Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Low Temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Nanoscale conductive niobium oxides made through low temperature phase transformation for electrocatalyst support

We report an effective approach to synthesize nanoscale Nb2O5 coated on carbon nanotubes (CNTs) and transform it at low temperatures to the conductive form of NbO2. The latter, when used as a Pt electrocatalyst support, shows significant enhancement in catalyst activity and durability in the oxygen reduction reaction (ORR). Direct phase transformation of Nb2O5 to NbO2 often requires temperatures above 1000 degrees C. Here we show that this can be achieved at a much lower temperature (e.g. 700 degrees C) if the niobium oxide is first activated with carbon. Low temperature processing allows retaining nanostructures of the oxide without sintering, keeping its high surface areas needed for being a catalyst support. We further show that Pt supported on the conductive oxides on CNTs has two times higher mass activity for the ORR than on bare CNTs. The electrochemical stability of Pt was also outstanding, with only ca. 5% loss in electrochemical surface areas and insignificant reduction in half-wave potential in ORR after 5000 potential cycles.

Huang, K↗

Substrate-dependent thermal conductivity of aluminum nitride thin-films processed at low temperature

In this paper, we report on investigation concerning the substrate-dependent thermal conductivity (k) of Aluminum Nitride (AlN) thin-films processed at low temperature by reactive magnetron sputtering. The thermal conductivity of AlN films grown at low temperature (<200 °C) on single-crystal silicon (Si) and amorphous silicon nitride (SiN) with thicknesses ranging from 100 nm to 4000 nm was measured with the transient hot-strip technique. The k values for AlN films on SiN were found significantly lower than those on Silicon consistently with their microstructures revealed by X-ray diffraction, high resolution scanning electron microscopy, and transmission electron microscopy. The change in k was due to the thermal boundary resistance found to be equal to 10 × 10{sup −9} Km{sup 2}W{sup −1} on SiN against 3.5 × 10{sup −9} Km{sup 2}W{sup −1} on Si. However, the intrinsic thermal conductivity was determined with a value as high as 200 Wm{sup −1}K{sup −1} whatever the substrate.

36 MATERIALS SCIENCE↗

Composite Mixed Ionic-electronic Conducting Materials for Low-Temperature Thermochemical CO 2 Splitting and Syngas Generation

An effective strategy to design platinum group metal (PGM) free redox catalysts for “low temperature” CO 2 splitting followed with methane partial oxidation was proposed and validated. Composites of mixed ionic-electronic conductive (MIEC) oxides were found to be highly effective at relatively low temperatures (600–750 °C). Specifically, perovskite structured LaNi 0.35 Fe 0.65 O 3 and rock salt structured Ce 0.85 Gd 0.1 Cu 0.05 O 2-δ , as two compatible yet structurally distinct MIEC oxides, were integrated into composite redox catalyst particles. Resulting from the synergistic effect of the two MIEC phases, 90% CO 2 to CO conversion was demonstrated at 750 °C. Up to 90% methane conversion with 96% CO selectivity was also achieved in the methane POx step. The redox catalysts were characterized in detail to illustrate the underlying mechanisms for the synergistic effects. Electrical conductivity relaxation (ECR) measurements indicated significantly lowered activation energy for lattice oxygen (O 2- ) migration (0.43 eV). The enhanced oxygen migration in turn led to reversible exsolution of active transition metal nanoparticles (Ni–Fe alloy) from the mixed oxide, serving as active sites for methane activation while further enhancing lattice oxygen exchange, as confirmed by in situ X-ray diffraction and transmission electron microscopy. As a result, the composite redox catalysts demonstrate superior redox activity, coke resistance, and long term redox stability, making them potentially suitable for CO 2 utilization and methane partial oxidation under a hybrid redox process scheme.

