SEARCH · Engineering Papers

Results for “process design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS2004

Modelling and Analysis of a Regenerative Fuel Cell Propulsion System for a High Altitude Long Endurance UAV

In the search to bridge current gaps in surveillance and communication technologies, a new type of, aircraft is currently undergoing design. The idea of a High Altitude Long Endurance (HALE) aircraft is already a few decades old, but has only recently become realizable. A relay and collector of information at altitudes of 65,000 feet and higher could greatly improve standards of data exchange, homeland security, and research of the air, land and sea. NASA, as a major force in propulsion research, is exploring methods of powering an autonomous aircraft for days, weeks, or even months without refueling. Such a task requires not only high energy density, but also the ability to make use of renewable energy sources to regenerate power. Hydrogen is one of the most energy dense fuels available. Fuel cells make use of hydrogen by harnessing the energy released as it combines with oxygen to produce electricity and water. Fuel cells are envisioned to occupy future propulsion systems in cooperation with solar cells where the photovoltaic arrays harness sunlight into power which can electrolize the water byproduct into reusable hydrogen and oxygen. Modeling this type of system requires adequate assumptions of support hardware and daily transients in operation. The performance of a regenerative fuel cell propulsion system lies in the flight characteristics (altitude, density, temperature, latitude, etc.). Each subsystem is defined by many parameters which can be varied across wide ranges. Statistical and probabilistic analyses bring forward a wealth of information that can be utilized in the design process. This is necessary since the required technologies are relatively young and barely, if yet, capable. Once the modeling is complete, a design space exploration of this highly constrained scenario can be utilized to find the optimal design. The model will become an interactive environment with which experiments and tests can be run. When linked

Simpson, Mike B.↗

NASA NTRS2006

Rapid Assessment of Aircraft Structural Topologies for Multidisciplinary Optimization and Weight Estimation

Algorithms for rapid generation of moderate-fidelity structural finite element models of air vehicle structures to allow more accurate weight estimation earlier in the vehicle design process have been developed. Application of these algorithms should help to rapidly assess many structural layouts before the start of the preliminary design phase and eliminate weight penalties imposed when actual structure weights exceed those estimated during conceptual design. By defining the structural topology in a fully parametric manner, the structure can be mapped to arbitrary vehicle configurations being considered during conceptual design optimization. Recent enhancements to this approach include the porting of the algorithms to a platform-independent software language Python, and modifications to specifically consider morphing aircraft-type configurations. Two sample cases which illustrate these recent developments are presented.

Samareh, Jamshid A.↗

NASA NTRS2008

Multidisciplinary Design, Analysis, and Optimization Tool Development using a Genetic Algorithm

Multidisciplinary design, analysis, and optimization using a genetic algorithm is being developed at the National Aeronautics and Space A dministration Dryden Flight Research Center to automate analysis and design process by leveraging existing tools such as NASTRAN, ZAERO a nd CFD codes to enable true multidisciplinary optimization in the pr eliminary design stage of subsonic, transonic, supersonic, and hypers onic aircraft. This is a promising technology, but faces many challe nges in large-scale, real-world application. This paper describes cur rent approaches, recent results, and challenges for MDAO as demonstr ated by our experience with the Ikhana fire pod design.

Pak, Chan-gi↗

NASA NTRS2020

The New NASA Approach to Reliability and Maintainability

In 2017, after 20 years, NASA issued a major revision of its reliability and maintainability (R&M) policy, NASA-STD- 8729.1A. Formerly NASA required certain specific R&M activities during each succeeding phase of project development. Now NASA requires a project to start by including the initial development of R&M requirements and the devising of strategies to implement and verify them. Rather than resolving all the requirements first and then designing the system, as has been usual in systems design, the design process now is to work top down by layers. It begins by first identifying the top level requirements and suggesting top level design strategies for those, then making these higher strategies the basis for a lower level set of requirements, and so on down to the lowest components. This approach is intended to ensure that R&M is designed in from the beginning rather than added later with difficulty to a completed design concept. The new R&M standard uses an innovative and effective top-down system design approach intended to effectively implement R&M.

