SEARCH · Engineering Papers

Results for “Nuclear Engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

All sources NASA NTRS DOE OSTI

NASA NTRS1957

Experimental Investigation of Vibratory Stresses in a Concentric-Ring Direct-Air-Cycle Nuclear Fuel Element

Preliminary tests made by the General Electric Company indicated that aerodynamic loads might cause large enough distortions in the thin sheet-metal rings of a nuclear fuel element to result in structural failure. The magnitude of the distortions in a test fuel element was determined from strains measured with airflow conditions simulating those expected during engine operation. The measured vibratory strains were low enough to indicate the improbability of failure by fatigue. A conservative estimate of the radial deflection that accompanied peak strains in the outer ring was +0.0006 inch.

Chiarito, Patrick T.↗

NASA NTRS2016

Stirling to Flight Initiative

NASA has a consistent need for radioisotope power systems (RPS) to enable robotic scientific missions for planetary exploration that has been present for over four decades and will continue into the foreseeable future, as documented in the most recent Planetary Science Decadal Study Report. As RPS have evolved throughout the years, there has also grown a desire for more efficient power systems, allowing NASA to serve as good stewards of the limited plutonium-238 (238Pu), while also supporting the ever-present need to minimize mass and potential impacts to the desired science measurements. In fact, the recent Nuclear Power Assessment Study (NPAS) released in April 2015 resulted in several key conclusion regarding RPS, including affirmation that RPS will be necessary well into the 2030s (at least) and that 238Pu is indeed a precious resource requiring efficient utilization and preservation. Stirling Radioisotope Generators (SRGs) combine a Stirling cycle engine powered by a radioisotope heater unit into a single generator system. Stirling engine technology has been under development at NASA Glenn Research Center (GRC) in partnership with the Department of Energy (DOE) since the 1970's. The most recent design, the 238Pu-fueled Advanced Stirling Radioisotope Generator (ASRG), was offered as part of the NASA Discovery 2010 Announcement of Opportunity (AO). The Step-2 selections for this AO included two ASRG-enabled concepts, the Titan Mare Explorer (TiME) and the Comet Hopper (CHopper), although the only non-nuclear concept, InSight, was ultimately chosen. The DOE's ASRG contract was terminated in 2013. Given that SRGs utilize significantly less 238Pu than traditional Radioisotope Thermoelectric Generators (RTGs) - approximately one quarter of the nuclear fuel, to produce similar electrical power output - they provide a technology worthy of consideration for meeting the aforementioned NASA objectives. NASA's RPS Program Office has recently investigated a new Stirling to Flight (S2F) initiative with the objective of developing a 100-500 We Stirling generator system. Additionally, a different approach is being devised for this initiative to avoid pitfalls of the past, and apply lessons learned from the recent ASRG experience. Two key aspects of this initiative are a Stirling System Technology Maturation Effort, and a Surrogate Mission Team (SMT) intended to provide clear mission pull and requirements context. The S2F project seeks to lead directly into a DOE flight system development of a new SRG. This paper will detail the proposed S2F initiative, and provide specifics on the key efforts designed to pave a forward path for bringing Stirling technology to flight.

Robotics↗

NASA NTRS1980

A prelude to interstellar flight

A 20 to 50 year interstellar precursor mission extending 400 to 1000 AU from the solar system is outlined as a means of bringing out and solving engineering problems inherent in a star mission, and of studying the heliopause, the interstellar medium, and cosmic rays outside the heliosphere. Solar or laser sailing combined with a 500 kWe nuclear-electric propulsion system using fission would achieve a heliocentric excess velocity of 100km/s for the 32,000 kg spacecraft having a Shuttle derivative as a launch vehicle, and containing a Pluto flyby or separate orbiter powered by radioiosotope thermoelectric generators. X-band transmission using 40 w of power, a 15 m diameter spacecraft antenna and a 100 m receiving antenna on earth and providing 100 b/s is proposed, but a rate of 2 to 4 kb/s via 500 to 1000 w of power using the K-band and a 300 m diameter receiving antenna located on an Orbiting Deep Space Relay Station is also considered.

