Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Laminarization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Natural laminar flow flight experiments on a swept-wing business jet

Flight test experiments have been conducted to measure the extent and nature of laminar flow on a smoothed test region of a swept-wing business jet. Surface hot film anemometers and sublimating chemicals were used for transition detection. Surface pressure distributions were measured using pressure belts. Instrumentation techniques and problems are presented. Correlation was obtained between the hot film and sublimating chemicals for transition detection. Taylor-Goertler vortices were observed for some flight conditions. Boundary layer stability analysis is being conducted using measured pressure distributions to determine the correlation possible for transition prediction on swept wings.

Wentz, W. H., Jr.↗
NASA NTRS1984

Progress in natural laminar flow research

For decades, since the earliest attempts to obtain natural laminar flow (NLF) on airplanes, three classical objections to its practicality have been held in the aeronautical community. These objectives concerned first, the capability to manufacture practical airframe surfaces smooth enough for NLF; second, the apparent inherent instability and sensitivity of NLF; and third, the accumulation of contamination such as insect debris in flight. This paper explains recent progress in our understanding of the achieveability and maintainability of NLF on modern airframe surfaces. This discussion explains why previous attempts to use NLF failed and what has changed regarding the three classical objections to NLF practicality. Future NASA research plans are described concerning exploring the limits of NLF usefulness, production tolerances, operational considerations, transition behavior and measurement methods, and NLF design applications.

Holmes, B. J.↗
NASA NTRS1985

Continuous Laminar-Smoke Generator

Single smoke filament used to study flow in low-speed wind tunnels. Use of small-diameter single laminar smoke stream allows examination of flow structures at higher resolution, and continuous operation facilitates use.

Weinstein, L. M.↗
NASA NTRS1984

Natural laminar flow airfoil design considerations for winglets on low-speed airplanes

Winglet airfoil section characteristics which significantly influence cruise performance and handling qualities of an airplane are discussed. A good winglet design requires an airfoil section with a low cruise drag coefficient, a high maximum lift coefficient, and a gradual and steady movement of the boundary layer transition location with angle of attack. The first design requirement provides a low crossover lift coefficient of airplane drag polars with winglets off and on. The other requirements prevent nonlinear changes in airplane lateral/directional stability and control characteristics. These requirements are considered in the design of a natural laminar flow airfoil section for winglet applications and chord Reynolds number of 1 to 4 million.

Vandam, C. P.↗
NASA NTRS1984

Laminar heat-transfer distributions on biconics at incidence in hypersonic-hypervelocity flows

Laminar heating distributions were measured at hypersonic-hypervelocity flow conditions on a 1.9-percent-scale model of an aeroassisted vehiclee proposed for missions to a number of planets. This vehicle is a spherically blunted, 12.84/7deg biconic with the fore-cone axis bent upward 7 deg relative to the aft-cone axis to provide selftrim capability. Also tested was a straight biconic (i.e., without nose bend) with the same nose radius and half-angles as the bent-nose biconic. These measurements were made in the Langley Expansion Tube at free-stream velocities from 4.5 to 6.9 km/sec and Mach numbers from 6.0 to 9.0 with helium, nitrogen, air, and carbon dioxide test gases. The range of calculated thermochemical equilibrium normal-shock density ratios for these four test gases was 4 to 19. Angles of attack, referenced to the aft-cone, varied from 0 to 20 deg. Heating distributions predicted with a parabolized Navier-Stokes (PNS) code were compared with measurement for helium and air test gases. Measured windward and leeward heating levels were generally underpredicted by the PNS code for both test gases, and agreement was poorer on the leeward side than on the windward side.

Miller, C. G., III↗
NASA NTRS1985

Numerical approach for the aerodynamic analysis if airfoils with laminar separation

A numerical method for simultaneously and efficiently coupling an external subsonic potential flow and an interior viscous flow such that the two flows match at an interfacing boundary is discussed. Both a panel method and a simple point compressible vortex model are used for the outer potential field. The interior flow solvers which were used are the Navier-Stokes and Euler codes of T. J. Coakley and the Euler code of A. Verhoff. In order to test compatibility, the panel method is coupled to the less expensive Euler codes since the coupling procedure is identical with the Navier-Stokes code. The results show significant efficiency improvements can be obtained over the uncoupled approach. Results also indicate the outer potential flow is best represented by the simple point compressible vortex model. The panel method couples smoothly to Coakley's implicit code but is numerically incompatible as coupled with the explicit Euler code. An improved Navier-Stokes code is under initial development which extends the Euler code to include the necessary viscous terms. Results are shown for all infinite length channel with one wavy periodic wall with and without laminar separation.

