Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Flow Visualization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Mass and momentum turbulent transport experiments with confined swirling coaxial jets. I

An experimental study of mixing downstream of swirling coaxial jets discharging into an expanded duct was conducted to obtain data for the evaluation and improvement of turbulent transport models currently used in a variety of computational procedures throughout the combustion community. A combination of laser velocimeter and laser induced fluorescence techniques was employed to obtain mean and fluctuating velocity and concentration distributions which were used to derive mass and momentum turbulent transport parameters currently incorporated into various combustor flow models. Flow visualization techniques were also employed to determine qualitatively the time dependent characteristics of the flow and the scale of turbulence. Mean and fluctuating velocity profiles and probability density functions were obtained at selected axial and radial locations throughout the flow field. Mixing occurred in several steps of axial and radial mass transport and was coupled with a large radial mean convective flux. Major mixing regions were observed to occur (1) at the interface between the inner stream and the centerline recirculation zone, and (2) at the interface between the inner jet and the annular jet streams. Mixing for swirling flow was completed in one-third the length required for nonswirling flow.

Johnson, B. V.↗
NASA NTRS1984

Flow in sigmoid diffusers of moderate curvature

Developing laminar and turbulent flows have been measured in two diffusers with S- and C-shaped center-lines, small divergence angle and moderate curvature. The square inlet cross-section expanded in the plane of curvature to a rectangle with an exit-to-inlet area ratio of 1.5. Laser-Doppler anemometry was used to measure three velocity components and, in turbulent flow, the associated fluctuations and cross-correlations. Wall static pressure measurements are also reported. Flow visualization did not reveal the presence of any recirculation regions. Pressure-driven secondary flows are present in both ducts, but are generally smaller than those measured in similar ducts of uniform cross-section area.

Rojas, J.↗
NASA NTRS1985

Optical interferometry in fluid dynamics research

Optical interferometry techniques have been applied to the investigation of transonic airfoil flow fields in large-scale wind tunnels. Holographic interferometry techniques were used in the study of two-dimensional symmetric NACA 64A010 and Douglas Aircraft Company DSMA671 supercritical airfoil performance in the NASA Ames 2 ft x 2 ft transonic wind tunnel. Quantitative data obtained from the interferograms were compared to the surface pressure data. The excellent agreement obtained verified the accuracy of the flow visualization and demonstrated the potential for acquiring quantitative scalar results. Measurements of the inviscid flow speed and the boundary layer and wake velocity profiles were extracted from the interferograms and compared to laser Doppler velocimeter measurements. These results were also in good agreement. A method for acquiring real-time interferometric data in large-scale facilities was developed. This method, based on the point diffraction interferometer, was successfully tested in the Ames 2 ft x 2 ft transonic wind tunnel. The holographic and real-time interferometry methods were applied to the investigations of circulation control airfoils utilizing the Coanda effect. These results revealed the details of the jet interaction with the trailing edge boundary layer and the other parameters affecting the lift augmentation.

Bachalo, W. D.↗
NASA NTRS1985

An assessment of some vorticity field-leading edge interactions

A review is undertaken of some recent advances in the following areas: the encounter of distributed and concentrated vorticity at a single frequency with a leading-edge, the interaction of multiple concentrations of vorticity with an edge, the distortion due to finite scale and angle of attack of the leading-edge, and the penetration of the leading-edge interaction into the near-wake region. Time-sequence flow visualization and phase-coordinated pressure measurements provide physical insight into the mechanisms of flow distortion and loading. Promising paths for future research are suggested on the basis of recent progress.

Rockwell, D.↗
NASA NTRS1986

Mass and momentum turbulent transport experiments with swirling confined coaxial jets. II

An experimental study of mixing downstream of swirling coaxial jets discharging into an expanded duct was conducted to obtain data for the evaluation and improvement of turbulent transport models currently used in a variety of computational procedures throughout the combustion community. A combination of laser velocimeter and laser induced fluorescence techniques was employed to obtain mean and fluctuating velocity and concentration distributions at selected axial and radial locations throughout the flow field. Flow visualization techniques were also employed to determine qualitatively the time dependent characteristics of the flow and the scale of turbulence. Simultaneous two component velocity and concentration/velocity measurements provided data which were used to determine the average momentum and mass transport rates for each of three measurement planes. Mixing for swirling flows occurred in several steps of axial and radial mean convective flow and was completed in one-third the length required for nonswirling flow. Comparison of the mass and momentum transport processes for swirling and nonswirling flows indicated that large differences existed in these processes between the two flows.

