puncture, tensile fracture of welded joints, and perforation by very high velocity particles. The results of the tests which have been conducted provide further evidence of the reactivity of titanium with liquid and gaseous oxygen. The evidence indicates that the rapid fracturing of titanium sheet while it is in contact with oxygen initiates the catastrophic oxidation reaction. Initiation occurred when the speed of the fracture was some few feet per second, as in both the drop-weight puncture tests and the static tensile fracture tests of welded joints, as well as when the speed was several thousand feet per second, as in the simulated micrometeoroid penetration tests. The slow propagation of a crack, however, did not initiate the reaction. It may logically be concluded that the localized frictional heat of rapid fracture and/or spontaneous oxidation (exothermic) of minute particles emanating from the fracture cause initiation of the reaction. Under conditions of slow fracture, however, the small heat generated may be adequately dissipated and the reaction is not initiated. A portion of the study conducted consisted of investigating various means by which the reaction might be retarded or prevented. Providing a "barrier" at the titanium-oxygen interface consisting of either aluminum metal or a coating of a petroleum base corrosion inhibitor appeared to be only partially effective in retarding the reaction. The accidental puncturing or similar rupturing of thin-walled pressurized oxygen tanks on missiles and space vehicle will usually constitute loss of function, and may sometimes cause their catastrophic destruction by explosive decompression regardless of the type of material used for their construction. In the case of tanks constructed of titanium alloys the added risk is incurred of catastrophic burning of the tanks. In view of this it is recommended that thin-walled tanks constructed of titanium alloys should not be used to contain liquid or gaseous oxygen.

Chafey, J. E.↗
DOE OSTI2025

Nucleation-promoting and growth-limiting synthesis of disordered rock-salt Li-ion cathode materials

Disordered rock-salt oxides and oxyfluorides are promising positive electrode materials for high-performance lithium-ion batteries free of nickel and cobalt. However, conventional synthesis methods rely on post-synthesis pulverization to achieve cycling-appropriate particle sizes, offering limited control over particle microstructure and crystallinity. This accelerates degradation and complicates secondary particle processing. Here we present a synthesis strategy that enhances nucleation while suppressing particle growth and agglomeration across various disordered rock-salt compositions, including lithium–manganese–titanium oxide, lithium–manganese–niobium oxide, and lithium–nickel–titanium oxide systems. Applied to Li 1.2 Mn 0.4 Ti 0.4 O 2 , this method yields highly crystalline, well-dispersed sub-200 nm particles that form homogeneous electrode films with stable cycling behavior. Tested in cells with lithium metal as the counter electrode, these electrodes deliver ~200 mAh/g with 85% capacity retention relative to the first cycle after 100 cycles (20 mA/g, 1.5–4.8 V), and an average discharge voltage loss of 4.8 mV per cycle, compared to 38.6% retention and 7.5 mV loss per cycle for electrodes derived from pulverized solid-state particles. This approach suggests a route to enhance the performance and durability of disordered rock-salt electrodes for sustainable lithium-ion batteries.

Batteries↗
DOE OSTI2024

Effect of Solvent Composition on Non-DLVO Forces and Oriented Attachment of Zinc Oxide Nanoparticles

Oriented attachment (OA) occurs when nanoparticles in solution align their crystallographic axes prior to colliding and subsequently fuse into single crystals. Traditional colloidal theories such as DLVO provide a framework for evaluating OA but fail to capture key particle interactions due to the atomistic details of both the crystal structure and the interfacial solution structure. Using zinc oxide as a model system, we investigated the effect of the solvent on short-ranged and long-ranged particle interactions and the resulting OA mechanism. In situ TEM imaging showed that ZnO nanocrystals in toluene undergo long-range attraction comparable to 1kT at separations of 10 nm and 3kT near particle contact. These observations were rationalized by considering non-DLVO interactions, namely dipole-dipole forces and torques between the polar ZnO nanocrystals. Langevin dynamics simulations showed stronger interactions in toluene compared to methanol solvents, consistent with the experimental results. Concurrently, we performed atomic force microscopy measurements using ZnO-coated probes for the short-ranged interaction. Our data provided valuable insights into another type of non-DLVO interaction, namely the repulsive solvation force. Specifically, the solvation force was stronger in water compared to ethanol and methanol, due to the stronger hydrogen bonding and denser packing of water molecules at the interface. In conclusion, our results highlight the importance of non-DLVO forces in a general framework for understanding and predicting particle aggregation and attachment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Alkaline Ethanol Oxidation Reaction on Carbon Supported Ternary PdNiBi Nanocatalyst using Modified Instant Reduction Synthesis Method