Jaffe, L. D.↗

NASA NTRS1994

Study of activation data of metal samples from LDEF-1 and Spacelab-2

Gamma-ray spectra obtained from samples flown aboard the Long Duration Exposure Facility have been analyzed to obtain the nuclear species produced in this material by the interaction of this material with protons and neutrons in this material by the interaction of this material with protons and neutrons encountered in its 69 month orbital flight as well as to quantify the specific activity (pCi/kg) of these nuclear species. This quantification requires accurate corrections of efficiency, self-attenuation, and background. Plans have been developed for archival of the spectra in a form readily accessible to the scientific, engineering and technical community engaged in space research and application. Work has been initiated in the process of estimating the flux of activating particles encountered by material at various locations of the spacecraft.

Laird, C. E.↗

NASA NTRSDate not supplied

Key Performance Parameters for an Operational CIS-Lunar NTP Vehicle

Nuclear Thermal Propulsion (NTP) is in active development by NASA and DARPA. This paper presents an investigation into the effects of different values of key performance parameters (KPPs) of an NTP engine in the context of payload delivery missions between Earth and Lunar orbits. The high Isp afforded by NTP combined with the relatively large engine mass is best applied to missions where the payload mass is large and required ΔV high. Two missions considered are the round-trip Earth to Moon tug and a NRHO to low Lunar orbit tug. Chemical propulsion vehicles can generally achieve higher propellant mass fractions, similar payload mass and similar ΔV performance on these missions. When re-use of the vehicle is considered, the reduced propellant mass required by an NTP vehicle begins to add up over multiple refilling launches and trades more favorably. Analysis illustrates the impact of variation in NTP engine performance values, especially Isp, engine mass and thrust, on performance and the comparison to chemical propulsion. NTP transient and cooldown effects on the vehicle performance are examined. A variety of launch vehicles and hydrogen and ammonia NTP propellants are included in the analyses, and cryogenic fluid management system effects are accounted for.

NTP↗

NASA NTRS1999

Initial Test Firing Results for Solid CO/GOX Cryogenic Hybrid Rocket Engine for Mars ISRU Propulsion Applications

ORBITEC is developing methods for producing, testing, and utilizing Mars-based ISRU fuel/oxidizer combinations to support low cost, planetary surface and flight propulsion and power systems. When humans explore Mars we will need to use in situ resources that are available, such as: energy (solar); gases or liquids for life support, ground transportation, and flight to and from other surface locations and Earth; and materials for shielding and building habitats and infrastructure. Probably the easiest use of Martian resources to reduce the cost of human exploration activities is the use of the carbon and oxygen readily available from the CO2 in the Mars atmosphere. ORBITEC has conducted preliminary R&D that will eventually allow us to reliably use these resources. ORBITEC is focusing on the innovative use of solid CO as a fuel. A new advanced cryogenic hybrid rocket propulsion system is suggested that will offer advantages over LCO/LOX propulsion, making it the best option for a Mars sample return vehicle and other flight vehicles. This technology could also greatly support logistics and base operations by providing a reliable and simple way to store solar or nuclear generated energy in the form of chemical energy that can be used for ground transportation (rovers/land vehicles) and planetary surface power generators. This paper describes the overall concept and the test results of the first ever solid carbon monoxide/oxygen rocket engine firing.

