SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Several arrays were designed and tested. Tests included vibrational and acoustical tests, radiant heating tests, and thermal conductivity tests. A feasible manufacturing technique was established for producing the protection system panels.
Explore the source record for details and available documents.
Several techniques have been used to study pretreated Ti 6-4 surfaces including scanning electron microscopy (SEM), electron spectroscopy of chemical analysis (ESCA), and, reflectance visibile spectroscopy. Each pretreatment type gives a characteristic surface morphology as seen by SEM. Elemental analysis of the Ti 6-4 surfaces was done using ESCA. Trace residual contaminants from particular chemical pretreatments are identified readily. Reflectance visible spectroscopy using indicator dyes placed on Ti 6-4 surfaces appears to be a feasible approach to establish surface acidity. Differences in surface acidity have been observed using bromthymol blue on Ti 6-4 surfaces pretreated by two different methods.
A method is described for fabricating curved T1-6Al-4V multiwall panels having a single radius of curvature of 30.5 cm (12 inches). A panel 30.5 x 30.5 x 1.7 cm (12 x 12 x .688 inch) having 4 dimpled sheets, 5 undimpled sheets, and stepped side closures was designed, fabricated and delivered for evaluation. Tool design for skin and dimpled sheet forming are described as well as layup and liquid interface diffusion bonding.
Previous measurements of the specific heat of V-doped Ti2O3 at low temperatures were explained by a model which also suggested the material would have a high thermoelectric figure-of-merit. The sample preparation, experimental apparatus, and the results of measurements on the thermal conductivity, thermoelectric power, and electrical resistivity of a single crystal Ti2O3 - 4% V sample are described. The results are used to derive the thermoelectric figure-of-merit between 5 and 300 K. The figure-of-merit is much smaller than expected and of little practical value because of the very high phonon thermal conductivity.
Development efforts have been undertaken to improve the processing and structural efficiencies of advanced cold-formable beta Ti alloys, using the standard, hot-formed and rivetted construction of Ti-6Al-4V sheet structures as a basis for comparison. Ti-15V-3Cr-3Al-3Sn (Ti-15-3) beta alloy is formable, brazable and weldable in the solution-treated condition, and after aging displays mechanical properties suitable for postulated service in the -65 to 600 F temperature range. A novel methodology using cold-formed Ti-15-3 stringers and Ti-6Al-4V face sheets that are joined by means of an out-of-furnace isothermal brazing process, followed by low temperature aging, can reduce production costs by as much as 28 per cent. Structural efficiency has been demonstrated in room and elevated temperature crippling tests of small skin-stringer assemblies.
(Previously announced in STAR as N82-20551)
Wet coating mixture composed of graphite pigment potassium silicate binder solution and distilled water. Resulting coating has electrical resistivity of less than 10 to the 6th power ohm-cm.
Scanning electron microscope/X-ray photoelectron spectroscopy (SEM/XPS) analysis of fractured adhesively bonded Ti 6-4 samples is discussed. The text adhesives incuded NR 056X polyimide, polypheylquinoxaline (PPQ), and LARC-13 polyimide. Differentiation between cohesive and interfacial failure was based on the absence of presence of a Ti 2p XPS photopeak. In addition, the surface oxide layer on Ti-(6A1-4V) adherends is characterized and bond strength and durability are addressed. Bond durability in various environmental conditions is discussed.
Studies of Ti isotopic compositions have shown that virtually every Ca-Al-rich Allende inclusion contains anomalous Ti. The present investigation is concerned with the results of a study of Ti isotopic compositions in meteorites. One objective of the study is to evaluate the possibility of a relation between oxygen and Ti anomalies, while another objective is to explore questions regarding the origin of the Ti anomalies. A summary of the major experimental findings of the study of Ti isotopic compositions is also presented. It is noted that an assessment of the implications of the Ti results favors a chemical memory type of model in which products from various nucleosynthetic sources survive in mineral grains. Isotopic heterogeneities are then preserved due to incomplete mixing and/or equilibriation with the bulk of solar system matter. Strong arguments are found to exist against a pure late supernova injection model.
Potential tooling pickup not acceptable on sandwich panels that have face sheets 0.016 in. (0.41 mm) thick. In this application, problem eliminated by changing tooling slipsheet from type 321 CRES to type 430 stainless steel and coating both slipsheet and face sheet with boron nitride powder and binder thinned in acetone.
