Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Defect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

Computational Investigation of Oxidative Etch Pitting in FiberForm and Its Impact on Material Properties

Oxidation-driven carbon erosion does not occur uniformly but rather through the development of localized etch pits at active surface sites. These active sites form due to atomic defects on the carbon surface, making them significantly more reactive than the surrounding, non-defective areas. As a result, these sites are the first to react during ablation, leading to their removal. This process creates new defects in neighboring atoms, increasing their reactivity and causing localized carbon removal around these active sites. In this way, the highly reactive defective areas serve as nucleation points for the formation and growth of etch pits, which can have adverse effects on structural integrity of FiberForm. To better understand how these etch pits impact the material properties of carbon fiber microstructures, we have developed a new capability within the direct simulation Monte Carlo (DSMC) framework to capture the etch pit formation process. This capability, integrated into the DSMC code SPARTA (Stochastic Parallel Rarefied-gas Time-accurate Analyzer), models material removal in the presence of active sites, leading to the formation of etch pits. The current work focuses on studying the effects of these etch pits on the material properties of FiberForm, a widely used base material in thermal protection systems (TPS). The microstructure of virgin FiberForm, obtained via X-ray microtomography, is imported into SPARTA to generate the ablated geometries with etch pits. These modified microstructures are then analyzed using the Porous Microstructure Analysis (PuMA) software to compute various material properties, including elasticity, thermal conductivity, and permeability. We investigate the variation of these properties due to the complex surface topology changes caused by etch pit formation. Additionally, we compare the effects of pitting with the conventional model of shrinking fibers, traditionally used to simulate the ablation of carbon structures. Significant differences emerge between the two approaches. Consequently, this physically realistic model of material removal through etch pit formation offers improved accuracy in predicting the degradation of carbon-based TPS during oxidation. It also provides insights into other mechanisms, such as spallation, where chunks of material are removed into the flow due to etch pit growth. Ultimately, this model enhances our understanding of failure modes in these materials during ablation.

PuMA↗

Ultrasonic scanning system for inspection of brazed tube joints

An ultrasonic scanning system used to inspect and evaluate in-place brazed tube joints is considered. The system was designed, developed, and built especially for nondestructive testing and was selected because of its known response to brazing defects not associated with material density changes. The scan system is capable of scanning brazed joints in union, tee, elbow and cross configuration of 3/16-inch through 5/8-inch diameters. It is capable of detecting brazed defects as small as 0.008 by 0.010-inch, which exceeds the 0.015-inch diameter defect resolution required by specification.

Haynes, J. L.↗

Rates and mechanisms of the atomic oxygen reaction with nickel at elevated temperatures

The oxidation of nickel by atomic oxygen at pressure from 1 to 45 N/sq m between 1050 and 1250 K was investigated. In these ranges, the oxidation was found to follow the parobolic rate law, viz., K sub p = 0.0000114 exp(-13410/T) g squared/cm4/sec for films of greater than 1 micron thickness and was pressure independent. The activation enthalpy for the oxidation reaction was 112 + or - 11 kj/mole (27 + or - 3 kcal/mole). Of a number of possible mechanisms and defect structures considered, it was shown that the most likely was a saturated surface defect model for atomic oxidation, based on reaction activation enthalpies, impurity effects, pressure independence, and magnitudes of rates. A model judged somewhat less likely was one having doubly ionized cationic defects rate controlling in both atomic and molecular oxygen. From comparisons of the appropriate processes, the following enthalpy values were derived: enthalpy of activation (Ni diffusion in Ni0) = 110 + or - 30 kj/mole and standard enthalpy change for reaction formation (doubly ionized cation vacancies in Ni0 from atomic oxygen)= -9 + or - 25 kj/mole.

Christian, J. D.↗

Cytogenic studies of blood (experiment M111)

The Skylab M111 experiment was a continuation of the preflight and postflight chromosomal analyses of the flight crews that have been performed since the Gemini 3 mission. The experiment was designed to determine whether some space flight parameter produces cytogenetic effects in human cells and to provide biological radiation dosimetric capability in the event of significant radiation exposure to a flight crew. On each of the Skylab flights, blood lymphocytes for analysis of chromosomes for structural defects were obtained from each of the prime crewmembers and from a ground-based control group before and after flight. Two types of defects were recorded. The minor defects included the following aberrations: chromatid fragments, chromosome fragments, and deletions. Structural rearrangements such as dicentrics, exchanges, ring chromosomes, and translocations were photographed, and the cells were karyotyped to delineate, when possible, the chromosome or chromosomes involved in the rearrangement. Result seems to indicate that the flight itself was not a major contributing factor.

