SEARCH · Engineering Papers

Results for “surface operations analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS2000

Characterization of Advanced Avalanche Photodiodes for Water Vapor Lidar Receivers

Development of advanced differential absorption lidar (DIAL) receivers is very important to increase the accuracy of atmospheric water vapor measurements. A major component of such receivers is the optical detector. In the near-infrared wavelength range avalanche photodiodes (APD's) are the best choice for higher signal-to-noise ratio, where there are many water vapor absorption lines. In this study, characterization experiments were performed to evaluate a group of silicon-based APD's. The APD's have different structures representative of different manufacturers. The experiments include setups to calibrate these devices, as well as characterization of the effects of voltage bias and temperature on the responsivity, surface scans, noise measurements, and frequency response measurements. For each experiment, the setup, procedure, data analysis, and results are given and discussed. This research was done to choose a suitable APD detector for the development of an advanced atmospheric water vapor differential absorption lidar detection system operating either at 720, 820, or 940 nm. The results point out the benefits of using the super low ionization ratio (SLIK) structure APD for its lower noise-equivalent power, which was found to be on the order of 2 to 4 fW/Hz(sup (1/2)), with an appropriate optical system and electronics. The water vapor detection systems signal-to-noise ratio will increase by a factor of 10.

Refaat, Tamer F.↗

NASA NTRS2005

Variable Structure Control of a Hand-Launched Glider

Variable structure control system design methods are applied to the problem of aircraft spin recovery. A variable structure control law typically has two phases of operation. The reaching mode phase uses a nonlinear relay control strategy to drive the system trajectory to a pre-defined switching surface within the motion state space. The sliding mode phase involves motion along the surface as the system moves toward an equilibrium or critical point. Analysis results presented in this paper reveal that the conventional method for spin recovery can be interpreted as a variable structure controller with a switching surface defined at zero yaw rate. Application of Lyapunov stability methods show that deflecting the ailerons in the direction of the spin helps to insure that this switching surface is stable. Flight test results, obtained using an instrumented hand-launched glider, are used to verify stability of the reaching mode dynamics.

Anderson, Mark R.↗

NASA NTRS2004

Mars Exploration Rovers orbit determination filter strategy

The successful delivery of the Mars Exploration Rover (MER) landers to well with in the boundaries of their surface target areas in January of 2004 was the culmination of years of orbit determination analysis. The process began with a careful consideration of the filter parameters used for pre-launch covariance studies, and continued with the refinement of the filter after launch based on operational experience. At the same time, tools were developed to run a plethora of variations around the nominal filter and anlyze the results in ways that had never been previously attempted for an interplanetary mission. In addition to the achieved sub-kilometer Mars B plane orbit determination knowledge, the filter strategy and process responded to unexpected error sources by both detecting them and proving robust. All these facets of the MER orbit determination filter strategy are described in this paper.

orbit determination↗

NASA NTRS2004

Mars Exploration Rovers orbit determination filter strategy

The successful delivery of the Mars Exploration Rover (MER) landers to well within the boundaries of their surface target areas in January of 2004 was the culmination of years of orbit determination analysis. The process began with a careful consideration of the filter parameters used for pre-launch covariance studies, and continued with the refinement of the filter after launch based on operational experience. At the same time, tools were developed to run a plethora of variations around the nominal filter and analyze the results in ways that had never been previously attempted for an interplanetary mission. In addition to achieving sub-kilometer Mars-relative orbit determination knowledge, the filter strategy and process detected unexpected error sources, while at the same time proving robust by indicating thecorrect solution. Consequently, MER orbit determination set a new standard for interplanetary navigation.

Mars Exploration Rover (MER)↗

NASA NTRS2007

Gravity Scaling of a Power Reactor Water Shield

A similarity analysis on a water-based reactor shield examined the effect of gravity on free convection between a reactor shield inner and outer vessel boundaries. Two approaches established similarity between operation on the Earth and the Moon: 1) direct scaling of Rayleigh number equating gravity-surface heat flux products, 2) temperature difference between the wall and thermal boundary layer held constant. Nusselt number for natural convection (laminar and turbulent) is assumed of form Nu = CRa(sup n).

