Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “selective adsorption”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Metabolic Heat Regenerated Temperature Swing Adsorption for CO(sub 2) and Heat Removal/Rejection in a Martian PLSS

Two of the fundamental problems facing the development of a Portable Life Support System (PLSS) for use on Mars, are (i) heat rejection (because traditional technologies use sublimation of water, which wastes a scarce resource and contaminates the premises), and (ii) rejection of CO2 in an environment with a ppCO2 of 0.4-0.9 kPa. Patent-pending Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed to address both these challenges. The technology utilizes an adsorbent that when cooled with liquid CO2 to near sublimation temperatures (~195K) removes metabolically-produced CO2 in the vent loop. Once fully loaded, the adsorbent is then warmed externally by the vent loop (approx. 300K), rejecting the captured CO2 to Mars ambient. Two beds are used to effect a continuous cycle of CO2 removal/rejection as well as facilitate heat exchange out of the vent loop. Any cryogenic fluid can be used in the application; however, since CO2 is readily available at Mars and can be easily produced and stored on the Martian surface, the solution is rather elegant and less complicated when employing liquid CO2. As some metabolic heat will need to be rejected anyway, finding a practical use for metabolic heat is also an overall benefit to the PLSS. To investigate the feasibility of the technology, a series of experiments was conducted which lead to the selection and partial characterization of an appropriate adsorbent. The adsorbent NaX successfully removed CO2 from a simulated vent loop at the prescribed temperature swing anticipated during PLSS operating conditions on Mars using a cryogenic fluid. Thermal conductivity of the adsorbent was also measured to eventually aid in a demonstrator design of the technology. These results provide no show stoppers to the development of MTSA technology and allow its development to focus on other design challenges as listed in the conclusions.

Iacomini, Christine↗
DOE OSTI2026

Trends and limits of CO 2 capture in solid and liquid sorbents at standard conditions

Carbon capture and storage (CCS) plays a critical role in achieving climate change mitigation targets, offering a pathway to decarbonize power generation, industrial processes, and heat production while addressing atmospheric CO 2 removal. While CCS technologies are technically advanced, the widespread adoption of 100 % CO 2 capture capacities such as 1 mol of CO 2 /mol of material and 1 g CO 2 /g storage (targeted by the DARPA, Defense Sciences Office, USA Govt.) has raised questions about the feasibility of achieving higher capture capacities. In the context of limiting global warming to 1.5°C, reaching 100 % CO 2 capture capacity is increasingly necessary, with residual emissions requiring complementary carbon dioxide removal (CDR) technologies. This review exclusively focuses on the CO 2 capture capacities of various sorbents under standard conditions, using different evaluation metrics. This study explores the performance of solid and liquid sorbents under standard conditions, analyzing factors including surface area, pore structure, solvent type, and functionalization to identify materials optimized for industrial-scale CCS applications. Emerging sorbents, including ILs, MOFs, COFs, POPs, DES, RCC, hybrid materials, and reactive sorbents, offer significant potential for enhanced selectivity and energy-efficient regeneration. Through a systematic assessment of gravimetric, volumetric, and molar capacities, the study provides insights into material efficiencies and trade-offs, offering guidance on optimizing sorbent selection for specific applications. The research advances understanding of scalable CCS technologies, contributing to global efforts to achieve net-zero emissions and address the pressing challenge of climate change.

Absorption↗
DOE OSTI2025

A Combined Water and CO 2 Direct Air Capture System (Final Technical Report)

The primary objective of the project was to demonstrate the technical and economic performance of a technology that simultaneously captures CO 2 and water from the air – a Hybrid Direct Air Capture system (HDAC). In HDAC, air is passed over water capture section as well as a CO 2 selective sorbent to remove CO 2 from the air stream. Combining potable water generation and CO 2 capture in a single device with the unique energy conserving features of the proposed design enables long-term projected CAPEX under $\$$750/t-CO 2 and levelized cost of capture (LCOC) of $\$$140/t-CO 2 . Project DE-FE-0031970 "A Combined Water and CO 2 Direct Air Capture System" ran for four years and three months from 10/01/2020 to 12/31/2024 for three budget periods and an extension period. The total project budget at completion was $\$$3,534,408 consisting of a $\$$2,680,064 federal share and $\$$854,344 cost share. The pilot plant was successfully designed, engineered, built and commissioned during the initial three budget periods. The plant demonstrated successful water capture during this period, whereas initial CO 2 capture was well below target values. The project team requested an extension period during which alternate materials and beds were evaluated. By the end of the project, both moisture swing adsorption of CO 2 and water capture had successfully been demonstrated at target capture rates making further scale-up of the technology viable.

