Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ICE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Additional Large-Drop Ice Accretion Test Results for a Large Scale Swept Wing Section from January 2022

In-flight icing is an important consideration that affects aircraft design, performance, certification and safety. Newer regulations combined with increasing demand to reduce fuel burn, emissions and noise are driving a need for improvements in icing simulation capability. To that end, this paper presents the results of additional ice accretion testing conducted in the NASA Icing Research Tunnel in January 2022 with a large swept wing section typical of a modern commercial transport. The model was based upon a section of the Common Research Model wing at the 64% semispan station with a streamwise chord length of 136 in. The test conditions were developed with an icing scaling analysis to generate similar conditions for a small median volumetric diameter (MVD) = 25 μm cloud and a large MVD = 110 μm cloud. A series of tests were conducted over a range of total temperature from -23.8 ˚C to -1.4 ˚C with all other conditions held constant. Another series of tests explored cloud MVD variations from 50 μm to 230 μm while holding constant certain scaling parameters. The variation in ice mass and scanned ice volume across repeat conditions was approximately 50% lower than the uncertainty in the cloud MVD and liquid water content. The measured ice mass and volume calculated from the 3D scans were used to compute the mass to volume ratio that is sometimes referred to as ice density or void fraction. When the ice volume based on the ice shape maximum combined cross section was used to determine this ratio, the resulting values were in the range of 240 to 455 kg/m 3 . This is consistent with analogous values previously reported in the literature. The ice shape mass and volume increased with MVD from 50 to 230 μm at fixed values of the scaling parameters. The ice mass to volume ratio was approximately constant for all of the cases which showed that the accreted mass and volume increased at approximately the same rate. These results demonstrate the significance of cloud MVD on ice shape mass and volume.

Ice accretion, Large drops, Wind tunnel↗

Additional Large-Drop Ice Accretion Test Results for a Large Scale Swept Wing Section from January 2022

In-flight icing is an important consideration that affects aircraft design, performance, certification and safety. Newer regulations combined with increasing demand to reduce fuel burn, emissions and noise are driving a need for improvements in icing simulation capability. To that end, this paper presents the results of additional ice accretion testing conducted in the NASA Icing Research Tunnel in January 2022 with a large swept wing section typical of a modern commercial transport. The model was based upon a section of the Common Research Model wing at the 64% semispan station with a streamwise chord length of 136 in. The test conditions were developed with an icing scaling analysis to generate similar conditions for a small median volumetric diameter (MVD) = 25 μm cloud and a large MVD = 110 μm cloud. A series of tests were conducted over a range of total temperature from -23.8 ˚C to -1.4 ˚C with all other conditions held constant. Another series of tests explored cloud MVD variations from 50 μm to 230 μm while holding constant certain scaling parameters. The variation in ice mass and scanned ice volume across repeat conditions was approximately 50% lower than the uncertainty in the cloud MVD and liquid water content. The measured ice mass and volume calculated from the 3D scans were used to compute the mass to volume ratio that is sometimes referred to as ice density or void fraction. When the ice volume based on the ice shape maximum combined cross section was used to determine this ratio, the resulting values were in the range of 240 to 455 kg/m3. This is consistent with analogous values previously reported in the literature. The ice shape mass and volume increased with MVD from 50 to 230 μm at fixed values of the scaling parameters. The ice mass to volume ratio was approximately constant for all of the cases which showed that the accreted mass and volume increased at approximately the same rate. These results demonstrate the significance of cloud MVD on ice shape mass and volume.

