Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Effect of Chromium Content on Microstructure, Hardness, and Wear Resistance of As-Cast Fe-Cr-B Alloy

The effects of chromium content on microstructure, hardness and wear resistance of as-cast Fe-xCr-1.0B (x = 0, 4, 8, 12, 16, 20) alloys were investigated by means of optical microscope (OM), scanning electron microscope (SEM), x-ray diffractometer (XRD), hardness tester and ring block wear tester. The results showed that the microstructures of chromium-free alloy were mainly composed of pearlite, ferrite, and eutectic borocarbides, and the hardness was very low, only 18.8 HRC. With the increase in chromium content, the matrix of as-cast Fe-Cr-B alloy gradually began to transform from pearlite and ferrite to lath martensite, and the type of borocarbides changed from Fe{sub 2}(B, C) to M{sub 2}(B, C), M{sub 7}(C, B){sub 3} and M{sub 23}(C, B){sub 6} (M = Fe, Cr). When the chromium content was 12 wt.%, the hardness of alloy reached the highest value of 61.1 HRC, and the wear resistance of alloy was the best. The results of worn surface analysis showed that the wear failure of as-cast Fe-Cr-B alloy was mainly caused by multiple plastic deformation and micro-cutting.

36 MATERIALS SCIENCE↗
DOE OSTI2019

On the Microstructure and Solidification Behavior of N-Bearing Ti-46Al-8Ta (at.%) Intermetallic Alloys

Ti-46Al-8Ta (at.%) intermetallic alloys exhibit acceptable strength at low and high temperatures with good oxidation resistance. Different alloying elements are usually added to TiAl-based alloys to develop required properties. In this work, effects of N addition up to 2 at.% on microstructural features and solidification behavior of the Ti-46Al-8Ta alloy is investigated. The achieved results showed that alloying with N causes dendrite refinement and reduction of the retained metastable B2 phase in the as-cast microstructure. The dendrite morphology is also changed from fourfold to fivefold and then sixfold symmetry by increasing N content. The effect of N on interlamellar spacing, amount of constituent phases, and lattice parameters was not uniform. Increasing N content resulted in an increase in both small punch maximum load and hardness up to 1.05 at.%, whereas further N alloying, despite increasing of hardness, led to a drop in the maximum load.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Multiscale Modeling of Microstructural Evolution in Fused-Coating Additive Manufacturing

A quantitative phase field model with adaptive-computational-domain-expansion (ACDE) method was developed to simulate the microstructural evolution in fused-coating additive manufacturing process. A heat transfer and fluid flow model was established to investigate the solidification behavior of the molten pool in a single deposited layer. The solidification parameters such as temperature gradient and solidification rate were calculated from the macroscopic model and then fed into the phase field model to get the microstructure at different positions within a single deposited layer. Columnar dendrites were formed at the bottom of the deposited layer, and equiaxed dendrites appeared in the upper part of the layer. The ACDE method is used to improve the simulation efficiency. The metallographic experiments and energy-dispersive spectrometer analysis for composition were conducted on the fused-coating specimen, and the results were in good accordance with the simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Solutionizing Time on Improving the Microstructure and Mechanical Properties of Aged AZ80 Mg Alloy

The effects of solutionizing soak time and aging on the microstructure and mechanical properties of cast AZ80 Mg alloy were investigated. Optical microscopy, scanning electron microscopy and x-ray diffraction revealed the dissolution of β-Mg{sub 17}Al{sub 12} phase in the solution-treated samples which was later detected in the aged condition. Solution treatments at 420 °C for 4-16 h with water quenching followed by aging at 200 °C for 10 h were carried out, causing discontinuous precipitates to be formed with different precipitate morphologies at the various soak times. The discontinuous precipitates were observed to transform from the interdendritic segregation to parallel lamellae with increasing soak time to 8-10 h. As the soak time increased to 16 h, parallel lamellae transformed into tree-like precipitate morphology. The results showed significant changes in the interlamellar spacing at different soak times, and such precipitate morphology could influence the microstructure and mechanical properties after the aging process. A good combination of strength and ductility was obtained when the cast AZ80 Mg alloy was solution-treated at 420 °C for 10 h and aged at 200 °C for 10 h. Compared to the as-cast condition, a significant increase in ultimate tensile strength (50%), yield strength (47%) and elongation (43%) were observed.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and Mechanical Properties of Ni-based Superalloy K418 Produced by the Continuous Unidirectional Solidification Process