42 ENGINEERING↗
DOE OSTI2020

Ethanol Conversion over La 0.7 Sr 0.3 MnO 3–x (100): Autocatalysis, Adjacent O-Vacancies, Disproportionation, and Dehydrogenation

The mechanism for catalytic conversion of ethanol over La 0.7 Sr 0.3 MnO 3– x (100) surface to acetaldehyde and ethene was investigated. Pre-exposure temperature-programmed reaction (PE-TPR) experiments were performed in which ethanol was introduced to oxidized or reduced surfaces followed by heating. In particular, sequential PE-TPR experiments were conducted to incrementally and gradually reduce the surface. The products and their ratios were investigated as a function of surface reduction. The data show that acetaldehyde and ethene production is catalyzed with hydrogen abstraction and oxygen abstraction reactions occurring by intermediates in vacancies at various temperatures >400 K. Adsorption of acetaldehyde followed by a temperature-programmed reaction does not produce ethene, indicating that acetaldehyde is not an intermediate to ethene and that the hydrogen and oxygen abstraction from ethanol to ethene are decoupled steps. Further evidence for this mechanistic nuance was obtained using isotopically labeled ethanol (CD 3 CH 2 OH), which produces CD 3 CHO and CD 2 CH 2 . Additionally, the ratio of aldehyde production to alkene production increases with reduction, suggesting that aldehyde is produced from a disproportionation reaction between ethoxy species in adjacent O-vacancies, while ethene is produced from a dehydrogenation reaction with ethoxy species in vacancies without requiring adjacent O-vacancies. Counterintuitively, this finding indicates that the more oxygenated product (aldehyde vs ethene) is favored with more vacancies and that the net alcohol conversion is autocatalytic. Density functional theory calculations were able to find the previously unknown disproportionation pathway between ethoxies in adjacent O-vacancies, and kinetic Monte Carlo simulations support this interpretation by reproducing experimental selectivities. The activation energies for these pathways are estimated as 132 ± 10 kJ/mol for the disproportionation reaction (when occurring between ethoxies in adjacent vacancies) and as 148 ± 11 kJ/mol for the direct dehydrogenation reaction of an ethoxy in a vacancy. Based on these results, a mechanism with operative pathways based on elementary steps in O-vacancies is reported.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Metal–Organic Frameworks for C6 Alkane Separation

The separation of alkane isomers is an important yet challenging process in the petrochemical industry. Being a crucial step to produce premium gasoline components as well as optimum ethylene feed, the current industrial separation by distillation is extremely energy intensive. Adsorptive separation based on zeolite is limited by insufficient adsorption capacity. Metal-organic frameworks (MOFs) hold enormous promise as alternative adsorbents due to their diverse structural tunability and exceptional porosity. Precise control of their pore geometry/dimensions has led to superior performance. In this minireview, we highlight the recent progresses in developing MOFs for the separation of C6 alkane isomers. Representative MOFs are reviewed based on their separation mechanisms. Emphasis is put on the material design rationale for achieving optimal separation capability. Lastly, we briefly discuss the existing challenges, possible solutions, and future directions of this important field.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2019

Monolithic Trace-Contaminant Sorbents Fabricated from 3D-Printed Polymer Precursors

The current trace-contaminant (TC) removal technology for use in Extravehicular Activities (EVAs) involves the use of a packed bed of acid-impregnated granular charcoal, which is difficult to regenerate. In this paper, results are presented on the development of vacuum-regenerable TC sorbents for use in the Portable Life Support System (PLSS). The sorbents are derived from 3D-printed polymer monoliths (e.g., honeycomb structures), which are then carbonized and activated in order to develop porosity, and also to enhance the TC-sorption capacity. Results are presented on the following aspects of carbon-sorbent development: (1) precursor selection; (2) monolith fabrication; (3) shape retention and strength; (4) carbon surface and porosity characterization; (5) TC-sorption capacity and vacuum-regeneration; (6) pressure drop; and (7) sub-scale sorbent prototype. The use of predominantly microporous monolithic carbon is associated with the following benefits: (a) high TC-sorption capacity; (b) low pressure drop; (c) rapid vacuum (pressure-swing) desorption due to thin monolith walls and low pressure drop; (d) good thermal management (high thermal conductivity and low adsorption/desorption thermal effects associated with physisorption); and (e) good resistance to dusty environments.

