Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Final Report UCLA-Thermochemical Storage with Anhydrous Ammonia

In ammonia-based thermochemical energy storage (TCES), ammonia is dissociated endothermically as it absorbs solar energy during the daytime. When energy is required, the reverse reaction releases energy to heat a working fluid such as steam, to produce electricity. Ammonia-based TCES has great advantages of simplicity, low cost reactants, and a strong industrial base in the conventional ammonia industry. The concept has been demonstrated over three decades of research at Australian National University, achieving a 24-hour demonstration of a complete system. At the start of this project, three challenges were identified that would have to be addressed to show that the system is technically and economically viable for incorporation into a CSP plant with an advanced, high temperature power block. All three of these challenges have now been addressed: 1. The ammonia synthesis reaction had not, to our knowledge, been carried out at temperatures consistent with modern power blocks (i.e., ~650°C). The technical feasibility of operating a reactor under high-temperature, near-equilibrium conditions was an unknown, and was therefore a technical risk. The project has successfully demonstrated steam heating to 650°C and energy recovery to steam at the 5 kWt level. 2. The ammonia system has a relatively low enthalpy of reaction combined with gas phase reactants. This is not a direct disadvantage since the reactants themselves are low cost. The challenge lies in storing the required volume of reactants cost effectively. Therefore, a second key goal was to show, through techno-economic analysis, that underground storage technologies can be used to store the energy-rich gas at a cost that is consistent with the SunShot cost goal. We have identified two promising technologies for gas storage: storage in salt caverns has an estimated cost of 1(USD)/kWht and storage in drilled shafts could be on the order of 7(USD)/kWht. Together these two options answer the technical challenge associated with storage of gas phase components. 3. While this project is primarily concerned with high-temperature heat recovery and methods to store the gaseous components, it is also important to consider the feasibility of the entire system. Consequently, an additional goal was to perform analysis to show the feasibility of integrating endothermic reactors within a tower receiver. A conceptual design of an ammonia dissociation receiver/reactor has been developed that fits into the same size cylindrical envelope as the molten salt receiver in SAM, and has the same design thermal capacity. The calculated thermal efficiency of this receiver is 94.6%. Thus, this investigation has established the technical feasibility of a surround field tower system using ammonia dissociation. With these challenges addressed, we proceeded to design a full-scale synthesis and heat recovery system. A model was developed and validated by comparison with our experimental data. A parametric study showed, among other things, the importance of using small tube diameters and spacing to enhance heat transfer. Multi-parameter optimization was used to find a design that minimizes the wall material volume. Finally, cost estimation shows that the ammonia system has good prospects of meeting the Sunshot 15(USD)/kWht target: estimated costs of the entire synthesis system for the 220 MWt plant with 6 hours of storage are 13(USD)/kWht using salt cavern storage and 18(USD)/kWht using shaft drilling. Costs per kWht are even lower with more hours of storage. With the established technology of ammonia synthesis as a starting point, the successes of the project have mitigated technical risks associated with high-temperature synthesis reaction, underground storage, and tower receiver design. Estimated costs are less than 15(USD)/kWht with salt cavern storage. It is now possible to map a time line to commercial deployment that is likely to be shorter and less risky than other thermochemical cycles under active investigation. UCLA has filed a patent that protects the new ideas developed during this project. Discussions are ongoing with potential investors with the aim of partnering for further work. As well as immediate improvements and extra work with the existing experimental system, a key goal is to extend it to a small solar-driven project at an early opportunity.

14 SOLAR ENERGY↗

Lab-scale Development of a Hybrid Capture System with Advanced Membrane, Solvent system, and Process Integration