Reid, Robert S.↗

NASA NTRS2007

Cost-Benefit Analysis For Alternative Low-Emission Surface Preparation/ Depainting Technologies for Structural Steel

Stennis Space Center (SSC), Kennedy Space Center (KSC) and Air Force Space Command (AFSPC) identified particulate emissions and waste generated from the depainting process of steel structures as hazardous materials to be eliminated or reduced. A Potential Alternatives Report, Potential Alternatives Report for Validation of Alternative Low Emission Surface Preparation/Depainting Technologies for Structural Steel, provided a technical analyses of identified alternatives to the current coating removal processes, criteria used to select alternatives for further analysis, and a list of those alternatives recommended for testing. The initial coating removal alternatives list was compiled using literature searches and stakeholder recommendations. The involved project participants initially considered approximately 13 alternatives. In late 2003, core project members selected the following depainting processes to be further evaluated: (1) Plastic Blast Media-Quickstrip(R)-A. (2) Hard Abrasive-Steel-Magic(R). (3) Sponge Blasting-Sponge-Jet(R). (4) Liquid Nitrogen-NItroJet(R). (5) Mechanical Removal with Vacuum Attachment-DESCO and OCM Clean-Air (6) Laser Coating Removal Alternatives were tested in accordance with the Joint Test Protocol for Validation of Alternative Low-Emission Surface Preparation/Depainting Technologies for Structural Steel, and the Field Evaluation Test Plan for Validation of Alternative Low-Emission Surface Preparation/Depainting Technologies for Structural Steel. Results of the testing are documented in the Joint Test Report. This Cost-Benefit Analysis (CBA) focuses on the three alternatives (Quickstrip(R)-A, SteelMagic (R), and Sponge-Jet(R)) that were considered viable alternatives for large area operations based on the results of the field demonstration and lab testing. This CBA was created to help participants determine if implementation of the candidate alternatives is economically justified. Each of the alternatives examined reduced Environmental Activity (EA) Costs-those costs associated with complying with environmental regulations. One alternative, Steel-Magic(R), also showed reduced Direct Costs and reduced total costs.

Lewis, Pattie↗

NASA NTRS2015

Assimilation of GRACE Terrestrial Water Storage Observations into a Land Surface Model for the Assessment of Regional Flood Potential

We evaluate performance of the Catchment Land Surface Model (CLSM) under flood conditions after the assimilation of observations of the terrestrial water storage anomaly (TWSA) from NASA's Gravity Recovery and Climate Experiment (GRACE). Assimilation offers three key benefits for the viability of GRACE observations to operational applications: (1) near-real time analysis; (2) a downscaling of GRACE's coarse spatial resolution; and (3) state disaggregation of the vertically-integrated TWSA. We select the 2011 flood event in the Missouri river basin as a case study, and find that assimilation generally made the model wetter in the months preceding flood. We compare model outputs with observations from 14 USGS groundwater wells to assess improvements after assimilation. Finally, we examine disaggregated water storage information to improve the mechanistic understanding of event generation. Validation establishes that assimilation improved the model skill substantially, increasing regional groundwater anomaly correlation from 0.58 to 0.86. For the 2011 flood event in the Missouri river basin, results show that groundwater and snow water equivalent were contributors to pre-event flood potential, providing spatially-distributed early warning information.

flood↗

NASA NTRS2014

Geology Before Pluto: Pre-Encounter Considerations

The cameras of New Horizons will provide robust data sets that should be imminently amenable to geological analysis of the Pluto systems landscapes. In this paper, we begin with a brief discussion of the planned observations by the New Horizons cameras that will bear most directly on geological interpretability. Then we broadly review the major geological processes that could potentially operate on the surfaces of Pluto and its major moon Charon. We first survey exogenic processes (i.e. those for which energy for surface modification is supplied externally to the planetary surface): impact cratering, sedimentary processes (including volatile migration), and the work of wind. We conclude with an assessment of the prospects for endogenic activity in the form of tectonics and cryovolcanism.

Pluto↗

NASA NTRS1983

Bearing tester data compilation, analysis, and reporting and bearing math modeling

The Shaberth bearing analysis computer program was developed for the analysis of jet engine shaft/bearing systems operating above room temperature with normal hydrocarbon lubricants. It is also possible to use this tool to evaluate the shaft bearing systems operating in cryogenics. Effects such as fluid drag, radial temperature gradients, outer race misalignments and clearance changes were simulated and evaluated. In addition, the speed and preload effects on bearing radial stiffness was evaluated. The Shaberth program was also used to provide contact stresses from which contact geometry was calculated to support other analyses such as the determination of cryogenic fluid film thickness in the contacts and evaluation of surface and subsurface stresses necessary for bearing failure evaluation. This program was a vital tool for the thermal analysis of the bearing in that it provides the heat generation rates at the rolling element/race contacts for input into a thermal model of the bearing/shaft assembly.

