Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engineering - Particle accelerators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

High variable mixture ratio oxygen/hydrogen engine

The ability of an O2/H2 engine to operate over a range of high-propellant mixture ratios was previously shown to be advantageous in single stage to orbit (SSTO) vehicles. The results are presented for the analysis of high-performance engine power cycles operating over propellant mixture ratio ranges of 12 to 6 and 9 to 6. A requirement to throttle up to 60 percent of nominal thrust was superimposed as a typical throttle range to limit vehicle acceleration as propellant is expended. The object of the analysis was to determine areas of concern relative to component and engine operability or potential hazards resulting from the operating requirements and ranges of conditions that derive from the overall engine requirements. The SSTO mission necessitates a high-performance, lightweight engine. Therefore, staged combustion power cycles employing either dual fuel-rich preburners or dual mixed (fuel-rich and oxygen-rich) preburners were examined. Engine mass flow and power balances were made and major component operating ranges were defined. Component size and arrangement were determined through engine layouts for one of the configurations evaluated. Each component is being examined to determine if there are areas of concern with respect to component efficiency, operability, reliability, or hazard. The effects of reducing the maximum chamber pressure were investigated for one of the cycles.

Erickson, C. M.↗
NASA NTRS1997

Lunar and Planetary Missions Launched from a Geosynchronous Transfer Orbit

Lithium Lorentz Force Accelerators (LFA's) are capable of processing very high power levels and are therefore applicable to a wide range of challenging missions. For this class of missions, the emphasis must be on achieving high efficiency at an Isp of 4000-5000s at power levels of 200-250 kWe. The engines must demonstrate very reliable operation for a service life of about 3000 hours.

Lithium↗
DOE OSTI2025

Structure and ultrafast dynamics of tri-nuclear Ag-/Tl–Pt 2 POP 4 complexes in solution

The energetics and dynamics of ion assembly in solution has broad influence in nanomaterials and inorganic synthesis. To investigate the fundamental processes involved, we present a time-resolved x-ray solution scattering (TR-XSS) study of the trinuclear silver and thallium complexes of the diplatinum ion PtPOP [Pt 2 (H 2 P 2 O 5 )$_4^{4−}$] in aqueous solution. These complexes, their structural properties, and their electronic structure are not well understood and afford a unique opportunity to study the metal–metal bond formation that influences molecular and material assembly in solution. We present model-independent analysis of the observed dynamics as well as an analysis incorporating time-resolved structural refinements of key bond lengths with $<$100 fs time resolution. We find that upon photoexcitation, the Pt atoms contract ∼0.25 Å toward the center of both the Ag- and the Tl-PtPOP complexes, as previously observed for the PtPOP anion. For the AgPtPOP system, an ultrafast Ag-Pt bond expansion of ∼0.2 Å is observed, whereas in contrast, the TlPtPOP system exhibits a Tl-Pt bond contraction of ∼0.3 Å upon photoexcitation. For both complexes, the change in electronic state leads to coherent (“wave-packet”) oscillations along the metal–Pt coordinates. Based on these structural dynamics, we propose an electronic structure model that describes the metal–metal bonding behavior in both the ground and excited state for both complexes.

Lenzen, Philipp [Technical Univ. of Denmark, Lyngb↗
NASA NTRS2017

Using Model-Based Systems Engineering to Provide Artifacts for NASA Project Life-cycle and Technical Reviews

This paper is for the AIAA Space Conference. The ability of systems engineers to use model-based systems engineering (MBSE) to generate self-consistent, up-to-date systems engineering products for project life-cycle and technical reviews is an important aspect for the continued and accelerated acceptance of MBSE. Currently, many review products are generated using labor-intensive, error-prone approaches based on documents, spreadsheets, and chart sets; a promised benefit of MBSE is that users will experience reductions in inconsistencies and errors. This work examines features of SysML that can be used to generate systems engineering products. Model elements, relationships, tables, and diagrams are identified for a large number of the typical systems engineering artifacts. A SysML system model can contain and generate most systems engineering products to a significant extent and this paper provides a guide on how to use MBSE to generate products for project life-cycle and technical reviews. The use of MBSE can reduce the schedule impact usually experienced for review preparation, as in many cases the review products can be auto-generated directly from the system model. These approaches are useful to systems engineers, project managers, review board members, and other key project stakeholders.