Ice accretion↗

Adhesion of impure ice on surfaces

The undesirable buildup of ice can compromise the operational safety of ships in the Arctic to high-flying airplanes, thereby having a detrimental impact on modern life in cold climates. The obstinately strong adhesion between ice and most functional surfaces makes ice removal an energetically expensive and dangerous affair. Hence, over the past few decades, substantial efforts have been directed toward the development of passive ice-shedding surfaces. Conventionally, such research on ice adhesion has almost always been based on ice solidified from pure water. However, in all practical situations, freezing water has dissolved contaminants; ice adhesion studies of which have remained elusive thus far. Here, in this work, we cast light on the fundamental role played by various impurities (salt, surfactant, and solvent) commonly found in natural water bodies on the adhesion of ice on common structural materials. We elucidate how varying freezing temperature & contaminant concentration can significantly alter the resultant ice adhesion strength making it either super-slippery or fiercely adherent. The entrapment of impurities in ice changes with the rate of freezing and ensuing adhesion strength increases as the cooling temperature decreases. We discuss the possible role played by the in situ generated solute enriched liquid layer and the nanometric water-like disordered ice layer sandwiched between ice and the substrate behind these observations. Our work provides useful insights into the elementary nature of impure water-to-ice transformation and contributes to the knowledge base of various natural phenomena and rational design of a broad spectrum of anti-icing technologies for transportation, infrastructure, and energy systems.

36 MATERIALS SCIENCE↗

Dynamic compression effects of H 2 ⁡O in a dynamic diamond anvil cell: Origin of metastable ice VII and its crystal growth kinetics

We report on the structural verification of metastable ice VII solidifying in the phase space of ice VI at 1.80 GPa at room temperature. Using time-resolved (TR) x-ray diffraction and TR ruby luminescence paired with high-speed microphotography utilizing a dynamic diamond anvil cell, an initial compression rate range from 0.12 to 95.84 GPa/s was explored. The solidification pressure of metastable ice VII has a potential sigmoidal dependence upon compression rate with a turnover compression rate of ∼80 GPa/s. The preferred crystallization of ice VII in the stability field of ice VI is due to the increased nucleation rate of ice VII over ice VI at 1.77 GPa that is driven by the surface energy difference between the liquid and solid phases along with the change in Gibbs free energy of solidification. The dynamic pressure-volume–compression behaviors of ice phases (VI and VII) show a lattice stiffening in both phases, especially during the compression loading. It is also found that the compression rate greatly affects the solid-solid phase transition between ice VI and VII but does not affect the liquid-solid transition between water and ice VI as much. Lastly, a third phase transition was found to occur after metastable ice VII transforms into high-density amorphous (HDA) ice, which could be a disordered hydrogen-bonded network configuration of ice VII forming out of HDA ice facilitated by the decoupling of the oxygen movement and reorientation of the H 2⁡ O molecule. These results demonstrate the complexity of a seemingly simple molecule H 2⁡ O, how it can readily change its static properties with the modification of (de)compression rate, and highlight the need to use multiple TR structural and spectroscopic probes at higher time resolutions to realize the most comprehensive understanding.

Chemical bonding↗

Topological defects from doping and quenched disorder in artificial ice systems

We examine the ice-rule obeying and ice-rule breaking vertices in an artificial spin ice system created using magnetic vortices in type-II superconductors with nanostructured pinning arrays. We show that this system can be doped by changing the external field to move the number of vortices away from commensurability and create sites that contain two or zero vortices. For a square ice, the doping leads to the formation of a grain boundary of vertices that do not obey the ice rules. In commensurate systems where the ice rules are obeyed, we can introduce random disorder at the individual pinning sites to create regions where vortices may not be able to flip from one side of the trap to another. For weak disorder, all of the vertices still obey the ice rules, while at intermediate levels of disorder we find grain boundaries of vertices which do not obey the ice rules. For strong disorder it is possible to create isolated paired vertices that do not obey the ice rules. In summary, we have shown that an artificial square ice can be created using vortices in a type-II superconductor interacting with a periodic array of pinning sites where each site has a double well potential. By defining the direction of the effective spin according to the side of the double well occupied by the vortex, we find that this system obeys the ice rules for square ice. We add disorder to the system in the form of randomness of the height of the potential barrier at the center of the well, and obtain vertex configurations using a rotating drive protocol which is similar to the shaking ac magnetic field used in nanomagnetic systems. For weak disorder the entire system still obeys the square ice rules. For intermediate disorder, ice-rule breaking vertices appear and form grain boundaries, while for strong disorder there are both gain boundaries and isolated paired defects. In a system with uniform potential barrier heights, we introduce disorder by moving away from commensurability and creating Home pinning sites that contain two or zero vortices. In this case we find grain boundaries that emanate from the defect site and span the sample.

