Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “scaled testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

NASA/FAA general aviation crash dynamics program

The program involves controlled full scale crash testing, nonlinear structural analyses to predict large deflection elastoplastic response, and load attenuating concepts for use in improved seat and subfloor structure. Both analytical and experimental methods are used to develop expertise in these areas. Analyses include simplified procedures for estimating energy dissipating capabilities and comprehensive computerized procedures for predicting airframe response. These analyses are developed to provide designers with methods for predicting accelerations, loads, and displacements on collapsing structure. Tests on typical full scale aircraft and on full and subscale structural components are performed to verify the analyses and to demonstrate load attenuating concepts. A special apparatus was built to test emergency locator transmitters when attached to representative aircraft structure. The apparatus is shown to provide a good simulation of the longitudinal crash pulse observed in full scale aircraft crash tests.

Thomson, R. G.↗
NASA NTRS1972

Transonic wind tunnel tests of a .015 scale space shuttle booster model

Details of the test program, an outline of the test procedure, and results of the investigation in tabular form are presented. The base drag reduction potential was determined at cruise conditions (M = .40) of a modified base region, with and without base bleed flow. Transonic effects and cruise control effectiveness of the new base region were also obtained. The tests were performed at Mach numbers from 0.40 to 1.10, at angles of attack from -4 to +20 degrees and at angles of sideslip from -6 to +6 degrees, all at a Reynolds number of 6.56 million per meter (2.0 million per foot).

Dennis, R. J.↗
NASA NTRSDate not supplied

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗
NASA NTRS1981

Ground effect hover characteristics of a large-scale twin tilt-nacelle V/STOL model

This paper is a summary of an analysis of the ground-effect characteristics of a large-scale twin-engine, tilt-nacelle V/STOL model. The analysis considers data from the flow field beneath the full-scale model, as well as small-scale model test data, and makes comparisons with jet-ground interactions predicted by a computer code. The data from the large-scale test comprise ground-plane surface temperatures, static pressure distribution and wall-jet total-pressure profiles, fuselage undersurface static pressures, and model forces and moments. The results indicate that the near-field flow is more complex than is indicated by either the small-scale uniform jet studies or the computer predictions. The far-field flow characteristics do show some similarity for these three cases.

Dudley, M. R.↗
NASA NTRS1976

Results of heat transfer tests of a 0.0175-scale space shuttle vehicle 5 model (60-OTS) in the NASA-Ames Research Center 3.5-foot hypersonic wind tunnel (test IH48)

Heat transfer data are presented for a .0175-scale model of the Rockwell International Space Shuttle Vehicle 5. The primary purpose of these tests was to obtain aerodynamic interference heating data on the external tank in the tank alone, second-, and first-stage configurations. Data were also obtained on the Orbiter and solid rocket boosters. Nominal Mach Nos. of 5.2 and 5.3 at nominal freestream unit Reynolds numbers of 1.5 and 5.0 million per foot, respectively, were investigated. Photographs of the tested configurations and test equipment are shown.

Dye, W. H.↗
NASA NTRS1985

Performance and loads data from a hover test of a full-scale XV-15 rotor

A hover test of a full-scale XV-15 rotor was conducted at the Outdoor Aerodynamic Research Facility at Ames Research Center. The primary objective of the test was to obtain accurate measurements of the hover performance of the original, metal-blade XV-15 rotor system. Data were acquired for rotor tip Mach numbers ranging from 0.60 to 0.73. This report presents data on rotor performance, rotor wake downwash velocities, and rotor loads.

Felker, F. F.↗
NASA NTRSDate not supplied

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗
NASA NTRS1979

Icing testing in the large Modane wind-tunnel on full-scale and reduced scale models

Icing tests on full scale models of parts of aircraft (wings, tailplanes, radome) equipped with actual de-icing systems were carried out in the large Modane wind tunnel of ONERA. For studying icing on the Concorde, it was necessary to use a 1/6 scale half model. The equations governing the relevant parameter ratios to obtain reasonably good similitude water catching and ice accretion are recalled. Despite the inherent limitations of this particular kind of testing, i.e., the impossibility of duplicating both the Mach and Reynolds conditions for the main flow pattern, it is possible to obtain on a reduced scale model a reasonably good representation of icing cloud catching and of the shape of resulting ice accretion.

Charpin, F.↗
NASA NTRS1937

The Scale Effect in Towing Tests with Airplane-float Systems

The present report includes a description of the making of three-component measurements on a full-size float mounted on an actual airplane and the comparison of the results with those from two models of the same form but of different size which had been tested in the towing tank. The purpose of the comparison is to determine the effect of the Reynolds Number on the results of model tank tests. Following a brief discussion of previous tests intended to elucidate the problem of scale effect on float systems and a description of the testing equipment, the choice of the reference quantities to be used in the comparison is discussed. The selection of load, speed, and trim as a basis of comparison seems best suited to the practical operation of making this comparison. The quantities affected by scale are then: resistance, trimming moment, and their derivatives; planing number (resistance/weight on water); and position of center of pressure.

