Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CELLULOSE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Land-use change and greenhouse gas emissions from corn and cellulosic ethanol

Background: The greenhouse gas (GHG) emissions that may accompany land-use change (LUC) from increased biofuel feedstock production are a source of debate in the discussion of drawbacks and advantages of biofuels. Estimates of LUC GHG emissions focus mainly on corn ethanol and vary widely. Increasing the understanding of LUC GHG impacts associated with both corn and cellulosic ethanol will inform the on-going debate concerning their magnitudes and sources of variability. Results: In our study, we estimate LUC GHG emissions for ethanol from four feedstocks: corn, corn stover, switchgrass, and miscanthus. We use new computable general equilibrium (CGE) results for worldwide LUC. U.S. domestic carbon emission factors are from state-level modelling with a surrogate CENTURY model and U.S. Forest Service data. This paper investigates the effect of several key domestic lands carbon content modelling parameters on LUC GHG emissions. International carbon emission factors are from the Woods Hole Research Center. LUC GHG emissions are calculated from these LUCs and carbon content data with Argonne National Laboratory’s Carbon Calculator for Land Use Change from Biofuels Production (CCLUB) model. Our results indicate that miscanthus and corn ethanol have the lowest (-10 g CO2e/MJ) and highest (7.6 g CO2e/MJ) LUC GHG emissions under base case modelling assumptions. The results for corn ethanol are lower than corresponding results from previous studies. Switchgrass ethanol base case results (2.8 g CO2e/MJ) were the most influenced by assumptions regarding converted forestlands and the fate of carbon in harvested wood products. They are greater than miscanthus LUC GHG emissions because switchgrass is a lower-yielding crop. Finally, LUC GHG emissions for corn stover are essentially negligible and insensitive to changes in model assumptions. Conclusions: This research provides new insight into the influence of key carbon content modelling variables on LUC GHG emissions associated with the four bioethanol pathways we examined. Our results indicate that LUC GHG emissions may have a smaller contribution to the overall biofuel life cycle than previously thought. Additionally, they highlight the need for future advances in LUC GHG emissions estimation including improvements to CGE models and aboveground and belowground carbon content data.

09 BIOMASS FUELS↗

Comprehensive characterization of non-cellulosic recalcitrant cell wall carbohydrates in unhydrolyzed solids from AFEX-pretreated corn stover

Inefficient carbohydrate conversion has been an unsolved problem for various lignocellulosic biomass pretreatment technologies, including AFEX, dilute acid, and ionic liquid pretreatments. Previous work has shown 22% of total carbohydrates are typically unconverted, remaining as soluble or insoluble oligomers after hydrolysis (72 h) with excess commercial enzyme loading (20 mg enzymes/g biomass). Nearly one third (7 out of 22%) of these total unconverted carbohydrates are present in unhydrolyzed solid (UHS) residues. The presence of these unconverted carbohydrates leads to a considerable sugar yield loss, which negatively impacts the overall economics of the biorefinery. Current commercial enzyme cocktails are not effective to digest specific cross-linkages in plant cell wall glycans, especially some of those present in hemicelluloses and pectins. Thus, obtaining information about the most recalcitrant non-cellulosic glycan cross-linkages becomes a key study to rationally improve commercial enzyme cocktails, by supplementing the required enzyme activities for hydrolyzing those unconverted glycans.

Biotechnology & Applied Microbiology↗

Single mutation at a highly conserved region of chloramphenicol acetyltransferase enables isobutyl acetate production directly from cellulose by Clostridium thermocellum at elevated temperatures

Abstract Background Esters are versatile chemicals and potential drop-in biofuels. To develop a sustainable production platform, microbial ester biosynthesis using alcohol acetyltransferases (AATs) has been studied for decades. Volatility of esters endows high-temperature fermentation with advantageous downstream product separation. However, due to the limited thermostability of AATs known, the ester biosynthesis has largely relied on use of mesophilic microbes. Therefore, developing thermostable AATs is important for ester production directly from lignocellulosic biomass by the thermophilic consolidated bioprocessing (CBP) microbes, e.g., Clostridium thermocellum . Results In this study, we engineered a thermostable chloramphenicol acetyltransferase from Staphylococcus aureus (CAT Sa ) for enhanced isobutyl acetate production at elevated temperatures. We first analyzed the broad alcohol substrate range of CAT Sa . Then, we targeted a highly conserved region in the binding pocket of CAT Sa for mutagenesis. The mutagenesis revealed that F97W significantly increased conversion of isobutanol to isobutyl acetate. Using CAT Sa F97W, we demonstrated direct conversion of cellulose into isobutyl acetate by an engineered C. thermocellum at elevated temperatures. Conclusions This study highlights that CAT is a potential thermostable AAT that can be harnessed to develop the thermophilic CBP microbial platform for biosynthesis of designer bioesters directly from lignocellulosic biomass.