36 MATERIALS SCIENCE↗

Impacts of Ice-Shelf Melting on Water-Mass Transformation in the Southern Ocean from E3SM Simulations

Abstract The Southern Ocean overturning circulation is driven by winds, heat fluxes, and freshwater sources. Among these sources of freshwater, Antarctic sea ice formation and melting play the dominant role. Even though ice-shelf melt is relatively small in magnitude, it is located close to regions of convection, where it may influence dense water formation. Here, we explore the impacts of ice-shelf melting on Southern Ocean water-mass transformation (WMT) using simulations from the Energy Exascale Earth System Model (E3SM) both with and without the explicit representation of melt fluxes from beneath Antarctic ice shelves. We find that ice-shelf melting enhances transformation of Upper Circumpolar Deep Water, converting it to lower density values. While the overall differences in Southern Ocean WMT between the two simulations are moderate, freshwater fluxes produced by ice-shelf melting have a further, indirect impact on the Southern Ocean overturning circulation through their interaction with sea ice formation and melting, which also cause considerable upwelling. We further find that surface freshening and cooling by ice-shelf melting cause increased Antarctic sea ice production and stronger density stratification near the Antarctic coast. In addition, ice-shelf melting causes decreasing air temperature, which may be directly related to sea ice expansion. The increased stratification reduces vertical heat transport from the deeper ocean. Although the addition of ice-shelf melting processes leads to no significant changes in Southern Ocean WMT, the simulations and analysis conducted here point to a relationship between increased Antarctic ice-shelf melting and the increased role of sea ice in Southern Ocean overturning.

Jeong, Hyein↗

Air-sea interactions yielding rapid Beaufort Sea ice losses during the 2021 ONR THINICE Pilot Field Campaign

Seasonal sea ice coverage has declined in the Pacific Arctic region. Losses of the ice cover have modified the region’s surface heat and momentum fluxes providing weather systems more direct interaction with the upper ocean. For example, recent cyclones that have passed over these waters have initiated multiple air-sea interactions and have impacted mixed layer depth, wave properties, and sea ice mass budgets due to diabatic and/or advective processes. As a United States Office of Naval Research (ONR) Departmental Research initiative, one key component of the ONR THINICE program was to advance knowledge on Arctic cyclone coupling with the ocean surface, its ice cover, and understand how such coupling can lead to rapid ice loss. Leading up to the primary field campaign in August 2022, a pilot field campaign from 19 August to 13 September 2021 focused in Utqiagvik, Alaska and Longyearbyen, Svalbard was carried out. This period was marked by frequent Arctic cyclones, periods of strong low-level winds, and stints of extreme short-term Beaufort Sea ice area losses. Cyclones traversed these waters much more frequently than usual during this 26-day period, but did not exhibit extreme central pressures indicative of high intensity and impactful storms. Using ERA5 atmospheric reanalysis fields, CERES and AIRS surface flux retrievals, and in situ sensor data collected from ice-tethered profilers and ice mass balance buoys, we highlight air-sea-ice interactions in the Beaufort Sea during and between these cyclones leading up to extreme ice loss events. Our case study analysis is aimed at understanding how Arctic cyclones, including air-sea interactions prompted by their passage over the marginal ice zone, influence the end-of-summer ice conditions and ice loss events. This study provides an example where frequent, yet weak storms drive rather large marginal sea-scale losses albeit with heterogenous sea ice effects at local scales.

