SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Crop area and yield for winter wheat is found by analysis of LANDSAT pictures. Correlation between measure and yield is established from measurements on known wheatfields with known yields.
A bench scale fluidized bed combustor was constructed with a conical shape so that the enlarged upper part of the combustor would also serve as a granular bed filter. The combustor was fed coal and limestone. Ninety-nine tests of about four hours each were conducted over a range of conditions. Coal-to-air ratio varied from 0.033 to 0.098 (all lean). Limestone-to-coal ratio varied from 0.06 to 0.36. Bed depth varied from 3.66 to 8.07 feet. Temperature varied from 1447 to 1905 F. Pressure varied from 40 to 82 psia. Heat transfer area had the range zero to 2.72 ft squared. Two cone angles were used. The average particulate carry over of 2.5 grains/SCF was appreciably less than cylindrical fluidized bed combustors. The carry over was correlated by multiple regression analysis to yield the dependence on bed depth and hence the collection efficiency, which was 20%. A comparison with a model indicated that the exhaust port may be below the transport disengaging height for most of the tests, indicating that further reduction in carry over and increase in collection efficiency could be affected by increasing the freeboard and height of the exhaust port above the bed.
Development of the plasma sprayed graded, layered ZrO2/CoCrAlY seal system for gas turbine engine blade tip seal application up to 1589 K (2400 F) surface temperature was continued. Methods of improvement of the cyclic thermal shock resistance of the sprayed zirconia seal system were investigated. The most promising method, reduction of the ceramic thickness and metallic substrate stiffness were selected based upon potential and feasibility. Specimens were fabricated and experimentally evaluated to: (1) substantiate the capacity of the geometry changes to reduce operating stresses in the sprayed structure; and (2) define the abradability, erosion, thermal shock and physical property characteristic for the sprayed ceramic seal system. Thermal stress analysis was performed and correlated with thermal shock test results.
A bench-scale pressurized fluidized bed combustor (PFBC) constructed with a conical shape to reduce the particulate carryover is examined. The combustor was fed coal and limestone with the coal to air ratio varying from 0.033 to 0.098 (all lean) and the coal to limestone ratio varying from 0.06 to 0.36. Two cone angles were used and it is shown that the average particulate carryover of 2.5 grains/SCF is appreciably less than cylindrical fluidized bed combustors. In addition the carryover was correlated by multiple regression analysis to yield the dependence on bed depth and hence the collection efficiency, which was 20%. Finally, a comparison with a model indicated that the exhaust port may be below the transport disengaging height for most of the tests showing that further improvements could be achieved by increasing the freeboard height of the exhaust port above the bed.
The NASA Langley Research Center has the responsibility to advance the state-of-the-art in the area of stall/spin technology. This includes the development and validation of experimental and analytical techniques for the prediction of stall/spin characteristics. As a part of this effort, a rotary balance facility located in the Langley spin tunnel was developed two and a half years ago to rapidly identify an airplane's aerodynamic characteristics in a rotational flow environment. On-line rotary balance data plots and on-line predicted steady spin modes permit the designer to develop, on site, a configuration highly resistant to spins, or one which has good spin characteristics, i.e., no spin equilibrium conditions possible with lateral-directional controls neutral, if the airplane is to be used for acrobatic maneuvers or training. The rotary balance data are also used to compute time histories of a spin's incipient, developed, and recovery phases. These spin analysis techniques and their correlation with spin tunnel model and full-scale flight results are discussed herein.
The three basic methods of weight prediction (fixed-fraction, statistical correlation, and point stress analysis) and some of the computer programs that have been developed to implement them are discussed. A modified version of the WAATS (Weights Analysis of Advanced Transportation Systems) program is presented, along with input data forms and an example problem.
The problem of stress wave generation in a linear thermoelastic solid by a pulsed magnetic field is investigated both analytically and experimentally for a cylindrically symmetric conducting solid. A dynamic response analysis is developed to correlate magnetic, thermal, and stress fields in the solid with the time history of the electric current. In the experiment, a transient magnetic field was applied normal to a large conducting plate with a circular hole. Initially the field was confined to the interior of the circular hole. The field was generated by discharging a large capacitor bank through a solenoidal coil. The plane-stress cylindrical stress waves are 1-D in nature. The relative effects of the magnetic body force and thermoelastic stresses, both generated by the electromagnetic field, are assessed.
Progress in processing and analysis of Investigator B MAGSAT data is reported. Data processing tasks required prior to data analysis, including translation and reformatting of tapes and development of computer routines, were performed. A scalar anomaly map of Antarctica is near completion. Data analysis included a qualitative correlation of NASA's 4/81 scalar map of Antarctica with other geopotential data and correlation of POGO and continental scale gravity data with MAGSAT data. A magnetic high was found to exist over the Ross Embayment.
Two remote receiving sites have been set up at a distance of approx 40 km from the main MF radar system. This allows measurement of upper atmosphere winds from 60-120 km (3 km resolution) at the corners of an approximately equilateral triangle of side approx 20 km. Some preliminary data are compared through cross correlation and cross spectral analysis in an attempt to determine the horizontal velocity of wind perturbations and/or the horizontal wavelength and phase velocity of gravity waves.
Work is in progress to estimate leaf area index (LAI) of temperate closed canopy coniferous forests using transects in Oregon and California. This variable will be measured using remote sensing techniques including correlations of ground dimensional analysis with linear waveband combinations. LAI will be related to important biological variables such as net primary productivity, biomass, and biogenic gas emission fluxes. The spatial variation in LAI, when coupled with species composition, will be used in part to describe the spatial variation and temporal dynamics of biogeochemical cycling.