MBSE↗
NASA NTRS2017

Using Model-Based Systems Engineering To Provide Artifacts for NASA Project Life-Cycle and Technical Reviews

The ability of systems engineers to use model-based systems engineering (MBSE) to generate self-consistent, up-to-date systems engineering products for project life-cycle and technical reviews is an important aspect for the continued and accelerated acceptance of MBSE. Currently, many review products are generated using labor-intensive, error-prone approaches based on documents, spreadsheets, and chart sets; a promised benefit of MBSE is that users will experience reductions in inconsistencies and errors. This work examines features of SysML that can be used to generate systems engineering products. Model elements, relationships, tables, and diagrams are identified for a large number of the typical systems engineering artifacts. A SysML system model can contain and generate most systems engineering products to a significant extent and this paper provides a guide on how to use MBSE to generate products for project life-cycle and technical reviews. The use of MBSE can reduce the schedule impact usually experienced for review preparation, as in many cases the review products can be auto-generated directly from the system model. These approaches are useful to systems engineers, project managers, review board members, and other key project stakeholders.

SE Product↗
DOE OSTI2025

Machine Learning-Driven Conservative-to-Primitive Conversion in Hybrid Piecewise Polytropic and Tabulated Equations of State

We present a novel machine learning (ML)-based method to accelerate conservative-to-primitive inversion, focusing on hybrid piecewise polytropic and tabulated equations of state. Traditional root-finding techniques are computationally expensive, particularly for large-scale relativistic hydrodynamics simulations. To address this, we employ feedforward neural networks (NNC2PS and NNC2PL), trained in PyTorch (2.0+) and optimized for GPU inference using NVIDIA TensorRT (8.4.1), achieving significant speedups with minimal accuracy loss. The NNC2PS model achieves 𝐿 1 and 𝐿 ∞ errors of 4.54 × 10 −7 and 3.44 × 10−6, respectively, while the NNC2PL model exhibits even lower error values. TensorRT optimization with mixed-precision deployment substantially accelerates performance compared to traditional root-finding methods. Specifically, the mixed-precision TensorRT engine for NNC2PS achieves inference speeds approximately 400 times faster than a traditional single-threaded CPU implementation for a dataset size of 1,000,000 points. Ideal parallelization across an entire compute node in the Delta supercomputer (dual AMD 64-core 2.45 GHz Milan processors and 8 NVIDIA A100 GPUs with 40 GB HBM2 RAM and NVLink) predicts a 25-fold speedup for TensorRT over an optimally parallelized numerical method when processing 8 million data points. Moreover, the ML method exhibits sub-linear scaling with increasing dataset sizes. We release the scientific software developed, enabling further validation and extension of our findings. By exploiting the underlying symmetries within the equation of state, these findings highlight the potential of ML, combined with GPU optimization and model quantization, to accelerate conservative-to-primitive inversion in relativistic hydrodynamics simulations.

conservative-to-primitive conversion↗
NASA NTRS1998

Simulation of Crack Propagation in Engine Rotating Components under Variable Amplitude Loading