Ballinger, Thomas [International Arctic Research C↗

Complex plant-derived organic aerosol as ice-nucleating particles – more than the sums of their parts?

Quantifying the impact of complex organic particles on the formation of ice crystals in clouds remains challenging, mostly due to the vast number of different sources ranging from sea spray to agricultural areas. In particular, there are many open questions regarding the ice nucleation properties of organic particles released from terrestrial sources such as decaying plant material. In this work, we present results from laboratory studies investigating the immersion freezing properties of individual organic compounds commonly found in plant tissue and complex organic aerosol particles from vegetated environments, without specifically investigating the contribution from biological particles, which may contribute to the overall ice nucleation efficiency observed at high temperatures. To characterize the ice nucleation properties of plant-related aerosol samples for temperatures between 242 and 267 K, we used the Aerosol Interaction and Dynamics in the Atmosphere (AIDA) cloud chamber and the Ice Nucleation SpEctrometer of the Karlsruhe Institute of Technology (INSEKT), which is a droplet freezing assay. Individual plant components (polysaccharides, lignin, soy and rice protein) were mostly less ice active, or similarly ice active, compared to microcrystalline cellulose, which has been suggested by recent studies to be a proxy for quantifying the primary cloud ice formation caused by particles originating from vegetation. In contrast, samples from ambient sources with a complex organic matter composition (agricultural soils and leaf litter) were either similarly ice active or up to 2 orders of magnitude more ice active than cellulose. Of all individual organic plant components, only carnauba wax (i.e., lipids) showed a similarly high ice nucleation activity as that of the samples from vegetated environments over a temperature range between 245 and 252 K. Hence, based on our experimental results, we suggest considering cellulose as being representative for the average ice nucleation activity of plant-derived particles, whereas lignin and plant proteins tend to provide a lower limit. In contrast, complex biogenic particles may exhibit ice nucleation activities which are up to 2 orders of magnitude higher than observed for cellulose, making ambient plant-derived particles a potentially important contributor to the population of ice-nucleating particles in the troposphere, even though major uncertainties regarding their transport to cloud altitude remain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evaluate the application of ERTS-A data for detecting and mapping sea ice

The author has identified the following significant results. The results of the analysis of data collected during the spring and summer demonstrate that ERTS-1 imagery has a high potential for monitoring arctic sea ice conditions during the time for maximum ice extent through ice-breakup season. In the eastern Beaufort Sea area, the combination of ERTS-1 orbital overlap and a high incidence of cloud-free conditions during the spring assures a high frequency of repetitive satellite coverage. In the mid-Beaufort Sea, numerous fractures and leads can be identified, even in the early spring data. Ice features that can be identified include: development of fractures leading to the formation of distinct ice floes; growth and deterioration of leads; evidence of shearing movements of ice masses; formation of new grey ice within leads; distinction between grey, grey-white, and older forms of ice; and the deterioration of the ice surface evidenced by the formation of puddles, thaw holes, and drainage patterns. Ice conditions in the Bering Sea near St. Lawrence Island reported by aircraft observers participating in the Bering Sea Expedition are in close agreement with the ice conditions mapped from the corresponding ERTS-1 imagery. Ice features identified were: boundaries between grey ice and first year ice, shear leads, and occurrence of open water.

Barnes, J. C.↗

Volcanic ash layers in blue ice fields (Beardmore Glacier Area, Antarctica): Iridium enrichments

