SEARCH · Engineering Papers

Results for “torque control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS2000

Aerothermal Analysis and Design of the Gravity Recovery and Climate Experiment (GRACE) Spacecraft

The Gravity Recovery and Climate Experiment (GRACE) primary mission will be performed by making measurements of the inter-satellite range change between two co-planar, low altitude near-polar orbiting satellites. Understanding the uncertainties in the disturbance environment, particularly the aerodynamic drag and torques, is critical in several mission areas. These include an accurate estimate of the spacecraft orbital lifetime, evaluation of spacecraft attitude control requirements, and estimation of the orbital maintenance maneuver frequency necessitated by differences in the drag forces acting on both satellites. The FREEMOL simulation software has been developed and utilized to analyze and suggest design modifications to the GRACE spacecraft. Aerodynamic accommodation bounding analyses were performed and worst-case envelopes were obtained for the aerodynamic torques and the differential ballistic coefficients between the leading and trailing GRACE spacecraft. These analyses demonstrate how spacecraft aerodynamic design and analysis can benefit from a better understanding of spacecraft surface accommodation properties, and the implications for mission design constraints such as formation spacing control.

Mazanek, Daniel D.↗

NASA NTRS1982

Simulation, flight performance and control of Dynamics Explorers-A and -B spacecraft

This paper presents the results obtained from a study conducted to evaluate the dynamic behavior of Dynamics Explorers-A and -B spacecraft. The effects of environmental torques on the spacecraft motion, momentum buildup due to these torques, and the long appendages on the main body motion are studied using numerical simulations. The numerical results are compared with flight data and are found to be in good agreement. A control philosophy for DE-B to minimize the pitch axis drift is developed. The performance of DE-B in inverted mode and during the inversion maneuver as well as in the normal mode are studied. The spin ripple effect on DE-A due to the long appendages is analyzed and the results are correlated with flight data.

Sellappan, R. G.↗

NASA NTRS1992

Nonlinear modeling of a long flexible manipulator and control by inertial devices

The authors consider the modeling and control of a planar, long flexible manipulator that is representative of current space-based robotic arms. The arm is equipped with three actuators: 1) a shoulder motor; 2) a torque wheel at the tip; and 3) a proof-mass actuator at the tip. The goal is to investigate the potential use of inertial devices as control inputs for maneuvering tasks and vibration suppression. The parameters used for the inertial devices at the tip are comparable to those specified for the Mini-Mast facility at the Langley Research Center. A nonlinear distributed parameter model is obtained by the extended Hamilton principle. The associated eigenvalue/eigenfunction problem is solved and a finite-dimensional state space model is assembled. A preliminary design of a linear quadratic regulator is used, and computer simulation results illustrate the benefits of using the proposed actuators.

Barbieri, Enrique↗

NASA NTRS1989

Electronically Variable Pressure Regulator (EVPR)

A new programmable electronically variable pressure regulator (EVPR) concept accurately controls the local outlet or remote system pressure. It uses an integral pulse width modulated rare earth permanent magnet motor operating in response to redundant pressure transducer feedback signals. The EVPR is a simple single stage device that does not use dynamic seals or pilot valving. Conversion of partial revolution motor torque to poppet lifting force is accomplished by pure flexure action to avoid using bearings. The flexure drive (called the ROTAX) has a variable lead to minimize motor weight and power consumption. Breadboard tests were completed successfully on two critical design elements of the EVPR: the ROTAX and the motor. The ROTAX cable system was tested for 250,000 cycles without failure. The breadboard motor met the basic design requirements including the design torque and power consumption. Prototype parts were fabricated, and testing of the prototype EVPR has started. It is PC computer controlled to facilitate programming, data acquisition and analysis. A lightweight dedicated microprocessor is planned for the flightweight EVPR.