Biotechnology & Applied Microbiology↗

Data for Hydrothermal Pretreatment for Valorization of Genetically Engineered Bioenergy Crop for Lipid and Cellulosic Sugar Recovery

Lipids accumulated in the vegetative tissues of cellulosic feedstocks can be a potential raw material for biodiesel and bioethanol production. In this work, bagasse of genetically engineered sorghum was subjected to liquid hot-water pretreatment at 170, 180, and 190 °C for different reaction time. Under the optimal pretreatment condition (170 °C, 20 min), the residue was enriched in glucan (57.39 ± 2.63 % w/w) and xylan (13.38 ± 0.49 % w/w). The total lipid content of the pretreated residue was 6.81% w/w, similar to that observed in untreated bagasse (6.30% w/w). Pretreatment improved the enzymatic digestibility of bagasse, allowing a recovery of 79% w/w and 86% w/w of glucose and xylose, respectively. The pretreatment and enzymatic saccharification resulted in a 2-fold increase in total lipid in enzymatic residue compared to the original bagasse. Thus, pretreatment and enzymatic hydrolysis enabled high sugar recovery while concentrating triglycerides and free fatty acids in the residue.

Conversion↗

Data for Spatially Varying Costs of GHG Abatement with Alternative Cellulosic Feedstocks for Sustainable Aviation Fuels

Cellulosic biomass-based sustainable aviation fuels (SAFs) can be produced from various feedstocks. The breakeven price and carbon intensity of these feedstock-to-SAF pathways are likely to differ across feedstocks and across spatial locations due to differences in feedstock attributes, productivity, opportunity costs of land for feedstock production, soil carbon effects, and feedstock composition. We integrate feedstock to fuel supply chain economics and life-cycle carbon accounting using the same system boundary to quantify and compare the spatially varying greenhouse gas (GHG) intensities and costs of GHG abatement with SAFs derived from four feedstocks (switchgrass, miscanthus, energy sorghum, and corn stover) at 4 km resolution across the U.S. rainfed region. We show that the optimal feedstock for each location differs depending on whether the incentive is to lower breakeven price, carbon intensity, or cost of carbon abatement with biomass or to have high biomass production per unit land. The cost of abating GHG emissions with SAF ranges from $181 Mg−1 CO2e to more than $444 Mg−1 CO2e and is lowest with miscanthus in the Midwest, switchgrass in the south, and energy sorghum in a relatively small region in the Great Plains. While corn stover-based SAF has the lowest breakeven price per gallon, it has the highest cost of abatement due to its relatively high GHG intensity. Our findings imply that different types of policies, such as volumetric targets, tax credits, and low carbon fuel standards, will differ in the mix of feedstocks they incentivize and locations where they are produced in the U.S. rainfed region. Note: Column V in TableS7_DayCentSimulatedYield.csv should be labelled Corn Stover CoSo-NT-50% Max.

Geospatial↗

Cellulosic Ethanol Potential of Feedstocks Grown on Marginal Lands

To examine the chemical composition and ethanol production of feedstocks grown on marginal lands, prairie cordgrass and switchgrass from waterlogged land, saline land, and saline water irrigated land were evaluated. Samples were pretreated using 1% w w -1 dilute acid at 160°C for 10 min, and simultaneous saccharification and cofermentation was conducted using industrial engineered . Samples grown on land irrigated with saline water had 2.8-fold higher total ash content compared to the other types of land, resulting in lower carbohydrate concentrations. Yeast fermented glucose and xylose simultaneously; almost all of the sugars were consumed, indicating that salts present in biomass ash did not inhibit yeast performance. Ethanol production from the waterlogged and saline lands was 2,500 to 4,700 L ha -1 , which is comparable to that of samples grown on other agricultural lands. Finally, prairie cordgrass and switchgrass grown on marginal lands could be potential feedstocks for cellulosic biofuel. Keywords: Irrigation, Marginal land, Prairie cordgrass, Saline, Simultaneous saccharification and cofermentation, Switchgrass, Waterlogging.