The crack propagation life of tested specimens has been repeatedly shown to strongly depend on the loading history. Overloads and extended stress holds at temperature can either retard or accelerate the crack growth rate. Therefore, to accurately predict the crack propagation life of an actual component, it is essential to approximate the true loading history. In military rotorcraft engine applications, the loading profile (stress amplitudes, temperature, and number of excursions) can vary significantly depending on the type of mission flown. To accurately assess the durability of a fleet of engines, the crack propagation life distribution of a specific component should account for the variability in the missions performed (proportion of missions flown and sequence). In this report, analytical and experimental studies are described that calibrate/validate the crack propagation prediction capability ]or a disk alloy under variable amplitude loading. A crack closure based model was adopted to analytically predict the load interaction effects. Furthermore, a methodology has been developed to realistically simulate the actual mission mix loading on a fleet of engines over their lifetime. A sequence of missions is randomly selected and the number of repeats of each mission in the sequence is determined assuming a Poisson distributed random variable with a given mean occurrence rate. Multiple realizations of random mission histories are generated in this manner and are used to produce stress, temperature, and time points for fracture mechanics calculations. The result is a cumulative distribution of crack propagation lives for a given, life limiting, component location. This information can be used to determine a safe retirement life or inspection interval for the given location.

Bonacuse, P. J.↗
NASA NTRS1999

Simulation of Crack Propagation in Engine Rotating Components Under Variable Amplitude Loading

The crack propagation life of tested specimens has been repeatedly shown to strongly depend on the loading history. Overloads and extended stress holds at temperature can either retard or accelerate the crack growth rate. Therefore, to accurately predict the crack propagation life of an actual component, it is essential to approximate the true loading history. In military rotorcraft engine applications, the loading profile (stress amplitudes, temperature, and number of excursions) can vary significantly depending on the type of mission flown. To accurately assess the durability of a fleet of engines, the crack propagation life distribution of a specific component should account for the variability in the missions performed (proportion of missions flown and sequence). In this report, analytical and experimental studies are described that calibrate/validate the crack propagation prediction capability for a disk alloy under variable amplitude loading. A crack closure based model was adopted to analytically predict the load interaction effects. Furthermore, a methodology has been developed to realistically simulate the actual mission mix loading on a fleet of engines over their lifetime. A sequence of missions is randomly selected and the number of repeats of each mission in the sequence is determined assuming a Poisson distributed random variable with a given mean occurrence rate. Multiple realizations of random mission histories are generated in this manner and are used to produce stress, temperature, and time points for fracture mechanics calculations. The result is a cumulative distribution of crack propagation lives for a given, life limiting, component location. This information can be used to determine a safe retirement life or inspection interval for the given location.

P J Bonacuse↗
DOE OSTI2026

Polymer Deconstruction and Redesign Strategies for Plastics Recycling

Advancing plastics recycling requires both the selective deconstruction of existing polymers and the design of new materials that enable efficient reuse without loss of performance. This perspective highlights an integrated approach that is rooted in polymer chemistry, catalysis, and process engineering which can enable a circular plastics economy. Here, we outline recent advances in catalytic, solvolytic, and enzymatic pathways for plastic deconstruction, and examine the molecular design principles driving next-generation recyclable-by-design and bio-based polymers. Despite these advances, major knowledge gaps remain in understanding the evolution of polymer morphology and catalyst structure during deconstruction, assessing deconstruction processes with realistic polymers, and offering redesigned polymers with competitive cost and environmental advantage over conventional plastics. United States Department of Energy (U.S. DOE) national laboratories offer unique capabilities to address these challenges through in situ and operando characterization, high-throughput experimentation, environmental studies, technoeconomic and life cycle assessment, scale-up support, and collaboration networks. Advances made in understanding plastic deconstruction mechanisms and structure-property correlations of redesigned polymers inform emerging research directions including autonomous experimentation, real-time feedback-enabled process optimization, and protein engineering for enzymatic depolymerization.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Undergraduate Women in STEM Internship Program

In collaboration with the Universities Research Association, Inc. (URA), establishment of the Undergraduate Women in STEM Internship pilot program assists Fermi Research Alliance, LLC (FRA) with honoring its commitment to increasing gender, racial and ethnic workforce diversity. This focused initiative is intended to invite, support and yield a qualified pipeline of alumnae underrepresented in FRA’s science and technology management and technical staff positions. Interns in this program spend 10-12 weeks at Fermilab working under the direct leadership, guidance and supervision of scientists, engineers, computing professionals, technicians and staff across all directorates performing hands-on research. In addition, the intern cohort meets with mentors and advisors to grow their professional networks, to take part in engaging and inclusive intellectual discussions, to directly benefit from workplace resources, and to participate in professional development and social engagement opportunities. The design of each research project and the supervision, mentorship and evaluation is conducted by a scientific, engineering, computing professional at Fermilab.