Schmidt, Rudolph↗
NASA NTRS1993

Numerical simulation of a complete STOVL aifcraft in ground effect

The aerodynamic environment encountered by powered-lift aircraft operating in ground effect is unique among flight vehicles. It is characterized by low forward speed with embedded regions of high subsonic or supersonic jet flows. During ground effect operations, complex recirculating flows generated by the jets produce large changes in the aerodynamic loads on the flight vehicle. Analytic prediction and small-scale experimental methods have produced mixed results in this flight regime, with the result that costly full-scale powered tests are required to evaluate the performance of candidate designs. The ability to accurately predict vehicle performance without resorting to full-scale tests will be critical to future powered-lift aircraft projects. This paper summarizes efforts to predict the flow field about a powered-lift aircraft, the YAV-8B Harrier, in low level jet-borne flight by solution of the Reynolds-averaged Navier-Stokes equations. Results are compared to infrared images of the NASA YAV-8B Harrier V/STOL Systems Research Aircraft (VSRA) under similar flight conditions.

Smith, Merritt H.↗
NASA NTRS1993

Full-scale wind-tunnel tests of high-lift system modifications on a carrier based fighter aircraft

Modifications to the high-lift system of a full-scale F/A-I8A were tested in the 80- by 120-Foot Wind Tunnel of the National Full-Scale Aerodynamics Complex at the NASA Ames Research Center in Moffett Field, California. The objective was to measure the effect of simple modifications on the aerodynamic performance of the high-lift system. The modifications included the placement of a straight fairing in the shroud cove above the trailing-edge flap and the addition of seals to prevent air leakage through the hinge lines of the leading-edge flap, the trailing-edge shroud, and the wing fold. The test was carried out on an actual F/A-18A with it's flaps deployed in the landing approach configuration. The angle of attack ranged from 0 to 16 degrees and the wind speed was 100 knots. At an angle of attack of 8 degrees, the trimmed lift coefficient was improved by 0.09 with all wing seals in place. This corresponds to a reduction in the approach speed for the F/A-I8A of about 5 knots. The seal along the wing fold hinge, a feature present on many naval aircraft, provided one third of the total increment in trimmed lift. A comparison of the full-scale wind-tunnel results with those obtained from flight test is also presented.

Meyn, Larry A.↗
NASA NTRS2018

Development and Initial Testing of the Tiltrotor Test Rig

The NASA Tiltrotor Test Rig (TTR) is a new, large-scale proprotor test system, developed jointly with the U.S. Army and Air Force, to develop a new, large-scale proprotor test system for the National Full-Scale Aerodynamics Complex (NFAC). The TTR is designed to test advanced proprotors up to 26 feet in diameter at speeds up to 300 knots, and even larger rotors at lower airspeeds. This combination of size and speed is unprecedented and is necessary for research into 21st-century tiltrotors and other advanced rotorcraft concepts. The TTR will provide critical data for validation of state-of-the-art design and analysis tools.

Proprotor↗
NASA NTRS1947

Wind-Tunnel Tests of a 0.182-Scale Model of an F4U-1 Airplane with External Stores

Tests were made in the Langley 7- by 10-foot tunnel on a 0.182-scale model of an F4U-1 airplane with external stores. This paper is concerned mainly with presenting the data obtained in this investigation and with a comparison of some of these data with flight-test results determining the feasibility of estimating flight buffet Mach number from tunnel data. The results of this investigation indicate that the incremental drag coefficient due to external stores may be used to estimate the maximum Mach number that the F4U-1 airplane may reach in flight when it is equipped with external stores. This estimation is conservative for the five configurations investigated by mounts varying from 0 to 10 percent of the flight limit Mach number. The free-stream tunnel Mach number corresponding to sonic flow over the lower surface of the wing in the region of the store is a good indication of the lower limit of buffet in flight of the F4U-1 airplane when equipped with external stores. The fluctuations of total pressure over the horizontal tail are not sufficiently large (maximum of 1 percent q(sub o) to cause buffeting of the airplane.

Silvers, H. Norman↗
NASA NTRS1975

Results of pressure distribution tests of a 0.010-scale space shuttle orbiter model (61-0) in the NASA/ARC 3.5-foot hypersonic wind tunnel (test OH38), volume 1

Test results are presented of hypersonic pressure distributions at simulated atmospheric entry conditions. Pressure data were obtained at Mach numbers of 7.4 and 10.4 and Reynolds numbers of 3.0 and 6.5 million per foot. Data are presented in both plotted and tabulated data form. Photographs of wind tunnel apparatus and test configurations are provided.

Dye, W. H.↗