Roback, R.↗
NASA NTRS1986

Forebody vortex management for yaw control at high angles of attack

The yaw-control potential of deployable forebody strakes at angles of attack above the range of conventional rudder effectiveness has been investigated. The conformally-stored strakes when deployed force asymmetrical vortex shedding from the forebody, thereby generating a controlled yawing moment. The concept was explored through low-speed wind tunnel tests on a conical forebody in isolation and in a generic fighter configuration. Force and moment measurements on the complete model were supplemented with circumferential pressure and flow-visualization surveys on an isolated forebody, in order to gain insight into the vortex flow mechanisms resulting from forced asymmetrical separations and to quantify the obtainable yaw power at angles of attack to 80 deg. This preliminary, low-Reynolds-number study showed asymmetrically-deployed forebody strakes to have considerable yaw control potential, whose sensitivity to scale effects needs further investigation.

Rao, D. M.↗
NASA NTRS1987

Optical interferometry in fluid dynamics research

Optical interferometry techniques were applied to the investigation of transonic airfoil flow fields in large wind tunnels. Holographic interferometry techniques were used to study 2 dimensional symmetric NACA 64A010 and Douglas Aircraft Co. DSMA671 supercritical airfoil performance in the NASA Ames 2 x 2 ft transonic wind tunnel. Quantitative data obtained from the interferograms were compared to the surface pressure data. The agreement obtained verified the accuracy of the flow visualization and demonstrated the potential for acquiring quantitative scalar results. Measurements of the inviscid flow speed and the boundary layer and wake velocity profiles were extracted from the interferograms and compared to laser Doppler velocimeter measurements. These results were also in good agreement. A method for acquiring real time interferometric data in large scale facilities was developed. This method, based on the point diffraction interferometer, was successfully tested in the 2 x 2 ft transonic wind tunnel. The holographic and real time interferometry methods were applied to the investigations of circulation control airfoils utilizing the Coanda effect. These results reveals the details of the jet interacting with the trailing edge boundary layer and the other parameters affecting the lift augmentation.

Bachalo, W. D.↗
NASA NTRS1989

Flow-field characteristics and normal-force correlations for delta wings from Mach 2.4 to 4.6

An experimental investigation has been conducted to determine the upper-surface flowfield types and the normal-force characteristics of a series of delta wing models at supersonic speeds. Flow-visualization data were used to classify the flowfields into seven primary types: shockless attached flow, separation bubble, classical vortex, vortex with shock, shock with no separation, shock-induced separation, and separation bubble with shock. The pressure distributions were integrated to obtain upper and lower surface normal-force loadings. A minimal effect of sweep was observed on the upper-surface normal force at constant Mach number and a minimal effect of Mach number was noted for the 75 deg delta wing lower-surface normal force. The normal-force coefficients for all test conditions were correlated, and a single empirical equation was formulated from which the normal-force coefficient could be calculated as a function of Mach number, angle of attack, and wing aspect ratio.

Covell, Peter F.↗
NASA NTRS1991

Experimental and analytical studies of flow through a ventral and axial exhaust nozzle system for STOVL aircraft

Flow through a combined ventral and axial exhaust nozzle system was studied experimentally and analytically. The work is part of an ongoing propulsion technology effort at NASA Lewis Research Center for short takeoff, vertical landing (STOVL) aircraft. The experimental investigation was done on the NASA Lewis Powered Lift Facility. The experiment consisted of performance testing over a range of tailpipe pressure ratios from 1 to 3.2 and flow visualization. The analytical investigation consisted of modeling the same configuration and solving for the flow using the PARC3D computational fluid dynamics program. The comparison of experimental and analytical results was very good. The ventral nozzle performance coefficients obtained from both the experimental and analytical studies agreed within 1.2 percent. The net horizontal thrust of the nozzle system contained a significant reverse thrust component created by the flow overturning in the ventral duct. This component resulted in a low net horizontal thrust coefficient. The experimental and analytical studies showed very good agreement in the internal flow patterns.