Portable Life Support System (PLSS)↗
DOE OSTI2025

Unveiling the support effect in Pt-based catalysts for the selective catalytic oxidation of NH 3 under realistic diesel engine conditions

Pt catalysts have been widely used for the selective catalytic oxidation of NH 3 (NH 3 -SCO) in practical applications due to their high activity at low temperatures. However, more stringent regulations require further enhancement of low-temperature NH 3 -SCO activity. In this study, we investigated the influence of different supports, including aluminum oxide (Al 2 O 3 ), silica (SiO 2 ), and chabazite (CHA), on the NH 3 -SCO performance of Pt catalysts. Furthermore, our findings demonstrate that the Pt/CHA catalyst exhibited superior NH 3 -SCO performance under realistic diesel engine conditions, characterized by high space velocity and the presence of water vapor. Notably, the Pt/CHA catalyst achieved a significantly lower T 50 (temperature at which 50% NH 3 conversion is achieved) of 218 °C under conditions with both CO 2 and H 2 O, with a 56 °C reduction compared to the state-of-the-art Pt/Al 2 O 3 catalyst. The exceptional NH 3 -SCO performance is attributed to the high abundance of metallic Pt 0 species and the presence of rich and stable acid sites that facilitate NH 3 adsorption and activation. Furthermore, these results highlight CHA as a promising support for the Pt catalyst in NH 3 -SCO applications for diesel engine emission control.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Topological Bismuth (1 1̅ 0) Facet for Efficient Oxygen Reduction Cathode in Fuel Cells

The performance of proton-exchange membrane fuel cells is strongly dependent on the efficiency of the electrochemical oxygen reduction reaction (ORR). Here, we report both two-dimensional (4 monolayer, ML) and three-dimensional Bi (16 ML) (11̅0) facets deliver a strong correlation between nontrivial topological surface states and low electrochemical overpotential toward ORR. Both topological Bi (11̅0) film and slab have two slightly gapped (9–45 meV) Dirac cones with the invariant Z 2 =1, derived from the parity products for the occupied states at four time-reversal invariant momentum points. By contrast, the Bi (110) film is stabilized as an ordinary insulator due to atomic buckling. The much lower thermodynamic ORR overpotential (η = 0.58 V) and higher H 2 O selectivity by four steps of H + /e – transfer are obtained on the topological Bi (11̅0) surface compared with the nontopological (110) facet (η = 0.84 V). This promotional effect can be attributed to the accumulation of topological surface bands (Bi 6p orbitals) near the Fermi energy, which provide stronger electronic transport channels along the surface Bi–Bi and Bi–O bonds. Finally, a 16 ML Bi (11̅0) slab is also constructed to simulate the topological (11̅0) surface of three-dimensional bulk Bi as a topological crystalline insulator (TCI). Furthermore, the consistent topological properties and slightly lower thermodynamic ORR overpotential (η = 0.53 V) are also observed on the thicker slab.

25 ENERGY STORAGE↗
DOE OSTI2023

Gasification of Coal and Biomass: The Route to Net-Negative-Carbon Power and Hydrogen