The dc glow discharges in different gas mixtures of Ar + N2, Ar + NH3 or Ar + N2 + H2 result in the surface nitriding of Ti metal and its alloy (Ti6Al4V). Various gas mixtures were used in order to establish the main active species governing the nitriding process, i.e., N, N2, NH, or NH2 as excited or ionized particles. The dc discharge was sampled and analyzed by quadruple mass spectrometry (QPMS) and optical emission spectroscopy (OES), and the nitrided samples were analyzed by scanning electron microscopy (SEM) with an EDAX attachment, microhardness, and Fourier transform infrared reflectance spectrometry (FTIR). It was found that the excited and ionized nitrogen and hydrogen atoms are the main species responsible for the nitriding process in a dc glow discharge.
Metallurgical and mechanical changes occurring during high-speed rubbing of Ti-6Al-4V blade specimens against an abradable Nichrome aircraft engine seal material were studied using optical microscopy, electron microscopy, and microhardness techniques. Evidence of temperatures above the beta transus of Ti-6Al-4V (1000 C) and of thermal hardening was found on blade tips that exhibited undesirable abrading characteristics resulting in high forces of interaction, high temperatures, and smearing. The material within the layer of the corresponding seals was found to be work-hardened to a depth of about 0.1 mm and showed evidence of densification extending to a depth of about 0.5 mm below the rubbed surface. Wear particles produced by rub interactions that generated cleanly abraded seal surfaces were found to be several times larger than those produced during interactions which showed evidence of surface smearing and seal densification.
To understand the mechanical properties of fiber-reinforced composite materials, it is necessary to understand the mechanical properties of the matrix materials and of the reinforcing fibers. Another factor that can affect the mechanical properties of a composite material is the interaction between the fiber and the matrix. In general, composites with strong fiber matrix bonding will give higher modulus, lower toughness composites. Composites with weak bonding will have a lower modulus and more ductility. The situation becomes a bit more complex when all possibilities are examined. To be considered are the following: the properties of the surface layer on the fiber, the interactive forces between polymer and matrix, the surface roughness and porosity of the fiber, and the morphology of the matrix polymer at the fiber surface. In practice, the surface of the fibers is treated to enhance the mechanical properties of a composite. These treatments include anodization, acid etching, high temperature oxidation, and plasma oxidation, to name a few. The goal is to be able to predict the surface properties of carbon fibers treated in various ways, and then to relate surface properties to fiber matrix bonding.
Carbon fibers were obtained from several manufacturers. Surface treatments were performed on these fibers by anodization. The surfaces of these fibers were analyzed by X-ray photoelectron spectroscopy and wetting force measurement. The breaking strength of these fibers was measured at 2.5 cm length. It was seen that the surface treatments reduces the strength of the fibers. It was also seen that the Hercules fibers had a higher breaking strength than the Union Carbide fibers. Fiber critical length measurements showed no difference in critical lengths between AS-4 and AU-4 fibers embedded in polysulfone. However, the fiber lengths were much shorter for the surface treated fibers. This effect could be related to increased adhesion between fiber and matrix, or it could be due to the lower breaking strength of the surface treated fiber.
A study is conducted of the use of aluminum coatings as oxidation retardants for Ti alloys, using room temperature normal emittance and spectral emittance as bases for the characterization of oxidation properties with and without the coatings. Thermal exposures were conducted in a thermogravimetric analysis apparatus in which specimen weight was continuously monitored. The results obtained indicate that the weight gains are proportional to the square root of the time for uncoated alloys and for 649 C-exposed aluminum-coated alloys. For the 704 C-exposed aluminum-coated alloys, weight gain exhibits a low rate for short and a high rate for long exposure times, implying that the 0.5-micron coating's protection decreases for long exposures at this temperature.
The present investigation is concerned with the mutual influence of creep and fatigue in the case of Ti-6211, which represents a new weldable, stress-corrosion resistant alloy. Attention is given to the effect of creep on fatigue, the effect of fatigue on creep, and microstructural studies. It is found that prior creep in the amounts investigated, from 0.2 percent to 2.7 percent, is beneficial to low-cycle fatigue life. Hold time at peak strain is found to be beneficial to low-cycle fatigue life. Hold time at constant stress has no effect on low-cycle fatigue when specimens are cycled only once between hold times; but increasing fatigue loading for 50 or more cycles between hold times can prolong the fatigue life. There is an acceleration of creep by cyclic loading when comparison of cyclic and static creep is based on mean stress.
Explore the source record for details and available documents.