54 ENVIRONMENTAL SCIENCES↗

Accurately estimating and minimizing costs for the cellulosic biomass supply chain with statistical process control and the Taguchi Loss Function

This research focuses on the statistical evaluation of the feedstock attributes of the biomass supply chain and the estimation of attribute costs as a function of the feedstock variability. Challenges of using cellulosic feedstocks include the variability of feedstock quality (e.g., ash content and moisture content), which impacts the final cost of the manufactured product. Statistical Process Control (SPC), Taguchi Loss Function, and components of variance techniques were illustrated for quantifying cumulative variance in the biomass supply chain. Costs in the presence of cumulative variance were estimated for switchgrass (Panicum virgatum L.) and loblolly pine residues (Pinus taeda L.). Findings of the study indicated that additional costs from ash content variability in switchgrass increased the net cost by $\$19.15$ per dry tonne. Additional costs from densification due to particle size variation increased net cost by $\$11.59$ per dry tonne. Moisture content variation increased costs by $\$14.86$ per dry tonne. This would represent a 50 to 100% increase in costs due to variation based on a $\$60$ to $\$70$ per dry tonne manufactured product cost. This study illustrates that total costs may be considerably underestimated if the influence of variance for key factors in the supply chain and associated costs are not estimated.

59 BASIC BIOLOGICAL SCIENCES↗

Biomass Production a Stronger Driver of Cellulosic Ethanol Yield than Biomass Quality

Core Ideas Fermentable sugars were greatest in corn stover > perennial grasses > polycultures. Corn stover had the highest ethanol content. Miscanthus had the highest ethanol yield potential on a per hectare basis. Ethanol yield potential per hectare of switchgrass ≥ corn stover. Biomass yield was the strongest driver of per hectare ethanol yield. Many crops have been proposed as feedstocks for the emerging cellulosic ethanol industry, but information is lacking about the relative importance of feedstock production and quality. We compared yield and sugar content for seven bioenergy cropping systems in south‐central Wisconsin (ARL) and southwestern Michigan (KBS) during three growing seasons (2012 through 2014). The cropping systems were (i) continuous corn stover ( Zea mays L.), (ii) switchgrass ( Panicum virgatum L.), (iii) giant miscanthus ( Miscanthus × giganteus Greef & Deuter ex Hodkinson & Renvoize), (iv) hybrid poplar ( Populus nigra × P. maximowiczii A. Henry ‘NM6’), (v) native grass mix, (vi) early successional community, and (vii) restored prairie. A high‐throughput pretreatment and fermentation assay showed corn stover with the highest sugar content (213 g glucose kg −1 [Glc] and 115 g xylose kg −1 [Xyl]) followed by the two monoculture perennial grass treatments (154 [Glc] and 88 [Xyl]) and then the herbaceous polycultures (135 [Glc] and 77 [Xyl]). Biomass production and sugar content were combined to calculate ethanol yields. Miscanthus had the highest per hectare ethanol yields (1957 l ha −1 yr −1 ARL, 2485 l ha −1 yr −1 KBS) followed by switchgrass (1091 l ha −1 yr −1 ARL, 1017 l ha −1 yr −1 KBS) and corn stover (1121 l ha −1 yr −1 ARL, 878 l ha −1 yr −1 KBS). Perennial grass cropping systems (i.e., switchgrass and miscanthus) had higher per hectare ethanol yields at both sites relative to diverse systems that included dicots. Despite feedstock differences in fermentable sugars, biomass production was the strongest driver of per hectare ethanol yield.

09 BIOMASS FUELS↗

Effect of Sodium Carboxymethyl Celluloses on Water-catalyzed Self-degradation of 200°C-heated Alkali-Activated Cement

We investigated the usefulness of sodium carboxymethyl celluloses (CMC) in promoting self-degradation of 200°C-heated sodium silicate-activated slag/Class C fly ash cementitious material after contact with water. CMC emitted two major volatile compounds, CO 2 and acetic acid, creating a porous structure in cement. CMC also reacted with NaOH from sodium silicate to form three water-insensitive solid reaction products, disodium glycolate salt, sodium glucosidic salt, and sodium bicarbonate. Other water-sensitive solid reaction products, such as sodium polysilicate and sodium carbonate, were derived from hydrolysates of sodium silicate. Dissolution of these products upon contact with water generated heat that promoted cement’s self-degradation. Thus, CMC of high molecular weight rendered two important features to the water-catalyzed self-degradation of heated cement: One was the high heat energy generated in exothermic reactions in cement; the other was the introduction of extensive porosity into cement.