One promising process that is a candidate for meeting the goals of the US Department of Energy’s 21st Century Power Plant initiative is to gasify a mixture of coal and biomass to yield a syngas, which can have CO2 removed and then be used to produce hydrogen as well as an off-gas that can be used to flexibly produce power. This concept would overall be carbon net-negative and readily meet the 21st Century Power Plant initiative targets of smaller scale MW generation, high ramp rates and turndown, feedstock flexibility, and high efficiency—at a reasonable cost. Moreover, adding the large-scale production of “ultra-green” hydrogen yields a system tailored for the coming hydrogen economy, providing long-term energy storage and an attractive co-product for sale. The objective of the work being led by the Electric Power Research Institute, Inc. (EPRI), with support by Bechtel Corporation (Bechtel), Gas Technology Institute (GTI), Hamilton Mauer International, Inc. (HMI), Nebraska Public Power District (NPPD), NexantECA, Inc. (Nexant), and Wärtsilä, is to perform a front-end design and engineering (FEED) study on an oxygen-blown gasification system coupled with water-gas shift, pre-combustion CO2 capture, and pressure-swing adsorption working off a coal/biomass mix to yield high-purity hydrogen and a fuel off-gas that can generate power. Several designs are being considered that will be capable of producing 50 MW net from a flexible generator, over 8500 kg/hr of hydrogen, and net-negative CO2 emissions, at an efficiency of 50% net HHV. The plant would be hosted at an NPPD site, where opportunities for enhanced oil recovery and sequestration have been investigated and the need for low-carbon power and hydrogen is imminent. The principal biomass to be used is corn stover—prevalent in Nebraska where the plant will be located—mixed with Powder River Basin (PRB) coal, necessitating a gasifier that can use this feedstock and be flexible to allow other types. Waste plastics will also be reviewed for use. Two oxygen-blown gasifiers have been identified as candidates that have done testing with biomass including corn stover: the GTI gasifier—a high-pressure, fluidized-bed type—and HMI’s, a lower pressure moving-bed type. Both have relative advantages that were investigated in the Phase I design study, with a resultant down select of one system for which the FEED will be performed in Phase II. The technical tasks for the project are: • Design Development: Completion of design activities necessary to provide inputs for the FEED study. Multiple design cases will be assessed with the selection of the optimal one for the FEED. • Investment Case Preparation: Development of the draft investment case for the proposed process with business cases performed for the proposed host site and two other locations. • Host Site Selection: Evaluation of the two potential host sites within NPPD’s portfolio to select the preferred candidate based on technical, economic, and environmental considerations. • Environmental Information Volume (EIV) Development: Completion of the EIV for the host site. • FEED Study: Completion of a FEED study based on the design selected in Phase I. A Greenhouse Gas Life Cycle Analysis will also be performed for the process. • Update Investment Case: Finalization of the investment case based on findings from the FEED. The advantages of the proposed project are significant. Having an engaged U.S. power utility willing to provide a host site that will produce energy from coal plus a deep and experienced team is critical; the process meets all the goals of DOE’s 21st Century Power Plant initiative at an estimated total plant cost of ~$880M and a production cost of hydrogen of ~$2/kg-H2 while producing net-negative carbon power. If developed, this process has real commercial potential in the United States—supported by EPRI’s initial review of the considerable interest from selected U.S. utilities—and elsewhere around the globe. The process has fewer environmental hurdles compared to other concepts, lowering regulatory and protest risks—providing a pathway to preserving the viability of a critical indigenous energy source by transforming its use to match a changing world. This presentation outlines the motivation for the effort, summarizes project plans, work completed to date, results of the Phase I effort and, and detailed work scope for the remainder of the project in the Phase II FEED effort.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Gasification of Coal and Biomass: The Route to Net-Negative-Carbon Power and Hydrogen

One promising process that is a candidate for meeting the goals of the US Department of Energy’s 21st Century Power Plant initiative is to gasify a mixture of coal and biomass to yield a syngas, which can have CO2 removed and then be used to produce hydrogen as well as an off-gas that can be used to flexibly produce power. This concept would overall be carbon net-negative and readily meet the 21st Century Power Plant initiative targets of smaller scale MW generation, high ramp rates and turndown, feedstock flexibility, and high efficiency—at a reasonable cost. Moreover, adding the large-scale production of “ultra-green” hydrogen yields a system tailored for the coming hydrogen economy, providing long-term energy storage and an attractive co-product for sale. The objective of the work being led by the Electric Power Research Institute, Inc. (EPRI), with support by Bechtel Corporation (Bechtel), Gas Technology Institute (GTI), Hamilton Mauer International, Inc. (HMI), Nebraska Public Power District (NPPD), NexantECA, Inc. (Nexant), and Wärtsilä, is to perform a front-end design and engineering (FEED) study on an oxygen-blown gasification system coupled with water-gas shift, pre-combustion CO2 capture, and pressure-swing adsorption working off a coal/biomass mix to yield high-purity hydrogen and a fuel off-gas that can generate power. Several designs are being considered that will be capable of producing 50 MW net from a flexible generator, over 8500 kg/hr of hydrogen, and net-negative CO2 emissions, at an efficiency of 50% net HHV. The plant would be hosted at an NPPD site, where opportunities for enhanced oil recovery and sequestration have been investigated and the need for low-carbon power and hydrogen is imminent. The principal biomass to be used is corn stover—prevalent in Nebraska where the plant will be located—mixed with Powder River Basin (PRB) coal, necessitating a gasifier that can use this feedstock and be flexible to allow other types. Waste plastics will also be reviewed for use. Two oxygen-blown gasifiers have been identified as candidates that have done testing with biomass including corn stover: the GTI gasifier—a high-pressure, fluidized-bed type—and HMI’s, a lower pressure moving-bed type. Both have relative advantages that are being investigated in the Phase I design study, with a resultant down select of one system for which the FEED will be performed in Phase II. The technical tasks for the proposed project are: • Design Development: Completion of design activities necessary to provide inputs for the FEED study. Multiple design cases will be assessed with the selection of the optimal one for the FEED. • Investment Case Preparation: Development of the draft investment case for the proposed process with business cases performed for the proposed host site and two other locations. • Host Site Selection: Evaluation of the two potential host sites within NPPD’s portfolio to select the preferred candidate based on technical, economic, and environmental considerations. • Environmental Information Volume (EIV) Development: Completion of the EIV for the host site. • FEED Study: Completion of a FEED study based on the design selected in Phase I. A Greenhouse Gas Life Cycle Analysis will also be performed for the process. • Update Investment Case: Finalization of the investment case based on findings from the FEED. The advantages of the proposed project are significant. Having an engaged U.S. power utility willing to provide a host site that will produce energy from coal plus a deep and experienced team is critical; the process meets all the goals of DOE’s 21st Century Power Plant initiative at an estimated total plant cost of ~$880M and a production cost of hydrogen of ~$2/kg-H2 while producing net-negative carbon power. If developed, this process has real commercial potential in the United States—supported by EPRI’s initial review of the considerable interest from selected U.S. utilities—and elsewhere around the globe. The process has fewer environmental hurdles compared to other concepts, lowering regulatory and protest risks—providing a pathway to preserving the viability of a critical indigenous energy source by transforming its use to match a changing world. This presentation will outline the motivation for the effort, summarize project plans, work completed to date, results of the Design Development task, and detailed work scope for the remainder of the project.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Characterization of Lanthanum Monazite Surface Chemistry and Crystal Morphology through Density Functional Theory and Experimental Approaches