The objective of the project is to achieve lab-scale demonstration of a transformational hybrid membrane/solvent system for the capture of CO 2 from flue gas. A novel process integration scheme was proposed to overcome the low partial pressure of CO 2 present in flue gas. This scheme takes advantage of the potential synergies inherent in the membrane and solvent capture systems. The proposed hybrid technology replaces the second-stage membrane with a solvent capture process. The combustion air is used as a sweeping gas in the solvent stripper. This overall configuration has the major advantages of requiring much less air and eliminating the problems associated with oxygen slip in the membrane-based systems. Even more importantly, because of the presence of the air sweep in the stripper, much lower temperatures are required for solvent regeneration, which enables heat integration to the point that no process steam is required. This project was to perform lab-scale demonstration of Liquid Ion Solutions (LIS) transformational hybrid membrane/solvent system for post-combustion CO 2 capture while demonstrating significant progress toward achievement of the overall fossil energy performance goals of 90% CO 2 capture rate with 95% CO 2 purity at a cost of electricity 30% less than baseline capture approaches. This report is written chronologically based on budget periods. Each budget period discusses the work performed and its results. At the end of each budget period the milestone charts are provided to show the progress. This project was not able to meet its stated goals. The performances of the power plant equipped with the hybrid process and Baseline Case B12B were compared. The simulation results showed that the power plant equipped with hybrid CO2 capture process has an improved thermal efficiency of 33.4% compared to the Baseline Case B12B, which is 32.5%. However, the COE for the hybrid process is $146.3/MWh which is higher than the $142.8/MWh for Case B12B. If this process were to be applied as a retrofit, it may make sense to use this configuration as it does not require any change in an existing plant configuration and steam cycle. However, for a new powerplant the capital cost is higher than the Case B12B. On the membrane development side, we successfully showed that interfacially-controlled envelope (ICE) membranes work. The inclusion of surface modified nano-particles results in much higher gas diffusivities. The Gen-1 ICE membrane developed under this project showed exceptional improved permeability for CO 2 . However, we ran into major problems which were associated with the scalability and reproducibility of the poly(phosphozene) polymers. The issues with scale-up are and batch to batch variability is also discussed. At the end of this report we have provided our recommendations on materials development for better membrane materials and alluded to the use of much simpler chemistry while keeping the concept of ICE membrane intact. It is also clear that vacuum and compression equipment is costly. If a process which can eliminate the use of vacuum and compression equipment would significantly decrease the overall cost of capture. Some thoughts regarding such system is also provided in the outlook portion of this report.

20 FOSSIL-FUELED POWER PLANTS↗

Lean Miller Cycle System Development for Light-Duty Vehicles (Final Report)

This report summarizes activities conducted in support of the project “Lean Miller Cycle System Development for Light-Duty Vehicles” under Cooperative Agreement Number DE-EE0006853. In order to accomplish the government objective of achieving breakthrough thermal efficiencies while meeting U.S. EPA emission standards, this project focused on combining two enabling technologies in a gasoline engine: lean combustion and “Miller Cycle.” Lean combustion is thermodynamically more efficient than stoichiometric combustion but requires a more complex exhaust aftertreatment system compared to a traditional three-way catalyst system. The “Miller Cycle” concept increases expansion of combustion gases to extract additional work, reduces pumping losses, and increases efficiency. The objective of the project was to research, develop, and demonstrate the new Lean Miller Cycle (LMC) combustion concept to achieve a 35% improvement in fuel economy over a 2010 production baseline vehicle. The baseline vehicle chosen was a Chevrolet Impala equipped with a 3.5L V6 port-fuel injected naturally-aspirated engine, a four-speed automatic transmission with a peak-power and -torque of 157 kW and 290 N-m respectively. The enabling technologies were developed and demonstrated on a single cylinder engine and then integrated into a multicylinder engine and aftertreatment system. Along with achieving the efficiency targets, the downsized boosted LMC engine system was projected to achieve a peak-power and –torque of 172 kW at 354 Nm respectively exceeding the baseline engine performance. The multicylinder engine was optimized and calibrated over a set of steady-state operating points on an engine dynamometer. The target of the project was a 35% improvement in combined city/highway fuel economy at SULEV30 tailpipe emissions over the baseline vehicle. The project achieved a projected 42.4% from the vehicle drive cycle analysis assuming no penalty for management of the lean-aftertreatment system. This penalty was projected to fall within the fuel economy margin achieved and include control and calibration compromises for catalyst heating, NH3 formation for lean-NOx SCR and drive quality. A final vehicle demonstration was planned where emissions, drivability and performance were to be confirmed. Four decision gates were set up annually with deliverables to assess progress and determine whether status to deliverables warranted project continuation through the final vehicle demonstration. The project was closed in June 2019 at the end of budget period three after not passing the third decision gate due to projected system costs prohibiting economic feasibility in the light-duty vehicle industry landscape. However, the project’s efficiency targets were achieved by validation through steady-state dynamometer testing of the multicylinder engine.