Reinicke, R. H.↗

NASA NTRS1993

Precision slew/settle technologies for flexible spacecraft

Many spacecraft missions in the next decade will require both a high degree of agility and precision pointing. Agility includes both rotational maneuvering for retargeting and translational motion for orbit adjustment and threat avoidance. The major challenge associated with such missions is the need for control over a wide range of amplitudes and frequencies, ranging from tens of degrees at less than 1 Hz to a few micron radians at hundreds of Hz. TRW's internally funded Precision Control of Agile Spacecraft (PCAS) project is concerned with developing and validating in hardware the tools necessary to successfully complete the combined agile maneuvering/precision pointing missions. Development has been undertaken on a number of fronts for quietly slewing flexible structures. Various methods for designing slew torque profiles have been investigated. Prime candidates for slew/settle scenarios include Inverse Dynamics and Parameterized Function Space. Joint work with Processor Bayo at the University of California, Santa Barbara and Professor Flashner at the University of Southern California has led to promising torque profile design methods. Active and passive vibration suppression techniques also play a key role for rapid slew/settle mission scenarios. Active members with local control loops and passive members with high loss factor viscoelastic material have been selected for hardware verification. Progress in each of these areas produces large gains in the quiet slewing of flexible spacecraft. The main thrust of the effort to date has been the development of a modular testbed for hardware validation of the precision control concepts. The testbed is a slewing eighteen foot long flexible truss. Active and passive members can be interchanged with the baseline aluminum members to augment the inherent damping in the system. For precision control the active members utilize control laws running on a high speed digital structural control processor. Tip and midspan motions of the truss are determined using optical sensors while accelerometers can be used to monitor the motions of other points of interest. Preliminary results indicate that a mix of technologies produces the greatest benefit. For example, shaping the torque profile produces large improvements in slew/settle performance, but without added damping settling times may still be excessive. With the introduction of moderate amounts of damping, slew/settle performance is vastly improved. On the other hand, introducing damping without shaping the torque profile may not yield the desired level of performance.

Manning, R. A.↗

NASA NTRS1970

Electronically controlled motor drive system has ultra-high reliability and long lifetime

Direct drive electromechanical system is composed of brushless dc torque motor, offset-tooth magnetic sensor that derives position and rate information directly from output shaft, and rotary power transformer that transfers electrical power from external source to proper load. System has high servo loop stiffness and minimum power consumption.

Veillette, L. J.↗

NASA NTRS2013

Next-Generation Maneuvering System with Control-Moment Gyroscopes for Extravehicular Activities Near Low-Gravity Objects

Looking ahead to the human exploration of Mars, NASA is planning for exploration of near-Earth asteroids and the Martian moons. Performing tasks near the surface of such low-gravity objects will likely require the use of an updated version of the Manned Maneuvering Unit (MMU) since the surface gravity is not high enough to allow astronauts to walk, or have sufficient resistance to counter reaction forces and torques during movements. The extravehicular activity (EVA) Jetpack device currently under development is based on the Simplified Aid for EVA Rescue (SAFER) unit and has maneuvering capabilities to assist EVA astronauts with their tasks. This maneuvering unit has gas thrusters for attitude control and translation. When EVA astronauts are performing tasks that require ne motor control such as sample collection and equipment placement, the current control system will re thrusters to compensate for the resulting changes in center-of-mass location and moments of inertia, adversely affecting task performance. The proposed design of a next-generation maneuvering and stability system incorporates control concepts optimized to support astronaut tasks and adds control-moment gyroscopes (CMGs) to the current Jetpack system. This design aims to reduce fuel consumption, as well as improve task performance for astronauts by providing a sti er work platform. The high-level control architecture for an EVA maneuvering system using both thrusters and CMGs considers an initial assessment of tasks to be performed by an astronaut and an evaluation of the corresponding human-system dynamics. For a scenario in which the astronaut orbits an asteroid, simulation results from the current EVA maneuvering system are compared to those from a simulation of the same system augmented with CMGs, demonstrating that the forces and torques on an astronaut can be significantly reduced with the new control system actuation while conserving onboard fuel.

