Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “OIL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Surface and Airborne Monitoring Technology for Detecting Geologic Leakage in a CO 2 -Enhanced Oil Recovery Pilot, Anadarko Basin, Texas

Surface and airborne gas monitoring programs are becoming an important part of environmental protection in areas favorable for subsurface storage of carbon dioxide. Understanding structural architecture and its effects on the flux of fluids, specifically CO 2 and CH 4 , in the shallow subsurface and atmosphere is helping design and implement next generation monitoring technologies, including unmanned aerial vehicles (UAVs). An important aspect of this research is using subsurface fracture data to inform the design of flight pathways for UAVs in the Farnsworth Oil Unit of the Anadarko Basin. The target zone for CO 2 storage and enhanced oil recovery in the Farnsworth Oil Unit is in the upper Morrow sandstone at subsurface depths greater than 2,000 m. Field study reveals that sandstone and chert in the High Plains Aquifer contain numerous joints that provide crucial insight into aquifer architecture and subsurface flow pathways. Properties of more than 1,700 joints were measured in the field and in high-resolution satellite images. Two distinctive joint systems interpreted as a conjugate pair were identified in the study area. Joint spacing follows a log-normal statistical scaling rule. These fractures appear to be the product of an E-NE regional compressive stress and may have a significant effect on flow in the High Plains Aquifer system. Based on the results of this research, design of UAV flight paths should be oblique to fractures in a way that maximizes the likelihood of CO 2 and CH 4 flux from of systematic joints and cross joints. Detection of leaks either from subsurface seal failures or surface equipment problems is important to insure that stored CO 2 is not being lost to the atmosphere. In the case of surface leaks, costs go up and injection efficiency goes down. Surface leaks are often short term caused by seal leaks, pop off valves, or other equipment failure modes. In either case, CO 2 is released to the atmosphere. This projects primary goal was to explore the use of low cost sensors coupled with the appropriate hardware and software to produce a low cost system capable of detecting both long and short term leaks. In addition, an aerial system was designed to measure the CO 2 and CH 4 distributions above the surface. Both the ground and UAV based systems were designed, tested and deployed in the Farnsworth field.

02 PETROLEUM↗
DOE OSTI2022

Determination of Phenolic Groups in Bio-Oils Using Revised Folin-Ciocalteu Methods: Single Cuvette and Plate Reader. Laboratory Analytical Procedure (LAP), Issue Date: May 12, 2022

Phenol components are ubiquitous in wood-derived bio-oils and biocrudes. Their reaction with other functional groups (e.g., aldehydes) may contribute to the formation of carbonaceous species and the expected thermal instability of pyrolysis oils. During hydrotreating, phenols can be recalcitrant species, requiring higher reaction temperatures than other oxygen-containing functional groups. Phenols are also present in upgraded products and have been shown to lead to catalyst deactivation during hydrotreating. They also are the first oxygenated functional group to re-appear in the upgraded product, signaling catalyst deactivation. This procedure covers the determination of phenolic compounds in fast pyrolysis oils. This Laboratory Analytical Procedure (LAP) includes two methods, the first allowing for shorter analysis time at increased reaction temperature, while the second employs a longer analysis time but at room temperature. Additionally, the use of both a single cuvette and of a plate reader are also presented.

09 BIOMASS FUELS↗
DOE OSTI2016

Application, Deactivation, and Regeneration of Heterogeneous Catalysts in Bio-Oil Upgrading

The massive consumption of fossil fuels and associated environmental issues are leading to an increased interest in alternative resources such as biofuels. The renewable biofuels can be upgraded from bio-oils that are derived from biomass pyrolysis. Catalytic cracking and hydrodeoxygenation (HDO) are two of the most promising bio-oil upgrading processes for biofuel production. Heterogeneous catalysts are essential for upgrading bio-oil into hydrocarbon biofuel. Although advances have been achieved, the deactivation and regeneration of catalysts still remains a challenge. This review focuses on the current progress and challenges of heterogeneous catalyst application, deactivation, and regeneration. The technologies of catalysts deactivation, reduction, and regeneration for improving catalyst activity and stability are discussed. Some suggestions for future research including catalyst mechanism, catalyst development, process integration, and biomass modification for the production of hydrocarbon biofuels are provided.