Monazite is a rare earth element (REE)-containing mineral that consists of (REE)PO 4 formal units and is one of the most important sources of these critical materials. The concentration of REEs from mined monazite ore often involves froth flotation, which is a beneficiation process that enhances the efficiency of downstream processing. The effectiveness of froth flotation is largely governed by the ability of collector agents to selectively bind to monazite particles. Thus, a molecular-level understanding of monazite interfacial chemistry is integral to the design of effective collector agents. To address this need, we performed density functional theory (DFT) calculations and a variety of experimental techniques to characterize La-monazite and elucidate its crystal morphology. Interestingly, we find minimal differences in the predicted morphologies of La-monazite for hydrous and anhydrous environments, which are largely dominated by low-index facets (e.g., {110}, {100}, and {010}). Indexing of synthesized La-monazite crystals via X-ray diffraction also uncovers {110} and {100} as the predominant facets. The average surface energies of 0% and 100% water coverage La-monazite crystals were predicted to be 0.87 and 0.76 J/m 2 , respectively, while calorimetry suggests values of 1.30 and 1.15 J/m 2 , respectively. The apparent discrepancies between the theoretical and experimental values are expected and attributed to defects present in physical crystals, in contrast to the perfect mineral surfaces in simulations. The difference in surface energy between the 0% and 100% water coverage morphologies predicted by theory is consistent with the value measured via calorimetry. DFT reveals a wide range of adsorption energies for water across the studied facets, but in all cases, water is predicted to strongly bind to monazite surfaces with an average adsorption energy of -92.7 kJ/mol for a La-monazite single crystal. Finally, this study provides the groundwork necessary for the rational design of froth flotation collector agents by granting molecular-level insight into the predominant facets of monazite.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Effect of the Chemical States of Copper on Methanol Decomposition and Oxidation

Here, the decomposition and oxidation reactions of CH 3 OH over metallic Cu(100) and Cu 2 O-covered Cu(100) surfaces are studied using a combination of in-situ ambient-pressure X-ray photoelectron spectroscopy, Auger electron spectroscopy, and density functional theory calculations. We identify the sequential chemical transformation pathways from bond cleavage to the formation of intermediates and final products under operational conditions. Accumulative surface adsorption of CH 3 O species on metallic Cu(100) impedes the decomposition of CH 3 OH. Co-dosing on metallic Cu(100) with low pressures of 1·10 -4 Torr CH 3 OH + 1·10 -4 Torr O 2 results in partial oxidation of CH 3 OH, where the chemisorbed O ads reduces surface sites available for CH 3 O adsorption, decreasing the surface activity for CH 3 OH decomposition. In contrast, the Cu 2 O overlayer formed under the elevated pressures of 0.33 Torr CH 3 OH + 0.66 Torr O 2 promotes the total oxidation of CH 3 OH into the final products of CO 2 and H 2 O, arising from the active reaction 2 between lattice O within Cu 2 O and intermediates of CH 3 O, CH 2 O, HCOO, and CO. Despite the more favorable O-H bond scission, C-O bond scission also occurs to result in surface accumulation of CH x on metallic Cu(100), blocking active sites for decomposition reactions of CH 3 OH and CH 3 O. By comparison, the CH x species on the Cu 2 O-covered Cu(100) undergo oxidation into CO 2 and H 2 O with lattice O in the Cu 2 O overlayer, thereby freeing active sites for the total oxidation of CH 3 OH. These results highlight the distinct roles of metallic Cu and Cu 2 O in the pathways of CH 3 OH decomposition and oxidation reactions, offering practical insights for the design of Cu-based catalysts with tailored reactivity and selectivity.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Product-promoted acetylene cyclotrimerization to benzene on Ag(111)