Jiang, Qiongqiong↗

Nanosized low-temperature phases of titanium(IV) oxide with anatase and η-phase structures: composition, structure, and photocatalytic properties

Nanosized low-temperature modifications of titanium(IV) oxide with the anatase and η-phase (TiO{sub 2–x}•mH{sub 2}O) structures were prepared by the sulfate method (pH <3) and for the first time characterized by a complex of methods (X-ray diffractometry, scanning electron microscopy, IR spectroscopy, Raman spectroscopy, differential scanning calorimetry, low-temperature sorption capacity of samples to nitrogen, and differentiating dissolution). The physicochemical properties of the modifications were compared. Differences in compositions of the surface and volumes of the samples, compositions and structures of the phases (structure of η-phase is superstructure to anatase), and microstructure elements (sizes of crystallites, nanoparticles, and specific surface area; volume of nano- and ultrananopores) were revealed. The region of η-phase stability was found in the coordinates of temperature (T = 50–95 °C) and hydrolysis duration (τ = 10–80 min) and temperature (T≤200 °C) and annealing duration (τ <6 h). The distinctions in the thermal behavior of the nanosized anatase and η-phase were studied. The photocatalytic activity (PCA) is determined by the physicochemical characteristics of the samples and phases and also by the composition and structure of the decomposed substrate. In the case of difenoxazole, the PCA is affected by the compositions of the samples, phases, and surface (the presence of OH groups) and specific surface area, whereas the composition of the samples and specific surface area affect the PCA in the case of thiamethoxam.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Low Temperature Creep of Hot-Extruded Near-Stoichiometric NiTi Shape Memory Alloy: Effect of Thermal Cycling - Part 2

This paper is the first report on the effect prior low temperature creep on the thermal cycling behavior of NiTi. The isothermal low temperature creep behavior of near-stoichiometric NiTi between 300 and 473 K was discussed in Part I. The effect of temperature cycling on its creep behavior is reported in the present paper (Part II). Temperature cycling tests were conducted between either 300 or 373 K and 473 K under a constant applied stress of either 250 or 350 MPa with hold times lasting at each temperature varying between 300 and 700 h. Each specimen was pre-crept either at 300 or at 473 K for several months under an identical applied stress as that used in the subsequent thermal cycling tests. Irrespective of the initial pre-crept microstructures, the specimens exhibited a considerable increase in strain with each thermal cycle so that the total strain continued to build-up to 15 to 20 percent after only 5 cycles. Creep strains were immeasurably small during the hold periods. It is demonstrated that the strains in the austenite and martensite are linearly correlated. Interestingly, the differential irrecoverable strain, in the material measured in either phase decreases with increasing number of cycles, similar to the well-known Manson-Coffin relation in low cycle fatigue. Both phases are shown to undergo strain hardening due to the development of residual stresses. Plots of true creep rate against absolute temperature showed distinct peaks and valleys during the cool-down and heat-up portions of the thermal cycles, respectively. Transformation temperatures determined from the creep data revealed that the austenitic start and finish temperatures were more sensitive to the pre-crept martensitic phase than to the pre-crept austenitic phase. The results are discussed in terms of a phenomenological model, where it is suggested that thermal cycling between the austenitic and martensitic phase temperatures or vice versa results in the deformation of the austenite and a corresponding development of a back stress due to a significant increase in the dislocation density during thermal cycling.

Raj, S. V.↗

Low temperature double-layer capacitors

Double-layer capacitors capable of operating at extremely low temperatures (e.g., as low as -75.degree. C.) are disclosed. Electrolyte solutions combining a base solvent (e.g., acetonitrile) and a cosolvent are employed to lower the melting point of the base electrolyte. Example cosolvents include methyl formate, ethyl acetate, methyl acetate, propionitrile, butyronitrile, and 1,3-dioxolane. An optimized concentration (e.g., 0.10 M to 0.75 M) of salt, such as tetraethylammonium tetrafluoroborate, is dissolved into the electrolyte solution. In some cases (e.g., 1,3-dioxolane cosolvent) additives, such as 2% by volume triethylamine, may be included in the solvent mixture to prevent polymerization of the solution. Conventional device form factors and structural elements (e.g., porous carbon electrodes and a polyethylene separator) may be employed.