Source record↗

NASA NTRS2016

Retrieval of Ice Cloud Properties Using an Optimal Estimation Algorithm and MODIS Infrared Observations: 2. Retrieval Evaluation

An infrared-based optimal estimation (OE-IR) algorithm for retrieving ice cloud properties is evaluated. Specifically, the implementation of the algorithm with MODerate resolution Imaging Spectroradiometer (MODIS) observations is assessed in comparison with the operational retrieval products from MODIS on the Aqua satellite (MYD06), Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP), and the Imaging Infrared Radiometer (IIR); the latter two instruments fly on the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) satellite in the Afternoon Constellation (A-Train) with Aqua. The results show that OE-IR cloud optical thickness (tau) and effective radius (r(sub eff)) retrievals perform best for ice clouds having 0.5 < tau< 7 and r(sub eff) < 50microns. For global ice clouds, the averaged retrieval uncertainties of tau and r(sub eff) are 19% and 33%, respectively. For optically thick ice clouds with tau larger than 10, however, the tau and r(sub eff) retrieval uncertainties can exceed 30% and 50%, respectively. For ice cloud top height (h), the averaged global uncertainty is 0.48km. Relatively large h uncertainty (e.g., > 1km) occurs for tau < 0.5. Analysis of 1month of the OE-IR retrievals shows large tau and r(sub eff) uncertainties in storm track regions and the southern oceans where convective clouds are frequently observed, as well as in high-latitude regions where temperature differences between the surface and cloud top are more ambiguous. Generally, comparisons between the OE-IR and the operational products show consistent tau and h retrievals. However, obvious differences between the OE-IR and the MODIS Collection 6 r(sub eff) are found.

cloud optics↗

NASA NTRSDate not supplied

Fluid System Stability Analysis Techniques

Fluid systems, or networks, consist of multiple components that work together to achieve some desired thermofluid state. For any generic application, this fluid state can be a combination of the fluid pressure, flow rate, enthalpy, or species concentration. Fluid system components, such as pumps and valves, are often governed by nonlinear differential equations, resulting in complex component-to-component interactions. System-level fluid network stability occurs when the flow through the system can maintain a steady-state solution in the presence of small perturbations, which depends on these component interactions. System instability, however, can go undetected until issues arise during integrated system testing. This presentation explores a method for system designers to think of the fluid network as an assembly of components, each with their own thermofluid surfaces of partial stability, called nullclines. The intersections of all nullclines yields system-level solutions, called equilibrium points. When designers define operating points, they are tuning system parameters so that these equilibrium points move to the desired location in the thermofluid state plane. However, linearization theory shows us that the dynamic behavior around these points can be unstable. The local stability of these equilibrium points can be assessed analytically with eigen-analysis, or numerically by propagating state-plane samples to construct a phase portrait. Investigating a phase portrait can help designers gain a qualitative understanding of a system’s dynamic performance. This understanding can then help inform requirement definitions, component selection, and operational procedures. This presentation includes an example of the phase portrait technique on a system featuring a centrifugal pump and a back-pressure regulator (BPR). Numerical modeling of this system suggests that equilibrium points on the left-hand side of the pump curve are dynamically unstable.

Fluid System↗

NASA NTRSDate not supplied

Fluid System Stability Analysis Techniques

Fluid System↗

DOE OSTI2022

Characterizing particle-based thermal storage performance using optical methods for use in next generation concentrating solar power plants

Concentrating Solar Power (CSP) generation is an attractive option for low-emission power generation; however, the high costs of thermal storage associated with concentrating solar create a large barrier for their use and adaptation into modern life. Lowering their operation costs, while maintaining high thermal storage and transfer performance is essential. Solid particle-based heat exchange systems can reduce CSP cost but are often less efficient. Efforts to increase their performance have led to use of binary size particle mixes. Presented is an optical-based thermal analysis technique used to measure near-wall thermal conductivity of particle beds essential in determining their heat exchanger efficiency. Modulated Photothermal Radiometry is used to make dynamic temperature measurements, allowing for the extraction of the most relevant thermal properties like thermal conductivity, specific heat, and effusivity. The system uses a modulated laser source causing a damped periodic heat flux, resulting in a frequency and thermal property dependent surface temperature, of which is measured using radiometry. Lock-In techniques are used to extrapolate the amplitude of the signal. Plotting the amplitude against the root angular frequency allows for effusivity measurement by ratio to a known sample. Using specific heat measurements from literature and density measurements, the thermal conductivity of the particle mixes can be calculated. The simplicity of MPTR to probe through the depth of the bed is ideal for use in CSP for dynamic thermal performance monitoring.