Acetylene cyclotrimerization to benzene on Ag(111) has recently been found to be 100% selective. However, it requires monolayer coverages, limiting its practical application due to the high pressure required to attain this surface coverage of acetylene near room temperature. Here, we show that co-adsorbed benzene, the reaction product, promotes cyclotrimerization at submonolayer acetylene coverages without compromising the 100% selectivity of Ag(111) via temperature-programmed desorption experiments. Scanning tunneling microscopy and density functional theory (DFT) calculations elucidate the origin of this effect whereby attractive acetylene–benzene interactions locally compress acetylene domains. DFT calculations further illustrate how co-adsorbed benzene reduces the transition-state energy for formation of the key C 4 intermediate, making cyclotrimerization competitive with desorption. Together, these findings reveal how product-reactant interactions can enhance C–C coupling.

Acetylene cyclotrimerization↗
NASA NTRS1997

Extraterrestrial Helium (He@C60) Trapped in Fullerenes in the Sudbury Impact Structure

Fullerenes (C60 and C70) have recently been identified in a shock-produced breccia (Onaping Formation) associated with the 1.85-Ga Sudbury Impact Crater. The presence of parts-per-million levels of fullerenes in this impact structure raises interesting questions about the processes that led to the formation of fullerenes and the potential for delivery of intact organic material to the Earth by a large bolide (e.g., asteroid or comet). Two possible scenarios for the presence of fullerenes in the Sudbury impact deposits are that (1) fullerenes are synthesized within the impact plume from the C contained in the bolide; or (2) fullerenes are already present in the bolide and survived the impact event. The correlation of C and trapped noble gas atoms in meteorites is well established. Primitive meteorites contain several trapped noble gas components that have anomalous isotopic compositions, some of which may have a presolar origin. Several C-bearing phases, including SiC, graphite, and diamond, have been recognized as carriers of trapped noble gases. It has also been suggested that fullerenes (C60 and C70) might be a carrier of noble gas components in carbonaceous chondrites. Recently, fullerenes have been detected in separate samples in the Allende meteorite. Carbon-60 is large enough to enclose the noble gases He, Ne, Ar, Kr, and Xe, but it is too small to contain diatomic gases such as N2 or triatomic gases such as CO2. Recent experimental work has demonstrated that noble gases of a specific isotopic composition can be introduced into synthetic fullerenes at high temperatures and pressures; these encapsulated gases can then be released by the breaking of one or more C bonds during step-heating under vacuum. These thermal-release patterns for He encapsulated within the C60 molecule (He@C60) are similar to the patterns for acid residues of carbonaceous chondrites, suggesting that fullerenes could be an additional carrier of trapped noble gases in acid residues of meteorites. Analysis and Results: In order to characterize the noble gas compositions of the Sudbury fullerenes, we undertook a systematic study of acid-resistant residues throughout the C-rich layer (Black member) of the Onaping Formation. Samples were demineralized and extracted using standard techniques. The Onaping extracts were analyzed using several techniques, including UV-Vis adsorption, electro spray mass spectrometry, and laser desorption (linear and reflectron) time-of-flight (TOF) mass spectrometry (LDMS). The Sudbury fullerenes were then separated and purified using HPLC coupled with a photo diode array detector. The HPLC extracts containing the purified fullerenes were loaded into a metal tube furnace within a glove box under a N atmosphere in preparation for noble gas analyses. The 3-He and 4-He content of the fullerene extracts was measured using previously reported standard techniques . Discussion: Fullerenes (C60 and C70) in the Sudbury Impact Structure have been found to contain trapped He with a 3-He/4-He ratio greater than 5 x 10(exp -4). The 3-He/4-He ratio exceeds the accepted solar value by more than 30% and is more than 10x higher than the maximum reported mantle value. Terrestrial nuclear reactions or cosmic-my bombardment are not sufficient to generate such a high ratio. The 3-He/4-He ratios in the Sudbury fullerenes are similar to those determined for interplanetary dust particles. The greater-than-solar ratios of 3-He/4-He in the Sudbury fullerenes may indicate a presolar origin, although alternative mechanisms occurring in the ISM to explain these high ratios (e.g., spallation reactions, selective He implantation, etc.) cannot be entirely ruled out. We are currently attempting to isolate enough fullerene material to measure anomalous Ne (or Kr or Xe) contained within the C60 (e.g., the "pure" 22-Ne component) and thus determine whether the Sudbury fullerenes are indeed presolar in origin.

