Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “predictive simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Multi-axis Heterodyne Interferometry at MHz Frequencies: a Short-Arm Measurement Demonstration for LISA with Off-The-Shelf Hardware

We report the design, construction, and operation of a multi-axis heterodyne interferometry (MAHI) system operating at MHz heterodyne frequencies, which provides a testbed for technologies to be used in the Laser Interferometer Space Antenna (LISA) space-based gravitational wave mission. The system was calibrated for measurement of the piston, pitch, and yaw of a three-axis piezo-actuated mirror, giving measured calibration values that closely match those predicted by a simulation based on Gaussian beam tracing. The piston sensitivity of the MAHI system in the LISA band was measured to be below 10pmHz 1/2 10pmHz1/2 for frequencies above 4 mHz and below 1pmHz 1/2 1pmHz1/2 for frequencies above 35 mHz. The sensitivity is limited above 2 Hz by the mechanical vibrations of the apparatus and below 1 mHz by dimensional changes caused by temperature fluctuations. Evidence points towards scattered light as the limiting noise source at intermediate frequencies. The angular sensitivity of the MAHI system was measured to be close to or below 10nradHz 1/2 10nradHz1/2 for frequencies above 4 mHz and below 1nradHz 1/2 1nradHz1/2 for frequencies above 100 mHz. Noise budgets for both length and angle were determined, indicating the areas in which improvements must be made in order to reach increased sensitivity. The current operating sensitivity already provides a useful testbed for LISA technologies and a potential blueprint for future ground segment equipment.

Fulda, P.↗

TPSAS-NF1676L-15194-DND

Technical Motivation - 1950s: Indication of large lateral (roll/yaw) acceleration (“β-dot”) dynamic derivatives for configurations with strong vortex flows in the stall region (Lichtenstein, Campbell, Riley)! - 1960s: Increased emphasis on use of long-range missiles tempered by aircraft losses in close-in air combat - 1970s: - Effect of lateral acceleration derivatives on aircraft stability (Nguyen) - Characteristics and air combat advantages of rapid controlled large-amplitude maneuvering at low speeds near maximum lift shown in piloted simulations (Herbst) - 1980s: - Dynamic (forced-oscillation, rotary balance, curved- and rolling-flow) wind tunnel tests (Grafton, Lutze, Hultberg) - Incorporation of test data into computer simulations (Kalviste) - Technologies developed for controlled maneuvers at stall, post-stall angles of attack - Concern that conventional math modeling inadequately represented the dynamic component of these motions - Need to evaluate dependency of control laws on accurate computer simulations and motion prediction

Marilyn E Ogburn↗

Plume Impingement Studies in Space Environments for NASA Deep Space Logistics

NASA’s Artemis program is preparing to return Americans to the moon, in preparation for future deep space missions to Mars and beyond. The Lunar Gateway – a space station to be placed in orbit around the moon – serves as a critical component of the Artemis program, and will be the launchpad for future astronauts to visit the lunar surface and for humanity to learn how to live in a deep space environment. Much like the ISS, during operations and visiting vehicles approaches, the Lunar Gateway structures will be impinged upon from various plume sources: reaction control system rocket engine plumes, wastewater venting plumes, and plasma plumes from electric thrusters for station keeping. This presentation will describe the engineering challenges associated with each of these plume impingement scenarios and will detail the physical models and simulation approaches to predict the thermomechanical loading, contamination accretion, and erosion of station components due to plume impingement in space environments.

computational fluid dynamics↗

Plume Impingement Studies in Space Environments for NASA Deep Space Logistics

NASA’s Artemis program is preparing to return Americans to the moon, in preparation for future deep space missions to Mars and beyond. The Lunar Gateway – a space station to be placed in orbit around the moon – serves as a critical component of the Artemis program, and will be the launchpad for future astronauts to visit the lunar surface and for humanity to learn how to live in a deep space environment. Much like the ISS, during operations and visiting vehicles approaches, the Lunar Gateway structures will be impinged upon from various plume sources: reaction control system rocket engine plumes, wastewater venting plumes, and plasma plumes from electric thrusters for station keeping. This presentation will describe the engineering challenges associated with each of these plume impingement scenarios and will detail the physical models and simulation approaches to predict the thermomechanical loading, contamination accretion, and erosion of station components due to plume impingement in space environments.

