Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase variation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Integral Twist Actuation of Helicopter Rotor Blades for Vibration Reduction

Active integral twist control for vibration reduction of helicopter rotors during forward flight is investigated. The twist deformation is obtained using embedded anisotropic piezocomposite actuators. An analytical framework is developed to examine integrally-twisted blades and their aeroelastic response during different flight conditions: frequency domain analysis for hover, and time domain analysis for forward flight. Both stem from the same three-dimensional electroelastic beam formulation with geometrical-exactness, and axe coupled with a finite-state dynamic inflow aerodynamics model. A prototype Active Twist Rotor blade was designed with this framework using Active Fiber Composites as the actuator. The ATR prototype blade was successfully tested under non-rotating conditions. Hover testing was conducted to evaluate structural integrity and dynamic response. In both conditions, a very good correlation was obtained against the analysis. Finally, a four-bladed ATR system is built and tested to demonstrate its concept in forward flight. This experiment was conducted at NASA Langley T~ansonic Dynamics Tunnel and represents the first-of-a-kind Mach-scaled fully-active-twist rotor system to undergo forward flight test. In parallel, the impact upon the fixed- and rotating-system loads is estimated by the analysis. While discrepancies are found in the amplitude of the loads under actuation, the predicted trend of load variation with respect to its control phase correlates well. It was also shown, both experimentally and numerically, that the ATR blade design has the potential for hub vibratory load reduction of up to 90% using individual blade control actuation. Using the numerical framework, system identification is performed to estimate the harmonic transfer functions. The linear time-periodic system can be represented by a linear time-invariant system under the three modes of blade actuation: collective, longitudinal cyclic, and lateral cyclic. A vibration minimizing controller is designed based on this result, which implements classical disturbance rejection algorithm with some modifications. The controller is simulated numerically, and more than 90% of the 4P hub vibratory load is eliminated. By accomplishing the experimental and analytical steps described in this thesis, the present concept is found to be a viable candidate for future generation low-vibration helicopters. Also, the analytical framework is shown to be very appropriate for exploring active blade designs, aeroelastic behavior prediction, and as simulation tool for closed-loop controllers.

Shin, SangJoon↗
NASA NTRS2004

Magnesium Isotopes in the Earth, Moon, Mars, and Pallasite Parent Body: High-Precision Analysis of Olivine by Laser-Ablation Multi-Collector ICPMS

Magnesium isotopes potentially offer new insights into a diverse range of processes including evaporation and condensation in the solar nebula, melting and metasomatism in planetary interiors, and hydrothermal alteration [1,2,3,4]. Volatility-related Mg isotopic variations of up to 10 per mil/amu relative to a terrestrial standard have been found in early nebular phases interpreted as evaporation residues [1], and relatively large variations (up to 3 per mil/amu) in the terrestrial mantle have been reported recently [4]. In order to investigate possible differences in the nebular history of material contributing to the terrestrial planets, and to search for evidence of a high-temperature origin of the Moon, we have measured the magnesium isotopic composition of primitive olivines from the Earth, Moon, Mars, and pallasite parent body using laser-ablation multicollector ICPMS.

Norman, M.↗
NASA NTRS1998

Stochastic feedback and the regulation of biological rhythms

We propose a general approach to the question of how biological rhythms spontaneously self-regulate, based on the concept of "stochastic feedback". We illustrate this approach by considering at a coarse-grained level the neuroautonomic regulation of the heart rate. The model generates complex dynamics and successfully acounts for key characteristics of cardiac variability, including the l/f power spectrum, the functional form and scaling of the distribution of variations, and correlations in the Fourier phases indicating nonlinear dynamics.

NASA Discipline Cardiopulmonary↗
NASA NTRS2005

The Cycle of Cosmic Dust

The presence of dust in the interstellar medium of galaxies dramatically affects their spectral appearance, and the interpretation of their underlying physical properties. Consequently, the diagnostic of galaxy spectra depends crucially on our understanding of the nature and properties of these dust particles. Models of interstellar dust particles must be able to reproduce a basic set of observational constraints, including the general interstellar extinction and infrared emission observed in the diffuse interstellar medium (ISM). Recent analysis of the solar spectrum have resulted in a convergence between the solar and B star abundances. This development, and the steadiness in the solar abundance determination of the primary refractory elements Mg, Si, and Fe, strongly suggest that any viable dust model must also obey interstellar abundances constraints. I will present fifteen dust models that differ in composition and size distribution and that simultaneously satisfy the local extinction, infrared emission, and abundances constraints have been shown to exist. This multitude of viable dust models provides us with an increased flexibility in understanding dust evolution and the many variations in dust properties in different phases of the ISM and stellar environments.