33 ADVANCED PROPULSION SYSTEMS↗

Cloud Condensation Nuclei Particle Counter Instrument Handbook - Airborne Version

The cloud condensation nuclei counter (CCN) is a U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) user facility instrument for measuring the concentration of aerosol particles that can act as cloud condensation nuclei. Note: ARM deploys both ground and airborne versions of this instrument. This handbook covers only the airborne instrument; the ground version is covered by DOE/SC-ARM-TR-168. The main differences between the two are that the airborne CCN operates at fixed supersaturation and adapts thermal efficiency calculation in the data process. The CCN draws sample aerosol through a column with thermodynamically unstable supersaturated water vapor that can condense onto aerosol particles. Particles that are activated, i.e., grown larger in this process, are counted (and sized) by an optical particle counter (OPC). Thus, activated ambient aerosol particle number concentration as a function of supersaturation is measured. Models CCN-100 and CCN- 200 differ only in the number of humidifier columns and related subsystems: CCN-100 has one column and CCN-200 has two columns along with dual flow systems and electronics.

54 ENVIRONMENTAL SCIENCES↗

Embedment of sensors in ceramic structures

Ceramic materials such as silicon carbide (SiC) are attractive for many nuclear applications due to their ability to withstand high temperatures, which inherently improve the thermal efficiency of the power conversion cycle and can in some cases provide high-temperature process heat. SiC is particularly attractive because of its high-temperature strength retention, stability under neutron irradiation, and low neutron absorption. The TCR program has recently demonstrated the ability to fabricate monolithic SiC components with complex geometries using a binder jet additive manufacturing technique followed by densification using chemical vapor infiltration (CVI). This technology presents an opportunity to embed sensors within ceramic components at critical locations that allow for enhanced process monitoring and control of advanced nuclear energy systems. The challenges with embedding sensors in ceramic components are to identify appropriate materials that can survive the CVI process, remain embedded after cooling to room temperature, and be suitable for operation in a high-temperature nuclear environment. This report summarizes the sensors that are being considered for embedding within ceramics, the sensor embedding process, material compatibility studies, and characterization of the embedded components. Material selection is first guided by computational thermodynamics and is confirmed by embedding coupons and examining material interactions using electron microscopy. This work shows that a wide range of refractory metals, as well as certain fiber optic sensors, can be successfully embedded in 3D-printed SiC. Future work will involve testing of functional sensors including thermocouples and optical fiber-based, spatially distributed temperature/strain sensors.