Brandon, Erik J.↗

Appalachian Basin Play Fairway Analysis: Thermal Quality Analysis in Low-Temperature Geothermal Play Fairway Analysis (GPFA-AB)

This collection of files are part of a larger dataset uploaded in support of Low Temperature Geothermal Play Fairway Analysis for the Appalachian Basin (GPFA-AB). Phase 1 of the GPFA-AB project identified potential Geothermal Play Fairways within the Appalachian basin of Pennsylvania, West Virginia and New York. This was accomplished through analysis of 4 key criteria: thermal quality, natural reservoir productivity, risk of seismicity, and heat utilization. Each of these analyses represent a distinct project task, with the fifth task encompassing combination of the 4 risks factors. Supporting data for all five tasks has been uploaded into the Geothermal Data Repository node of the National Geothermal Data System (NGDS). This submission comprises the data for Thermal Quality Analysis (project task 1) and includes all of the necessary shapefiles, rasters, datasets, code, and references to code repositories that were used to create the thermal resource and risk factor maps as part of the GPFA-AB project. The identified Geothermal Play Fairways are also provided with the larger dataset. Figures (.png) are provided as examples of the shapefiles and rasters. The regional standardized 1 square km grid used in the project is also provided as points (cell centers), polygons, and as a raster. Two ArcGIS toolboxes are available: 1) RegionalGridModels.tbx for creating resource and risk factor maps on the standardized grid, and 2) ThermalRiskFactorModels.tbx for use in making the thermal resource maps and cross sections. These toolboxes contain item description documentation for each model within the toolbox, and for the toolbox itself. This submission also contains three R scripts: 1) AddNewSeisFields.R to add seismic risk data to attribute tables of seismic risk, 2) StratifiedKrigingInterpolation.R for the interpolations used in the thermal resource analysis, and 3) LeaveOneOutCrossValidation.R for the cross validations used in the thermal interpolations. Some file descriptions make reference to various 'memos'. These are contained within the final report submitted October 16, 2015. Each zipped file in the submission contains an 'about' document describing the full Thermal Quality Analysis content available, along with key sources, authors, citation, use guidelines, and assumptions, with the specific file(s) contained within the .zip file highlighted. UPDATE: Newer version of the Thermal Quality Analysis has been added here: https://gdr.openei.org/submissions/879 (Also linked below) Newer version of the Combined Risk Factor Analysis has been added here: https://gdr.openei.org/submissions/880 (Also linked below)

15 GEOTHERMAL ENERGY↗

Electronic Interlayer Coupling in the Low-Temperature Tetragonal Phase of La1.79Eu0.2Sr0.01CuO4

The electronic interlayer transport of the lightly doped antiferromagnet La1.79Eu0.2Sr0.01CuO4 has been studied by means of magnetoresistance measurements. The central problem addressed concerns the differences between the electronic interlayer coupling in the tetragonal low-temperature (LTT) phase and the orthorhombic low-temperature (LTO) phase. The key observation is that the spin-flip-induced drop in the c-axis magnetoresistance of the LTO phase, which is characteristic for pure La2-xSrxCuO4, dramatically decreases in the LTT phase. The results show that the transition from orthorhombic to tetragonal symmetry and from collinear to noncollinear antiferromagnetic spin structure eliminates the strain dependent anisotropic interlayer hopping as well as the concomitant spin-valve-type transport channel. Implications for the stripe ordered LTT phase of La2-xBaxCuO4 are briefly discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low temperature superconductor and aligned high temperature superconductor magnetic dipole system and method for producing high magnetic fields