Halt, D. W.↗
NASA NTRS1985

Continuous laminar smoke generator

A smoke generator capable of emitting a very thin, laminar stream of smoke for use in high detail flow visualization was invented. The generator is capable of emitting a larger but less stable rope of smoke. The invention consists of a pressure supply and fluid supply which supply smoke generating fluid to feed. The feed tube is directly heated by electrical resistance from current supplied by power supply and regulated by a constant temperature controller. A smoke exit hole is drilled in the wall of feed tube. Because feed tube is heated both before and past exit hole, no condensation of smoke generating occurs at the smoke exit hole, enabling the production of a very stable smoke filament. The generator is small in size which avoids wind turbulence in front of the test model.

Weinstein, L. M.↗
NASA NTRS1985

Experimental aerodynamic heating to simulated space shuttle tiles in laminar and turbulent boundary layers with variable flow angles at a nominal Mach number of 7

The heat transfer to simulated shuttle thermal protection system tiles was investigated experimentally by using a highly instrumented metallic thin wall tile arranged with other metal tiles in a staggered tile array. Cold wall heating rate data for laminar and turbulent flow were obtained in the Langley 8 foot high Temperature Tunnel at a nominal Mach number of 7, a nominal total temperature of 3300R, a free stream unit Reynolds number from 3.4 x 10 sup 5 to 2.2 10 sup 6 per foot, and a free stream dynamic pressure from 2.1 to 9.0 psia. Experimental data are presented to illustrate the effects of flow angularity and gap width on both local peak heating and overall heating loads. For the conditions of the present study, the results show that localized and total heating are sensitive to changes in flow angle only for the test conditions of turbulent boundary layer flow with high kinetic energy and that a flow angle from 30 deg to 50 deg will minimize the local heating.

Avery, D. E.↗
NASA NTRS1984

GASP cloud encounter statistics - Implications for laminar flow control flight

The cloud observation archive from the NASA Global Atmospheric Sampling Program (GASP) is analyzed in order to derive the probability of cloud encounter at altitudes normally flown by commercial airliners, for application to a determination of the feasability of Laminar Flow Control (LFC) on long-range routes. The probability of cloud encounter is found to vary significantly with season. Several meteorological circulation features are apparent in the latitudinal distribution of cloud cover. The cloud encounter data are shown to be consistent with the classical midlatitude cyclone model with more clouds encountered in highs than in lows. Aircraft measurements of route-averaged time-in-clouds fit a gamma probability distribution model which is applied to estimate the probability of extended cloud encounter, and the associated loss of LFC effectiveness along seven high-density routes. The probability is demonstrated to be low.

Jasperson, W. H.↗
NASA NTRS1985

Analysis of buoyancy effect on fully developed laminar heat transfer in a rotating tube

Laminar heat transfer is analyzed in a tube rotating about an axis perpendicular to the tube axis. The solution applies for flow that is either radially outward from the axis of rotation, or radially inward toward the axis of rotation. The conditions are fully developed, and there is uniform heat addition at the tube wall. The analysis is performed by expanding velocities and temperature in power series using the Taylor number as a perturbation parameter. Coriolis and buoyancy forces caused by tube rotation are included, and the solution is calculated through second-order terms. The secondary flow induced by the Coriolis terms always tends to increase the heat transfer coefficient; this effect can dominate for small wall heating. For radial inflow, buoyancy also tends to improve heat transfer. For radial outflow, however, buoyancy tends to reduce heat transfer; for large wall heating this effect can dominate, and there is a net reduction in heat transfer coefficient.

Siegel, R.↗
NASA NTRS1985

Flight evaluation of an insect contamination protection system for laminar flow wings

The maintenance of minimum wing leading edge contamination is critical to the preservation of drag-reducing laminar flow; previous methods for the prevention of leading edge contamination by insects have, however, been rendered impractical by their excessive weight, cost, or inconvenience. Attention is presently given to the results of a NASA flight experiment which evaluated the performance of a porous leading edge fluid-discharge ice protection system in the novel role of insect contamination removal; high insect contamination conditions were also noted in the experiment. Very small amounts of the fluid are found to be sufficient for insect contamination protection.

Croom, C. C.↗
NASA NTRS1985

Manufacturing tolerances for natural laminar flow airframe surfaces

Published aircraft surface waviness and boundary layer transition measurements imply that currently achievable low levels of surface waviness are compatible with the natural laminar flow (NLF) requirements of business and commuter aircraft, in the cases of both metallic and composite material airframes. The primary challenge to the manufacture of NLF-compatible surfaces is two-dimensional roughness in the form of steps and gaps at structural joints. Attention is presently given to recent NASA investigations of manufacturing tolerance requirements for NLF surfaces, including flight experiment results.