Dwek, Eliahu↗
NASA NTRS2007

Calculation of Hub Loads at Low Airspeeds with Active Control

The effect of individual blade control (IBC) on the full-scale, low airspeed, level flight UH-60A oscillatory fixed system 4P hub loads and the rotating system blade bending moments is studied. The effect of a single 3P IBC input has been considered in this analytical study. At the low speed under consideration, it has been found that convergence of the comprehensive analysis is important for obtaining good predictions. Good correlation has been obtained with the measured full-scale wind tunnel data for the shapes of the fixed system 4P hub loads variations with the 3P IBC input phase, and also for the "best" phase of the 3P input (for minimum hub loads). The blade bending moment comparison shows mixed results. The 3P lead lag and the 4P flap bending moment trends with the 3P IBC input phase are reasonably predicted, whereas the 5P lead lag bending moment trend is not predicted well. Finally, the prediction of the baseline (no IBC) bending moments needs further study.

Kottapalli, Sesi↗
NASA NTRS2006

Snap-Through of Unsymmetric Laminates Using Piezocomposite Actuators

The paper discusses the concept of using a piezoceramic actuator bonded to one side of a two-layer unsymmetric cross-ply [0/90]T laminate to provide the moments necessary to snap the laminate from one stable equilibrium shape to another. This concept could be applied to the morphing of structures. A model of this concept, which is based on the Rayleigh-Ritz technique and the use of energy and variational methods, is developed. The experimental phase of the study is discussed, including the measurement of the voltage level needed to snap the laminate. The voltage measurements and shapes are compared with predictions of the models and the agreement between measurements and the predictions are reasonable, both qualitatively and quantitatively. Suggestions for future activities are presented.

Schultz, Marc R.↗
NASA NTRS2010

Observed Seasonal to Decadal-Scale Responses in Mesospheric Water Vapor

The 14-yr (1991-2005) time series of mesospheric water vapor from the Halogen Occultation Experiment (HALOE) are analyzed using multiple linear regression (MLR) techniques for their6 seasonal and longer-period terms from 45S to 45N. The distribution of annual average water vapor shows a decrease from a maximum of 6.5 ppmv at 0.2 hPa to about 3.2 ppmv at 0.01 hPa, in accord with the effects of the photolysis of water vapor due to the Lyman-flux. The distribution of the semi-annual cycle amplitudes is nearly hemispherically symmetric at the low latitudes, while that of the annual cycles show larger amplitudes in the northern hemisphere. The diagnosed 11-yr, or solar cycle, max minus min, water vapor values are of the order of several percent at 0.2 hPa to about 23% at 0.01 hPa. The solar cycle terms have larger values in the northern than in the southern hemisphere, particularly in the middle mesosphere, and the associated linear trend terms are anomalously large in the same region. Those anomalies are due, at least in part, to the fact that the amplitudes of the seasonal cycles were varying at northern mid latitudes during 1991-2005, while the corresponding seasonal terms of the MLR model do not allow for that possibility. Although the 11-yr variation in water vapor is essentially hemispherically-symmetric and anti-phased with the solar cycle flux near 0.01 hPa, the concurrent temperature variations produce slightly colder conditions at the northern high latitudes at solar minimum. It is concluded that this temperature difference is most likely the reason for the greater occurrence of polar mesospheric clouds at the northern versus the southern high latitudes at solar minimum during the HALOE time period.

Remsberg, Ellis↗
NASA NTRS2013

Testing the Origins of Basalt Fragments fro Apollo 16

Several 2-4 mm regolith fragments of basalt from the Apollo 16 site were recently described by [1]. These included a high-Ti vitrophyric basalts (60603,10-16) and one very-low-titanium (VLT) crystalline basalt (65703,9-13). As Apollo 16 was the only highlands sample return mission distant from the maria, identification of basaltic samples at the site indicates input from remote sites via impact processes [1]. However, distinguishing between impact melt and pristine basalt can be notoriously difficult and requires significant sample material [2-6]. The crystal stratigraphy method utilizes essentially non-destructive methods to make these distinctions [7,8]. Crystal stratigraphy combines quantitative petrography in the form of crystal size distributions (CSDs) coupled with mineral geochemistry to reveal the petrogenetic history of samples. The classic CSD plot of crystal size versus population density can reveal insights on growth/cooling rates, residence times, and magma history which in turn can be used to evaluate basaltic vs impact melt origin [7-9]. Electron microprobe (EMP) and laser ablation (LA)-ICP-MS analyses of mineral phases complement textural investigations. Trace element variations document subtle changes occurring during the formation of the samples, and are key in the interpretation and preservation of this rare lunar sample collection.