Plume Impingement↗

Enhancing the Protection of Shielded Thermal Protection Systems in Sample Return Spacecraft Against MMOD Impact

Sample return missions seek to collect samples from planets, moons, asteroids, and other planetary bodies and return them to earth for in-depth analysis. Backward planetary protection requirements are often in place for such missions to prevent the introduction of any extra-terrestrial material into the Earth’s biosphere, which could occur if a meteoroid or space debris particle were to damage a critical part of the returning spacecraft. The ability of a shielding system used to mitigate this damage risk is typically characterized by a ballistic limit equation (BLE), which predicts whether or not a protected system or structural element will sustain a critical failure due to a high-speed impact. In this paper, we develop a particle-impact-based BLE for the thermal protection system (TPS) of a sample return spacecraft that is protected by a multi-shock shield. The predictions of the BLE we develop for TPS failure are shown to be consistent with the predictions of hydrocode simulations.

Sample Return Spacecraft↗

Direct simulation for the instability and breakup of laminar liquid jets

A direct numerical simulation method is described for predicting the deformation of laminar liquid jets. In the present nonlinear direct simulation, the convective term, which has been discarded in past linear analyses by Rayleigh and others, is included in the hydrodynamic equations. It is shown that only by maintaining full complexity of the nonlinear surface tension term accurate drop formation can be predicted. The continuity and momentum equations in the transient form are integrated on an adaptive grid, conforming the jet and surface wave shape. The equations, which are parabolic in time and elliptic in space, are solved by a TVD scheme with characteristic flux splitting. The results of the present work are discussed and compared with available measurements and other analyses. The comparison shows that among the predictions, the current 1-D direct simulation results agree best with the experimental data. Furthermore, the computer time requirements are much (an order of magnitude) smaller than those of previously reported multidimensional analyses.

Chuech, S. G.↗

Noise Prediction of Multi-stream Internally Mixed Jets with External and Internal Plugs using Large-Eddy Simulation

This paper presents results from ongoing research on jet noise prediction using wall-modeled large eddy simulations (WMLES) conducted within the Launch Ascent and Vehicle Aerodynamics (LAVA) computational framework. The study primarily focuses on the aeroacoustic implications of multi-stream nozzle configurations with internal mixing and both internal and external plugs, at a Reynolds number of 1×10 6 based on the nozzle exit diameter. While internal mixing nozzles have long been considered for jet noise reduction, the complexities of their impact on overall noise levels remain insufficiently understood. This research applies established best practices for WMLES to these complex nozzle configurations, aiming to assess their efficacy and identify limitations in accurately predicting noise behaviors. Through detailed comparisons with experimental data obtained from NASA’s Glenn Research Center, initial findings underscore the challenges inherent in current simulation practices when confronted with intricate geometric and operational conditions. Responding to these challenges, the study explores innovative computational approaches to rectify discrepancies noted between experimental outcomes and CFD predictions. Once example is the introduction of a resonating sound source in the simulation environment to mimic potential unobserved acoustic phenomena.A second example is the strategic modifications to the geometry of external plugs to account for real-world deformations caused by heating and gravity. These novel strategies aim to enhance the accuracy and reliability of noise predictions from supersonic jets, advancing our understanding and capability to effectively reduce jet noise in commercial supersonic aircraft

CST↗

Computer simulation for attitude disturbance torques for the Tiros-series.

Description of the Tiros-M Magnetic Attitude Prediction Program (TMMGAP), a simulation program designed to assist in the rotational motion control of the Tiros-series spacecraft. The subsystems of the program include input, attitude simulation, executive, attitude control and output components, simulating solar radiation pressure torque, gravity gradient torque, residual magnetic moment torque, and magnetic attitude control torques. The program provides data for prelaunch studies for launch window selection and mission planning, facilitates spacecraft spin axis reorientation after launch, provides spin axis control recommendations to meet mission constraints, and assists in the interpretation of cloud cover data. The program is characterized as effective in controlling spin axis and in processing picture data.