09 BIOMASS FUELS↗
DOE OSTI2024

Comparison of Sub-Ppm Instrument Response Suggests Higher Detection Limits Could Be Used to Quantify Methane Emissions from Oil and Gas Infrastructure

Quantifying and controlling fugitive methane emissions from oil and gas facilities remains essential for addressing climate goals, but the costs associated with monitoring millions of production sites remain prohibitively expensive. Current thinking, supported by measurement and simple dispersion modelling, assumes single-digit parts-per-million instrumentation is required. To investigate instrument response, the inlets of three trace-methane (sub-ppm) analyzers were collocated on a facility designed to release gas of known composition at known flow rates between 0.4 and 5.2 kg CH 4 h –1 from simulated oil and gas infrastructure. Methane mixing ratios were measured by each instrument at 1 Hertz resolution over nine hours. While mixing ratios reported by a cavity ring-down spectrometer (CRDS)-based instrument were on average 10.0 ppm (range 1.8 to 83 ppm), a mid-infrared laser absorption spectroscopy (MIRA)-based instrument reported short-lived mixing ratios far larger than expected (range 1.8 to 779 ppm) with a similar nine-hour average to the CRDS (10.1 ppm). We suggest the peaks detected by the MIRA are likely caused by a micrometeorological phenomenon, where vortex shedding has resulted in heterogeneous methane plumes which only the MIRA can observe. Further analysis suggests an instrument like the MIRA (an optical-cavity-based instrument with cavity size ≤10 cm3 measuring at ≥2 Hz with air flow rates in the order of ≤0.3 slpm at distances of ≤20 m from the source) but with a higher detection limit (25 ppm) could detect enough of the high-concentration events to generate representative 20 min-average methane mixing ratios. Even though development of a lower-cost, high-precision, high-accuracy instrument with a 25 ppm detection threshold remains a significant problem, this has implications for the use of instrumentation with higher detection thresholds, resulting in the reduction in cost to measure methane emissions and providing a mechanism for the widespread deployment of effective leak detection and repair programs for all oil and gas infrastructure.

03 NATURAL GAS↗
NASA NTRS1994

Yield and seed oil content response of dwarf, rapid-cycling Brassica to nitrogen treatments, planting density, and carbon dioxide enrichment

Effects of N level (15 to 30 mM), time of N increase (14 to 28 days after planting), and planting density (1163 to 2093 plants/m2) were determined for crop yield responses of dwarf, rapid-cycling brassica (Brassica napus L., CrGC 5-2, Genome: ACaacc). Crops were grown in solid-matrix hydroponic systems and under controlled-environment conditions, including nonsupplemented (ambient) or elevated CO2 concentrations (998 +/- 12 micromoles mol-1). The highest seed yield rate obtained (4.4 g m-2 day-1) occurred with the lowest N level (15 mM) applied at the latest treatment time (day 28). In all trials, CO2 enrichment reduced seed yield rate and harvest index by delaying the onset of flowering and senescence and stimulating vegetative shoot growth. The highest shoot biomass accumulation rate (55.5 g m-2 day-1) occurred with the highest N level (30 mM) applied at the earliest time (day 14). Seed oil content was not significantly affected by CO2 enrichment. Maximum seed oil content (30% to 34%, dry weight basis) was obtained using the lowest N level (15 mM) initiated at the latest treatment time (day 28). In general, an increase in seed oil content was accompanied by a decrease in seed protein. Seed carbohydrate, moisture, and ash contents did not vary significantly in response to experimental treatments. Effects of N level and time of N increase were consistently significant for most crop responses. Planting density was significant only under elevated CO2 conditions.