Lockhart, L. H.↗

A review of the state-of-the-art of the non-destructive testing of flight pressure vessels

The design of flight vessels is based on a nominal stress requirement and a fracture mechanics approach, and optimization of the weight of the vessel is based on the smallest size defect that can be detected with a high degree of confidence. The wide variety of metals used for fabrication, and the different defects that may be present in them at every stage, up to completion of the vessel, is described. Techniques currently being used for NDT are described along with their advantages, limitations and limits of detectability at high levels of confidence. Techniques considered for use in the future to improve the limits of the minimum flaw size that can currently be detected include the Delta Scan and Acoustic Emission techniques. The construction of space vessels for use in the future has been modified to reduce the presence of critical defects and so to improve the cost effectiveness of projected NDT requirements.

Noronha, P. J.↗

Studies of silicon PN junction solar cells

Silicon pn junction solar cells made with low-resistivity substrates show poorer performance than traditional theory predicts. The purpose of this research was to identify and characterize the physical mechanisms responsible for the discrepancy. Attention was concentrated on the open circuit voltage in shallow junction cells of 0.1 ohm-cm substrate resistivity. A number of possible mechanisms that can occur in silicon devices were considered. Two mechanisms which are likely to be of main importance in explaining the observed low values of open-circuit voltage were found: (1) recombination losses associated with defects introduced during junction formation, and (2) inhomogeneity of defects and impurities across the area of the cell. To explore these theoretical anticipations, various diode test structures were designed and fabricated and measurement configurations for characterizing the defect properties and the areal inhomogeneity were constructed.

Lindholm, F. A.↗

Investigation of crystal growth from solutions

Growth of organic compounds from solution, in particular Rochelle salt and triglycine sulphate, was investigated. Ground-based experiments showed that gravity-driven convection currents in the growth solution influenced defect production in crystals, degraded ferroelectric quality, and indicated that an experiment done in a zero-gravity environment would be beneficial. A crystal of Rochelle salt was grown on board Skylab-4. The quality of this crystal was compared to earth-grown crystals and its unusual features were studied. A typical defect produced in this convection-free environment was a long straight tube extending in the direction of the c crystal axis. These tubes were much longer and more regularly arranged than in similar earth-grown crystals. The crystal was actually several crystals with corresponding axes parallel to each other. Ferroelectric hysteresis experiments showed that some parts of the crystal had many defects, while other parts were of extremely good quality.

Miyagawa, I.↗

Cameras for semiconductor process control

The application of X-ray topography to semiconductor process control is described, considering the novel features of the high speed camera and the difficulties associated with this technique. The most significant results on the effects of material defects on device performance are presented, including results obtained using wafers processed entirely within this institute. Defects were identified using the X-ray camera and correlations made with probe data. Also included are temperature dependent effects of material defects. Recent applications and improvements of X-ray topographs of silicon-on-sapphire and gallium arsenide are presented with a description of a real time TV system prototype and of the most recent vacuum chuck design. Discussion is included of our promotion of the use of the camera by various semiconductor manufacturers.

Porter, W. A.↗

Evaluation of flawed composite structure under static and cyclic loading

This paper presents the results of a program investigating the effects of initial defects on the fatigue and fracture response of composite laminates. The structural laminates investigated were a typical angle-ply laminate, a polar/hoop-wound pressure vessel laminate, and a typical engine fan blade laminate. Defects investigated were full- and half-penetration circular holes, full- and half-penetration slits, and countersink holes. Results are presented showing the effects of the defect size and type on the static fracture strength, fatigue performance, and residual static strength. The results of inspection procedures are shown, describing the effect of cyclic and static loadings on damage propagation in composite laminates. The data in this study were used to define proof test levels as a qualification procedure in composite structure subjected to cyclic loading.

Porter, T. R.↗

Definition of mutually optimum NDI and proof test criteria for 2219 aluminum pressure vessels. Volume 1: Methods

The requirements for proof testing and nondestructive inspection of aluminum pressure vessels were discussed. The following conclusions are (1) lack-of-fusion weld defects are sufficiently tight in the as-welded condition to be considered undetectable; (2) proof-level loads are required to fully open lack-of-fusion weld defects; (3) significant crack opening occurs at subproof levels so that an inspection enhancement loading treatment designed to avoid catastrophic failure is feasible; (4) currently used proof levels for 2219 pressure vessels are adequate for postproof inspection; (5) quantification of defect size and location using collimated ultrasonic pitch-catch techniques appears sufficiently feasible for tankage to warrant developmental work; (6) for short-time single-cycle pressure-vessel applications, postproof inspection is desirable; and (7) for long-term multiple-cycle pressure-vessel applications, postproof inspection is essential for life assurance.