Becker, L.↗
DOE OSTI2024

Analytical Tools to Assess Polymer Biodegradation: A Critical Review and Recommendations

Many petroleum-derived plastic materials are highly recalcitrant and persistent in the environment, posing significant threats to human and ecological receptors due to their accumulation in ecosystems. In recent years, research efforts have focused on advancing biological methods for polymer degradation. Enzymatic depolymerization has emerged as particularly relevant for biobased plastic recycling, potentially scalable for industrial use. Biodegradation involves adsorption to the plastic solid surface, followed by an interfacial reaction, resulting in cleavage of bonds of polymer chains exposed on the surface. Here, widely varying substrate-specific kinetics are observed, with the polymer’s properties possessing a significant impact on the rate of this interfacial catalysis. Thus, there is a critical need for sensitive and accurate characterization of the material surface during and after interfacial depolymerization to fully understand the reaction mechanisms. Here, we provide a critical review of a range of techniques used in the analysis of material surfaces to characterize the chemical, topological, and morphological features relevant to the study of enzymatic biocatalysis, including microscopy techniques, spectroscopic techniques (e.g., X-ray diffraction analysis, Fourier transform infrared attenuated total reflectance spectroscopy, and mass spectrometry detection of analytes associated with degradation). Techniques for evaluation of surface energy and topology in their relevancy for sensitive detection of biological surface modifications are also discussed. In addition, this paper provides an overview of the strengths of these techniques and compares their performance in both sensitivity and throughput, including emerging techniques, which can be useful, particularly for the rapid analysis of the surface properties of polymeric materials in high-throughput screening of candidate biocatalysts. This research serves as a starting point in selecting and applying appropriate methodologies that provide direct evidence to the ongoing biotic degradation of polymeric materials.

Colachis, Matthew↗
DOE OSTI2020

Sensitivity Analysis and Effective Parametrization of PEM Fuel Cell Models

The cost of proton-exchange-membrane fuel cells (PEMFCs) remains a major hurdle in large-scale commercialization of this technology. To improve their performance and reduce cost, novel materials and electrode designs are continuously envisioned, e.g., non-PGM catalyst layers, ultra-thin Pt/Pt-Ni based catalyst layers, structured ionomer arrays or NSTF catalyst layers.1 Understanding the impact of these improvement strategies can be extremely time and cost intensive due to complex physical phenomena and large design space. We have previously developed a PEMFC modeling framework2 which has been a time and cost effective tool for understanding and optimizing the complex multi-physics phenomena within PEMFCs; however, several of the cell parameters used in the modeling have large spread in measured data.3 Furthermore, several transport parameters such as water adsorption kinetics have not been accurately measured and the approximations are spread over several orders of magnitude. These uncertainties cause problems in ascertaining accuracy of the modeling approach and they reduce the predictive power of the numerical models. The aim of this work is to identify the sensitivity of PEFC numerical model outputs to various input parameters. The previously in-house developed MEA modeling framework2 is used for PEMFC modeling. The sensitivity of the model outputs with respect to inputs parameters is obtained by analyzing the condition numbers for different output-input pairs at varying operating conditions. An example of the sensitivity analysis is shown in Figure 1. The condition numbers are obtained for the entire possible range of input parameters at varying operating conditions to identify the most crucial parameters of the PEMFC model. Based on our preliminary analysis, parameters related to kinetics (exchange current density and ECSA) and heat/water management in electrodes and ionomer (ionomer fraction, thermal conductivity) are most crucial. One of the major goals of this work is to identify the most crucial set of parameters towards which the model shows maximum sensitivity. This will guide future experimentalists to measure these properties with higher accuracy. Furthermore, the sensitivity analysis will also enable us to optimize the PEMFC performance by selectively targeting the most sensitive parameters and thereby making the largest impact. Acknowledgements The work is funded under the Fuel Cell Performance and Durability Consortium (FC-PAD), by the Fuel Cell Technologies Office (FCTO), Office of Energy Efficiency and Renewable Energy (EERE), of the U.S. Department of Energy under contract number DE-AC02-05CH11231. The authors would like to thank Nathan Craig at Robert Bosch LLC for his valuable input in designing the sensitivity analysis. The authors would also like to thank Giovanna Bucci and Matthias Hanauer at Robert Bosch for their valuable inputs and discussion. References P. K. Sinha, W. Gu, A. Kongkanand and E. Thompson, J. Electrochem. Soc., 158, B831 (2011). L. M. Pant, M. R. Gerhardt, N. Macauley, R. Mukundan, R. L. Borup and A. Z. Weber, Electrochim. Acta, 326, 134963 (2019). R. Vetter and J. O. Schumacher, ArXiv181110091 Phys. (2018). Figure 1