Non-NASA Center↗
NASA NTRS2012

Polarimetric Retrievals of Surface and Cirrus Clouds Properties in the Region Affected by the Deepwater Horizon Oil Spill

In 2010, the Goddard Institute for Space Studies (GISS) Research Scanning Polarimeter (RSP) performed several aerial surveys over the region affected by the oil spill caused by the explosion of the Deepwater Horizon offshore platform. The instrument was deployed on the NASA Langley B200 aircraft together with the High Spectral Resolution Lidar (HSRL), which provides information on the distribution of the aerosol layers beneath the aircraft, including an accurate estimate of aerosol optical depth. This work illustrates the merits of polarization measurements in detecting variations of ocean surface properties linked to the presence of an oil slick. In particular, we make use of the degree of linear polarization in the glint region, which is severely affected by variations in the refractive index but insensitive to the waviness of the water surface. Alterations in the surface optical properties are therefore expected to directly affect the polarization response of the RSP channel at 2264 nm, where both molecular and aerosol scattering are negligible and virtually all of the observed signal is generated via Fresnel reflection at the surface. The glint profile at this wavelength is fitted with a model which can optimally estimate refractive index, wind speed and direction, together with aircraft attitude variations affecting the viewing geometry. The retrieved refractive index markedly increases over oil-contaminated waters, while the apparent wind speed is significantly lower than in adjacent uncontaminated areas, suggesting that the slick dampens high-frequency components of the ocean wave spectrum. The constraint on surface reflectance provided by the short-wave infrared channels is a cornerstone of established procedures to retrieve atmospheric aerosol microphysical parameters based on the inversion of the RSP multispectral measurements. This retrieval, which benefits from the ancillary information provided by the HSRL, was in this specific case hampered by prohibitive variability in atmospheric conditions (very inhomogeneous aerosol distribution and cloud cover). Although the results presented for the surface are essentially unaffected, we discuss the results obtained by typing algorithms in sorting the complex mix of aerosol types, and show evidence of oriented ice in cirrus clouds present in the area. In this context, polarization measurements at 1880 nm were used to infer ice habit and cirrus optical depth, which was found in the subvisual/threshold-visible regime, confirming the utility of the aforementioned RSP channel for the remote sensing of even thin cold clouds.

Polarization↗
NASA NTRS2015

A Decade of Change in NO2 and SO2 over the Canadian Oil Sands As Seen from Space

A decade (20052014) of observations from the Ozone Monitoring Instrument (OMI) were used to examine trends in nitrogen dioxide(NO2) and sulfur dioxide (SO2) over a large region of western Canada and the northern United States, with a focus on the Canadian oil sands. In the oil sands, primarily over an area of intensive surface mining, NO2 tropospheric vertical column densities (VCDs) are seen to be increasing by as much as 10year, with the location of the largest trends in a newly developing NO2 lobe well removed from surface monitoring stations. SO2 VCDs in the oil sands have remained approximately constant. The only other significant increase in the region was seen in NO2 over Bakken gas fields in North Dakota which showed increases of up to5yr. By contrast, other locations in the region show substantial declines in both pollutants, providing strong evidence to the efficacy of environmental pollution control measures implemented by both nations. The OMI-derived trends were found to be consistent with those from the Canadian surface monitoring network, although in the case of SO2, it was necessary to apply a correction in order to remove the residual signal from volcanic eruptions present in the OMI data.