Sugai, I.↗

Characterization, performance, and prediction of a lead-acid battery under simulated electric vehicle driving requirements

A state-of-the-art 6-V battery module in current use by the electric vehicle industry was tested at the NASA Lewis Research Center to determine its performance characteristics under the SAE J227a driving schedules B, C, and D. The primary objective of the tests was to determine the effects of periods of recuperation and long and short periods of electrical regeneration in improving the performance of the battery module and hence extendng the vehicle range. A secondary objective was to formulate a computer program that would predict the performance of this battery module for the above driving schedules. The results show excellent correlation between the laboratory tests and predicted results. The predicted performance compared with laboratory tests was within +2.4 to -3.7 percent for the D schedule, +0.5 to -7.1 percent for the C schedule, and better than -11.4 percent for the B schedule.

Ewashinka, J. G.↗

Simulation of electron distributions within auroral acceleration regions

Plasma data from the Dynamics Explorer 1 satellite are used to investigate the electron distributions found within regions of parallel potential drops. A computer simulation was developed to predict major features of the observed electron distributions found within these regions. The simulation results are discussed and compared with observations. Good agreement is observed only when the potential distribution along the field line is split into separate potential drops, one above and one below the satellite. The simulated electron distribution exhibits a trapped particle region, the formation of the electron hole, and the evacuation of the loss cone.

Gurgiolo, C.↗

Evaluation of the hazard from exposure to electron irradiation simulating that in the synchronous orbit

The electron spectrum predicted for the synchronous orbit was simulated to determine the effects that might occur to astroscientists exposed to such irradiation while on a prolonged space station mission in that region. Miniature pigs were exposed to monoenergetic and spectral-fractionated irradiations with 0.5 to 2.1 MeV electrons. Clinical and pathological alterations observed in biopsies were correlated with depth-dose pattern and length of post irradiation period up to one year. With monoenergetic electrons, the lowest dose causing a recognizable lesion was 1450 rad and with increasing dose lesions appeared earlier and were more severe. At the highest dose given, 2650 rad, ulceration extending into the dermis was present by twenty one days and required about four months for complete healing. Spectral-fractionated irradiations, in which the total dose range was essentially comparable to that of the monoenergetic series, resulted in very minimal outer dermis edema at 1790 rad and at no dose employed did necrosis of epidermis or ulceration into dermis occur.

Lippincott, S. W.↗

Design of teleoperation system with a force-reflecting real-time simulator

We developed a force-reflecting teleoperation system that uses a real-time graphic simulator. This system eliminates the effects of communication time delays in remote robot manipulation. The simulator provides the operator with predictive display and feedback of computed contact forces through a six-degree of freedom (6-DOF) master arm on a real-time basis. With this system, peg-in-hole tasks involving round-trip communication time delays of up to a few seconds were performed at three support levels: a real image alone, a predictive display with a real image, and a real-time graphic simulator with computed-contact-force reflection and a predictive display. The experimental results indicate the best teleoperation efficiency was achieved by using the force-reflecting simulator with two images. The shortest work time, lowest sensor maximum, and a 100 percent success rate were obtained. These results demonstrate the effectiveness of simulated-force-reflecting teleoperation efficiency.

Hirata, Mitsunori↗

Maximum Likelihood Time-of-Arrival Estimation of Optical Pulses via Photon-Counting Photodetectors

Many optical imaging, ranging, and communications systems rely on the estimation of the arrival time of an optical pulse. Recently, such systems have been increasingly employing photon-counting photodetector technology, which changes the statistics of the observed photocurrent. This requires time-of-arrival estimators to be developed and their performances characterized. The statistics of the output of an ideal photodetector, which are well modeled as a Poisson point process, were considered. An analytical model was developed for the mean-square error of the maximum likelihood (ML) estimator, demonstrating two phenomena that cause deviations from the minimum achievable error at low signal power. An approximation was derived to the threshold at which the ML estimator essentially fails to provide better than a random guess of the pulse arrival time. Comparing the analytic model performance predictions to those obtained via simulations, it was verified that the model accurately predicts the ML performance over all regimes considered. There is little prior art that attempts to understand the fundamental limitations to time-of-arrival estimation from Poisson statistics. This work establishes both a simple mathematical description of the error behavior, and the associated physical processes that yield this behavior. Previous work on mean-square error characterization for ML estimators has predominantly focused on additive Gaussian noise. This work demonstrates that the discrete nature of the Poisson noise process leads to a distinctly different error behavior.