36 MATERIALS SCIENCE↗

Molten Salt Reactor Signatures and Modeling Study

Molten salt reactor (MSR) technologies, either liquid fueled and cooled or only liquid cooled, pose specific, unique challenges for safeguards of the special nuclear material during the operation, fueling, and maintenance of the reactor. MSRs are one type of Generation IV technologies being invested in and considered for U.S. domestic fabrication primarily for electricity and process heat production. These designs have generated growing commercial interest for several reasons, including high (≈40%) thermal efficiency, ease of fueling, improved use of uranium fuel, potential utilization of thorium fuel, and proposed inherent safety features. U.S. companies have several planned designs that differ in fuel, cooling, and neutron energy spectrum. Driven by commercial interest and the intent of licensing MSRs, the U.S. Nuclear Regulatory Commission (NRC) has developed a vision and strategy to accommodate non-light water reactors (LWR), which include MSRs (U.S. Nuclear Regulatory Commission 2019). In addition, the Department of Energy (DOE) through the Office of Nuclear Energy (NE) Office of Advanced Reactor Technologies (ART), …sponsors research, development and deployment (RD&D) activities through its Next Generation Nuclear Plant (NGNP), Advanced Reactor Concepts (ARC), and Advanced Small Modular Reactor (aSMR) programs to promote safety, technical, economical, and environmental advancements of innovative Generation IV nuclear energy technologies. Reactor types considering the use of salts, liquid metals, or gases for coolant fall under both ARC and aSMR. Therefore, Research Design & Development is being pursued by DOE-NE through national laboratories, universities, and international and industrial collaborations. Additionally, the U.S. is a member of the Gen IV International Forum (GIF). The GIF is a cooperative, multinational organization to guide and carry out research and development needed for the GEN IV reactor systems (Forum 2018). GIF evaluated numerous reactor concepts and down-selected to the six most feasible advanced reactor technologies: gas-cooled fast reactor (GFR), lead-cooled fast reactor (LFR), MSR, supercritical watercooled reactor (SCWR), sodium-cooled fast reactor (SFR), and very high temperature reactor (VHTR). In support of the growing interest domestically and internationally, the Materials Protection, Accounting, and Control Technologies (MPACT) campaign, under the DOE-NE Fuel Cycle Technologies (FCT) program, engages in R&D activities by developing advanced instrumentation and analysis for safeguards and security of modern, advanced nuclear fuel cycle (non-LWR) facilities. Because of the historic experience in the operation of the Aircraft Reactor Experiment (ARE) and the Molten Salt Reactor Experiment (MSRE) (Robertson, MSRE Design and Operations Report Part I 1965), Oak Ridge National Laboratory (ORNL) is heavily engaged in the various R&D activities through the DOE complex related to MSRs including national technical leadership of the DOE-NE MSR campaign. This report discusses and presents the outcomes of the FY19 MPACT MSR Safeguards task. The challenges presented by MSRs for nuclear material accountancy and control (NMAC) and associated safeguards will be investigated. The objective of this research is to explore and compile the safeguards requirements and identify measurement signatures through an initial high-level MSR design and develop complementary advanced simulation and modeling capabilities. A high-level ORNL-developed MSR design called the Molten Salt Demonstration Reactor (MSDR) (Bettis, Alexander and Watts 1972) was used as the target reactor design for this research. The MSDR model incorporates technology from the MSRE and the Molten Salt Breeder Reactor (Robertson, Conceptual Design of a Single-Fluid Molten-Salt Breeder Reactor 1971). But the MSDR is a 750 MWth graphite moderated liquid fueled (low-enriched uranium) MSR compared to the MSRE’s of 7.5 MWth. The focus of this report is to discuss the evaluation of novel signatures, correlations, and indicators to understand the applicability of current safeguards instrumentation to MSRs using the modeling results from the MSDR.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Superficial Carbon Dioxide Brayton Cycle Energy Conversion Research and Development Program

A closed Brayton cycle recirculates the working fluid, and the turbine exhaust is used in a recuperating heat exchanger to heat the turbine feed. A "supercritical cycle' is a closed Brayton cycle in which the working fluid, such as supercritical carbon dioxide (s-0O2), is maintained near the critical point during the compression phase of the cycle. The key property of the fluid near its critical point is its higher gas density, closer to that of a liquid than of a gas, allowing for the pumping power in the compressor to be significantly reduced, which results in thermal efficiency that is significantly improved over the efficiency attainable in an ideal-gas Brayton cycle. Another advantage of using a supercritical cycle is that the overall footprint of the power-conversion system can be significantly reduced, as compared to the same power output of a steam-Rankine cycle, due to the high pressure in the system and resulting low volumetric flow rate. This allows for the heat-rejection heat exchanger and turbine to be orders of magnitude smaller than for similar power output steam-Rankine systems. Other potential advantages are the reduced use of water, not only due to the increased efficiency, but due also to the fact that the heat rejection temperature is significantly higher than for steam-Rankine systems, allowing for significant heat rejection directly to air. In 2006, Sandia National Laboratories (SNL), recognizing these potentially significant advantages of a higher efficiency power cycle, used internal funds to establish a testing capability and began partnering with the U.S. Department of Energy Office of Nuclear Energy to develop a laboratory-scale test assembly to show the viability of the underlying science and demonstrate system performance. Since that time, SNL has generated over 100 kW-hours of energy, verified cycle performance, and developed cycle controls and maintenance procedures. The test assembly has successfully operated in different configurations (simple Brayton, waste heat cycle, and recompression) and tested additives to the s-CO 2 working fluid. However, challenges remain to confirm viability of existing components and suitability of materials, demonstrate that theoretical efficiencies are achievable, and integrate and scale up existing technologies to be suitable for a range of applications.