Rice, Eric E.↗

NASA NTRS2005

The Spaceflight Revolution Revisited

This essay will first consider whether technological breakthroughs in space technology and the rational motives of ordinary institutions have the capacity to break out of this relatively static situation. Then we will survey the roles that social movements of various kinds might play and conclude with an examination of one particular nascent movement that might possibly build the foundation for a spacefaring civilization. A third of a century ago, practical nuclear fission rockets were under development, but this approach now seems environmentally unacceptable. It is hard to devise a more environmentally benign propellant than the hydrogen and oxygen used by the main engines of the Space Shuttle. There is some hope that nanotechnology will save the day with materials based on carbon nanotubes that are vastly stronger yet lighter than metals.6 However, the X-33 failure shows that it is not easy to work with radically new structural materials in demanding aerospace applications, and we may be many decades away from being able to manufacture propellant tanks, wings, and other large structures from carbon nanotubes. Satellites in low-Earth and synchronous orbit are of great importance in the collection and distribution of information, thus essential to the information economy. The wide range of civilian applications includes telephone, data transmission, television, navigation, weather observation, agriculture monitoring, and prospecting for natural resources.8 The technology is largely perfected, and incremental progress can be achieved by improvement in information systems and simply by investing in more relatively small satellites of the kinds we already have.

Bainbridge, William Sims↗

NASA NTRS1994

Multiwavelength tests of the dusty torus model for Seyfert galaxies

We present a compilation of emission properties for a sample of 116 Seyfert galaxies based on both previously unpublished data and measurements available in the literature. These measurements include fluxes in the emission lines (O III) lambda(5007) and H-beta, as well as the infrared (25-60 microns), ultraviolet (1450 A), soft (0.2-4 keV), and hard (2-10 keV) X-ray continua. These are used to try to distinguish between isotropic and anisotropic emission properties of Seyfert galaxies. The distribution functions of (O III) lambda 5007 infrared, and hard X-ray continuum are similar for Seyfert 1's and Seyfert 2's, consistent with these properties being isotropic. The ultraviolet and soft X-ray continua of Seyfert 2's are underluminous relative to the type 1's suggesting photons at these energies escape from the central source anisotropically. There is a correlation between the ultraviolet continuum and emission-line fluxes in Seyfert 1's consistent with the idea that the central engine is responsible for powering the line emission. No such correlation is found for the Seyfert 2's. Instead, the scatter in the plot of ultraviolet continuum versus line emission suggests the true nuclear continuum luminosity is not seen at Earth in these objects. These properties are consistent with those expected in the dusty torus model.

Mulchaey, John S.↗

NASA NTRS2004

Extraction of Oxygen from the Martian Atmosphere

A mechanical process was designed for direct extraction of molecular oxygen from the martian atmosphere based on liquefaction of the majority component, CO2, followed by separation of the lower-boiling components. The atmospheric gases are compressed from about 0.007 bar to 13 bar and then cooled to liquefy most of the CO2. The uncondensed gases are further compressed to 30 bar or more, and then cooled again to recover water as ice and to remove much of the remaining CO2. The final gaseous products consisting mostly of nitrogen, oxygen, and carbon monoxide are liquefied and purified by cryogenic distillation. The liquefied CO2 is expanded back to the low-pressure atmosphere with the addition of heat to recover a majority of the compression energy and to produce the needed mechanical work. Energy for the process is needed primarily as heat to drive the CO2-based expansion power system. When properly configured, the extraction process can be a net producer of electricity. The conceptual design, termed 'MARRS' for Mars Atmosphere Resource Recovery System, was based on the NASA/JSC Mars Reference Mission (MRM) requirement for oxygen. This mission requires both liquid oxygen for propellant, and gaseous oxygen as a component of air for the mission crew. With single redundancy both for propellant and crew air, the oxygen requirement for the MRM is estimated at 5.8 kg/hr. The process thermal power needed is about 120 kW, which can be provided at 300-500 C. A lower-cost nuclear reactor made largely of stainless steel could serve as the heat source. The chief development needed for MARRS is an efficient atmospheric compression technology, all other steps being derived from conventional chemical engineering separations. The conceptual design describes an exceptionally low-mass compression system that can be made from ultra-lightweight and deployable structures. This system adapts to the rapidly changing martian environment to supply the atmospheric resource to MARRS at constant conditions.