15 GEOTHERMAL ENERGY↗

Fulton Cellulosic Ethanol Biorefinery

Final report on work performed by BlueFire on the deployment of acid hydrolysis technology to convert cellulosic waste materials into renewable fuels, power and chemicals in a production facility to be located in Fulton, Mississippi.

09 BIOMASS FUELS↗

An integrated process for butanol production from cellulosic biomass and CO 2 using engineered clostridia in a linear immobilized bioreactor

Engineered platforms using mixed microbial consortia to consolidate multiple reaction steps and perform disparate conversions simultaneously can substantially enhance the carbon efficiency of biomass conversion processes and lower the biofuel cost to an economically competitive level. In this project, an integrated process will be developed to produce n-butanol from cellulosic biomass and waste gas streams using two engineered clostridial strains, one butanol-tolerant solventogenic strain and one carboxydotrophic acetogen, co-immobilized in a “Linear Immobilized Bioreactor” (LIBR). The CO 2 and H 2 produced by the solventogenic strain will be used by the carboxydotrophic strain to produce acetate (and butyrate) that in turns can be used by the solventogenic strain to produce more butanol. Such a co-cultured fermentation has the potential to increase butanol production from biomass hydrolysate sugars by up to 50% with 100% reduction in CO 2 emission. Butanol produced in the fermentation will be stripped by the rising bubbles of fermentation produced gases (CO 2 and H 2 ) in the LIBR and separated via a condenser, alleviating butanol inhibition while achieving continuous butanol production at a high productivity and product titer, which can reduce both water and energy consumptions by over 50% compared to conventional ethanol and ABE fermentation processes. Phase I study proved the new bioprocess concept and verified our hypothesis that the proposed LIBR and co-cultured fermentation can enhance the conversion of lignocellulosic sugars to butanol with higher butanol yield, productivity and titer, leading to reduced biobutanol cost to compete more favorably with bioethanol and fossil fuels. A prototype lab-scale LIBR for multiphase fermentation was constructed to investigate and demonstrate the technical feasibility and advantages of the LIBR for multiphase fermentation involving sugars and gaseous substrates. The LIBR will be optimized and evaluated for its economic feasibility for biobutanol production from lignocellulosic biomass and industrial waste gases in Phase II.

09 BIOMASS FUELS↗

Conversion of cellulosic biomass-based sugars to mevalonate for downstream chemical upgrading and market development

In collaboration with Visolis, ABPDU researchers have demonstrated a viable path for conversion of cellulosic feedstocks into renewable precursors for commodity fuels and chemicals. This process was demonstrated with equal success for both glucose and xylose conversion. Following proof of concept in 2L bioreactors, the process was scaled and demonstrated in a 50L bioreactor.

09 BIOMASS FUELS↗

Microwave-assisted delignification for improved cellulose production

This study aims to develop microwave (MW) technologies to improve the paper pulping process, decreasing both chemical and thermal energy requirements. The overall objective is to explore an efficient process that aids in the delignification of paper pulp, reducing energy needs and chemical intensity. The experimental variables evaluated during the MW-assisted digestion process include formic acid concentration, time, temperature, digestion cycles, and the formic acid to paper ratio. This research investigates the potential of MW technology to create a more sustainable and efficient cellulose production method.

microwave heating↗

Chemically Cross-Linked Cellulose Nanocrystal Aerogels for Effective Removal of Cation Dye

In this study, porous aerogels were prepared by directional freeze-drying via cross-linking cellulose nanocrystals (CNCs) with poly(methyl vinyl ether-co-maleic acid) (PMVEMA) and poly(ethylene glycol) (PEG). The thermal properties and physical adsorption performance toward cation methylene blue dye of the obtained CNC aerogels were investigated. The maximum degradation temperature was increased from 324°C of CNCs to 355°C of cross-linked CNC aerogels. The dye adsorption isotherm results showed that the maximum methylene blue adsorption capacity of CNC aerogels was 116.2 mg g −1 , according to the Langmuir model, which was mainly due to the electrostatic attractions between negatively charged carboxyl groups or sulfonate groups on the CNC aerogles and cation MB molecules. The reusability test showed that the CNC aerogels contained the same dye adsorption performance in five adsorption/desorption cycles. Overall, this study described an ideal alternative for water purification with high dye adsorption capacity and enhanced physical performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of Carboxymethyl Cellulose as a Thickening Agent for Glauber’s Salt-Based Low Temperature PCM