The relation between rotational modulation of the ultraviolet solar irradiance and variations in atmospheric ozone has been investigated using Fourier transform harmonic analysis and cross-correlations. Ozone variations with the same period and phase as 13.5 day or 27-day solar flux variations occur at tropical and subtropical latitudes over a range of pressure levels centered about 3 mbar. The solar-forced oscillation is stronger in the summer hemisphere; as temperature-related variations would be stronger in winter. Changes in solar irradiance over the 11-year cycle can be estimated by scaling rotational modulation. Using this estimate and the ozone-sun relation obtained for rotational modulation yields solar cycle changes of 3.5 percent in 3 percent mixing ratio comparable to that predicted from halocarbons and 0.7 mbar in total ozone.
Pulsed laser sheet velocimetry yields nonintrusive measurements of velocity vectors across an extended 2-dimensional region of the flow field. The application of optical correlation techniques to the analysis of multiple exposure laser light sheet photographs can reduce and/or simplify the data reduction time and hardware. Here, Matched Spatial Filters (MSF) are used in a pattern recognition system. Usually MSFs are used to identify the assembly line parts. In this application, the MSFs are used to identify the iso-velocity vector contours in the flow. The patterns to be recognized are the recorded particle images in a pulsed laser light sheet photograph. Measurement of the direction of the partical image displacements between exposures yields the velocity vector. The particle image exposure sequence is designed such that the velocity vector direction is determined unambiguously. A global analysis technique is used in comparison to the more common particle tracking algorithms and Young's fringe analysis technique.
The paper describes a turbofan-engine measurement program utilizing a variety of diagnostic techniques to identify a source of core-generated noise which contributes to the overall external engine noise characteristics. Included in the turbofan engine diagnostics are data examination, time domain correlation, and frequency domain analysis. It is found that the turbulent pressure fluctuations within the combustor are a source for core noise which propagates through the nozzle and radiates to the far-field.
Ten thin plastic materials (Velostat, RCAS 1200, Llumalloy, Herculite 80, RCAS 2400, Wrightlon 7000, PVC, Aclar 22A, Mylar, and Polyethylene) were tested for electrostatic properties by four different devices: (1) The static decay meter, (2) the manual triboelectric testing device, (3) the robotic triboelectric testing device, and (4) the resistivity measurement adapter device. The static decay meter measured the electrostatic decay rates in accordance with the Federal Test Method Standard 101B, Method 4046. The manual and the robotic triboelectric devices measured the triboelectric generated peak voltages and the five-second decay voltages in accordance with the criteria for acceptance standards at Kennedy Space Center. The resistivity measurement adapter measured the surface resistivity of each material. An analysis was made to correlate the data among the four testing devices. For the material tested the pass/fail results were compared for the 4046 method and the triboelectric testing devices. For the limited number of materials tested, the relationship between decay rate and surface resistivity was investigated as well as the relationship between triboelectric peak voltage and surface resistivity.
The technology base required to fabricate silicon nitride components with the strength, reliability, and reproducibility necessary for actual heat engine applications is presented. Task 2 was set up to develop test bars with high Weibull slope and greater high temperature strength, and to conduct an initial net shape component fabrication evaluation. Screening experiments were performed in Task 7 on advanced materials and processing for input to Task 2. The technical efforts performed in the second year of a 5-yr program are covered. The first iteration of Task 2 was completed as planned. Two half-replicated, fractional factorial (2 sup 5), statistically designed matrix experiments were conducted. These experiments have identified Denka 9FW Si3N4 as an alternate raw material to GTE SN502 Si3N4 for subsequent process evaluation. A detailed statistical analysis was conducted to correlate processing conditions with as-processed test bar properties. One processing condition produced a material with a 97 ksi average room temperature MOR (100 percent of goal) with 13.2 Weibull slope (83 percent of goal); another condition produced 86 ksi (6 percent over baseline) room temperature strength with a Weibull slope of 20 (125 percent of goal).
Pulsed laser sheet velocimetry yields noninstrusive measurements of velocity vectors across an extended 2-dimensional region of the flow field. The application of optical correlation techniques to the analysis of multiple exposure laser light sheet photographs can reduce and/or simplify the data reduction time and hardware. Here, Matched Spatial Filters (MSF) are used in a pattern recognition system. Usuallay MSFs are used to identify the assembly line parts. In this application, the MSFs are used to identify the iso-velocity vector contours in the flow. The patterns to be recognized are the recorded particle images in a pulsed laser light sheet photograph. Measurement of the direction of the particle image displacements between exposures yields the velocity vector. The particle image exposure sequence is designed such that the velocity vector direction is determined unambiguously. A global analysis technique is used in comparison to the more common particle tracking algorithms and Young's fringe analysis technique.
The influence of shear flexibility on overall postbuckling response was assessed, and transverse shear stress distributions in relation to panel failure were examined. Nonlinear postbuckling results are obtained for finite element models based on classical laminated plate theory and first-order shear deformation theory. Good correlation between test and analysis is obtained. The results presented analytically substantiate the experimentally observed failure mode.
Flight tests were conducted at three different altitudes to detect transition on a smoothed test region of a swept-wing business jet wing using surface hot-film sensors and sublimating chemicals. Strong influence of sweep angle on transition location was observed when the aircraft was flown at some sideslip conditions to simulate changes in effective wing sweep angle. No effects of engine noise on transition were measured when different engine power settings were used. Flight instrumentation and ground data analysis techniques are described. Correlation was obtained between the hot-film sensor signals and sublimating chemicals for transition detection. Crossflow vortices were observed for one flight condition. Results of analyzed data for various flight-test conditions are presented.