Adopting effective strategies to control the solidification structure of Ni-based superalloys is a very interesting subject for metallurgists. Despite the achievement of developing and applying the continuous unidirectional solidification process in simple alloys, the utilization of this process for K418 alloys has been ignored. The microstructure and mechanical properties of a K418 alloy ingot produced by the continuous unidirectional solidification process were investigated. We found that the γ dendrites were typically cross-shaped in the transverse section. The orientation of surviving grains along the casting direction was <001> during competitive growth. The secondary dendrite arm spacing was 32.3 ± 2.5 μm at a cooling rate of 1.75 ± 0.35 °C/s from the surface to the center of the K418 alloy ingot. Due to the higher cooling rate than that of the conventional casting process, a more uniform microstructure and finer γ′ precipitation were obtained in the ingot. Thus, compared with the conventional casting, the tensile strength and the elongation are increased by 8.4 and 21.3%, respectively, at 25 °C. The tensile strength and elongation increased by 15.2 and 49.3%, respectively, at 800 °C. In addition, the fracture surfaces exhibited numerous typical dimples and dendritic fracture characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Microstructure of X-120 Steel on CO{sub 2} Corrosion Inhibition by 2-Mercaptobenzimidazole

The use of 2-mercaptobenzimidazole (2MBI) as corrosion inhibitor for API X-120 pipeline with two different microstructures in a CO{sub 2}-saturated 3.5% NaCl solution has been investigated. One microstructure was predominantly martensitic and bainitic (steel A), whereas the second one was mainly ferritic (steel B). It was found that 2MBI behaved as a mixed type of corrosion inhibitor and it changed the corrosion-controlled mechanism. In the uninhibited solution, steel A had a dissolution rate higher than steel B. However, in the presence of inhibitor, dissolution rate for steel A was lower than that for B because the film-formed inhibitor is adsorbed in a better way for steel A which has smaller precipitates distributed in a more homogeneous way than that for steel B.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Solution Treatment on the Microstructure, Micromechanical Properties, and Kinetic Parameters of the β → α Phase Transformation during Continuous Cooling of Ti-6Al-4V Titanium Alloy

The aim of this study is to examine the effect of solution treatment temperature (STT) on the microstructure, the micromechanical properties, and the kinetic parameters of the β → α phase transformation during continuous cooling of the dual phase titanium alloy Ti-6Al-4V. Increasing the STT from 1050 to 1200 °C delays the formation of the α phase during cooling and increases the value of its activation energy. The microstructural analysis reveals the emergence of α{sub W} platelets from protuberances on the α{sub GB}/α{sub W} interface. The investigation of the morphology of the α{sub W} platelets reveals the presence of ledges on their longest side showing a sharp extremity. The micromechanical properties determined by nanoindentation and microhardness tests are almost insensitive to the cooling rate but are strongly affected by the STT; the higher the STT, the lower the overall microhardness of the Ti-6Al-4V alloy. In addition, the STT affects the microhardness and the Young’s modulus of both α and β phases differently; when the STT increases, the microhardness and the Young’s modulus of the α phase decrease, whereas those of the β phase increases.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Influence of the Composition on the Solidification Path, Microstructure Evolution and Mechanical Properties of Al-Cu-Mg Alloys

The influence of the initial composition on the solidification path, microstructure evolution, thermophysical properties and mechanical properties of Al-Cu-Mg alloys was investigated. The solidification paths of the investigated alloys were determined by analyzing the solidification structure, and then the experimentally determined paths were compared with those from the calculated results. Three of the investigated alloys experienced typical ternary eutectic solidification, and the other four alloys experienced quasiperitectic reactions. Due to differences in the initial compositions, different eutectic morphologies were formed during the solidification process. The binary eutectic phases, (α-Al + Al{sub 2}Cu) and (α-Al + Al{sub 6}CuMg{sub 4}), and the (α-Al + Al{sub 6}CuMg{sub 4} + Al{sub 8}Mg{sub 5}) ternary eutectic phase tended to exhibit divorced growth, and the (α-Al + Al{sub 2}CuMg), (α-Al + Al{sub 6}CuMg{sub 4}) and (α-Al + Al{sub 2}Cu + Al{sub 2}CuMg) eutectic phases tended to exhibit coupled growth. The results indicated that the initial composition, solidification path, microstructure and morphology could greatly affect the melting enthalpy, microhardness and compressive strength of the investigated Al-Cu-Mg alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2019