This work is focused on a novel, promising low temperature phase change material (PCM), based on the eutectic Glauber’s salt composition. To allow phase transition within the refrigeration range of temperatures of +5 °C to +12 °C, combined with a high repeatability of melting–freezing processes, and minimized subcooling, the application of three variants of sodium carboxymethyl cellulose (Na-CMC) with distinct molecular weights (700,000, 250,000, and 90,000) is considered. The primary objective is to optimize the stabilization of this eutectic PCM formulation, while maintaining the desired enthalpy level. Preparation methods are refined to ensure repeatability in mixing components, thereby optimizing performance and stability. Additionally, the influence of Na-CMC molecular weight on stabilization is examined through differential scanning calorimetry (DSC), T-history, and rheology tests. The PCM formulation of interest builds upon prior research in which borax, ammonium chloride, and potassium chloride were used as additives to sodium sulfate decahydrate (Glauber’s salt), prioritizing environmentally responsible materials. The results reveal that CMC with molecular weights of 250 kg/mol and 90 kg/mol effectively stabilize the PCM without phase separation issues, slowing crystallization kinetics. Conversely, CMC of 700 kg/mol proved ineffective due to the disruption of gel formation at its low gel point, hindering higher concentrations. Calculations of ionic concentration indicate higher Na ion content in PCM stabilized with 90 kg/mol CMC, suggesting increased ionic interactions and gel strength. A tradeoff is discovered between the faster crystallization in lower molecular weight CMC and the higher concentration required, which increases the amount of inert material that does not participate in the phase transition. After thermal cycling, the best formulation had a latent heat of 130 J/g with no supercooling, demonstrating excellent performance. This work advances PCM’s reliability as a thermal energy storage solution for diverse applications and highlights the complex relationship between Na-CMC molecular weight and PCM stabilization.

25 ENERGY STORAGE↗

Cellulose Nanofibrils Dewatered with Poly(Lactic Acid) for Improved Bio-Polymer Nanocomposite Processing

Cellulose nanofibrils (CNFs) have theoretically ideal properties for bio-based composite applications; however, the incorporation of these materials into polymers is made challenging by the strong binding of water to CNFs and the irreversible agglomeration of CNFs during drying. Previous methods used “contact dewatering”, wherein the addition of wood flour (WF) to CNFs facilitated the mechanical removal of water from the system via cold pressing, which showed potential in producing dried CNF fibrils attached to wood fibers for biocomposite applications. In this work, the viability of contact dewatering with poly(lactic) acid (PLA) powder for PLA/CNF composites was evaluated. The energy efficiency of dewatering, preservation of nanoscale CNF morphology, and mechanical properties were examined by mixing wet CNFs with pulverized PLA at various loading levels, pressing water out of the system, and compression molding and shear mixing composites for testing. The most impressive results from this dewatering method were the preservation of micron-to-nanoscale fibers with high aspect ratios in PLA-CNF composites; increased strength and modulus of 1.7% and 4.2%, respectively, compared to neat PLA; equivalent or better properties than spray-dried nanocellulose at similar loading levels; and an 11-194x reduction in drying energy compared to spray-drying CNFs.

Chemistry↗

Enhancement of the Physical and Mechanical Properties of Cellulose Nanofibril-Reinforced Lignocellulosic Foams for Packaging and Building Applications

Biobased foams have the potential to serve as eco-friendly alternatives to petroleum-based foams, provided they achieve comparable thermomechanical and physical properties. We propose a facile approach to fabricate eco-friendly cellulose nanofibril (CNF)-reinforced thermomechanical pulp (TMP) fiber-based foams via an oven-drying process with thermal conductivity as low as 0.036 W/(m·K) at a 34.4 kg/m3 density. Acrodur®, iron chloride (FeCl3), and cationic polyacrylamide (CPAM) were used to improve the foam properties. Acrodur® did not have any significant effect on the foamability and density of the foams. Mechanical, thermal, cushioning, and water absorption properties of the foams were dependent on the density and interactions of the additives with the fibers. Due to their high density, foams with CPAM and FeCl3 at a 1% additive dosage had significantly higher compressive properties at the expense of slightly higher thermal conductivity. There was slight increase in compressive properties with the addition of Acrodur®. All additives improved the water stability of the foams, rendering them stable even after 24 h of water absorption.

Chemistry↗