NO2↗
DOE OSTI2014

Formation of carbonaceous nano-layers under high interfacial pressures during lubrication with mineral and bio-based oils

In order to better protect steel surfaces against wear under high loads, understanding of chemical reactions between lubricants and metal at high interfacial pressures and elevated temperatures needs to be improved. Solutions at 5 to 20 wt. % of zinc di-2-ethylhexyl dithio phosphate (ZDDP) and chlorinated paraffins (CP) in inhibited paraffinic mineral oil (IPMO) and inhibited soy bean oil (ISBO) were compared on a Twist Compression Tribotester (TCT) at 200 MPa. Microscopy of wear tracks after 10 seconds tribotesting showed much smoother surface profiles than those of unworn areas. X-ray photoelectron spectroscopy (XPS) coupled with Ar-ion sputtering demonstrated that additive solutions in ISBO formed 2–3 times thicker carbon-containing nano-layers compared to IPMO. The amounts of Cl, S or P were unexpectedly low and detectable only on the top surface with less than 5 nm penetration. CP blends in IPMO formed more inorganic chlorides than those in ISBO. It can be concluded that base oils are primarily responsible for the thickness of carbonaceous nano-layers during early stages of severe boundary lubrication, while CP or ZDDP additive contributions are important, but less significant.

42 ENGINEERING↗
DOE OSTI2015

Development of Nuclear Renewable Oil Shale Systems for Flexible Electricity and Reduced Fossil Fuel Emissions

We propose the development of Nuclear Renewable Oil Shale Systems (NROSS) in northern Europe, China, and the western United States to provide large supplies of flexible, dispatchable, very-low-carbon electricity and fossil fuel production with reduced CO2 emissions. NROSS are a class of large hybrid energy systems in which base-load nuclear reactors provide the primary energy used to produce shale oil from kerogen deposits and simultaneously provide flexible, dispatchable, very-low-carbon electricity to the grid. Kerogen is solid organic matter trapped in sedimentary shale, and large reserves of this resource, called oil shale, are found in northern Europe, China, and the western United States. NROSS couples electricity generation and transportation fuel production in a single operation, reduces lifecycle carbon emissions from the fuel produced, improves revenue for the nuclear plant, and enables a major shift toward a very-low-carbon electricity grid. NROSS will require a significant development effort in the United States, where kerogen resources have never been developed on a large scale. In Europe, however, nuclear plants have been used for process heat delivery (district heating), and kerogen use is familiar in certain countries. Europe, China, and the United States all have the opportunity to use large scale NROSS development to enable major growth in renewable generation and either substantially reduce or eliminate their dependence on foreign fossil fuel supplies, accelerating their transitions to cleaner, more efficient, and more reliable energy systems.

Nuclear Renewable↗
DOE OSTI2022

The Myth of Using Straight Vegetable Oil as a Diesel Fuel

Learn why straight vegetable oil and other waste cooking oils are not the same as biodiesel and why it is important to convert them to biodiesel for use in vehicles and heavy machinery. This fact sheet from Energy Saver includes information on straight vegetable oil performance, its effects on engines, and fuel blends approved for diesel vehicles and engines.

biodiesel, vehicles, straight vegetable oil, fuel ↗
DOE OSTI2022

CO2 Enhanced Oil Recovery Improvement in Conventional Fields Using Rich Gas

Research Hypothesis: The injection of a blend of rich hydrocarbon gas and CO2 into an oil reservoir will reduce molecular weight (MW) selectivity, lower minimum miscibility pressure (MMP) and viscosity of the oil, and improve gas solubility, resulting in an overall improvement in enhanced oil recovery (EOR) performance.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2022

From Petroleum to Biobased Crude: A Thermoplastic Polyurethane from Lignin-Oil Without Isocyanates

The movement to transfer from petroleum-based products and materials to renewables does not necessarily have to bypass the use of oil. A new type of "black-gold" is readily abundant from the earth's most abundant source of aromatic carbon: lignin. While fractionation of petroleum yields fuels and chemicals for a diverse set of industries, lignin fractionation using targeted catalysts has demonstrated the ability to generate monomers and oligomers rich in functional groups for polymer synthesis. This study explores the use of lignin-oil, generated from reductive catalytic fractionation of popular wood, to a hydroxyl-rich mixture of aromatics that is used to synthesize a thermoplastic non-isocyanate polyurethane. The lignin-oil is first converted to a cyclocarbonated derivative using a benign synthetic sequence and further polymerized with a diamine to yield the non-isocyanate TPU. While more work is underway to optimize the reaction conditions and meet typical mechanical properties of commercial materials, initial analysis shows thermoplastic behavior and flexible properties consistent with traditional thermoplastic polyurethanes.