A dipole-magnet system and method for producing high-magnetic-fields, including an open-region located in a radially-central-region to allow particle-beam transport and other uses, low-temperature-superconducting-coils comprised of low-temperature-superconducting-wire located in radially-outward-regions to generate high magnetic-fields, high-temperature-superconducting-coils comprised of high-temperature-superconducting-tape located in radially-inward-regions to generate even higher magnetic-fields and to reduce erroneous fields, support-structures to support the coils against large Lorentz-forces, a liquid-helium-system to cool the coils, and electrical-contacts to allow electric-current into and out of the coils. The high-temperature-superconducting-tape may be comprised of bismuth-strontium-calcium-copper-oxide or rare-earth-metal, barium-copper-oxide (ReBCO) where the rare-earth-metal may be yttrium, samarium, neodymium, or gadolinium. Advantageously, alignment of the large-dimension of the rectangular-cross-section or curved-cross-section of the high-temperature-superconducting-tape with the high-magnetic-field minimizes unwanted erroneous magnetic fields. Alignment may be accomplished by proper positioning, tilting the high-temperature-superconducting-coils, forming the high-temperature-superconducting-coils into a curved-cross-section, placing nonconducting wedge-shaped-material between windings, placing nonconducting curved-and-wedge-shaped-material between windings, or by a combination of these techniques.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Facile synthesis of the nitrogen-doped graphene quantum dots at low temperature for cellular labeling

Highlights: • The N-GQDs are prepared via a facile stirring method on a magnetic stirrer at low temperature. • The N-GQDs exhibit outstanding biocompatibility in the live HeLa cells for biological applications. • The live cells keep a 100% survival rate in the high N-GQDs concentration of 200 μg mL{sup −1} for 48 h. - Abstract: A facile one-step approach is developed for the large-scale synthesis of nitrogen doped graphene quantum dot (N-GQDs) at low temperature by using citric acid (CA) as the precursor. The emission wavelength of the N-GQDs is nearly excitation-dependent, which may mirror the effects from particles of different sizes and distribution of different emissive sites on nanoparticles. Moreover, the products are then tested with live Hela cells for the extraordinary biocompatibility. The cellular viability is remained to be 100% even after a 48 h exposure with the high N-GQDs concentration of 200 μg mL{sup −1} and this survival rate is really much higher than that have been reported previously. The as-prepared N-GQDs with negligible inherent toxicity exhibit excellent biological applications such as bio-imaging and cell tracking.

60 APPLIED LIFE SCIENCES↗

Low-Temperature Supercapacitors

An effort to extend the low-temperature operational limit of supercapacitors is currently underway. At present, commercially available non-aqueous supercapacitors are rated for a minimum operating temperature of -40 C. A capability to operate at lower temperatures would be desirable for delivering power to systems that must operate in outer space or in the Polar Regions on Earth. Supercapacitors (also known as double-layer or electrochemical capacitors) offer a high power density (>1,000 W/kg) and moderate energy density (about 5 to 10 Wh/kg) technology for storing energy and delivering power. This combination of properties enables delivery of large currents for pulsed applications, or alternatively, smaller currents for low duty cycle applications. The mechanism of storage of electric charge in a supercapacitor -- at the electrical double-layer formed at a solid-electrode/liquid-electrolyte interface -- differs from that of a primary or secondary electrochemical cell (i.e., a battery) in such a manner as to impart a long cycle life (typically >10(exp 6) charge/discharge cycles).

Brandon, Erik J.↗

Low temperature synthesis of LnOF rare-earth oxyfluorides through reaction of the oxides with PTFE

Highlights: Black-Right-Pointing-Pointer Low temperature synthesis of LnOF rare-earth oxyfluorides from Ln{sub 2}O{sub 3} and PTFE (CF{sub 2}). Black-Right-Pointing-Pointer Rhombohedral LnOF is the major phase and forms as nanocrystals, 29-103 nm. Black-Right-Pointing-Pointer Expected lanthanide contraction observed in lattice parameters and bond lengths. Black-Right-Pointing-Pointer TbOF orders antiferromagnetically at 10 K and has a metamagnetic transition at 1.8 T. Black-Right-Pointing-Pointer GdOF orders antiferromagnetically at 5 K, other LnOF are paramagnetic. -- Abstract: A low temperature solid-state synthesis route, employing polytetrafluoroethylene (PTFE) and the rare-earth oxides, for the formation of the LnOF rare-earth oxyfluorides (Ln = Y, La, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er), is reported. With the exception of LaOF, which forms in a tetragonal variant, rhomobohedral LnOF is found to be the major product of the reaction. In the case of PrOF, a transition from the rhombohedral to the cubic fluorite phase is observed on heating in air to 500 Degree-Sign C. X-ray diffraction shows the expected lanthanide contraction in the lattice parameters and bond lengths. Magnetic susceptibility measurements show antiferromagnetic-like ordering in TbOF, T{sub m} = 10 K, with a metamagnetic transition at a field {mu}{sub 0}H{sub t} = 1.8 T at 2 K. An antiferromagnetic transition, T{sub N} = 4 K, is observed in GdOF. Paramagnetic behavior is observed above 2 K in PrOF, NdOF, DyOF, HoOF and ErOF. The magnetic susceptibility of EuOF is characteristic of Van Vleck paramagnetism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mixed conductive composites for ‘Low-Temperature’ thermo-chemical CO 2 splitting and syngas generation