Direct ethanol fuel cells (DEFC) still lack active and efficient electrocatalysts for the alkaline ethanol oxidation reaction (EOR). In this work, a new instant reduction synthesis method was developed to prepare carbon supported ternary PdNiBi nanocatalysts with improved EOR activity. Synthesized catalysts were characterized with a variety of structural and compositional analysis techniques in order to correlate their morphology and surface chemistry with electrochemical performance. The modified instant reduction synthesis results in well-dispersed, spherical Pd85Ni10Bi5 nanoparticles on Vulcan XC72R support (Pd85Ni10Bi5/C(II-III)), with sizes ranging from 3.7 +/- 0.8 to 4.7 +/- 0.7 nm. On the other hand, the common instant reduction synthesis method leads to significantly agglomerated nanoparticles (Pd85Ni10Bi5/C-(I)). EOR activity and stability of these three different carbon supported PdNiBi anode catalysts with a nominal atomic ratio of 85:10:5 were probed via cyclic voltammetry and chronoamperometry using the rotating disk electrode method. Pd85Ni10Bi5/C-(II) showed the highest electrocatalytic activity (150 mA.cm(-2); 2678 mA.mg(-1)) with low onset potential (0.207 V) for EOR in alkaline medium, as compared to a commercial Pd/C and to the other synthesized ternary nanocatalysts Pd85Ni10Bi5/C-(I) and Pd85Ni10Bi5/C-(III). This new synthesis approach provides a new avenue to developing efficient, carbon supported ternary nanocatalysts for future energy conversion devices. The modified instant reduction method for synthesis of ternary Pd85Ni10Bi5/C-(II) nanocatalyst using Vulcan XC72R as carbon support initiates an agglomeration reduction, provides low average particle size, and enables enhanced activity for the alkaline ethanol oxidation reaction (EOR) compared to the common instant reduction method and to a commercial Pd/C catalyst.

Alkaline direct ethanol fuel cell↗
DOE OSTI2025

Boosting Hydrogenation of CO 2 Using Cationic Cu Atomically Dispersed on 2D γ‐Al 2 O 3 Nanosheets

The continuous development of novel catalytic approaches is crucial for advancing efficient CO 2 hydrogenation processes. Drawing inspiration from single-atom catalysis and 2D materials, we designed a new 2D single-atom catalyst with excellent thermal stability by thermally treating Cu-adsorbed γ-AlOOH nanosheets, which yielded a Cu/γ-Al 2 O 3 catalyst with high activity in the hydrogenation of CO 2 -yielding methanol (CH 3 OH), dimethyl ether (DME), and CO as products. The active Cu sites are monodispersed and highly stable due to their cationic oxidation state and their substitution for pentacoordinated aluminum (Al P ) sites on particle surfaces. This study demonstrates an efficient approach for achieving a high CO 2 hydrogenation rate (30.45 mol mol −1 h −1 ) using a catalyst system that lacks metallic Cu centers, traditionally considered essential for H₂ dissociation, and employs what was previously thought to be an inert metal oxide (γ-Al 2 O 3 ) for CO and CH 3 OH production. Ongoing mechanistic studies aim to elucidate the synergy between cationic Cu single atoms and γ-Al 2 O 3 , a Lewis acid support, in facilitating hydrogen (H 2 ) activation and methanol formation.

2D catalyst↗
DOE OSTI2022

On the Sintering Behavior of Nb2O5 and Ta2O5 Mixed Oxide Powders

A mixed oxide system consisting of Nb2O5 and Ta2O5, was subjected to annealing in air/hydrogen up to 950 °C for 1–4 h to study its sintering behavior. The thermogravimetric–differential scanning calorimetry (TGA–DSC) thermograms indicated the formation of multiple endothermic peaks at temperatures higher than 925 °C. Subsequently, a 30% Ta2O5 and 70% Nb2O5 (mol%) pellet resulted in good sintering behavior at both 900 and 950 °C. The scanning electron microscope (SEM) images corroborated these observations with necking and particle coarsening. The sintered pellets contained a 20.4 and 20.8% mixed oxide (Nb4Ta2O15) phase, along with Ta2O5 and Nb2O5, at both 900 and 950 °C, indicating the possibility of the formation of a solid solution phase. In situ high-temperature X-ray diffraction (XRD) scans also confirmed the formation of the ternary oxide phase at 6 and 19.8% at 890 and 950 °C, respectively. The Hume–Rothery rules could explain the good sintering behavior of the Ta2O5 and Nb2O5 mixed oxides. An oxide composition of 30% Ta2O5 and 70% Nb2O5 (mol%) and a sintering temperature of 950 °C appeared adequate for fabricating well-sintered oxide precursors for subsequent electrochemical polarization studies in fused salts.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microelectrode Arrays for Electrochemical Cycling of Individual Battery Particles