Jones, Harry W.↗

NASA NTRS2020

The New NASA Approach to Reliability and Maintainability

In 2017, after 20 years, NASA issued a major revision of its reliability and maintainability (R&M) policy, NASA-STD-8729.1A [1]. Formerly NASA required certain specific R&M activities during each succeeding phase of project development. Now NASA requires a project to start by including the initial development of R&M requirements and the devising of strategies to implement and verify them. Rather than resolving all the requirements first and then designing the system, as has been usual in systems design, the design process now is to work top down by layers. It begins by first identifying the top level requirements and suggesting top level design strategies for those, then making these higher strategies the basis for a lower level set of requirements, and so on down to the lowest components. This approach is intended to ensure that R&M is designed in from the beginning rather than added later with difficulty to a completed design concept. The new R&M standard uses an innovative and effective top-down system design approach intended to effectively implement R&M.

Jones, Harry W.↗

NASA NTRSDate not supplied

Conceptual Design of Propulsors for the SUSAN Electrofan Transport Aircraft

Conceptual designs of the propulsor modules for the SUSAN electro-fan aircraft are sought after. Shaft power requirement is reduced by using boundary layer ingesting propulsion technology. There are several obstacles to designing feasible BLI propulsion systems such as inlet distortion, flow blockage from ingesting low-momentum flow, strong coupling between airframe and propulsion systems. Thus, the high fidelity CFD tool is indispensable to assess the performance of the propulsion systems and evaluate the inlet profiles during the design process. Consequently, the CFD data is used to update the inputs for the NPSS model from the initial stage of the system design. Hence, the inlet sizing, fan design, and estimation of the power saving are carried out. Various installation concepts of the mail-slot nacelle, such as under-/over-wing and trailing edge configurations, are investigated for the wing-mounted turbo-electric distributed propulsor module, and their power-saving is evaluated. As for the tail-mounted turbofan engine, the fan diameter and inlet captured area is determined based on the CFD profiles. An appropriate area ratio of the bypass and core ducts is derived from meeting the target bypass ratio from the system design. The baseline fan stage is analyzed by full annulus URANS CFD to assess the efficiency penalty due to the ingested pressure and swirl distortions.

SUSAN Electro-Fan Aircraft↗

NASA NTRSDate not supplied

Conceptual Design of Propulsors for the SUSAN Electrofan Transport Aircrafts

Electric Aircraft↗

NASA NTRSDate not supplied

Semantic Search with Sentence-BERT for Design Information Retrieval

Managing and referencing design knowledge is a critical activity in the design process. However, reliably retrieving useful knowledge can be a frustrating experience for users of knowledge management systems due to inherent limitations of standard keyword-based searches. In this research, we consider the task of retrieving relevant lessons learned from the NASA Lessons Learned Information System (LLIS). To this end, we apply a state-of-the-art natural language processing (NLP) technique for information retrieval (IR): semantic search with sentence-BERT, which is a modification of a Bidirectional Encoder Representations from Transformers (BERT) model that uses siamese and triplet network architectures to obtain semantically meaningful sentence embeddings. While the pre-trained sBERT model performs well out-of-the-box, we further fine-tune the model on data from the LLIS so that it learns on design engineering-relevant vocabulary. We quantify the improvement in query results using both standard sBERT and fine-tuned sBERT over a keyword search. Our use case throughout the paper is to use queries related to specific requirements from a NASA project. Fine tuning the sBERT model on LLIS data yields a mean average precision (MAP) of 0.807 on queries based on information needs from a real NASA project. Results indicate that applying state-of-the-art natural language processing techniques, especially when finetuned using engineering data, to design information retrieval tasks shows significant promise in modernizing design knowledge management systems.