Erkmen, Baris I.↗

Prediction and Verification of Ductile Crack Growth from Simulated Defects in Strength Overmatched Butt Welds

Defects that develop in welds during the fabrication process are frequently manifested as embedded flaws from lack of fusion or lack of penetration. Fracture analyses of welded structures must be able to assess the effect of such defects on the structural integrity of weldments; however, the transferability of R-curves measured in laboratory specimens to defective structural welds has not been fully examined. In the current study, the fracture behavior of an overmatched butt weld containing a simulated buried, lack-of-penetration defect is studied. A specimen designed to simulate pressure vessel butt welds is considered; namely, a center crack panel specimen, of 1.25 inch by 1.25 inch cross section, loaded in tension. The stress-relieved double-V weld has a yield strength 50% higher than that of the plate material, and displays upper shelf fracture behavior at room temperature. Specimens are precracked, loaded monotonically while load-CMOD measurements are made, then stopped and heat tinted to mark the extent of ductile crack growth. These measurements are compared to predictions made using finite element analysis of the specimens using the fracture mechanics code Warp3D, which models void growth using the Gurson-Tvergaard dilitant plasticity formulation within fixed sized computational cells ahead of the crack front. Calibrating data for the finite element analyses, namely cell size and initial material porosities are obtained by matching computational predictions to experimental results from tests of welded compact tension specimens. The R-curves measured in compact tension specimens are compared to those obtained from multi-specimen weld tests, and conclusions as to the transferability of R-curves is discussed.

Nishioka, Owen S.↗

Jet Noise Prediction Using Hybrid RANS/LES with Structured Overset Grids

Hybrid RANS/LES simulations using the structured overset grid approach and a low dissipation finite-difference method within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework are presented for jet noise prediction. The simulations are part of a validation effort to demonstrate jet noise prediction capability, to assess noise characteristics of next generation quiet supersonic commercial jets. Results are compared with experimental data acquired in the Small Hot Jet Acoustic Rig in the Aeroacoustic Propulsion Laboratory at NASA Glenn Research Center. Details of the structured overset grids, numerical discretization, and turbulence model are provided. Near-field comparisons to PIV data and far-field comparisons to microphone data are discussed. Excellent agreement of time-averaged mean quantities along the jet center-line and lip-line are obtained. Good agreement with root-mean-squared (RMS) quantities along the jet center-line are also obtained. An over prediction of lip-line RMS at the nozzle exit is observed leading to a small over-prediction of side-line far-field noise (less than 2 dB). Good agreement with far-field noise in the Mach wave radiation directions is achieved.

Housman, Jeffrey A.↗

Simulated rarefied aerodynamics of the Magellan spacecraft during aerobraking

Aerodynamic loads upon the Magellan spacecraft during aerobraking through the atmosphere of Venus are computed at off-design attitudes with a direct simulation Monte Carlo (DSMC) particle method. Simulated rarefied flows at nominal altitudes near 140 km and an entry speed of 8.6 km/s were compared to simulated and analytic free molecular results. Aerodynamic moments, forces, and heating for rarefied entry at all attitudes were 7-10 percent below free molecular results. All moments acted to restore the vehicle to its nominal zero-pitch, zero-yaw attitude. Suggested canting of the solar panels is an innovative configuration to assess gas-surface interaction during aerobraking. The resulting roll torques about the central body-axis as predicted in rarefied flow simulations were nearly twice that predicted for free molecular flow, although differences became less distinct for thermal accommodation coefficients well below unity. Roll torques increased dramatically with reduced accommodation coefficients employed in the simulation. In the DSMC code, periodic free-molecule boundary conditions and a coarse computational grid and body resolution served to minimize the simulation size and cost while retaining solution validity.