A Comparative Analysis on Microstructure and Fracture Mechanism of X100 Pipeline Steel CGHAZ Between Laser Welding and Arc Welding

The objective of this study is to compare and contrast the differences in microstructure and fracture mechanism between CGHAZ of laser welding and submerged arc welding in X100 pipeline steel. The single-pass welding thermal simulation test of laser welding and submerged arc welding was carried out in MMS-200 thermal simulation test machine using self-made fixtures. The results indicated that the microstructure of laser welding CGHAZ and submerged arc welding CGHAZ was lath martensite and granular bainite, respectively. The impact energy of laser welding CGHAZ was 27 J, and the fracture mode was ductile fracture; the impact energy of submerged arc welding CGHAZ was 7.7 J, and the fracture mode was brittle fracture. The nucleation and propagation mechanism of cracks in different welding modes was established. Microcracks nucleated at the position of dislocation accumulation and remained austenite suppressed crack nucleation in laser welding CGHAZ. The nucleation site was at the M–A constituents in submerged arc welding CGHAZ. The main crack of laser welding CGHAZ was formed by one or a small number of microcracks. The main crack in submerged arc welding CGHAZ was formed by a large number of microcracks. The difference between crack nucleation and propagation mechanism is the reason why the impact energy of laser welding CGHAZ is higher than of submerged arc welding CGHAZ.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Characterization of Subsurface Microstructural Alterations Induced by Hard Turning of Inconel 718

Conventional machining especially hard turning is commonly used in aerospace industry to produce the final shape of cylindrical parts. However, the process generates damages and microstructural alterations on the surface and at the subsurface layer, in particular the cracking of hard carbides particles. The present paper focuses on investigating the probable mechanisms responsible for carbide cracking and the formation of a softened layer at a depth between 10 and 30 µm below the machined surface. Advanced techniques, such as laser confocal microscopy and field emission gun scanning electron microscope equipped with in situ picoindenter and electron backscatter diffraction, were used to characterize and analyze the evolution of the microstructure in the affected layer and propose the possible governing mechanisms for the observations.

36 MATERIALS SCIENCE↗
DOE OSTI2019

The Effect of Casting Speed on Microstructure, Microsegregation, and Mechanical Properties of High-Strength Mg-Nd-Zn-Zr Alloy

High-quality Mg-Nd-Zn-Zr magnesium alloy billets were successfully prepared by direct chill casting. The effect of casting speed on microstructure, microsegregation, and mechanical properties of the Mg-Nd-Zn-Zr alloy was systematically investigated. The results show that the as-cast microstructure is composed of equiaxed α-Mg and Mg{sub 12}Nd. Optimum values of mechanical properties were obtained corresponding to the casting speed of 90 mm/min. An age hardening at 200 °C took a remarkable effect on the mechanical properties of billets. The maximum ultimate tensile strength ~ 323.4 MPa was obtained in the billet undergoing T6 heat treatment. The shapes of concentration curves of various alloying elements (e.g., Nd and Zn) in Mg-Nd-Zn-Zr, as predicted by the Gulliver–Scheil model, resemble reasonably with the shapes measured by electron probe microanalysis.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and Hardness Evolution in Haynes 282 Nickel-Based Superalloy During Multi-variant Aging Heat Treatment

In this paper, the effect of applied multi-variant heat treatment on microstructure, phase composition and mechanical response of Haynes 282 nickel-based superalloy was investigated. For this reason, temperatures of both stages of standard two-stage aging treatment (i.e., 1010 °C/2 h + 780 °C/8 h) were extended to 900-1100 °C/2 h and 680-880 °C/8 h ranges, respectively. Consequently, 30 different variants of heat treatment were applied. The microstructural features of heat-treated samples were investigated by means of light microscopy and SEM/EDS methods, while mechanical properties were examined via microhardness measurements. It was found that by using various combinations of temperatures of the first and second stage of aging, the room temperature hardness of Haynes 282 alloy can be decreased by ~ 100 HV units or increased by up to 25 HV units as compared to that of the alloy subjected to the standard heat treatment schedule. The mechanical response of the alloy is determined by a complex structural evolution involving the secondary precipitation of γ′, M{sub 23}C{sub 6} and M{sub 6}C phases, as well as their interaction with the fcc γ matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-Throughput Microstructural Characterization and Process Correlation Using Automated Electron Backscatter Diffraction