The electrochemical characterization of battery materials is usually performed on porous electrodes containing conductive additives, binders, and ensembles of redox-active particles at densities as high as 10 15 cm –3 . These complex structures often obscure individual battery particles’ intrinsic properties, hindering insights into the fundamentals of battery electrochemistry. To address this challenge, we developed microelectrode arrays to enable the charge and discharge of individual battery particles in liquid electrolytes. In this Methods and Protocols paper, we describe the fabrication of the microelectrode array chips, the assembly of particles onto microelectrodes, and the different types of electrochemical techniques that can be used, including galvanostatic cycling, cyclic voltammetry, potentiostatic intermittent titration, and electrochemical impedance spectroscopy. We use micron-sized lithium cobalt oxide as a model system to showcase the reliability and versatility of single-particle electrochemical experiments enabled by our microelectrode array. In conclusion, we aim to provide a detailed description to promote future uses of microelectrode arrays in fundamental research of batteries and other electrochemical systems.

25 ENERGY STORAGE↗
DOE OSTI2025

Hybrid Doping Strategy with High‐Entropy Cu/Fe Surface Modification and Zr Bulk Incorporation for Ni‐Rich Cathodes

A hybrid doping strategy combining Zr 4+ bulk doping with high-entropy Cu 2+ /Fe 3+ surface doping is developed to enhance the structural and interfacial stability of Ni-rich layered oxide cathodes. Cu and Fe are selectively introduced at the particle surface via a surface-selective ion-exchange process, forming a ≈15 nm Fe-rich layer while preserving the layered framework. Compared to the pristine cathode, the hybrid sample exhibits significantly improved electrochemical performance in both half-cell and full-cell configurations. In half-cells, the hybrid retains 88.5% and 90.2% after 100 cycles at 1C under 4.6 and 4.5 V, respectively. During high-voltage full-cell cycling, the hybrid cathode maintains over 80% capacity retention, whereas the pristine counterpart retains less than 10% under identical conditions over the same cycling period. XPS, EELS, and DEMS analyses confirm improved oxygen retention, suppressed gas evolution, and stable surface chemistry, while DFT calculations indicate enhanced Me–O bonding in the selected Fe 0.75 Cu 0.25 (Mn 1/16 Co 2/16 Ni 13/16 )O 2 surface composition, which is identified through DFT-calculated mixing energy reaching a minimum at this ratio, indicating the most thermodynamically favorable configuration. In conclusion, these results demonstrate the effectiveness of this hybrid doping strategy in mitigating coupled degradation pathways in Ni-rich cathodes.

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

Application of Atmospheric Gases and Particulate Matter to the Assessment of Urban Heat Island

Background: Urban heat island (UHI), where built areas are warmer compared to non-urban regions, increases human related diseases and mortality. A key challenge in UHI analysis is the designation of sites as urban or suburban/rural; however, the growing complexity of green spaces in urban areas and the predominance of the transportation sector in nonurban areas creates a dilemma for distinct delineation. Objectives: This study aims to utilize the variability of atmospheric components such as particulate matter (PM), inorganic gases, and volatile organic compounds (VOCs) as direct tracers of the degree of urbanization for ground-based measurements to fully comprehend UHI in convoluted regions with indistinct delineation of urban and nonurban environments. Methods: Atmospheric gases and aerosols were used as direct tracers of urbanization for UHI analysis. Inorganic gases and particulate matter were monitored in two sites in a southeastern US city with varying degrees of urbanization. VOCs were analyzed using a proton transfer reaction time-of-flight mass spectrometer. Results: The more-urbanized site exhibited warmer night conditions and elevated total oxidant levels, leading to the formation of nanometer-sized particles. Machine learning analysis revealed similar atmospheric pollutant profiles for both sites, suggesting comparable sources and variability. Biogenic VOCs were enhanced at the less-urbanized site; however, levels of anthropogenic aromatic VOCs were comparable for both sites. A comprehensive mass spectra analysis revealed distinct molecular backbones per site that further affirmed the applicability of VOCs as indicators of urbanization. Conclusion: This study concludes that VOCs provide more direct and accurate information than typical inorganic gases and PM parameters for characterizing the degree of urbanization. Further exploration of VOCs can enhance our understanding of UHI dynamics and its interaction with vegetation in urban green spaces.