BIOMASS FUELS↗
NASA NTRS1954

Drop Hammer Tests with Three Oleo Strut Models and Three Different Shock Strut Oils at Low Temperatures

Drop hammer tests with different shock strut models and shock strut oils were performed at temperatures ranging to -40 C. The various shock strut models do not differ essentially regarding their springing and damping properties at low temperatures; however, the influence of the different shock strut oils on the springing properties at low temperatures varies greatly.

LUBRICATING OILS, MINERAL↗
DOE OSTI2017

Strategy for Extending the Stability of Bio‐oil‐Derived Phenolic Oligomers by Mild Hydrotreatment with Ionic‐Liquid‐Stabilized Nanoparticles

Abstract The development of catalytic transformations and processes is essential to utilize bio‐oil and lignin derivatives. Metal nanoparticles (M‐NPs) stabilized in ionic liquids (ILs) are promising for the catalytic hydrotreatment of bio‐oil because the properties of the catalyst system can be customized by combining the appropriate IL and metal nanoparticles. Herein, we demonstrate an experimental approach to stabilize lignin‐derived phenolics isolated from bio‐oil with ruthenium NPs stabilized by an ionic copolymer in 1‐ethyl‐3‐methylimidazolium acetate ([C 2 C 1 Im][OAc]). The mild hydrotreatment of phenolic oligomers (POs) was performed with the synthesized M‐NP catalyst at 100 °C for 6 h. Hydrotreatment of the POs resulted in enhanced thermal stability of the POs by as much as a factor of three, as determined by the aging index and by reducing reactive functionalities, which was also confirmed by NMR spectroscopy and GC analysis. The results support our hypothesis that M‐NPs stabilized in ILs can effectively stabilize POs under mild conditions, which could be applicable to any lignin‐derived phenolic.

Kim, Kwang Ho↗
DOE OSTI2018

Catalytic Hydrotreatment of Humins to Bio‐Oil in Methanol over Supported Metal Catalysts

Abstract Valorization of humins, the polymeric byproducts formed during the acid‐catalyzed production of HMF (5‐hydroxymethylfurfural) or furfural, is necessary to improve process economics and make biorefineries viable. We report the one‐step catalytic hydrotreatment of humins in methanol to humin oil containing fully or partially deoxygenated compounds. First, we compare four commercial noble‐metal catalysts (Ru/C, Rh/C, Pt/C, and Pd/C). Aromatic hydrocarbons, phenols, and esters are the main products detected by GC. Rh/C achieves the best GC‐detectable oil yield and 75 % humins conversion in 3 h at 400 °C, 30 bar H 2 , and a catalyst‐to‐humins mass ratio of 1:10. High H 2 pressures and intermediate temperatures, reaction times, and catalyst loadings enhance GC‐detectable oil yields. In contrast, high temperatures and long reaction times enhance gasification. Aromatics and phenols are found at high temperatures and long reaction times, whereas esters are the major species at short reaction times and high catalyst loading. 13 C‐isotopic labeling studies confirm, for the first time, that methanol participates in the alkylation and esterification reactions to form aromatic, phenolic and ester products. The reactivity in isopropanol is also discussed.

Cheng, Ziwei↗
DOE OSTI2015

Energetics Applications for the Oil and Gas Industry

Here, early motivation and use of energetic materials in the Western World by Alfred Nobel was intended to facilitate mining, construction, and demolition activities. The motivation for the work was the recognized need for a safer energetic material as an alternate to unstabilized nitroglycerine. The invention of dynamite by Nobel was widely adopted in the civilian world and brought a fortune to Nobel, resulting in the formation of the annual Nobel Prize awards, recognizing significant achievements across many fields of endeavour. Nonetheless, further development of energetics was primarily motivated by and funded for military purposes, rather than civilian usage. And indeed much investment has been given to the development and characterization of military energetics and their application. An example application is the precision shaped charge, primarily developed as a means of focusing energy in a narrow metallic jet for deep penetration of heavy armor. However, the largest costumer today and for many years for shaped charges is not the military, but rather the oil and gas industry, which has adapted the military technology for perforation of oil and gas wells. While there are similar aspects to desired penetration capabilities in both applications, there are enough differences to warrant energetics R & D focused on oil and gas industry needs.