England, C.↗

NASA NTRS2005

CFD Multiphysics Tool

The recent bold initiatives to expand the human presence in space require innovative approaches to the design of propulsion systems whose underlying technology is not yet mature. The space propulsion community has identified a number of candidate concepts. A short list includes solar sails, high-energy-density chemical propellants, electric and electromagnetic accelerators, solar-thermal and nuclear-thermal expanders. For each of these, the underlying physics are relatively well understood. One could easily cite authoritative texts, addressing both the governing equations, and practical solution methods for, e.g. electromagnetic fields, heat transfer, radiation, thermophysics, structural dynamics, particulate kinematics, nuclear energy, power conversion, and fluid dynamics. One could also easily cite scholarly works in which complete equation sets for any one of these physical processes have been accurately solved relative to complex engineered systems. The Advanced Concepts and Analysis Office (ACAO), Space Transportation Directorate, NASA Marshall Space Flight Center, has recently released the first alpha version of a set of computer utilities for performing the applicable physical analyses relative to candidate deep-space propulsion systems such as those listed above. PARSEC, Preliminary Analysis of Revolutionary in-Space Engineering Concepts, enables rapid iterative calculations using several physics tools developed in-house. A complete cycle of the entire tool set takes about twenty minutes. PARSEC is a level-zero/level-one design tool. For PARSEC s proof-of-concept, and preliminary design decision-making, assumptions that significantly simplify the governing equation sets are necessary. To proceed to level-two, one wishes to retain modeling of the underlying physics as close as practical to known applicable first principles. This report describes results of collaboration between ACAO, and Embry-Riddle Aeronautical University (ERAU), to begin building a set of level-two design tools for PARSEC. The "CFD Multiphysics Tool" will be the propulsive element of the tool set. The name acknowledges that space propulsion performance assessment is primarily a fluid mechanics problem. At the core of the CFD Multiphysics Tool is an open-source CFD code, HYP, under development at ERAU. ERAU is renowned for its undergraduate degree program in Aerospace Engineering the largest in the nation. The strength of the program is its applications-oriented curriculum, which culminates in one of three two-course Engineering Design sequences: Aerospace Propulsion, Spacecraft, or Aircraft. This same philosophy applies to the HYP Project, albeit with fluid physics modeling commensurate with graduate research. HYP s purpose, like the Multiphysics Tool s, is to enable calculations of real (three-dimensional; geometrically complex; intended for hardware development) applications of high speed and propulsive fluid flows.

Perrell, Eric R.↗

NASA NTRSDate not supplied

Advanced Materials for the Lunar Surface: Multiscale Computational Design of Refractory Alloys and Carbides

Emerging operational environments, such as the lunar surface, present novel challenges for NASA and drive the need for advanced materials in applications like fission surface power systems. To address these demands, computational materials science is rapidly evolving to augment or replace costly and hazardous empirical testing. Although materials selection at NASA remains predominantly experimentally driven, advanced simulation methodologies are being steadily integrated into the engineering lifecycle. This work details the application of multiscale simulation techniques—including first-principles calculations, CALPHAD, dislocation dynamics, and molecular dynamics—at NASA's Ames Research Center to evaluate advanced materials for extreme environments. First, we present contributions to the Space Nuclear Propulsion Project. Be-cause propellant channel coatings in nuclear thermal rockets must withstand high-pressure, high-temperature hydro-gen, optimizing these materials is critical. First-principles calculations were employed to establish a rigorous quantitative and qualitative understanding of the behavior of the refractory carbides ZrC, NbC, and their mixtures in high-enthalpy hydrogen environments. This necessitated the generation of high-fidelity thermodynamic models for both stoichiometric and carbon-depleted carbides, both with and without the presence of hydrogen. Furthermore, we highlight efforts under the Refractory Alloy Additive Manufacturing Build Optimization (RAAMBO) project, where existing and novel alloy compositions were assessed for additive manufacturing printability and subsequent performance in applications such as heat pipes and rocket nozzle extensions. This was accomplished through a comprehensive multiscale simulation framework that bridged the gap from the nanometer to the millimeter scale. Across both initiatives, rigorous validation against empirical data was prioritized. By systematically employing a verified and validated computational frame-work, we demonstrate how simulation effectively supports multidisciplinary engineering efforts, builds project-wide confidence, and drives critical materials development.