Air quality sensor↗
DOE OSTI2022

Design and performance analysis of a Swirl Pintle injector for a 1 MW th pressurized oxy-coal combustor

Pressurized Oxy-coal combustion has the potential to achieve high thermal efficiency by recovering the latent heat of steam from flue gases and providing options for up to 95% carbon capture. Here, this study proposes a novel burner technology for pressurized oxy-coal combustion and investigates its operability. Three burner versions are designed and tested; no swirl, swirl numbers 0.9 and 1.2 to identify optimum design parameters and performance. A commercially available Dantec Dynamics software is used to conduct the shadowgraph experiments to observe burner performance. Coal water slurry is used as fuel with three different slurry ratios where the coal percentage by weights were 30, 40 and 50. Droplet size, distribution, spray angle and jet breakup lengths are measured and analyzed to quantify the performance. The study found that increasing the swirl number enhanced atomization. Implementing swirlers allowed the jet to spread through faster primary jet separation, thus improving atomization. In addition, higher slurry ratios improved the generation of smaller particles. However, it was also found that excessive increases in oxidizer momentums negatively impact the atomization process by jet shrinkage. The study concluded that operating a pintle burner at 1.2 swirl conditions with a 40/60 slurry ratio produces optimum performance.

42 ENGINEERING↗
DOE OSTI2021

Tracking the phase changes in micelle-based NiGa nanocatalysts for methanol synthesis under activation and working conditions

The hydrogenation of CO 2 into high energy density fuels such as methanol, where the required H 2 is obtained from renewable sources, is of utmost importance for a sustainable society. In recent years, NiGa alloys have attracted attention as promising catalyst material systems for the hydrogenation of CO 2 into methanol at ambient pressures. They thus represent an energy-saving alternative to the Cu-based catalysts employed in today's catalytic industry that require high pressures for the CO 2 hydrogenation. However, the underlying reaction mechanisms for the NiGa system are still under debate. One of the challenges here is to unravel the evolution and coexistence of the different species in the heterogeneous NiGa catalyst system under activation and reaction conditions. To shed light on their evolution under activation in H 2 and their catalytic roles under CO 2 hydrogenation working conditions on well-defined Ni 3 Ga 1 and Ni 5 Ga 3 nanoparticle (NP) catalysts, we employed a multi-probe approach in this study. It included advanced machine learning-based analysis of operando X-ray absorption spectroscopy data combined with operando powder X-ray diffraction and near ambient pressure X-ray photoelectron spectroscopy measurements, as well as reactivity studies using bed-packed mass flow reactors. In addition, we employed atomic force microscopy and scanning transmission electron microscopy for structural characterization. Under H 2 activation at 1 bar total pressure, we concluded the formation of metallic Ni, starting for Ni 3 Ga 1 at 300 °C, and for Ni 5 Ga 3 at 400 °C. At higher temperatures, the formation of NiGa alloys follows. The α'-Ni 3 Ga 1 alloy phase is predominantly formed for the Ni 3 Ga 1 NPs, while the coexistence of α'-Ni 3 Ga 1 , δ-Ni 5 Ga 3 and Ga 2 O 3 phases is observed for the Ni 5 Ga 3 NPs after the H 2 activation. The formation of the Ga 2 O 3 phase also results in the presence of excess metallic Ni. Under CO 2 hydrogenation reaction conditions, Ga partially oxidizes again to form a Ga 2 O 3 -rich particle shell for both NP compositions, yet, to a larger extent for the Ni 3 Ga 1 NPs, which, in turn, feature a higher amount of excess Ni. We reveal that metallic Ni is responsible for the high selectivity of the Ni 3 Ga 1 NPs towards the production of methane in our catalytic tests. In contrast, the Ni 5 Ga 3 NPs display a strong selectivity toward methanol production (>92%), more than one order of magnitude higher than that for the Ni 3 Ga 1 NPs, which we ascribe to the presence of the δ-Ni 5 Ga 3 phase.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Densification, microstructure, and mechanical properties of Mo–30W alloys fabricated from conditioned powders

Refractory alloys, such as molybdenum-based systems, are attracting growing interest for applications in extreme environments, such as in the nuclear and aerospace industries. Recent advances in sintering technologies, coupled with mechanical alloying, have enabled the tailored design of these alloys by leveraging powder characteristics to control final microstructures and mechanical properties. In this study, Mo-30W alloys were fabricated using electric field-assisted sintering (EFAS) from ball-milled powders with and without hydrogen treatment to investigate the influence of surface oxides on material properties and sintering behavior. The results revealed that samples processed from as-ball-milled powder contained a high density of oxides within the microstructure, whereas oxide presence was significantly reduced in samples fabricated from hydrogen-treated powders. Interestingly, the two powder types led to opposite trends in grain size distribution: samples from untreated powders exhibited grain refinement from sample periphery to the center, while samples from hydrogen-treated powders showed grain coarsening toward the center. This behavior is attributed to temperature gradients present during sintering due to electrical percolation pathway differences during Joule heating. The powder surface oxides may have influenced the temperature distribution and grain evolution. Microhardness profiles measured along both axial and thickness directions were consistent with the grain size distribution. Furthermore, oxide films on powder surfaces have delayed densification by hindering particle necking and atomic diffusion during sintering.

36 - MATERIALS SCIENCE↗