02 PETROLEUM↗
DOE OSTI2015

CT-guided Irreversible Electroporation in an Acute Porcine Liver Model: Effect of Previous Transarterial Iodized Oil Tissue Marking on Technical Parameters, 3D Computed Tomographic Rendering of the Electroporation Zone, and Histopathology

PurposeTo evaluate the effect of previous transarterial iodized oil tissue marking (ITM) on technical parameters, three-dimensional (3D) computed tomographic (CT) rendering of the electroporation zone, and histopathology after CT-guided irreversible electroporation (IRE) in an acute porcine liver model as a potential strategy to improve IRE performance.MethodsAfter Ethics Committee approval was obtained, in five landrace pigs, two IREs of the right and left liver (RL and LL) were performed under CT guidance with identical electroporation parameters. Before IRE, transarterial marking of the LL was performed with iodized oil. Nonenhanced and contrast-enhanced CT examinations followed. One hour after IRE, animals were killed and livers collected. Mean resulting voltage and amperage during IRE were assessed. For 3D CT rendering of the electroporation zone, parameters for size and shape were analyzed. Quantitative data were compared by the Mann–Whitney test. Histopathological differences were assessed.ResultsMean resulting voltage and amperage were 2,545.3 ± 66.0 V and 26.1 ± 1.8 A for RL, and 2,537.3 ± 69.0 V and 27.7 ± 1.8 A for LL without significant differences. Short axis, volume, and sphericity index were 16.5 ± 4.4 mm, 8.6 ± 3.2 cm{sup 3}, and 1.7 ± 0.3 for RL, and 18.2 ± 3.4 mm, 9.8 ± 3.8 cm{sup 3}, and 1.7 ± 0.3 for LL without significant differences. For RL and LL, the electroporation zone consisted of severely widened hepatic sinusoids containing erythrocytes and showed homogeneous apoptosis. For LL, iodized oil could be detected in the center and at the rim of the electroporation zone.ConclusionThere is no adverse effect of previous ITM on technical parameters, 3D CT rendering of the electroporation zone, and histopathology after CT-guided IRE of the liver.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2018

Preparation and Property Research of Perfluoropolyether Oil-Based Ferrofluid

In this study, perfluoropolyether oil-based ferrofluid was prepared to satisfy special demands in applications which are too harsh to conventional ferrofluids. Fe{sub 3}O{sub 4} magnetic nanoparticles were synthesized by co-precipitation and modified by perfluoropolyether carboxylic acid surfactant in the atmosphere without protective gas. Perfluoropolyether oil-based ferrofluid was prepared with modified nanoparticles and perfluoropolyether by high-energy ball milling. Properties of ferrofluid fabricated were verified through a series of experiments. Ferrofluid stability was tested by interval point-density method; the average density change is merely 0.0077 g/ml, and change rate is 0.37% after 500 days. Saturation magnetization is 582.46 Gs, much larger than the other four ferrofluids. The average volatility rate is 7.4985*10{sup − 5} g/h/cm{sup 2} at 80 °C after 260 h. Viscosity increases to 1825.7 mPa⋅ s under − 20 °C and still have mobility at − 40 °C. The ferrofluid can resist air blast for 8 h under 200 °C without oxidation or decomposition. Perfluoropolyether oil-based ferrofluid cannot be damaged by water or organic solvents. In addition, the ferrofluid can survive in pH = 1 acid or pH = 14 alkali at least 279 days without corrosion.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