computational materials↗

NASA NTRSDate not supplied

Nuclear Thermal Propulsion (NTP) Fission Product and Source Term Analysis

Nuclear thermal propulsion (NTP) is an in-space propulsion technology that uses a nuclear reactor to directly heat a propellant to provide high thrust, at higher efficiencies than achievable with conventional chemical propulsion systems. Due to the ability of NTP rockets to efficiently provide high thrust, this technology has been proposed for long duration space missions such as crewed missions to Mars and beyond. A primary hurdle for NTP technology development is the demonstration of an integrated reactor engine system to verify its functionality and performance. This primarily requires the manufacture and testing of candidate reactor and engine technologies to demonstrate the proposed design enables desired performance and exhibits acceptable response under all known operation modes. A major component in this testing is fission product accumulation, since after operation radioactive isotopes can be produced and pose radiological dose concerns. This paper explains the background behind fission product analysis and the methodology used to evaluate current reactor designs and identify the amount of fission products present and their radiological impact. Results of multiple thrust level engines at different time periods are discussed and highlight the need for additional experimental testing to confirm fractional release levels of fission products out of the system. Benchmarking of models and future paths of analysis are also discussed.

Nuclear Thermal Propulsion↗

NASA NTRS1993

JPL nuclear electric propulsion task

The development of lithium magnetoplasmadynamic (MPD) thrusters at JPL is discussed. The following topics are presented in vugraph form: mercury vapor mass flow control; porous tungsten vaporizer and housing; the lithium vaporizer experiment; a dry box for handling solid lithium; MPD thruster electrode modeling; engine lifetime definitions; cathode failure modeling; cathode erosion modeling; cathode thermal modeling; near cathode plasma model regions; cathode work function modeling; anode work function modeling; and radiation-cooled anodes.

Pivirotto, Tom↗

NASA NTRS2001

Space Fission Propulsion System Development Status

The world's first man-made self-sustaining fission reaction was achieved in 1942. Since then fission has been used to propel submarines, generate tremendous amounts of electricity, produce medical isotopes, and provide numerous other benefits to society. Fission systems operate independently of solar proximity or orientation, and are thus well suited for deep space or planetary surface missions. In addition, the fuel for fission systems (enriched uranium) is virtually non-radioactive. The primary safety issue with fission systems is avoiding inadvertent system start. Addressing this issue through proper system design is straight-forward. Despite the relative simplicity and tremendous potential of space fission systems, the development and utilization of these systems has proven elusive. The first use of fission technology in space occurred 3 April 1965 with the US launch of the SNAP-10A reactor. There have been no additional US uses of space fission systems. While space fission systems were used extensively by the former Soviet Union, their application was limited to earth-orbital missions. Early space fission systems must be safely and affordably utilized if we are to reap the benefits of advanced space fission systems. NASA's Marshall Space Flight Center, working with Los Alamos National Laboratory (LANL), Sandia National Laboratories, and others, has conducted preliminary research related to a Safe Affordable Fission Engine (SAFE). An unfueled core has been fabricated by LANL, and resistance heaters used to verify predicted core thermal performance by closely mimicking heat from fission. The core is designed to use only established nuclear technology and be highly testable. In FY01 an energy conversion system and thruster will be coupled to the core, resulting in an 'end-to-end' nuclear electric propulsion demonstrator being tested using resistance heaters to closely mimic heat from fission. Results of the SAFE test program will be presented. The applicability of a SAFE-powered electric propulsion system to outer planet science missions will also be discussed.