99 GENERAL AND MISCELLANEOUS↗
NASA NTRS2010

A Risk Assessment Architecture for Enhanced Engine Operation

On very rare occasions, in-flight emergencies have occurred that required the pilot to utilize the aircraft's capabilities to the fullest extent possible, sometimes using actuators in ways for which they were not intended. For instance, when flight control has been lost due to damage to the hydraulic systems, pilots have had to use engine thrust to maneuver the plane to the ground and in for a landing. To assist the pilot in these situations, research is being performed to enhance the engine operation by making it more responsive or able to generate more thrust. Enabled by modification of the propulsion control, enhanced engine operation can increase the probability of a safe landing during an inflight emergency. However, enhanced engine operation introduces risk as the nominal control limits, such as those on shaft speed, temperature, and acceleration, are exceeded. Therefore, an on-line tool for quantifying this risk must be developed to ensure that the use of an enhanced control mode does not actually increase the overall danger to the aircraft. This paper describes an architecture for the implementation of this tool. It describes the type of data and algorithms required and the information flow, and how the risk based on engine component lifing and operability for enhanced operation is determined.

Litt, Jonathan S.↗
DOE OSTI2021

Accelerated Creep Test Qualification of Creep-Resistance Using the Wilshire–Cano–Stewart Constitutive Model and Stepped Isostress Method

In this paper, a qualification of accelerated creep-resistance of Inconel 718 is assessed using the novel Wilshire–Cano–Stewart (WCS) model and the stepped isostress method (SSM) and predictions are made to conventional creep data. Conventional creep testing is a long-term continuous process; in fact, the ASME B&PV III requires that 10,000+ h of experiments must be conducted to each heat for materials employed in boilers and/or pressure vessel components. This process is costly and not feasible for rapid development of new materials. As an alternative, accelerated creep testing techniques have been developed to reduce the time needed to characterize the creep resistance of materials. Most techniques are based upon the time-temperature-stress superposition principle that predicts minimum-creep-strain-rate (MCSR) and stress-rupture behaviors but lack the ability to predict creep deformation and consider deformation mechanisms that occur for experiments of longer duration. The SSM has been developed, which enables the prediction of creep deformation response as well as reduce the time needed for qualification of materials. The SSM approach has been successful for polymer, polymeric composites, and recently has been introduced for metals. In this study, the WCS constitutive model, calibrated to SSM test data, qualifies the creep resistance of Inconel 718 at 750 °C and predictions are compared to conventional creep testing data. The WCS model has proven to make long-term predictions for stress-rupture, MCSR, creep deformation, and damage in metallic materials. The SSM varies stress levels after time interval adding damage to the material, which can be tracked by the WCS model. The SSM data is calibrated into the model and the WCS model generates realistic predictions of stress-rupture, MSCR, damage, and creep deformation. The calibrated material constants are used to generate predictions of stress-rupture and are postaudit validated using the National Institute of Material Science database. Similarly, the MCSR predictions are compared from previous studies. Finally, the creep deformation predictions are compared with real data and is determined that the results are well in between the expected boundaries. Material characterization and mechanical properties can be determined at a faster rate and with a more cost-effective method. This is beneficial for multiple applications such as in additive manufacturing, composites, spacecraft, and industrial gas turbines.

