Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “test configuration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Computational Aerodynamic Analysis in Support of the CRM Tail Cone Thruster Configuration Wind Tunnel Test

NASA’s Advanced Air Transport Technology (AATT) project is breaching the boundaries of aircraft design in pursuit of eco-friendly solutions that are compatible with urban noise comfort levels. Boundary layer ingesting (BLI) propulsion systems promise to reduce fuel burn with additional potential benefits in noise reduction. Type-II BLI systems of the STARC-ABL type are the subject of a test campaign planned for fiscal year 2022 in the National Transonic Facility (NTF), for which a CRM-based model with a retrofitted tail cone thruster (TCT) has been designed. The present work is a precursor to the NTF test, where the 240 cases planned for the experiment were simulated using the Launch, Ascent and Vehicle Aerodynamics (LAVA)computational framework. Solution sensitivity to angle of attack, engine operating conditions, and the presence of the supporting structure (sting) in the wind tunnel test are analyzed in the extensive dataset. The main flow features contributing to the inlet distortion are identified as the vertical tail wake, wing downwash and fuselage upsweep vortices, with the latter two experiencing the greatest sensitivity to angle of attack. Finally, results from an inlet-guide-vane(IGV) design/integration study are presented. The LAVA team and the turbomachinery design team at NASA’s Ames and Glenn Research Centers are collaborating in an effort to reduce flow distortion upstream of the fan by means of integrating an IGV system into the CRM-TCT model. A significant improvement in flow distortion metrics has been achieved since the initial design iteration. Results employing an actuator zone model with realistic radially-varying thrust profiles to simulate first-order fan effects within LAVA are presented.

AATT↗
NASA NTRS1946

Flight Measurements of the Directional Stability and Control of a P-51D Airplane with a Horn-Balanced Rudder as Compared with Previously Tested Vertical-Tail Configurations

At the request of the Air Materiel Command, Army Air Forces, flight tests were conducted on a P-5lD-20-NA (AAF No. 44-63826) airplane equipped with a horn-balanced rudder. This rudder was fitted with an unbalancing tab as was the original product fan rudder. Tests were made both with the unbalancing tab in operation and with the unbalancing tab locked. The modification to the original vertical tail consisted of removing the cap from the top of the fin and adding 1.91 square feet of area to the rudder as the horn balance and 0.82 square foot of area to the top of the rudder aft of the hinge line. A comparison of the directional stability and control characteristics of the P-51D airplane with three different vertical-tail configurations - the horn balance, original production, and extended tail (with unbalancing tab locked) configurations are presented herein. The tests of the horn-balanced rudder were conducted at the Langley Laboratory in 1945. The tests of the original-tail configuration were previously conducted at the Ames Aeronautical Laboratory. Tests of the extended-tail configuration were conducted at the Langley Laboratory and are reported.

Mungall, Robert G.↗
NASA NTRS1993

Subsonic static and dynamic stability characteristics of the test technique demonstrator NASP configuration

The paper describes the procedure used for and the results obtained of wind-tunnel tests of the National Aerospace Plane (NASP) configuration, which were conducted in the NASA Langley Research Center High Speed Tunnel using a blended body NASP configuration designed by the research center. Static and dynamic stability characteristics were measured at Mach numbers 0.3, 0.6, and 0.8. In addition to tests of the baseline configuration, component buildup tests with a canard surface and with a body flap were carried out. Results demonstrated a positive static stability of the baseline configuration, except at the higher angles of attack at Mach 0.8. A good agreement was found between the inphase dynamic parameters and the corresponding static data.

Boyden, Richmond P.↗
NASA NTRS1972

Space shuttle: Aerodynamic characteristics of various MDAC space shuttle ascent configurations with parallel burn pressure-fed and SRM boosters. Volume 1: Tanks T1 and T2 ascent configurations

Various space shuttle ascent configurations were tested in a trisonic wind tunnel to determine the aerodynamic characteristics. The ascent configuration consisted of a NASA/MSC 040 orbiter in combination with various HO centerline tank and booster geometries. The aerodynamic interference between components of the space shuttle and the effect on the orbiter aerodynamics was determined. The various aerodynamic configurations tested were: (1) centerline HO tanks T1 and T2, (2) centerline HO tank T3, and (3) centerline HO tank H4.

Jarrett, T. W.↗
NASA NTRS1974

Wind tunnel test of the 0.019 (2A configuration) jet plume space shuttle integrated vehicle in the ARC 9- by 7-foot unitary wind tunnel (IA12B)

The wind tunnel test of the 0.019 jet plume space shuttle integrated vehicle in the Ames 9 ft by 7 ft unitary wind tunnel was conducted at Mach numbers of 1.55 and 2.0 over a Reynolds number range from 3.5 million to 4.1 million/ft. Data were obtained at angles of attack from minus 8 deg to plus 8 deg at 0 deg sideslip and at angles of sideslip from minus 9 deg to plus 8 deg at 0 deg angle of attack. The basic configuration tested was the 2A vehicle with the orbiter at 0 deg angle of incidence with respect to the external tank. The other deviations to the 2A configuration were the solid rocket motor shrouds, which were designed to vehicle '3' lines, and the tank nose, which consisted of the retro-package being removed and replaced by a 16.5 inch full scale radius nose.