Carpenter, Michele↗

NASA NTRS1991

Proximity operations considerations affecting spacecraft design

Proximity operations can be defined as the maneuvering of two or more spacecraft within 1 nautical mile range, with relative velocity less than 10 feet per second. The passive vehicle is nontranslating and should provide for maintenance of the desired approach attitude. It must accommodate the active (translating) vehicle induced structural loads and performance characteristics (mating hardware tolerances), and support sensor compatibility (transponder, visual targets, etc.). The active vehicle must provide adequate sensor systems (relative state information, field-of-view, redundancy), flight control hardware (thruster sizing, minimal cross-coupling, performance margins, redundancy) and software (reconfigurable, attitude/rate modes, translation and rotation fine control authority) characteristic, and adequate non-propulsive consumables such as power. Operational concerns must be considered. These include the following: (1) the desired approach trajectory and relative orientation; (2) the active vehicle thruster plume effects (forces, torques, contamination) on the passive vehicle; and (3) procedures for contingencies such as loss of communications, sensor or propulsion failures, and target vehicle loss of control.

Staas, Steven K.↗

NASA NTRS1981

Command profile for Galileo scan platform control

A recursive command profile is developed for the control of a two-degree-of-freedom scan platform mounted on a flexible structure. Perfect sensors and actuators are assumed for development and testing, and structural vibrations are minimized by actuator torque commands following a smooth torque-time profile. The integral of the smooth torque profile, the rate profile, is recursively generated by a piecewise constant second derivation, and the torque applied by the closk actuator is divided into three components. Results show that the smooth platform motion in response to the command profiles is what the Galileo control systems needs to avoid stator structural vibrations. Position, rate and acceleration profiles are also presented, and the resulting motion of the scan platform in response to command profiles is illustrated.

Man, G. K.↗

NASA NTRS1973

Guiding of a balloon-borne coronagraph

Discussion of the guidance system of a balloon-borne coronagraph designed for IR solar corona observations at an altitude of 36 km. The coronagraph has two telescopes, measures 6 m in length, weighs 73 kg, is stabilized by a three-axis system, and has a pointing precision of plus or minus 10 sec of arc. Three torque motors are used to activate the tracking servo system of the coronagraph. An integral control system is used to prevent a permanent instrumental error. The coronagraph has been tested in two balloon missions.

Li, T.-C.↗

NASA NTRS1974

The AIROscope pointing and stabilization system

The AIROscope pointing and stabilization system is described. The system is configured with three gimbal axes and rate integrating gyro stabilization to provide a stable platform for infrared astronomy. Error signals for on and off-axis pointing are derived from a video sensor which also drives a ground station display. Other features of the system include direct drive torque motors and electronic suspension damping. Results of analysis and simulations used to design the control loops, and a pointing error analysis are presented.

Murphy, J. P.↗

NASA NTRS1978

Correlation tracking for a Planetary Pointing and Tracking System

The Planetary Pointing and Tracking System (PPTS) is being developed to provide precision pointing for science platforms on future autonomous planetary spacecraft. The PPTS design approach using a CCD optical sensor for closed-loop control with respect to the target body, a gyro for inertial stabilization, and brushless dc torque motors for smooth and continuous platform articulation is essential for high resolution planetary imaging and automated science execution. An integral part of PPTS is the correlation tracker which has the potential to revolutionize autonomous guidance.

Assefi, T.↗

NASA NTRS1983

The dynamics and control of large flexible space structures, 6

The controls analysis based on a truncated finite element model of the 122m. Hoop/Column Antenna System focuses on an analysis of the controllability as well as the synthesis of control laws. Graph theoretic techniques are employed to consider controllability for different combinations of number and locations of actuators. Control law synthesis is based on an application of the linear regulator theory as well as pole placement techniques. Placement of an actuator on the hoop can result in a noticeable improvement in the transient characteristics. The problem of orientation and shape control of an orbiting flexible beam, previously examined, is now extended to include the influence of solar radiation environmental forces. For extremely flexible thin structures modification of control laws may be required and techniques for accomplishing this are explained. Effects of environmental torques are also included in previously developed models of orbiting flexible thin platforms.