The need to optimize the processing conditions of additively manufactured (AM) metals and alloys has driven advances in throughput capabilities for material property measurements such as tensile strength or hardness. High-throughput (HT) characterization of AM metal microstructure has fallen significantly behind the pace of property measurements due to intrinsic bottlenecks associated with the artisan and labor-intensive preparation methods required to produce highly polished surfaces. This inequality in data throughput has led to a reliance on heuristics to connect process to structure or structure to properties for AM structural materials. In this study, we show a transformative approach to achieve laser powder bed fusion (LPBF) printing, HT preparation using dry electropolishing and HT electron backscatter diffraction (EBSD). This approach was used to construct a library of > 600 experimental EBSD sample sets spanning a diverse range of LPBF process conditions for AM Kovar. This vast library is far more expansive in parameter space than most state-of-the-art studies, yet it required only approximately 10 labor hours to acquire. Build geometries, surface preparation methods, and microscopy details, as well as the entire library of >600 EBSD data sets over the two sample design versions, have been shared with intent for the materials community to leverage the data and further advance the approach. Using this library, we investigated process–structure relationships and uncovered an unexpected, strong dependence of microstructure on location within the build, when varied, using otherwise identical laser parameters.

Characterization and Analytical Technique↗
DOE OSTI2018

Achieving ultra-high strength and ductility in equiatomic CrCoNi with partially recrystallized microstructures

Despite having otherwise outstanding mechanical properties, many single-phase medium and high entropy alloys are limited by modest yield strengths. Although grain refinement offers one opportunity for additional strengthening, it requires significant and undesirable compromises to ductility. This work therefore explores an alternative, simple processing route to achieve strength by cold-rolling and annealing an equiatomic CrCoNi alloy to produce heterogeneous, partially recrystallized microstructures. Tensile tests reveal that our approach dramatically increases the yield strength (to ~1100 MPa) while retaining good ductility (total elongation ~23%) in the single-phase CrCoNi alloy. Scanning and transmission electron microscopy indicate that the strengthening is due to the non-recrystallized grains retaining their deformation-induced twins and very high dislocation densities. Furthermore, load-unload-reload tests and grain-scale digital image correlation are also used to study the accumulation of plastic deformation in our highly heterogeneous microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Role of microstructure on the actuation fatigue performance of Ni-Rich NiTiHf high temperature shape memory alloys

Here, the focus of the present study was to systematically investigate the influence of microstructure on the actuation fatigue performance of a Ni-rich NiTiHf high temperature shape memory alloy (HTSMA). Different aging heat treatments led to the formation of H-phase nano-precipitates with different sizes and morphology within the matrix, enhancing thermo-mechanical stability and enabling control of transformation temperatures. The actuation fatigue testing of specimens was performed until failure through thermally-induced reversible martensitic transformation under a constant stress (300 MPa) with two distinct upper cycle temperatures (UCT) of 300 °C and 350 °C. Consequently, the specimens heated to 700 °C and furnace cooled to 100 °C in 48 h, with relatively large precipitates, failed at average fatigue life of 15,500 cycles and exhibited 1.0% average actuation strain in the 300 °C UCT experiments, while those aged at 550 °C for 3 h, with the precipitate sizes less than 20 nm, attained an average fatigue life of 10,800 cycles and an actuation strain of 2.5%. Samples with intermediate precipitate sizes after aging at 600 °C for 10 h failed at the shortest average fatigue life of 8,200 cycles with an intermediate average actuation strain of 2.0%. Furthermore, increase in UCT decreased the fatigue life and resulted in larger average actuation strains for all samples. Overall, the current findings constitute the first systematic results demonstrating the microstructure dependence of the evolution of actuation strain, irrecoverable strain, and transformation temperatures during actuation fatigue, and actuation fatigue life of the Ni-rich Ni 50.3 Ti 29.7 Hf 20 HTSMA, demonstrating the importance of controlling the H-phase precipitate size.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Modeling the role of local crystallographic correlations in microstructures of Ti-6Al-4V using a correlated structure visco-plastic self-consistent polycrystal plasticity formulation