Hardin, R. B.↗
NASA NTRS1975

Experimental clean combustor program, phase 1

A program of screening three low emission combustors for conventional takeoff and landing, by testing and analyzing thirty-two configurations is presented. Configurations were tested that met the emission goals at idle operating conditions for carbon monoxide and for unburned hydrocarbons (emission index values of 20 and 4, respectively). Configurations were also tested that met a smoke number goal of 15 at sea-level take-off conditions. None of the configurations met the goal for oxides of nitrogen emissions at sea-level take-off conditions. The best configurations demonstrated oxide of nitrogen emission levels that were approximately 61 percent lower than those produced by the JT9D-7 engine, but these levels were still approximately 24 percent above the goal of an emission index level of 10. Additional combustor performance characteristics, including lean blowout, exit temperature pattern factor and radial profile, pressure loss, altitude stability, and altitude relight characteristics were documented. The results indicate the need for significant improvement in the altitude stability and relight characteristics. In addition to the basic program for current aircraft engine combustors, seventeen combustor configurations were evaluated for advanced supersonic technology applications. The configurations were tested at cruise conditions, and a conceptual design was evolved.

Roberts, R.↗
NASA NTRS2004

Blowing Flap Experiment: PIV Measurements

PIV measurements of the flow in the region of a flap side edge are presented for several flap configurations. The test model is a NACA 63(sub 2)-215 Hicks Mod-B main element airfoil with a half-span Fowler flap. Air is blown from small slots located along the flap side edge on either the top, bottom or side surfaces. The test set up is described and flow measurements for a baseline and three blowing flap configurations are presented. The effects that the flap tip jets have on the structure of the flap side edge flow are discussed for each of the flap configurations tested. The results indicate that blowing air from a slot located along the top surface of the flap greatly weakened the top vortex system and pushed it further off the top surface. Blowing from the bottom flap surface kept the strong side vortex further outboard while blowing from the side surface only strengthened the flap vortex system. It is concluded that blowing from the top or bottom surfaces of the flap may lead to a reduction of flap side edge noise.

Hutcheson, Florence V.↗
NASA NTRS2004

PIV Measurements on a Blowing Flap

PIV measurements of the flow in the region of a flap side edge are presented for several blowing flap configurations. The test model is a NACA 63(sub 2)-215 Hicks Mod-B main-element airfoil with a half-span Fowler flap. Air is blown from small slots located along the flap side edge on either the top, bottom or side surfaces. The test set up is described and flow measurements for a baseline and three blowing flap configurations are presented. The effects that the flap tip jets have on the structure of the flap side edge flow are discussed for each of the flap configurations tested. The results indicate that blowing air from a slot located along the top surface of the flap greatly weakened the top vortex system and pushed it further off the top surface. Blowing from the bottom flap surface kept the strong side vortex further outboard while blowing from the side surface only strengthened the vortex system or accelerated the merging of the side vortex to the flap top surface. It is concluded that blowing from the top or bottom surfaces of the flap may lead to a reduction of flap side edge noise.

Hutcheson, Florence V.↗
NASA NTRS2018

Use of the Ames Check Standard Model for the Validation of Wall Interference Corrections

The new check standard model of the NASA Ames 11-ft Transonic Wind Tunnel was chosen for a future validation of the facility's wall interference correction system. The chosen validation approach takes advantage of the fact that test conditions experienced by a large model in the slotted part of the tunnel's test section will change significantly if a subset of the slots is temporarily sealed. Therefore, the model's aerodynamic coefficients have to be recorded, corrected, and compared for two different test section configurations in order to perform the validation. Test section configurations with highly accurate Mach number and dynamic pressure calibrations were selected for the validation. First, the model is tested with all test section slots in open configuration while keeping the model's center of rotation on the tunnel centerline. In the next step, slots on the test section floor are sealed and the model is moved to a new center of rotation that is 33 inches below the tunnel centerline. Then, the original angle of attack sweeps are repeated. Afterwards, wall interference corrections are applied to both test data sets and response surface models of the resulting aerodynamic coefficients in interference-free flow are generated. Finally, the response surface models are used to predict the aerodynamic coefficients for a family of angles of attack while keeping dynamic pressure, Mach number, and Reynolds number constant. The validation is considered successful if the corrected aerodynamic coefficients obtained from the related response surface model pair show good agreement. Residual differences between the corrected coefficient sets will be analyzed as well because they are an indicator of the overall accuracy of the facility's wall interference correction process.