Corona, Javier↗

NASA NTRSDate not supplied

A Comparative Assessment of Evolvable Martian ISRU Propellant Production for Future Human Missions

In 2022, NASA released its “Moon to Mars Strategy and Objectives Development” document, containing top-level goals and objectives designed to create a blueprint for sustained human presence and exploration throughout the solar system. One objective in this “blueprint” calls for the demonstration of “…Mars ISRU capabilities to support an initial human Mars exploration campaign.” NASA is looking at both the benefits and liens of this concept, as one of several trade space aspects under consideration, for inclusion in the overall architecture of the human exploration of Mars. This paper summarizes results from a series of Martian ISRU-focused trade studies from 2023 and 2024. These studies cover five different approaches to providing propellants for returning crew and equipment from the surface of Mars, using several different combinations of propellants delivered (from Earth) and produced from Martian feedstock material. For comparison purposes, the same ISRU infrastructure elements were used across all options wherever possible. The equipment mass, power, operational complexity, and time needed to produce some or all of these propellants have been quantified and compared when used in a common mission scenario. Analysis results for each option are discussed. Performance parameters for these options are compared side-by-side and observations made, including the positive and negative aspects of each case. The possibility of evolving from a simpler ISRU case to more complex cases that would potentially lead to more sustainable operations are also discussed. While no single case emerged as “better” in all aspects when compared to the others, there are distinct advantages and disadvantages that did emerge when comparing the results generated from a common set of assumptions for all cases. Consequently, specific mission objectives may determine which of these advantages or disadvantages are important for choosing among the cases that could benefit any particular mission or campaign.

Mars↗

NASA NTRS1981

Analysis of data from a wind tunnel investigation of a large-scale model of a highly maneuverable supersonic V/STOL fighter - STOL configuration

The surface pressure and thermal characteristics of a large-scale model of a highly maneuverable supersonic fighter with STOL capability are described. The 7.28 m span model is powered by two J-97 turbojets, operated at 9340 N thrust. It combines upper-surface and spanwise blowing to augment the lift characteristics over a wide angle-of-attack range. The most significant feature of the fighter's flow field is the leading edge vortex that forms at low alphas, grows stronger, and moves inboard as alpha is increased. Upper surface blowing enhanced the lift on the wing in both stalled and unstalled areas significantly, while generating only a modest aft shift in the center of pressure. Lift gains were greatest at high alphas and with the flap deflected. Spanwise blowing was most significant at angles-of-attack greater than 8 deg, when the jet strengthened the vortex. The 1100 F spanwise blowing jet mixed very rapidly with the wing flow field, creating a maximum temperature rise of only 300-350 F. A comparison of small-scale and large-scale model wing pressure characteristics showed similar trends created by upper surface blowing, while spanwise blowing characteristics differed considerably. Force data correlated well with semi-empirical predictions for gross thrust coefficients less than 1.0.

Falarski, M. D.↗

NASA NTRS1983

An analysis of propulsion options for transport of lunar materials to earth orbit

This paper describes the results of analyses of space-based transportation systems for the transport of extraterrestrial materials from their point of origin on the lunar surface to final delivery point in earth orbit and transport of equipment and supplies for extraterrestrial processing to the operational site. The emphasis has been on the use of near-term (pre-year 2000) propulsion systems, such as advanced chemical (H2, O2) and nuclear-electric systems. More exotic systems (mass drivers, nuclear-thermal rockets, etc.) were also considered to evaluate the potential to be gained by use of post-year 2000 technologies. Finally, the effects of using extraterrestrial propellants (e.g., H2 from lunar polar water-ice for chemical systems) were compared to those of propulsion systems deriving all or part of their propellants from the earth.

Frisbee, R. H.↗

NASA NTRS1985

Innovative research in the design and operation of large telescopes for space: Aspects of giant telescopes in space

The capability and understanding of how to finish the reflector surfaces needed for large space telescopes is discussed. The technology for making very light glass substrates for mirrors is described. Other areas of development are in wide field imaging design for very fast primaries, in data analysis and retrieval methods for astronomical images, and in methods for making large area closely packed mosaics of solid state array detectors.

Angel, J. R. P.↗

NASA NTRS1992

Analysis of crustal structure of Venus utilizing residual Line-of-Sight (LOS) gravity acceleration and surface topography data. A trial of global modeling of Venus gravity field using harmonic spline method

To construct Venus' gravity disturbance field (or gravity anomaly) with the spacecraft-observer line of site (LOS) acceleration perturbation data, both a global and a local approach can be used. The global approach, e.g., spherical harmonic coefficients, and the local approach, e.g., the integral operator method, based on geodetic techniques are generally not the same, so that they must be used separately for mapping long wavelength features and short wavelength features. Harmonic spline, as an interpolation and extrapolation technique, is intrinsically flexible to both global and local mapping of a potential field. Theoretically, it preserves the information of the potential field up to the bound by sampling theorem regardless of whether it is global or local mapping, and is never bothered with truncation errors. The improvement of harmonic spline methodology for global mapping is reported. New basis functions, a singular value decomposition (SVD) based modification to Parker & Shure's numerical procedure, and preliminary results are presented.

Fang, Ming↗