Hannah S. Walsh↗

NASA NTRS2011

Human Rating the Orion Parachute System

Human rating begins with design. Converging on the requirements and identifying the risks as early as possible in the design process is essential. Understanding of the interaction between the recovery system and the spacecraft will in large part dictate the achievable reliability of the final design. Component and complete system full-scale flight testing is critical to assure a realistic evaluation of the performance and reliability of the parachute system. However, because testing is so often difficult and expensive, comprehensive analysis of test results and correlation to accurate modeling completes the human rating process. The National Aeronautics and Space Administration (NASA) Orion program uses parachutes to stabilize and decelerate the Crew Exploration Vehicle (CEV) spacecraft during subsonic flight in order to deliver a safe water landing. This paper describes the approach that CEV Parachute Assembly System (CPAS) will take to human rate the parachute recovery system for the CEV.

Machin, Ricardo A.↗

NASA NTRS1981

Process characteristics and design methods for a 300 deg quad OP amp

The results of process characterization, circuit design, and reliability studies for the development of a quad OP amplifier intended for use up to 300 C are presented. A dielectrically isolated complementary vertical bipolar process was chosen to fabricate the amplifier in order to eliminate isolation leakage and the possibility of latch up. Characterization of NPN and PNP junctions showed them to be suitable for use up to 300 C. Interconnect reliability was predicted to be greater than four years mean time between failure. Parasitic MOS formation was eliminated by isolation of each device.

Beasom, J. D.↗

NASA NTRS2002

Surface Enhancement Improves Crack Resistance

The low plasticity burnishing (LPB) process produces a deep layer of surface compression in a quick and affordable manner to produce metal surfaces free of scratches, nicks, and gouges. The process, designed for easy inclusion in the manufacturing environment, can be performed with conventional Computer Numerical Control machine tools. This allows parts to be processed during manufacturing, rather than as a post process in a separate facility. A smooth, free-rolling spherical ball suspended in a fluid allows for single-point contact. The ball comes into mechanical contact only with the surface to be burnished, and can be moved in any direction. LPB can be applied to all types of carbon and alloy steel, stainless steel, cast iron, aluminum, titanium, and nickel- based super alloys. In addition to improving a surface's resistance to fatigue and damage, treatment stops the growth of shallow cracks. The LPB process is used on the leading edges of turbine blades to improve resistance to foreign object damage and crack growth. This means significant savings for aircraft owners, since maintenance requirements to inspect for fatigue damage, replace parts, and remove corrosion damage increase the cost of operation.

Source record↗

NASA NTRSDate not supplied

Oversimplification of Systems Engineering Goals, Processes, and Criteria in NASA Space Life Support

This paper investigates the oversimplification of the inherently complex systems engineering process in space life support. The standard systems engineering process steps are described. The International Space Station (ISS) life support system is explained with its goals and performance criteria. Although it is not usually emphasized, the essential function of developing a hierarchy of systems and subsystems is to simplify the design process. The System Complexity Metric (SCM) shows how this di-vide-and-conquer approach also reduces the system complexity. The complete systems engineering process has many detailed steps. It is often simplified because of the effort required and the human limitations on working memory and decision span. Systems analysis demands slow, logical, and fo-cused thinking but is often bypassed in favor of quick, intuitive, subconscious “gut feel.” A study of 100 system designs found examples of 12 specific mental mistakes, such as ignoring stakeholder needs, and these mistakes are essentially oversimplifications of the systems engineering process. An analysis of space life support goals, options, criteria, and processes found 11 examples of oversimplifications in systems engineering, such as neglecting safety and cost. All these 11 oversimplifications could be traced to one or more of the 12 previously identified mental mistakes or other well-known ones, such as ig-noring sunk costs. Oversimplification of the systems engineering process is rarely noticed but is a common and harmful problem. A study of failures in 50 different space systems found that problems in systems engineering caused failures and often led to errors in design, development, and test that further contributed to failure. It seems that more diligent systems engineering could prevent many project problems and failures, but projects seem to be more guided by “gut feel” based on tradition, authority, and consensus than on the logical, rational systems engineering approach.

Simplified systems engineering↗

NASA NTRS1990

Computational tools for multi-linked flexible structures

A software module which designs and tests controllers and filters in Kalman Estimator form, based on a polynomial state-space model is discussed. The user-friendly program employs an interactive graphics approach to simplify the design process. A variety of input methods are provided to test the effectiveness of the estimator. Utilities are provided which address important issues in filter design such as graphical analysis, statistical analysis, and calculation time. The program also provides the user with the ability to save filter parameters, inputs, and outputs for future use.