Pant, Lalit↗
DOE OSTI2021

Data from Reactive Species and Reaction Pathways for the Oxidative Cleavage of 4-Octene and Oleic Acid with H2O2 over Tungsten Oxide Catalysts

Oxidative cleavage of carbon–carbon double bonds (C═C) in alkenes and fatty acids produces aldehydes and acids valued as chemical intermediates. Solid tungsten oxide catalysts are low cost, nontoxic, and selective for the oxidative cleavage of C═C bonds with hydrogen peroxide (H2O2) and are, therefore, a promising option for continuous processes. Despite the relevance of these materials, the elementary steps involved and their sensitivity to the form of W sites present on surfaces have not been described. Here, we combine in situ spectroscopy and rate measurements to identify significant steps in the reaction and the reactive species present on the catalysts and examine differences between the kinetics of this reaction on isolated W atoms grafted to alumina and on those exposed on crystalline WO3 nanoparticles. Raman spectroscopy shows that W–peroxo complexes (W–(η2-O2)) formed from H2O2 react with alkenes in a kinetically relevant step to produce epoxides, which undergo hydrolysis at protic surface sites. Subsequently, the CH3CN solvent deprotonates diols to form alpha-hydroxy ketones that react to form aldehydes and water following nucleophilic attack of H2O2. Turnover rates for oxidative cleavage, determined by in situ site titrations, on WOx–Al2O3 are 75% greater than those on WO3 at standard conditions. These differences reflect the activation enthalpies (ΔH‡) for the oxidative cleavage of 4-octene that are much lower than those for the isolated WOx sites (36 ± 3 and 60 ± 6 kJ·mol–1 for WOx–Al2O3 and WO3, respectively) and correlate strongly with the difference between the enthalpies of adsorption for epoxyoctane (ΔHads,epox), which resembles the transition state for epoxidation. The WOx–Al2O3 catalysts mediate oxidative cleavage of oleic acid with H2O2 following a mechanism comparable to that for the oxidative cleavage of 4-octene. The WO3 materials, however, form only the epoxide and do not cleave the C–C bond or produce aldehydes and acids. These differences reflect the distinct site requirements for these reaction pathways and indicate that acid sites required for diol formation are strongly inhibited by oleic acids and epoxides on WO3 whereas the Al2O3 support provides sites competent for this reaction and increase the yield of the oxidative cleavage products.

Catalysis↗
DOE OSTI2025

Enabling Solar Water Oxidation by BiVO 4 in Strongly Acidic Solutions

The oxygen evolution reaction (OER) is paired with various electrochemical and photoelectrochemical reduction reactions used for fuel and chemical production. As there is a strong interest in performing many of these reduction reactions in strongly acidic solutions to increase the reaction rate, efficiency, or selectivity, there is also a great interest in enabling efficient and stable OER in strongly acidic solutions. In this study, we report stable photoelectrochemical OER (POER) of a BiVO 4 photoanode in 0.1 M HNO 3 (pH 1). This was achieved by using Nb 2 O 5 as a protection layer. While Nb 2 O 5 was rarely used as a protection layer for photoelectrodes in the past, we show its excellent capability to suppress both the chemical and photoelectrochemical dissolution of BiVO 4 at pH 1. After stabilizing BiVO 4 with a Nb 2 O 5 protection layer, we added Co 2+ ions to the electrolyte as an OER catalyst to enhance the POER. We found that Co (aq) 2+ can serve as a homogeneous OER catalyst without being deposited as a CoO x solid catalyst on Nb 2 O 5 . When we performed the POER using unprotected BiVO 4 with Co (aq) 2+ under the same condition, although POER was enhanced, the enhancement could not be sustained due to the chemical dissolution of BiVO 4 . After the POER, we found that a Co 3+ -containing OER catalyst was deposited on the bare BiVO 4 surface. This result suggested that the use of Co 2+ ions as a homogeneous catalyst was possible due to the inertness of the Nb 2 O 5 surface toward the adsorption or deposition of Co ions. This study enabling stable POER of BiVO 4 in 0.1 M HNO 3 using the combination of a Nb 2 O 5 protection layer and Co (aq) 2+ as a homogeneous OER catalyst provides promising possibilities for acidic POER and OER.

Catalysts↗