This paper presents a multi-level crystal plasticity-based simulation framework for modeling mechanical response and microstructure evolution of Ti-6Al-4V with α-lath/lamellar microstructures. Here, the model is a correlated structure visco-plastic self-consistent (CS-VPSC) formulation linking three scales: a single crystals micro-scale, a lath/lamellar colony meso-scale, and a lath/lamellar aggregate macro-scale. A selected hardening law for the evolution of critical resolved shear stress per slip system used in CS-VPSC is phenomenological. However, it adjusts the resistances of basal and prismatic slip systems based on the geometry of slip transfer between adjacent lamellae. Consistent with experimental evidences, the resolved shear stress on the pyramidal slip planes is dependent not only on the stress in the direction of slip but also on the two orthogonal shear stress components and the three normal stress components (non-Schmid effects). Electron backscatter diffraction (EBSD) data in conjunction with a procedure relying on α→β phase transformation is used to construct paired variants of α-laths/lamellae satisfying their local crystallographic correlations. The procedure fits volume fractions of individual laths/lamellae with the experimental EBSD data and selects a distribution of habit planes between adjacent variants with respect to the loading direction. The simulation framework is applied to interpret the deformation behavior in tension and compression along two sample directions of Ti-6Al-4V fabricated via laser powder bed fusion. Moreover, the model is used to simulate texture evolution during rolling of the material to large strains. It is demonstrated that the model is capable of predicting plastic anisotropy/asymmetry and the concomitant texture evolution. While the model reveals a significant effect of habit plane inclination with respect to the loading direction on yield stress, the comparison of the data and model predictions shows that a random distribution of habit planes fits the flow response. It is further inferred that the tension-compression asymmetry arises from the non-Schmid effects.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Experiments and simulations on solidification microstructure for Inconel 718 in powder bed fusion electron beam additive manufacturing

Previous research on the powder bed fusion electron beam additive manufacturing of Inconel 718 has established a definite correlation between the processing conditions and the solidification microstructure of components. However, the direct role of physical phenomena such as fluid flow and vaporization on determining the solidification morphology have not been investigated quantitatively. In this work, we investigate the transient and spatial evolution of the fusion zone geometry, temperature gradients, and solidification growth rates during pulsed electron beam melting of the powder bed with a focus on the role of key physical phenomena. The effect of spot density during pulsing, which relates to the amount of heating of the build area during processing, on the columnar-to-equiaxed transition of the solidification structure was studied both experimentally and theoretically. Predictions and the evaluation of the role of heat transfer and fluid flow were established using existing solidification theories combined with transient, three-dimensional numerical heat transfer and fluid flow modeling. Metallurgical characteristics of the alloy’s solidification are extracted from the transient temperature fields, and microstructure is predicted and validated using optical images and electron backscattered diffraction data from the experimental results. Simulations show that the pure liquid region solidified quickly, creating a large two-phase, mushy region that exists during the majority of solidification. While conductive heat transfer dominates in the mushy region, both the pool geometry and the solidification parameters are affected by convective heat transfer. Lastly, increased spot density during processing is shown to increase the time of solidification, lowering temperature gradients and increasing the probability of equiaxed grain formation.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Influence of scan pattern and geometry on the microstructure and soft-magnetic performance of additively manufactured Fe-Si

The influence of geometry and scan pattern on the microstructure evolution and magnetic performance of additively manufactured Fe-3Si components was investigated. To reduce eddy current losses, novel geometries were designed and built and the microstructure and properties of these samples were characterized. The laser scan pattern was shown to strongly influence both the as-built grain structure and strength of the crystallographic texture, resulting in measurable changes in the as-built magnetic performance. In thin wall samples, heat treatment resulted in an increase in the maximum relative magnetic permeability and decrease in power losses in most samples, consistent with grain growth. However, decreases in the spacing between thin walls to increase the stacking factor of the cross-section was shown to result in unwanted electrical shorting between walls and an increase in eddy current losses. Compared to simple parallel plate construction and a mesh structure, a novel cross-section design based on the Hilbert space filling curve was found to produce the lowest power losses. The mechanisms behind these results were explored using a combination of heat conduction and electromagnetic simulations, providing a route for future component and process optimization.

36 MATERIALS SCIENCE↗