Lee, Gordon K. F.↗

NASA NTRS1991

Optimization techniques applied to passive measures for in-orbit spacecraft survivability

Spacecraft designers have always been concerned about the effects of meteoroid impacts on mission safety. The engineering solution to this problem has generally been to erect a bumper or shield placed outboard from the spacecraft wall to disrupt/deflect the incoming projectiles. Spacecraft designers have a number of tools at their disposal to aid in the design process. These include hypervelocity impact testing, analytic impact predictors, and hydrodynamic codes. Analytic impact predictors generally provide the best quick-look estimate of design tradeoffs. The most complete way to determine the characteristics of an analytic impact predictor is through optimization of the protective structures design problem formulated with the predictor of interest. Space Station Freedom protective structures design insight is provided through the coupling of design/material requirements, hypervelocity impact phenomenology, meteoroid and space debris environment sensitivities, optimization techniques and operations research strategies, and mission scenarios. Major results are presented.

Mog, Robert A.↗

NASA NTRS1990

The design and flight testing of a long endurance RPV

This paper covers the design process for a long endurance RPV. The 56-pound RPV must operate in the 25-60 knot speed range at low altitudes. An airfoil designed for low-Reynolds-number applications was used with a wing of aspect ratio 22 to reach an estimated L/D(max) of 25. Wing tip feathers were designed to reduce the induced drag. A comparison between the computed aerodynamic predictions and wind-tunnel results is given. The estimated endurance is on the order of 50 hours/gallon of fuel. A three-surface configuration was chosen, and the predicted handling quality and performance results obtained so far are given. The structural challenges in building a lightweight structure for the wing and control surfaces are outlined. The flight test program is currently underway.

Siddiqi, Shahid↗

NASA NTRS1991

F-15 composite engine access door

This paper presents a summary of the successfully concluded phase 1 of the two-phase Design and Manufacture of Advanced Thermoplastic Structures (DMATS) program. It addresses the design, manufacture, and validation testing of a thermoplastic F-15E forward engine access door and includes lessons learned during the concurrent product and process design development phases of the program.

Ramkumar, Ramaswamy L.↗

NASA NTRS1990

Space Station Freedom extravehicular activity systems evolution study

Evaluation of Space Station Freedom (SSF) support of manned exploration is in progress to identify SSF extravehicular activity (EVA) system evolution requirements and capabilities. The output from these studies will provide data to support the preliminary design process to ensure that Space Station EVA system requirements for future missions (including the transportation node) are adequately considered and reflected in the baseline design. The study considers SSF support of future missions and the EVA system baseline to determine adequacy of EVA requirements and capabilities and to identify additional requirements, capabilities, and necessary technology upgrades. The EVA demands levied by formal requirements and indicated by evolutionary mission scenarios are high for the out-years of Space Station Freedom. An EVA system designed to meet the baseline requirements can easily evolve to meet evolution demands with few exceptions. Results to date indicate that upgrades or modifications to the EVA system may be necessary to meet the full range of EVA thermal environments associated with the transportation node. Work continues to quantify the EVA capability in this regard. Evolution mission scenarios with EVA and ground unshielded nuclear propulsion engines are inconsistent with anthropomorphic EVA capabilities.

Rouen, Michael↗

NASA NTRS2001

Transition of a Three-Dimensional Unsteady Viscous Flow Analysis from a Research Environment to the Design Environment

The advent of advanced computer architectures and parallel computing have led to a revolutionary change in the design process for turbomachinery components. Two- and three-dimensional steady-state computational flow procedures are now routinely used in the early stages of design. Unsteady flow analyses, however, are just beginning to be incorporated into design systems. This paper outlines the transition of a three-dimensional unsteady viscous flow analysis from the research environment into the design environment. The test case used to demonstrate the analysis is the full turbine system (high-pressure turbine, inter-turbine duct and low-pressure turbine) from an advanced turboprop engine.

Dorney, Suzanne↗