wind tunnel wall interferenc↗
NASA NTRS1951

Stability and Control Characteristics of a Complete Airplane Model Having a Wing with Quarter-chord Line Swept Back 40 Degrees, Aspect Ratio 2.50, and Taper Ratio 0.42

An investigation has been made of a complete airplane model having a wing with the quarter-chord line swept back 40 degrees, aspect ratio 2.50, and taper ratio 0.42 to determine its low-speed stability and control characteristics. The longitudinal stability investigation included stabilizer and tail-off tests with different wing dihedral angles (Gamma = 0 degrees and Gamma = -10 degrees) over an angle-of-attack range for the cruising and landing configurations and tests. with a high horizontal-tail location (Gamma = -10 degrees) for the cruising configuration. Tests were made of the wing alone and to determine the effect of wing end plates in pitch. Lateral stability characteristics were determined for the airplane with different geometric wing dihedrals, with end plates, and with several dorsal modifications. Tests were made with ailerons and spoilers to determine control characteristics.

STABILITY, STATIC↗
NASA NTRS2015

Experimental Study of Fillets to Reduce Corner Effects in an Oblique Shock-Wave/Boundary Layer Interaction

A test was conducted in the 15 cm x 15 cm supersonic wind tunnel at NASA Glenn Research Center that focused on corner effects of an oblique shock-wave/boundary-layer interaction. In an attempt to control the interaction in the corner region, eight corner fillet configurations were tested. Three parameters were considered for the fillet configurations: the radius, the fillet length, and the taper length from the square corner to the fillet radius. Fillets effectively reduced the boundary-layer thickness in the corner; however, there was an associated penalty in the form of increased boundary-layer thickness at the tunnel centerline. Larger fillet radii caused greater reductions in boundary-layer thickness along the corner bisector. To a lesser, but measureable, extent, shorter fillet lengths resulted in thinner corner boundary layers. Overall, of the configurations tested, the largest radius resulted in the best combination of control in the corner, evidenced by a reduction in boundary-layer thickness, coupled with minimal impacts at the tunnel centerline.

Fillets↗
NASA NTRS1988

High-alpha flight dynamics research on the X-29 configuration using dynamic model test techniques

High-angle-of-attack flight dynamics of the X-29 configuration were studied using dynamic model test techniques. These tests identified phenomena including wing rock, spins, and tumbling which dominate the high-alpha behavior of the configuration and define its usable flight envelope. Results of these tests have been used to design flight control concepts to minimize adverse behavior. Planned high-angle-of-attack flight tests of the X-29 airplane will provide an opportunity to validate the model predictions.

Croom, Mark A.↗
NASA NTRS2020

USM3D Analyses in Support of the NASA Langley 0.3-Meter Transonic Cryogenic Tunnel Test of Boundary-Layer Thickener Configurations

A wind tunnel test was performed in the 0.3-Meter Cryogenic Transonic Tunnel at the NASA Langley Research Center to investigate the impact of various boundary layer thickeners on the height and shape of the boundary layer on the aft portion of a semispan fuselage. The present work discusses USM3D analyses that were performed in support of the wind tunnel test. The results consisted of comparisons between USM3D and experimental data for the baseline configuration and two boundary layer thickening configurations. The comparisons considered surface pressure distributions, boundary layer profiles, and calculated boundary layer thicknesses. Additionally, a grid refinement study was performed for each of the three configurations, which illustrated general improvement in the comparisons with increasing grid refinement. Overall, the comparisons show favorable agreement between the USM3D predictions and the experimental data.

Bozeman, Michael D., Jr.↗
NASA NTRS2022

Framework for Estimating Performance and Associated Uncertainty for Modified Aircraft Configurations

Flight testing has been the historical standard for determining aircraft airworthiness - however, increases in the cost of flight testing and the accuracy of inexpensive CFD promote certification by analysis to reduce or replace flight testing. A framework is introduced to predict the performance in the special case of a modification to an existing, previously certified aircraft. This framework uses a combination of existing flight test or high fidelity data of the original aircraft as well as lower fidelity data of the original and modified configurations. Two methods are presented which estimate the model form uncertainty of the modified configuration, which is then used to conduct non-deterministic simulations. The framework is applied to an example aircraft system with simulated flight test data to demonstrate the ability to predict the performance and associated uncertainty of modified aircraft configurations. However, it is important that the models and methods used are applicable and accurate throughout the intended use domain. The factors and limitations of the framework are explored to determine the range of applicability of the framework. The effects of these factors on the performance and uncertainty results are demonstrated using the example aircraft system. The framework is then applied to NASA’s X-57 Maxwell and each of its modifications. The estimated performance and associated uncertainties are then compared to the airworthiness criteria to evaluate the potential of the framework as a component to the certification by analysis process.

Uncertainty Quantification↗