Holmes, B. J.↗
NASA NTRS1985

Ground vibration test of the laminar flow control JStar airplane

A ground vibration test was conducted on a Lockheed JetStar airplane that had been modified for the purpose of conducting laminar flow control experiments. The test was performed prior to initial flight flutter tests. Both sine-dwell and single-point-random excitation methods were used. The data presented include frequency response functions and a comparison of mode frequencies and mode shapes from both methods.

Kehoe, M. W.↗
NASA NTRS1985

Design considerations for application of laminar flow control systems to transport aircraft

The current status of the laminar-flow control LFC technology is summarized. Factors that have previously inhibited the application of LFC are first reviewed. Involved are the effects of atmospheric ice crystals, surface irregularities, acoustical environment, and off-design operating conditions. Aircraft design trends that are different from turbulent aircraft are discussed as are various design requirements unique to the LFC systems. Current design approaches for the principal LFC systems are reviewed. These include the system for protection of the leading-edge region from surface contamination and icing and the system for removal of a portion of the boundary-layer air. The latter includes consideration of both multiple spanwise suction slots and distributed perforations and required differences between the wing-box and leading-edge box regions.

Braslow, A. L.↗
NASA NTRS1986

A New Method for Laminar Boundary Layer Transition Visualization in Flight: Color Changes in Liquid Crystal Coatings

The visualization of laminar to turbulent boundary layer transition plays an important role in flight and wind tunnel aerodynamic testing of aircraft wing and body surfaces. Visualization can help provide a more complete understanding of both transition location as well as transition modes; without visualization, the transition process can be very difficult to understand. In the past, the most valuable transition visualization methods for fight applications included sublimating chemicals and oil flows. Each method has advantages and limitations. In particular, sublimating chemicals are impractical to use in subsonic applications much above 20,000 feet because of the greatly reduced rates of sublimation at lower temperatures (less than -4 degrees Fahrenheit). Both oil flow and sublimating chemicals have the disadvantage of providing only one good data point per flight. Thus, for many important flight conditions, transition visualization has not been readily available. This paper discusses a new method for visualizing transition in fight by the use of liquid crystals. The new method overcomes the limitations of past techniques, and provides transition visualization capability throughout almost the entire altitude and speed ranges of virtually all subsonic aircraft flight envelopes. The method also has wide applicability for supersonic transition visualization in flight and for general use in wind tunnel research over wide subsonic and supersonic speed ranges.

Holmes, Bruce J.↗
NASA NTRS1986

Heat and mass transfer in a dissociated laminar boundary layer of air with consideration of the finite rate of chemical reaction

A numerical investigation of heat and mass transfer in a dissociated laminar boundary layer of air on an isothermal flat plate is carried out for different degrees of cooling of the wall. A finite-difference chemical model is used to study elementary reactions involving NO2 and N2O. The analysis is based on equations of continuity, momentum, energy, conservation and state for the two-dimensional viscous flow of a reacting multicomponent mixtures. Attention is given to the effects of both catalyticity and noncatalyticity of the wall.

Oyegbesan, A. O.↗
NASA NTRS1986

Natural laminar flow flight experiments on a swept wing business jet-boundary layer stability analyses

The linear boundary layer stability analyses and their correlation with data of 18 cases from a natural laminar flow (NLF) flight test program using a Cessna Citation 3 business jet are described. The transition point varied from 5% to 35% chord for these conditions, and both upper and lower wing surfaces were included. Altitude varied from 10,000 to 43,000 ft and Mach number from 0.3 to 0.8. Four cases were at nonzero sideslip. Although there was much scatter in the results, the analyses of boundary layer stability at the 18 conditions led to the conclusion that crossflow instability was the primary cause of transition. However, the sideslip cases did show some interaction of crossflow and Tollmien-Schlichting disturbances. The lower surface showed much lower Tollmien-Schlichting amplification at transition than the upper surface, but similar crossflow amplifications. No relationship between Mach number and disturbance amplification at transition could be found. The quality of these results is open to question from questionable wing surface quality, inadequate density of transition sensors on the wing upper surface, and an unresolved pressure shift in the wing pressure data. The results of this study show the need for careful preparation for transition experiments. Preparation should include flow analyses of the test surface, boundary layer disturbance amplification analyses, and assurance of adequate surface quality in the test area. The placement of necessary instruments and usefulness of the resulting data could largely be determined during the pretest phase.

Rozendaal, R. A.↗