An effective strategy to design platinum group metal (PGM) free redox catalysts for “low temperature” CO 2 splitting followed with methane partial oxidation was proposed and validated. Composites of mixed ionic-electronic conductive (MIEC) oxides were found to be highly effective at relatively low temperatures (600–750 °C). Specifically, perovskite structured LaNi 0.35 Fe 0.65 O 3 and rock salt structured Ce 0.85 Gd 0.1 Cu 0.05 O 2–δ , as two compatible yet structurally distinct MIEC oxides, were integrated into composite redox catalyst particles. Resulting from the synergistic effect of the two MIEC phases, 90% CO 2 to CO conversion was demonstrated at 750 °C. Up to 90% methane conversion with 96% CO selectivity was also achieved in the methane POx step. The redox catalysts were characterized in detail to illustrate the underlying mechanisms for the synergistic effects. Electrical conductivity relaxation (ECR) measurements indicated significantly lowered activation energy for lattice oxygen (O 2– ) migration (0.43 eV). The enhanced oxygen migration in turn led to reversible exsolution of active transition metal nanoparticles (Ni–Fe alloy) from the mixed oxide, serving as active sites for methane activation while further enhancing lattice oxygen exchange, as confirmed by in situ X-ray diffraction and transmission electron microscopy. In conclusion, the composite redox catalysts demonstrate superior redox activity, coke resistance, and long term redox stability, making them potentially suitable for CO 2 utilization and methane partial oxidation under a hybrid redox process scheme.

03 NATURAL GAS↗

Anomalous Low-Temperature Enhancement of Supercurrent in Topological-Insulator Nanoribbon Josephson Junctions: Evidence for Low-Energy Andreev Bound States

We report anomalous enhancement of the critical current at low temperatures in gate-tunable Josephson junctions made from topological insulator BiSbTeSe 2 nanoribbons with superconducting Nb electrodes. In contrast to conventional junctions, as a function of the decreasing temperature T, the increasing critical current I c exhibits a sharp upturn at a temperature T * around 20% of the junction critical temperature for several different samples and various gate voltages. The I c vs T demonstrates a short junction behavior for T > T * , but crosses over to a long junction behavior for T < T * with an exponential T dependence I c ∝ exp(–k B T/δ), where k B is the Boltzmann constant. The extracted characteristic energy scale δ is found to be an order of magnitude smaller than the induced superconducting gap of the junction. Furthermore, we attribute the long-junction behavior with such a small δ to low-energy Andreev bound states arising from winding of the electronic wave function around the circumference of the topological insulator nanoribbon.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Calculation of pressure broadening parameters for the CO-He system at low temperatures

Theoretical pressure broadening parameters were computed for the 0-1 and 1-2 rotational transitions of CO in He at very low temperatures and compared with the recent experimental measurements at 4.2 K. The interaction potential was taken from extensive SCF-CI calculations, molecular collision dynamics were described by essentially exact converged close coupling calculations, and pressure broadening cross sections were obtained from the collisional S matrices within the accurate Fano-Ben Reuven framework. Resonances at low collision energies give rise to an increase in the thermally averaged cross sections at low temperatures. Although previous calculations for this system at higher temperatures (77-300 K) were in good accord with experiment, at 4.2 K predicted values are about two times larger than experiment; possible sources of this discrepancy are discussed.

Green, S.↗