Dust bands on blue ice fields in Antarctica have been studied and have been identified to originate from two main sources: bedrock debris scraped up from the ground by the glacial movement (these bands are found predominantly at fractures and shear zones in the ice near moraines), and volcanic debris deposited on and incorporated in the ice by large-scale eruptions of Antarctic (or sub-Antractic) volcanoes. Ice core studies have revealed that most of the dust layers in the ice cores are volcanic (tephra) deposits which may be related to some specific volcanic eruptions. These eruptions have to be related to some specific volcanic eruptions. These eruptions have to be relatively recent (a few thousand years old) since ice cores usually incorporate younger ice. In contrast, dust bands on bare blue ice fields are much older, up to a few hundred thousand years, which may be inferred from the rather high terrestrial age of meteorites found on the ice and from dating the ice using the uranium series method. Also for the volcanic ash layers found on blue ice fields correlations between some specific volcanoes (late Cenozoic) and the volcanic debris have been inferred, mainly using chemical arguments. During a recent field expedition samples of several dust bands found on blue ice fields at the Lewis Cliff Ice Tongue were taken. These dust band samples were divided for age determination using the uranium series method, and chemical investigations to determine the source and origin of the dust bands. The investigations have shown that most of the dust bands found at the Ice Tongue are of volcanic origin and, for chemical and petrological reasons, may be correlated with Cenozoic volcanoes in the Melbourne volcanic province, Northern Victoria Land, which is at least 1500 km away. Major and trace element data have been obtained and have been used for identification and correlation purposes. Recently, some additional trace elements were determined in some of the dust band samples, including Ir. Iridium determinations were made using INAA, with synthetical and natural (meteorite) standards. These findings are discussed.

Koeberl, Christian↗

A scheme for parameterizing ice-cloud water content in general circulation models

The optical properties of ice clouds are a primary issue for climate and climate change. Evaluating these optical properties in three-dimensional models for studying climate will require a method to calculate the ice water content of such clouds. A procedure is developed to parameterize ice water content as a function of large-scale meteorological characteristics for use in circulation models in which the ice water content is not calculated by means of a three-dimensional prognostic equation for condensed water. The technique identifies large-scale flows in which ice clouds exist and calculates their ice water content by reconstructing the trajectory associated with cloud formation. As the cloud forms, its ice content changes both by deposition of ice from water vapor and by ice removal by sedimentation. The sedimentation process is found to modify significantly the ice water content expected from deposition alone. Ice water contents predicted by the parameterization are compared with aircraft observations collected in the middle latitudes and the tropics, and show reasonable agreement over four orders-of-magnitude of ice water content. A parameterization for the sublimation of ice crystals settling into ice-subsaturated environments is also presented.

Heymsfield, Andrew J.↗

Ocean interactions with the base of Amery Ice Shelf, Antarctica

Using a two-dimensional ocean themohaline circulation model, we varied the cavity shape beneath Amery Ice Shelf in an attempt to reproduce the 150-m-thick marine ice layer observed at the 'G1' ice core site. Most simulations caused melting rates which decrease the ice thickness by as much as 400 m between grounding line and G1, but produce only minor accumulation at the ice core site and closer to the ice front. Changes in the sea floor and ice topographies revealed a high sensitivity of the basal mass balance to water column thickness near the grounding line, to submarine sills, and to discontinuities in ice thickness. Model results showed temperature/salinity gradients similar to observations from beneath other ice shelves where ice is melting into seawater. Modeled outflow characteristics at the ice front are in general agreement with oceanographic data from Prydz Bay. We concur with Morgan's inference that the G1 core may have been taken in a basal crevasse filled with marine ice. This ice is formed from water cooled by ocean/ice shelf interactions along the interior ice shelf base.

Hellmer, Hartmut H.↗

On evaluating the accuracy of SAR sea-ice classification using multifrequency polarimetric AIRSAR data