42 ENGINEERING↗

Production and Chemical Analysis of NaCl-KCl-UCl 3 Salts

Thermochemical and thermophysical properties of several molten salt systems of interest to molten salt reactor (MSR) developers are being measured at Argonne National Laboratory. These properties are needed by developers to design, license, and operate their reactors. Thermochemical properties being measured at Argonne include thermal transitions, phase behavior, and heat capacity. Thermophysical properties being measured at Argonne include liquid density, surface tension, volumetric thermal expansion of the liquid phase, thermal diffusivity, thermal conductivity, and viscosity. Properties of the ternary NaCl-KCl-UCl 3 system that may be used as a fuel bearing salt are being measured. Low-melting eutectic salt compositions are of interest to developers owing to the thermal efficiency. Using salts with low melting temperatures allow reactors to be operated at a lower temperature to improve operation and decrease safety concerns. Confirming low melting behaviors are maintained during composition changes that occur during fission is also an important factor. It is essential to any molten salt reactor developer utilizing a fuel bearing salt to have a complete understanding of the behavior of that fuel salt at a variety of compositions near the eutectic composition they plan to use. This kind of stability is indicated on a phase diagram by low liquidus slopes at compositions bordering the eutectic. Therefore, a thermodynamic model was constructed to determine what compositions of the ternary NaCl, KCl, and UCl 3 system should be studied to support MSR developers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Supercritical Carbon Dioxide Primary Power Large-Scale Pilot Plant

The United States electrical power generation fleet encompasses a wide range of technologies, ranging from traditional combustion-based power generation, to nuclear power, to renewable energy. While the distribution of these assets continues to shift due to economic and regulatory influences, coal combustion continues to be a key part of the US energy portfolio. Despite the relative maturity of coal combustion technology, improvements in overall fuel-to-power efficiency and generation flexibility are still possible and will improve both the economic and environmental factors of coal combustion. Echogen Power Systems proposes to lead a world-class team including the University of Missouri, Electric Power Research Institute and Louis Perry Associates in the design, construction and operation of a 10MWe coal-fired supercritical carbon dioxide (sCO 2 ) large-scale pilot. This transformational technology uses sCO 2 as a working fluid instead of water to achieve high thermodynamic efficiencies that can significantly exceed advanced steam-Rankine cycles. Further, the compact nature of sCO 2 turbomachinery offers capital cost and footprint advantages, and the low maintenance of a water-free power cycle can significantly reduce operation and maintenance (O&M) costs over conventional steam-Rankine systems. Recent integration studies of sCO 2 with coal combustion power plants highlight the significant improvements in plant efficiency that sCO 2 can offer relative to even advanced steam Rankine cycles. At commercial scales, coal-sCO 2 plant net efficiency is predicted to be 39-44.0% (HHV), or 10-20% higher output than conventional steam-Rankine systems, which will significantly improve the competitiveness of coal-fired generation. This proposal builds upon projects previously funded by the Department of Energy, including DE-FE0025959 (High-Efficiency Thermal Integration of Closed Supercritical CO 2 Brayton Power Cycles with Oxy-Fired Heaters) and DE-NE0008470 (Conceptual Design for sCO 2 Power Cycle Test Facility). An appropriately-scaled and properly designed and operated pilot project is essential to overcome the natural risk-aversion of the power generation industry and project financing community. The 10 MWe coal-fired sCO 2 pilot power plant proposed herein will reduce the technical and economic risk of this transformational technology, enabling commercial deployment at the conclusion of the project. For the second phase of this project, Echogen lead a team that completed and refined the pilot system conceptual system and key component designs resulting in the completion of a front-end-engineering-design (FEED) study, completed the NEPA review process, completed the permitting process for construction and operation, refined the techno-economic analysis of the proposed system at commercial scale and received commitments for Phase III cost share. The end result of the program will be to demonstrate the technical and economic superiority of the sCO 2 power cycle for coal-fired operation. Major risk elements will have been retired with sufficient operation at high power to enable the power generation industry to move forward with the first commercial deployment of this transformational system.

01 COAL, LIGNITE, AND PEAT↗

Diesel Combustion for Medium-Duty Off-Road Applications

This project will provide scientific understanding needed to design, optimize, and calibrate the next generations of off-road diesel engines that comply with increasingly stringent pollutant emission regulations while achieving thermal efficiencies exceeding 50%.