42 ENGINEERING↗
DOE OSTI2025

Through the lens of bioenergy crops: advances, bottlenecks, and promises of plant engineering

Advances in engineering of bioenergy crops were driven over the past years by adapting technological breakthroughs and accelerating conventional applications but also exposed intriguing challenges. New tools revealed rich interconnectivity in the exponentially growing and dynamic 'big' omics data' of metabolomes, transcriptomes, and genomes at previously inaccessible magnitude (global, cross-species, meta-) and resolution (single cell). Insights enabled fresh hypotheses and stimulated disciplines such as functional genomics with discovery of broad regulatory networks and their determinants, that is, DNA parts, including promoters, regulatory elements, and transcription factors. Their rational design, assembly into increasingly complex blueprints, and installation into diverse chassis is an existing frontier that may benefit from emerging technologies to address bottlenecks. Interweaving nature-inspired to fully synthetic parts has already allowed building of fine-tuned regulatory circuits, or new-to-nature metabolic routes insulated from the biological context of the chassis species. Similarly, developments and the evolving need for unifying principles in plant transformation and species-agnostic technologies highlight future opportunities for engineering the next generation of bioenergy plants.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2025

Influence of substitution pattern on the dynamics of internal conversion and intersystem crossing in thiopyridone isomers

We report a combined experimental and theoretical investigation of the ultrafast internal conversion (IC) and intersystem crossing (ISC) dynamics of two thiopyridone (TP) isomers in solution. Our study used ultrafast transient X-ray absorption spectroscopy (XAS) at the sulfur K-edge, in conjunction with electronic excited state surface hopping molecular dynamics and simulations of the excited state XAS, to investigate the impact of the functional group substitution pattern and solvent on the dynamics of IC and ISC. The combination of the localized X-ray probe and the simulation results enables, in part, the differentiation between ππ* and nπ* character excited states, as well as singlet and triplet states. Access to nπ* character excitations has particular value since they often prove challenging to assess with optical spectroscopy. For 2-TP, the photoexcited S 2 (ππ*) state rapidly undergoes IC to the S 1 (nπ*) state below the instrument response time, followed by ISC to the T 1 (ππ*) state on a timescale of 600 fs in acetonitrile. For 4-TP, the timescale of S 2 to S 1 IC increases to 330 fs and the timescale of ISC increases to more than 10 ps. The differences between isomers are rationalized by considering the key role of the, nπ* intermediates in mediating the intersystem crossing of these systems. Varying the substitution pattern of the molecule can stabilize or destabilize these intermediates leading to the increase in ISC rate in the ortho isomer as compared to the para isomer, while changing the solvent from acetonitrile to water had minimal effect on the electronic excited state relaxation mechanism.

Garratt, Douglas [SLAC National Accelerator Labora↗
DOE OSTI2025

Optical neural engine for solving scientific partial differential equations

Abstract Solving partial differential equations (PDEs) is the cornerstone of scientific research and development. Data-driven machine learning (ML) approaches are emerging to accelerate time-consuming and computation-intensive numerical simulations of PDEs. Although optical systems offer high-throughput and energy-efficient ML hardware, their demonstration for solving PDEs is limited. Here, we present an optical neural engine (ONE) architecture combining diffractive optical neural networks for Fourier space processing and optical crossbar structures for real space processing to solve time-dependent and time-independent PDEs in diverse disciplines, including Darcy flow equation, the magnetostatic Poisson’s equation in demagnetization, the Navier-Stokes equation in incompressible fluid, Maxwell’s equations in nanophotonic metasurfaces, and coupled PDEs in a multiphysics system. We numerically and experimentally demonstrate the capability of the ONE architecture, which not only leverages the advantages of high-performance dual-space processing for outperforming traditional PDE solvers and being comparable with state-of-the-art ML models but also can be implemented using optical computing hardware with unique features of low-energy and highly parallel constant-time processing irrespective of model scales and real-time reconfigurability for tackling multiple tasks with the same architecture. The demonstrated architecture offers a versatile and powerful platform for large-scale scientific and engineering computations.