We investigate how multifrequency and polarimetric synthetic aperture radar (SAR) imagery enhances present capability to discriminate different ice conditions in single-frequency, single-polarization satellite SAR data. Frequencies considered are C- (lambda = 5.6cm), L- (lambda = 24cm) and P- (lambda = 68cm) band. Radar backscatter characteristics of six radiometrically and polarimetrically distinct ice types are selected from a cluster analysis of the multifrequency polarimetric SAR data and used to classify SAR images. Validation of these ice conditions is based on information provided by aerial photos, weather and ice surface measurements acquired at an ice camp, together with airborne passive microwave imagery, and visual analysis of the SAR data. The six identified sea-ice types are: (1) multiyear sea-ice; (2) compressed first year ice; (3) first year rubble and ridges; (4) first year rough ice; (5) first year smooth ice; and (6) thin ice. Open water is absent in all analyzed data. Classification of the SAR imagery into those six ice types is performed using a Bayesian Maximum A Posteriori classifier. Two complete scenes acquired at different dates in different locations are classified. The scenes were chosen such that they are representative of typical ice conditions in the Beaufort Sea in March 1988 and because ancillary information is available for validating the segmentation of various ice surface conditions.

Drinkwater, Mark R.↗

Probing the structure of cometary ice

Computer simulations of bulk and vapor deposited amorphous ices are presented. The structure of the bulk low density amorphous ice is in good agreement with experiments on pressure disordered amorphous ice. Both the low density bulk ice and the vapor deposited ices exhibit strong ordering. Vapor deposition of hot (300 K) water molecules onto a cold (77 K) substrate yields less porous ices than deposition of cold (77 K) water molecules onto a cold substrate. Both vapor deposited ices are more porous than the bulk amorphous ice. The structure of bulk high density amorphous ice is only in fair agreement with experimental results. Attempts to simulate high density amorphous ice via vapor deposition were not successful. Electron diffraction results on vapor deposited amorphous ice indicate that the temperature of the nucleation of the cubic phase depends upon the amount of time between the deposition and the onset of crystallization, suggesting that freshly deposited ice layers reconstruct on time of the order of hours. The temperature dependence of the microporosity of the vapor deposited amorphous ices might affect laboratory experiments that are aimed at simulating astrophysical ices in the context of the origin of prebiotic organic material and its transport to the Earth.

Wilson, Michael A.↗

Trends in the Length of the Southern Ocean Sea Ice Season: 1979-1999

Satellite data can be used to observe the sea ice distribution around the continent of Antarctica on a daily basis and hence to determine how many days a year have sea ice at each location. This has been done for each of the 21 years 1979-1999. Mapping the trends in these data over the 21-year period reveals a detailed pattern of changes in the length of the sea ice season around Antarctica. Most of the Ross Sea ice cover has undergone a lengthening of the sea ice season, whereas most of the Amundsen Sea ice cover and almost the entire Bellingshausen Sea ice cover have undergone a shortening of the sea ice season. Results around the rest of the continent, including in the Weddell Sea, are more mixed, but overall, more of the Southern Ocean experienced a lengthening of the sea ice season than a shortening. For instance, the area experiencing a lengthening of the sea ice season by at least 1 day per year is 5.8 x 10(exp 6) sq km, whereas the area experiencing a shortening of the sea ice season by at least 1 day per year is less than half that, at 2.8 x 10(exp 6) sq km. This contrasts sharply with what is happened over the same period in the Arctic, where, overall, there has been some depletion of the ice cover, including shortened sea ice seasons and decreased ice extents.