33 ADVANCED PROPULSION SYSTEMS↗

NETL Gen-2 Oxygen Carrier Assessment

The National Energy Technology Laboratory’s (NETL) Research and Innovation Center (RIC) has been conducting laboratory-scale tests to develop a new chemical looping combustion (CLC) oxygen carrier (OC) having copper, iron, and alumina components. This OC, designated as the Gen-2 OC throughout this report, has high maximum oxygen capacity and has been tested extensively in the RIC methane-fueled chemical looping reforming. A screening analysis has been conducted to estimate the performance and cost of CLC when utilizing the Gen-2 OC. In this report, the performance and cost results are compared to those of a range of previously assessed CLC OCs to provide a basis to establish the relative merits and issues associated with the Gen-2 OC. Base load CLC power plants utilizing the Gen-2 OC and the three comparison OCs considered in this assessment (Fe 2 O 3- , CuO-, CaSO 4- based) are estimated to have thermal efficiency and cost of electricity (COE) characteristics potentially superior to those of the equivalent conventional pulverized coal (PC) power plant applying conventional, amine-based CO 2 capture technology. The current assessment does not address flexible plant operation. An evaluation of the CLC plant designed for flexible operation would need to include a comparable PC plant designed for flexible operation.

01 COAL, LIGNITE, AND PEAT↗

Technoeconomics of Particle-based CSP Featuring Falling Particle Receivers with and without Active Heliostat Control

This report documents the results and conclusions of a recent project to understand the technoeconomics of utility-scale, particle-based concentrating solar power (CSP) facilities leveraging unique operational strategies. This project included two primary objectives. The first project objective was to build confidence in the modeling approaches applied to falling particle receivers (FPRs) including the effect s of wind. The second project objective was to create the necessary modeling capability to adequately predict and maximize the annual performance of utility-scale, particle-based CSP plants under anticipated conditions with and without active heliostat control. Results of an extensive model validation study provided the strongest evidence to date for the modeling strategies typically applied to FPRs, albeit at smaller receiver scales. This modeling strategy was then applied in a parametric study of candidate utility-scale FPRs, including both free-falling and multistage FPR concepts, to develop reduced order models for predicting the receiver thermal efficiency under anticipated environmental and operating conditions. Multistage FPRs were found to significantly improve receiver performance at utility-scales. These reduced order models were then leveraged in a sophisticated technoeconomic analysis to optimize utility-scale , particle-based CSP plants considering the potential of active heliostat control. In summary, active heliostat control did not show significant performance benefits to future utility-scale CSP systems though some benefit may still be realized in FPR designs with wide acceptance angles and/or with lower concentration ratios. Using the latest FPR technologies available, the levelized-cost of electricity was quantified for particle-based CSP facilities with nominal powers ranging from 5 MW e up to 100 MW e with many viable designs having costs < 0.06 $/kWh and local minimums occurring between ~25–35 MW e .

14 SOLAR ENERGY↗

On-Demand Reactivity Enhancement to Enable Advanced Low Temperature Natural Gas Internal Combustion Engines

This research project set the groundwork for higher technology readiness level implementations of catalytic OCM pretreatment for NG engines. Future work to use OCM as a fuel pretreatment strategy for NG engines should consider catalyst durability and performance over a higher working temp range. Work should also develop robust and practical reactors that can be efficiently thermally integrated with a NG engine.

03 NATURAL GAS↗

FERC Order No. 2222 and Considerations for Distributed Wind

The Federal Energy Regulatory Commission (FERC) issued Order No. 2222 in October 2020. The rule directs Regional Transmission Organizations and Independent System Operators (ISOs) to amend their tariffs and participation models to accommodate heterogeneous distributed energy resource (DER) aggregations in the wholesale energy markets that they operate, including capacity, energy, and ancillary service markets. The Commission issued the rule to better capture the benefits provided by DERs deployed in the United States, whose use has been expanding rapidly. The Commission defines DERs as “any resource located on the distribution system, any subsystem thereof or behind a customer meter,” including but not limited to “electric storage resources, distributed generation, demand response, energy efficiency, thermal storage, and electric vehicles and their supply equipment.” The rule aims to increase DER participation in wholesale markets by allowing the creation of DER aggregations, in which multiple DERs that are too small to meet minimum capacity requirements for wholesale markets individually would be able to participate in markets as a single unit. As of June 20, 2023, all ISOs have filed initial compliance plans and a number have begun implementation. Compliance dates range from 2024 to 2029, with Midcontinent ISO having the latest date of compliance proposed for 2029. Southwest Power Pool still has an outstanding date, having no final order yet from FERC, but a target date of the third quarter of calendar year 2025. The rule, which is technology agnostic and requires ISOs to create participation plans that accommodate different DERs, provides an opportunity for distributed wind market expansion. In addition, distributed wind can bring benefits to heterogenous DER aggregations. These benefits include resource diversity (i.e., a complementary generation profile to other types of distributed generation), its small footprint and ability to be co-located with load, and its potential to provide frequency response, voltage support, and black start services, among other ancillary services. This report provides a status update on FERC Order No. 2222, the current state of ISO compliance, and information relevant to the distributed wind industry as DER aggregators and other stakeholders expand their participation to wholesale energy markets.