Esker, Barbara S.↗
NASA NTRS1991

Experimental and analytical studies of flow through a ventral and axial exhaust nozzle system for STOVL aircraft

Flow through a combined ventral and axial exhaust nozzle system was studied experimentally and analytically. The work is part of an ongoing propulsion technology effort at NASA Lewis Research Center for short takeoff, vertical landing (STOVL) aircraft. The experimental investigation was done on the NASA Lewis Powered Lift Facility. The experiment consisted of performance testing over a range of tailpipe pressure ratios from 1 to 3.2 and flow visualization. The analytical investigation consisted of modeling the same configuration and solving for the flow using the PARC3D computational fluid dynamics program. The comparison of experimental and analytical results was very good. The ventral nozzle performance coefficients obtained from both the experimental and analytical studies agreed within 1.2 percent. The net horizontal thrust of the nozzle system contained a significant reverse thrust component created by the flow overturning in the ventral duct. This component resulted in a low net horizontal thrust coefficient. The experimental and analytical studies showed very good agreement in the internal flow patterns.

Esker, Barbara S.↗
NASA NTRS1991

A numerical and experimental study of tangential jet blowing applied to bodies at high angles of attack

The effects of tangential jet blowing on the vortical structures developing about the fuselage of a missile or aircraft at high angle of attack are investigated numerically and experimentally. Computations are carried out for fully laminar and fully turbulent flows, and the results are compared with flow visualization data. It is shown that turbulent computations are more accurate in describing the flow behavior. The actuator plane method is shown to be sufficiently accurate in modeling the essential flow physics of a tangential jet.

Font, G. I.↗
NASA NTRS1992

Aerodynamics of a finite wing with simulated ice

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional wing is studied experimentally. Results are reviewed from earlier two-dimensional tests which show the character of the large leading-edge separation bubbles caused by the simulated ice accretion. The 2-D bubbles are found to closely resemble well known airfoil laminar separation bubbles. For the 3-D experiments a semispan wing of effective aspect ratio five was mounted from the sidewall of the UIUC subsonic wind tunnel. The model uses a NACA 0012 airfoil section on a rectangular planform with interchangeable tip and root sections to allow for 0- and 30-degree sweep. A three-component sidewall balance was used to measure lift, drag and pitching moment on the clean and iced model. Fluorescent oil flow visualization has been performed on the iced model and reveals extensive spanwise and vortical flow in the separation bubble aft of the upper surface horn. Sidewall interaction and spanwise nonuniformity are also seen on the unswept model. Comparisons to the computed flow fields are shown. Results are also shown for roughness effects on the straight wing. Sand grain roughness on the ice shape is seen to have a different effect than isolated 3-D roughness elements.

Bragg, M. B.↗
NASA NTRS1993

Investigation of a strut/endwall interaction in supersonic annular flow

A combined experimental and numerical investigation of strut/endwall interactions within an annular duct having a supersonic core flow has been conducted. Four diamond-shaped struts with a 7 deg half angle were positioned circumferentially equidistant within an annular duct having a gap height of 0.7 strut chords, and an inner-to-outer wall radius ratio of 0.7. Turbulent boundary layers exist on both inner and outer walls of the duct, but have not merged. The core flow upstream of the struts is uniform at a nominal Mach number of 3.0 and a Reynolds number of 3 x 10 exp 5 based on the strut chord length. Experimental results, which include Pitot pressure distributions within the flow field, static pressure distributions on the inner and outer walls of the duct, and oil flow visualization on the centerbody and strut, are presented and compared with CFD predictions. Secondary flows associated with the interactions are examined including the trajectories of the horseshoe vortices formed at the leading and trailing edges of the strut and the trajectories of the vortices formed in the corner of the strut/endwall intersection.

Williams, K. E.↗
NASA NTRS1996

Ground Based Studies of Thermocapillary Flows in Levitated Drops

Ground-based experiments together with analytical studies are presently being conducted for levitated drops. Both acoustic and electrostatic techniques are being employed to achieve levitation of drops in a gaseous environment. The scientific effort is principally on the thermal and the fluid phenomena associated with the local heating of levitated drops, both at 1-g and at low-g. In particular, the thermocapillary flow associated with local spot heating is being studied. Fairly stable acoustic levitation of drops has been achieved with some exceptions when random rotational motion of the drop persists. The flow visualization has been carried out by light scattering from smoke particles for the exterior flow and fluorescent tracer particles in the drop. The results indicate a lack of axial symmetry in the internal flow even though the apparatus and the heating are symmetric. The theoretical studies for the past year have included fundamental analyses of acoustically levitated spherical drops. The flow associated with a particle near the velocity antinode is being investigated by the singular perturbation technique. As a first step towards understanding the effect of the particle displacement from the antinode, the flow field about the node has been calculated for the first time. The effect of the acoustic field on the interior of a liquid drop has also been investigated. The results predict that the internal flow field is very weak.