Tang, Yingheng (ORCID:0009000153622546)↗
DOE OSTI2021

Towards standardized nuclear reactors: Seismic isolation and the cost impact of the earthquake load case

We report nuclear energy has a key role to play in global decarbonization. Impediments to the widespread deployment of reactors are their projected high capital cost and levelized cost of energy, and time required to analyze, design, license, construct, and commission them. The earthquake load case is a key cost driver for a new build nuclear plant, because near-surface soils and seismic hazard are different at each site, requiring site-specific analysis, design, engineering, qualification, licensing, and regulatory review, essentially making every design First-of-a-Kind (FoaK). To enable deployment at the scale needed for deep decarbonization, the cost and time impact of the seismic load case must be significantly mitigated, and plants must be standardized. Seismic base isolation has been proven to considerably reduce the earthquake response of structures and equipment but has yet to be applied to a nuclear power plant in the United States, in part because the financial impacts, positive or negative, are not known. Because there are no recent non-proprietary data to characterize the influence of the seismic load case on capital cost, it is difficult to confidently quantify the financial benefits of seismic isolation. Scheme-level designs of two fundamentally different advanced reactor buildings were developed to assemble cost data on the influence of the seismic load case. Both buildings were equipped with three bespoke pieces of safety-related equipment and analyzed for incremented levels of earthquake shaking to quantify the seismic penalty on equipment, in terms of vessel weights and horizontal accelerations. Using analysis results, a questionnaire was developed and transmitted to nuclear utilities, reactor developers, engineers, and equipment suppliers to collect cost data on engineering and fabrication costs for these unique pieces of safety-class equipment. Synthesis of the cost data showed that the seismic load case significantly affects the capital cost (sum of engineering and fabrication cost) of safety-class equipment, with engineering costs being comparable to fabrication costs. Standardization of safety-class equipment is made possible by seismic isolation, that is, equipment designed for minimal seismic robustness can resist earthquake shaking at a site of much higher seismic hazard. The average reduction in the capital cost of the safety-related equipment, enabled by seismic isolation, is a factor of two for FoaK equipment and a factor of five for standardized equipment.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1986

Orbit-on-demand vehicle propelled by air-turborocket/ramjet engines

A preliminary design study has been completed for a fully reusable, single-stage-to-orbit transatmospheric vehicle. The specified mission capability was to lift a 20,000 lb payload to low earth orbit. A ground accelerator-assisted horizontal take-off was chosen to increase operational flexibility. The multi-mode propulsion system included the use of air-turborocket, ramjet, scramjet and rocket engines. Weight and performance estimates were obtained for the vehicle. A computer package was developed to perform aerothermodynamic analyses of the propulsion modes throughout the flight environment from take-off to low earth orbit. Results are presented for a semi-optimized trajectory. The analysis indicates that a vehicle of this type has great potential for providing low cost, flexible access to space.

Hartung, L.↗
DOE OSTI2016

White paper on nuclear astrophysics and low energy nuclear physics Part 1: Nuclear astrophysics

This white paper informs the nuclear astrophysics community and funding agencies about the scientific directions and priorities of the field and provides input from this community for the 2015 Nuclear Science Long Range Plan. It also summarizes the outcome of the nuclear astrophysics town meeting that was held on August 21–23, 2014 in College Station at the campus of Texas A&M University in preparation of the NSAC Nuclear Science Long Range Plan. It also reflects the outcome of an earlier town meeting of the nuclear astrophysics community organized by the Joint Institute for Nuclear Astrophysics (JINA) on October 9–10, 2012 Detroit, Michigan, with the purpose of developing a vision for nuclear astrophysics in light of the recent NRC decadal surveys in nuclear physics (NP2010) and astronomy (ASTRO2010). Our white paper is informed informed by the town meeting of the Association of Research at University Nuclear Accelerators (ARUNA) that took place at the University of Notre Dame on June 12–13, 2014. In summary we find that nuclear astrophysics is a modern and vibrant field addressing fundamental science questions at the intersection of nuclear physics and astrophysics. These questions relate to the origin of the elements, the nuclear engines that drive life and death of stars, and the properties of dense matter. A broad range of nuclear accelerator facilities, astronomical observatories, theory efforts, and computational capabilities are needed. Answers to long standing key questions are well within reach in the coming decade because of the developments outlined in this white paper.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