17 WIND ENERGY↗

TAILORED BIOBLENDSTOCKS WITH LOW ENVIRONMENTAL IMPACT TO OPTIMIZE MCCI ENGINES

The overall objective of the project is to develop and demonstrate a microalgae bio-blendstock with greater than 60% greenhouse gas reduction potential relative to petroleum diesel, that can reduce sooting propensity, increase cetane number and improve engine thermal efficiency relative to a baseline diesel engine operating on conventional fuel. Specific objectives include: (1) development of a new framework for both LCA and TEA that explicitly considers temporal variation in productivity and the frequency of crop loss; (2) determination of how fuel compounds that can be produced from the algal biomass can be ‘bio-tailored’ based on the species composition and biological production process, and subsequent processing via HTL to biocrude, and upgrading of the biocrude; (3) execution of a feedback loop (algae production  biocrude refining  combustion optimization  feedback to refining stage), for optimization of fuels for MCCI combustion; (4) optimization of MCCI combustion and emissions performance, accounting first for the biological processes that dictate the chemical composition of biocrude oil, and second for the subsequent chemical processes that comprise mixing controlled compression ignition combustion; (6) simulation of MCCI engine combustion processes to demonstrate the incorporation of relevant fuel chemistry that captures the specific impacts of optimized algal fuels.

09 BIOMASS FUELS↗

Tailored Bioblendstocks With Low Environmental Impact To Optimize MCCI Engines

The prohect goal is to develop and demonstrate a microalgae bio-blendstock with greater than 60% greenhouse gas reduction potential relative to petroleum diesel, that can reduce sooting propensity, increase cetane number and improve engine thermal efficiency relative to a baseline diesel engine operating on conventional fuel.

09 BIOMASS FUELS↗

Tailored Bioblendstocks With Low Environmental Impact To Optimize MCCI Engines

This project seeks to overcome impediments to expansion of algae cultivation and conversion into fuels to displace petroleum and reduce greenhouse gas (GHG) emissions. The overall objective of the project is to develop and demonstrate a microalgae bio-blendstock with greater than 60% greenhouse gas reduction relative to petroleum diesel, reduce sooting propensity, increase cetane number, improve engine thermal efficiency relative to a baseline diesel engine operating on conventional fuel. These objectives are being accomplished by: Applying cultivation of algae polycultures to achieve robustness and productivity, Converting whole algae to bio-hydrocarbons via Hydrothermal Liquefaction (HTL) to make a biocrude and up-grading the biocrude via hydroprocessing to obtain tailored bioblendstocks for diesel fuel, Optimizing diesel (MCCI) combustion through blending model compounds into diesel fuel to represent the tailored bioblendstocks through experiments and numerical simulation.

09 BIOMASS FUELS↗

Tailored Bioblendstocks with Low Environmental Impact to Optimize MCCI Engines

The overall objective of the project is to develop and demonstrate a microalgae bio-blendstock with greater than 60% greenhouse gas reduction potential relative to petroleum diesel, that can reduce sooting propensity, increase cetane number and improve engine thermal efficiency relative to a baseline diesel engine operating on conventional fuel. Specific objectives include: (1) development of a new framework for both LCA and TEA that explicitly considers temporal variation in productivity and the frequency of crop loss; (2) determination of how fuel compounds that can be produced from the algal biomass can be ‘bio-tailored’ based on the species composition and biological production process, and subsequent processing via HTL to biocrude, and upgrading of the biocrude; (3) execution of a feedback loop (algae production  biocrude refining  combustion optimization  feedback to refining stage), for optimization of fuels for MCCI combustion; (4) optimization of MCCI combustion and emissions performance, accounting first for the biological processes that dictate the chemical composition of biocrude oil, and second for the subsequent chemical processes that comprise mixing controlled compression ignition combustion; (6) simulation of MCCI engine combustion processes to demonstrate the incorporation of relevant fuel chemistry that captures the specific impacts of optimized algal fuels.

09 BIOMASS FUELS↗