Sadhal, Satwindar Singh↗
NASA NTRS2002

Parametric Study of a YAV-8B Harrier in Ground Effect using Time-Dependent Navier-Stokes Computations

A process is described which enables the generation of 35 time-dependent viscous solutions for a YAV-8B Harrier in ground effect in one week. Overset grids are used to model the complex geometry of the Harrier aircraft and the interaction of its jets with the ground plane and low-speed ambient flow. The time required to complete this parametric study is drastically reduced through the use of process automation, modern computational platforms, and parallel computing. Moreover, a dual-time-stepping algorithm is described which improves solution robustness. Unsteady flow visualization and a frequency domain analysis are also used to identify and correlated key flow structures with the time variation of lift.

Pandya, Shishir↗
NASA NTRS1979

Low-turbulence high-speed wind tunnel for the determination of cascade shock losses

A low turbulence high-speed wind tunnel, using anti-turbulence screening and a 100:1 contraction ratio, has been found suitable for high-speed smoke flow visualization. The location and strength of normal, oblique, and curved shock waves generated by transonic or supersonic wind tunnel flow over airfoils or through axial compressor cascades is determined by combined shadowgraph and smokelines visualization techniques without the interference effects caused by intrusive probes. The Reynolds number based on chord varied between 50,000 and 1,000,000. Preliminary results are compared with the relevant theory and data gathered using a total pressure probe.

Slovisky, J. A.↗
NASA NTRS1993

Colorimetric qualification of shear sensitive liquid crystal coatings

The work that has been done to date on the Shear Sensitive Liquid Crystal Project demonstrated that cholesteric liquid crystal coatings respond to both the direction and magnitude of a shearing force. The response of the coating is to selectively scatter incident white light into a spectrum of colors. Discernible color changes at a fixed angle of observation and illumination are the result of an applied shear stress. The intention was to be able to convert these observable color patterns from a flow visualization technique into a quantitative tool. One of the earlier intentions was to be able to use liquid crystals in dynamic flow fields. This was assumed possible because liquid crystals had made it possible to visualize transients in surface shear forces. Although the transients were visualized by color changes to an order one micro second, the time response of a coating to align to a shearing force is dependent on the magnitude of the change between its initial and final states. Unfortunately, the response is not instantaneous. It is for this reason any future attempt at quantifying the magnitude and directions of a shearing force are limited to surface shear stress vector fields in three dimensional steady state flows. This limitation does not significantly detract from the utility of liquid crystal coatings. The measurement of skin friction in the study of transition on wings, prediction of drag forces, performance assessment, and the investigation of boundary layer behavior is of great importance in aerodynamics. There exist numerous examples of techniques for the measurement of surface shear stress. Most techniques require arduous calibrations and necessitate extensive preparation of the receiving surfaces. However, the main draw back of instruments such as Preston tubes, hot films, buried wire gages, and floating element balances is that they only provide a point measurement. The advantages of capturing global shear data would be appreciable when compared with conventional point measurement sensors. It has yet to be determined if a repeatable correlation exists between the measured color of a liquid crystal coating and the magnitude/directional components of a shear vector imposed onto it.

Muratore, Joseph J., Jr.↗
NASA NTRS2000

Visualization, Extraction and Quantification of Discontinuities in Compressible Flows

Scientific visualizations of two-dimensional compressible flow of a gas with discontinuities are presented. The numerical analogue to experimental techniques such as schlieren imaging, shadowgraphs, and interferograms are discussed. Edge detection techniques are utilized to identify the discontinuities. In particular, the zero crossing of the Laplacian of a field (usually density) is recommended for extracting the discontinuities. An algorithm to extract and quantify the discontinuities is presented. To illustrate the methods developed in the report, the example chosen is that of an unsteady interaction of a shock wave with a contact discontinuity.

Samtaney, Ravi↗