Haas, Brian L.↗

Noise of Embedded High Aspect Ratio Nozzles

A family of high aspect ratio nozzles were designed to provide a parametric database of canonical embedded propulsion concepts. Nozzle throat geometries with aspect ratios of 2:1, 4:1, and 8:1 were chosen, all with convergent nozzle areas. The transition from the typical round duct to the rectangular nozzle was designed very carefully to produce a flow at the nozzle exit that was uniform and free from swirl. Once the basic rectangular nozzles were designed, external features common to embedded propulsion systems were added: extended lower lip (a.k.a. bevel, aft deck), differing sidewalls, and chevrons. For the latter detailed Reynolds-averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) simulations were made to predict the thrust performance and to optimize parameters such as bevel length, and chevron penetration and azimuthal curvature. Seventeen of these nozzles were fabricated at a scale providing a 2.13 inch diameter equivalent area throat." ! The seventeen nozzles were tested for far-field noise and a few data were presented here on the effect of aspect ratio, bevel length, and chevron count and penetration. The sound field of the 2:1 aspect ratio rectangular jet was very nearly axisymmetric, but the 4:1 and 8:1 were not, the noise on their minor axes being louder than the major axes. Adding bevel length increased the noise of these nozzles, especially on their minor axes, both toward the long and short sides of the beveled nozzle. Chevrons were only added to the 2:1 rectangular jet. Adding 4 chevrons per wide side produced some decrease at aft angles, but increased the high frequency noise at right angles to the jet flow. This trend increased with increasing chevron penetration. Doubling the number of chevrons while maintaining their penetration decreased these effects. Empirical models of the parametric effect of these nozzles were constructed and quantify the trends stated above." Because it is the objective of the Supersonics Project that future design work be done more by physics-based computations and less by experiments, several codes under development were evaluated against these test cases. Preliminary results show that the RANS-based code JeNo predicts the spectral directivity of the low aspect ratio jets well, but has no capability to predict the non-axisymmetry. An effort to address this limitations, used in the RANS-based code of Leib and Goldstein, overpredicted the impact of aspect ratio. The broadband shock noise code RISN, also limited to axisymmetric assumptions, did a good job of predicting the spectral directivity of underexpanded 2:1 cold jet case but was not as successful on high aspect ratio jets, particularly when they are hot. All results are preliminary because the underlying CFD has not been validated yet. An effort using a Large Eddy Simulation code by Stanford University predicted noise that agreed with experiments to within a few dB.

Bridges, James E.↗

Interlaminar R-Curve Effects in Thermoplastic Composites: Experiments and Model Correlations

The interlaminar fracture behavior of thermoplastic composites under Mode-I and Mode-II static loading is investigated in this research. The material system under consideration is a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK)†. Characterization experiments were conducted to measure the load-displacement response, peak load, and propagation of delamination from a pre-implanted Kapton® insert. The Mode-I response was characterized using a double cantilever beam (DCB) test according to the ASTM D5528-22 standard. It was observed that the propagation exhibited significant resistance to delamination growth, i.e., an R-Curve effect. The test data indicated that the steady-state fracture toughness, G SS I , was approximately twice the mean initiation fracture toughness, G Ic . The Mode-II response of an end notch flexure (ENF) specimen tested according to the ASTM D7905-19 standard exhibited an unexpected stable behavior upon attaining peak load. Prior to attaining peak load, the Mode-II response exhibited some non-linearity, which may be attributed to nonlinear bulk material response, e.g., hyper-elasticity, viscoelasticity, plasticity, etc., and potentially friction at the load/support rollers and R-Curve effects. Finite element models based on the Cohesive Zone Method (CZM) and the Virtual Crack Closure Technique (VCCT) were used to predict the DCB and ENF specimen responses. DCB analysis results obtained using G SS I predicted propagation consistent with experimental data. However, results obtained with the as characterized G Ic were inaccurate in predicting delamination growth onset and peak load. ENF analysis results obtained with the as-characterized Mode-II fracture toughness, G IIc , were inaccurate in predicting the peak load and propagation. Hence, R-Curve effects were included in both DCB and ENF simulations, which enabled improved predictions. The experimentally determined Mode-I R-Curve was used for the DCB simulations, whereas an R-Curve was derived for Mode-II assuming that the change in compliance of the specimen was associated with crack growth only.

Prabhakar M Rao↗