Schwartzberg, F. R.↗

Evaluation of flawed composite structural components under static and cyclic loading

The effects of initial defects on the fatigue and fracture response of graphite-epoxy composite laminates are presented. The structural laminates investigated were a typical angle ply laminate, a polar/hoop wound pressure vessel laminate, and a typical engine fan blade laminate. Defects investigated were full and half penetration circular holes, full and half penetration slits, and countersink holes. The effects of the defect size and type on the static fracture strength, fatigue performance, and residual static strength are shown as well as the results of loadings on damage propagation in composite laminates. The data obtained were used to define proof test levels as a qualification procedure in composite structure subjected to cyclic loading.

Porter, T. R.↗

AXAF optical technology analysis

A grazing incidence telescope with six nested subsystems is investigated through the effects of misalignment and surface deformations on it's image quality. The axial rms-spot size serves as measure for the image quality. The surface deformations are simulated by ellipsoidal and sinusoidal deviation elements. Each type of defect is analyzed in the single two-element system. The full nested system is then analyzed in the presence of all possible defects on all twelve elements, whereby the magnitude of the defects is randomized within a given upper limit.

Korsch, D.↗

Calculations and measurements in support of the triglycine sulfate zero gravity growth experiment

Two areas of investigation which are required for maximum utilization of the flight experiment results from the solution growth of crystals of triglycine sulfate (TGS) are addressed. The use of an ultramicroscope to characterize structural defects in the grown TGS crystals is discussed. Mie theory is applied to the light scattering expected from idealized crystal defects in order to predict the sensitivity of ultramicroscopy in the detection of small defects. Secondly, the measurement of optical properties of TGS solutions in water is discussed. This data is needed in order to interpret interferometric studies of mass transport through the TGS solution during the growth phase of the flight experiment. In particular, refractive index data is obtained for a wide range of temperatures and concentrations of TGS solutions. Absorbance measurements in the ultraviolet have also been made for the same samples.

Springer, J. M.↗

Radiation damage annealing mechanisms and possible low temperature annealing in silicon solar cells

Deep level transient spectroscopy and the Shockley-Read-Hall recombination theory are used to identify the defect responsible for reverse annealing in 2 ohm-cm n+/p silicon solar cells. This defect, with energy level at Ev + 0.30 eV, has been tentatively identified as a boron-oxygen-vacancy complex. It has been also determined by calculation that the removal of this defect could result in significant annealing at temperatures as low as 200 C for 2 ohm-cm and lower resistivity cells.

Weinberg, I.↗

Attenuation of ultrasonic interface waves on metal-polymer-metal boundaries

The measured sensitivity of interface wave attenuation to defects near the bondline and to variations in the viscosity of the adhesive layer was compared with theoretical changes predicted by the Rokhin model. Differential interferometric optical measurements of interface wave attenuation due to defects near glass polymer metal boundaries are discussed. Pitch catch and pulse echo methods which use variable angle wedge transducers to generate and receive modified interface waves and to measure large bondline defects and adhesive viscosity are described.

Claus, R. O.↗

Study of the effects of impurities on the properties of silicon solar cell

The effect of defects across the back-surface-field junction on the performance of high efficiency and thin solar cells, using a developed-perimeter device model for the three-dimensional defects is investigated. Significant degradation of open-circuit voltage can occur even if there are only a few defects distributed in the bulk of the solar cell. Two features in the thickness dependences of the fill factor and efficiency in impurity-doped back-surface-field solar cells are discovered in the exact numerical solution which are associated with the high injection level effect in the base and not predicted by the low-level analytical theory. What are believed to be the most accurate recombination parameters at the Ti center to date are also given and a theory is developed which is capable of distinguishing an acceptor-like deep level from a donor-like deep level using the measured values of the thermal emission and capture cross sections.

Sah, C. T.↗

An EBIC study of HEM polycrystalline silicon

Low-cost silicon for solar cells grown by the heat exchanger method (HEM) was studied in the electron beam induced current (EBIC) mode of a scanning electron microscope (SEM). Comparisons were made between the defects observed optically and the recombination centers visible in EBIC. Much of the HEM material was single crystalline, but structural defects were found from areas near the corners of the grown material. Most of these defects consisted of linear twin boundaries and grain boundaries. The electrical activity of these boundaries was dependent on symmetry of the boundaries. Symmetric twin boundaries did not exhibit recombination activity while unsymmetric twin boundaries were electrically active.

Koch, T.↗