Bainum, P. M.↗

NASA NTRS1984

Magnetic suspension and balance system study

A compact design for a superconducting magnetic suspension and balance system is developed for a 8 ft. x 8 ft. transonic wind tunnel. The main features of the design are: a compact superconducting solenoid in the suspended airplane model; permanent magnet wings; one common liquid helium dewar for all superconducting coils; efficient new race track coils for roll torques; use of established 11 kA cryostable AC conductor; acceptable AC losses during 10 Hz control even with all steel structure; and a 560 liter/hour helium liquefier. Considerable design simplicity, reduced magnet weights, and reduced heat leak results from using one common dewar which eliminates most heavy steel structure between coils and the suspended model. Operational availability is thought to approach 100% for such magnet systems. The weight and cost of the magnet system is approximately one-third that of previous less compact designs.

Boom, R. W.↗

NASA NTRS1988

Position And Force Control For Multiple-Arm Robots

Number of arms increased without introducing undue complexity. Strategy and computer architecture developed for simultaneous control of positions of number of robot arms manipulating same object and of forces and torques that arms exert on object. Scheme enables coordinated manipulation of object, causing it to move along assigned trajectory and be subjected to assigned internal forces and torques.

Hayati, Samad A.↗

NASA NTRS1988

Flexible spacecraft maneuver - Inverse attitude control and modal stabilization

A control law is presented for three-axis rotational maneuvers of a spacecraft (orbiter)-beam-tip body (antenna or a reflector) configuration based on nonlinear inversion and modal velocity feedback. Using invertibility and functional reproducibility results, a decoupling attitude control law is presented such that, in the closed-loop system, the attitude angles of the spacecraft are independently controlled using the control moments acting on the space vehicle. This controller asymptotically decouples the flexible dynamics from the rigid one and also allows the decomposition of the elastic dynamics into two subsystems representing the transverse deflections of the beam in two orthogonal planes. These low-order subsystems are used for derivation of a modal velocity feedback stabilizer using the force and moment actuators at the end body. Simulation results are presented to show that, in the closed-loop system, attitude control and elastic mode stabilization are accomplished in spite of the parameter uncertainty and disturbance torque input in the system.

Singh, Sahjendra N.↗

NASA NTRS1989

Compliant Robot Wrist Senses Deflections And Forces

Precise parts assembled without damage. Goddard Space Flight Center developed compliant wrist that moves in any direction and rotates about any axis in response to applied forces. Deflection calibrated and instrumented so control computer measures degree of deflection and derives magnitude and direction of applied forces and torques. Compliant wrist brings to robots important capabilities humans use in manipulating objects. Helps prevent damage to precise, delicate parts during assembly by robot. Rod lengths, spring stiffnesses, and type of displacement sensor changed to suit different applications.

Purves, Lloyd R.↗

NASA NTRS1988

An advanced actuator for high-performance slewing

A conceptual design for an advanced momentum exchange actuator for application to spacecraft slewing is described. The particular concept is a magnetically-suspended, magnetically gimballed Control Moment Gyro (CMG). A scissored pair of these devices is sized to provide the torque and angular momentum capacity required to reorient a large spacecraft through large angle maneuvers. The concept described utilizes a composite material rotor to achieve the high momentum and energy densities to minimize system mass, an advanced superconducting magnetic suspension system to minimize system weight and power consumption. The magnetic suspension system is also capable of allowing for large angle gimballing of the rotor, thus eliminating the mass and reliability penalties attendant to conventional gimbals. Descriptions of the various subelement designs are included along with the necessary system sizing formulation and material.

Downer, James↗