Parkinson, Claire L.↗

Variability of Antarctic Sea Ice 1979-1998

The principal characteristics of the variability of Antarctic sea ice cover as previously described from satellite passive-microwave observations are also evident in a systematically-calibrated and analyzed data set for 20.2 years (1979-1998). The total Antarctic sea ice extent (concentration > 15 %) increased by 13,440 +/- 4180 sq km/year (+1.18 +/- 0.37%/decade). The area of sea ice within the extent boundary increased by 16,960 +/- 3,840 sq km/year (+1.96 +/- 0.44%/decade). Regionally, the trends in extent are positive in the Weddell Sea (1.5 +/- 0.9%/decade), Pacific Ocean (2.4 +/- 1.4%/decade), and Ross (6.9 +/- 1.1 %/decade) sectors, slightly negative in the Indian Ocean (-1.5 +/- 1.8%/decade, and strongly negative in the Bellingshausen-Amundsen Seas sector (-9.5 +/- 1.5%/decade). For the entire ice pack, small ice increases occur in all seasons with the largest increase during autumn. On a regional basis, the trends differ season to season. During summer and fall, the trends are positive or near zero in all sectors except the Bellingshausen-Amundsen Seas sector. During winter and spring, the trends are negative or near zero in all sectors except the Ross Sea, which has positive trends in all seasons. Components of interannual variability with periods of about 3 to 5 years are regionally large, but tend to counterbalance each other in the total ice pack. The interannual variability of the annual mean sea-ice extent is only 1.6% overall, compared to 5% to 9% in each of five regional sectors. Analysis of the relation between regional sea ice extents and spatially-averaged surface temperatures over the ice pack gives an overall sensitivity between winter ice cover and temperature of -0.7% change in sea ice extent per K. For summer, some regional ice extents vary positively with temperature and others negatively. The observed increase in Antarctic sea ice cover is counter to the observed decreases in the Arctic. It is also qualitatively consistent with the counterintuitive prediction of a global atmospheric-ocean model of increasing sea ice around Antarctica with climate warming due to the stabilizing effects of increased snowfall on the Southern Ocean.

Zwally, H. Jay↗

Onset of Convection in Ice I with Composite Newtonian and Non-Newtonian Rheology: Application to the Icy Galilean Satellites

Ice I exhibits a complex rheology at temperature and pressure conditions appropriate for the interiors of the ice I shells of Europa, Ganymede, and Callisto. We use numerical methods and existing parameterizations of the critical Rayleigh number to determine the conditions required to trigger convection in an ice I shell with the stress-, temperature- and grain size- dependent rheology measured in laboratory experiments by Goldsby and Kohlstedt [2001]. The critical Rayleigh number depends on the ice grain size and the amplitude and wavelength of temperature perturbation issued to an initially conductive ice I shell. If the shells have an assumed uniform grain size less than 0.4 mm, deformation during initial plume growth is accommodated by Newtonian volume diffusion. If the ice grain size is between 0.4 mm and 3 cm, deformation during plume growth is accommodated by weakly non-Newtonian grain boundary sliding, where the critical ice shell thickness for convection depends on the amplitude of temperature perturbation to the _0.5 power. If the ice grain size exceeds 2 cm, convection can not occur in the ice I shells of the Galilean satellites regardless of the amplitude or wavelength of temperature perturbation. If the grain size in a convecting ice I shell evolves to effective values greater than 2 cm, convection will cease. If the ice shell has a grain size large enough to permit flow by dislocation creep, the ice is too stiff to permit convection, even in the thickest possible ice I shell. Consideration of the composite rheology implies that estimates of the grain size in the satellites and knowledge of their initial thermal states are required when judging the convective instability of their ice I shells.

Barr, A. C.↗

Forces Generated by High Velocity Impact of Ice on a Rigid Structure

Tests were conducted to measure the impact forces generated by cylindrical ice projectiles striking a relatively rigid target. Two types of ice projectiles were used, solid clear ice and lower density fabricated ice. Three forms of solid clear ice were tested: single crystal, poly-crystal, and "rejected" poly-crystal (poly-crystal ice in which defects were detected during inspection.) The solid ice had a density of approximately 56 lb/cu ft (0.9 gm/cu cm). A second set of test specimens, termed "low density ice" was manufactured by molding shaved ice into a cylindrical die to produce ice with a density of approximately 40 lb/cu ft (0.65 gm/cu cm). Both the static mechanical characteristics and the crystalline structure of the ice were found to have little effect on the observed transient response. The impact forces generated by low density ice projectiles, which had very low mechanical strength, were comparable to those of full density solid ice. This supports the hypothesis that at a velocity significantly greater than that required to produce fracture in the ice, the mechanical properties become relatively insignificant, and the impact forces are governed by the shape and mass of the projectile.

Pereira, J. Michael↗