Houts, M.↗

NASA NTRSDate not supplied

Heat Pipe Development For Space Fission Demonstration Missions

NASA is currently formulating a flight mission that will demonstrate a 10 kWe nuclear electric fission power system for use on the lunar surface. While preliminary mission concepts leverage the successful Kilopower Reactor Using Stirling Technology ground prototype demonstration of a 1 kWe reactor, there are significant engineering challenges associated with adapting that prototype reactor for flight. One of these challenges is to modify the high temperature sodium heat pipes for use in space operation. Ongoing technical work at the NASA Glenn Research Center seeks to address several key areas of heat pipe development, focusing on fluid return under reduced or microgravity conditions and improved interfaces for both the reactor and the power conversion ends of the heat pipe.

Fission↗

NASA NTRSDate not supplied

Nuclear Thermal Propulsion (NTP) Fission Product and Source Term Analysis

Fission↗

NASA NTRS1986

Optics in engineering measurement; Proceedings of the Meeting, Cannes, France, December 3-6, 1985

The present conference on optical measurement systems considers topics in the fields of holographic interferometry, speckle techniques, moire fringe and grating methods, optical surface gaging, laser- and fiber-optics-based measurement systems, and optics for engineering data evaluation. Specific attention is given to holographic NDE for aerospace composites, holographic interferometry of rotating components, new developments in computer-aided holography, electronic speckle pattern interferometry, mass transfer measurements using projected fringes, nuclear reactor photogrammetric inspection, a laser Doppler vibrometer, and optoelectronic measurements of the yaw angle of projectiles.

Fagan, William F.↗

NASA NTRS2009

Johnson Space Center's Risk and Reliability Analysis Group 2008 Annual Report

The Johnson Space Center (JSC) Safety & Mission Assurance (S&MA) Directorate s Risk and Reliability Analysis Group provides both mathematical and engineering analysis expertise in the areas of Probabilistic Risk Assessment (PRA), Reliability and Maintainability (R&M) analysis, and data collection and analysis. The fundamental goal of this group is to provide National Aeronautics and Space Administration (NASA) decisionmakers with the necessary information to make informed decisions when evaluating personnel, flight hardware, and public safety concerns associated with current operating systems as well as with any future systems. The Analysis Group includes a staff of statistical and reliability experts with valuable backgrounds in the statistical, reliability, and engineering fields. This group includes JSC S&MA Analysis Branch personnel as well as S&MA support services contractors, such as Science Applications International Corporation (SAIC) and SoHaR. The Analysis Group s experience base includes nuclear power (both commercial and navy), manufacturing, Department of Defense, chemical, and shipping industries, as well as significant aerospace experience specifically in the Shuttle, International Space Station (ISS), and Constellation Programs. The Analysis Group partners with project and program offices, other NASA centers, NASA contractors, and universities to provide additional resources or information to the group when performing various analysis tasks. The JSC S&MA Analysis Group is recognized as a leader in risk and reliability analysis within the NASA community. Therefore, the Analysis Group is in high demand to help the Space Shuttle Program (SSP) continue to fly safely, assist in designing the next generation spacecraft for the Constellation Program (CxP), and promote advanced analytical techniques. The Analysis Section s tasks include teaching classes and instituting personnel qualification processes to enhance the professional abilities of our analysts as well as performing major probabilistic assessments used to support flight rationale and help establish program requirements. During 2008, the Analysis Group performed more than 70 assessments. Although all these assessments were important, some were instrumental in the decisionmaking processes for the Shuttle and Constellation Programs. Two of the more significant tasks were the Space Transportation System (STS)-122 Low Level Cutoff PRA for the SSP and the Orion Pad Abort One (PA-1) PRA for the CxP. These two activities, along with the numerous other tasks the Analysis Group performed in 2008, are summarized in this report. This report also highlights several ongoing and upcoming efforts to provide crucial statistical and probabilistic assessments, such as the Extravehicular Activity (EVA) PRA for the Hubble Space Telescope service mission and the first fully integrated PRAs for the CxP's Lunar Sortie and ISS missions.

Valentine, Mark↗