Donohue, P. H.↗
NASA NTRS2014

Configuration and Assessment of the GISS ModelE2 Contributions to the CMIP5 Archive

We present a description of the ModelE2 version of the Goddard Institute for Space Studies (GISS) General Circulation Model (GCM) and the configurations used in the simulations performed for the Coupled Model Intercomparison Project Phase 5 (CMIP5). We use six variations related to the treatment of the atmospheric composition, the calculation of aerosol indirect effects, and ocean model component. Specifically, we test the difference between atmospheric models that have noninteractive composition, where radiatively important aerosols and ozone are prescribed from precomputed decadal averages, and interactive versions where atmospheric chemistry and aerosols are calculated given decadally varying emissions. The impact of the first aerosol indirect effect on clouds is either specified using a simple tuning, or parameterized using a cloud microphysics scheme. We also use two dynamic ocean components: the Russell and HYbrid Coordinate Ocean Model (HYCOM) which differ significantly in their basic formulations and grid. Results are presented for the climatological means over the satellite era (1980-2004) taken from transient simulations starting from the preindustrial (1850) driven by estimates of appropriate forcings over the 20th Century. Differences in base climate and variability related to the choice of ocean model are large, indicating an important structural uncertainty. The impact of interactive atmospheric composition on the climatology is relatively small except in regions such as the lower stratosphere, where ozone plays an important role, and the tropics, where aerosol changes affect the hydrological cycle and cloud cover. While key improvements over previous versions of the model are evident, these are not uniform across all metrics.

ocean model↗
NASA NTRS2009

Power Sources for Micro-Autonomous Vehicles- Challenges and Prospects

Micro-autonomous vehicle systems are expected to have expanded role in military missions by providing full spectrum intelligence, surveillance and reconnaissance support on the battlefield, suppression of enemy defenses, and enabling co-operative (swarm-like) configurations. Of the numerous demanding requirements of autonomy, sensing, navigation, mobility, etc., meeting the requirement of mission duration or endurance is a very challenging one. This requirement is demanding because of the constraints of mass and volume that limit the quantity of energy that can be stored on-board. Energy is required for mobility, payload operation, information processing, and communication. Mobility requirements typically place an extraordinary demand on the specific energy (Wh/kg) and specific power (W/kg) of the power source; the actual distribution of the energy between mobility and other system functions could vary substantially with the mission type. The power requirements for continuous mobility can vary from 100-1000 W/kg depending on the terrain, ground speed and flight speed. Even with the power source accounting for 30% of the mass of the vehicle, the best of rechargeable batteries can provide only up to 1-2 hours of run-time for a continuous power demand at 100W/kg. In the case of micro-aerial vehicles with flight speed requirements in the range of 5-15 m s-1, the mission times rarely exceed 20 minutes [2]. Further, the power required during take-off and hover can be twice or thrice that needed for steady level flight, and thus the number and sequence of such events is also limited by the mass and size of the power source. For operations such as "perch and stare" or "silent watch" the power demand is often only a tenth of that required during continuous flight. Thus, variation in power demand during various phases of the mission importantly affects the power source selection.

fuel cells↗
DOE OSTI2020

Achieving balanced execution through runtime detection of performance variation

Systems, apparatuses, and methods for achieving balanced execution in a multi-node cluster through runtime detection of performance variation are described. During a training phase, performance counters and an amount of time spent waiting for synchronization is monitored for a plurality of tasks for each node of the multi-node cluster. These values are utilized to generate a model which correlates the values of the performance counters to the amount of time spent waiting for synchronization. Once the model is built, the values of the performance counters are monitored for a period of time at the start of each task, and these values are input into the model. The model generates a prediction of whether a given node is on the critical path. If the given node is predicted to be on the critical path, the power allocation of the given node is increased.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

TensorFlow Quantum: A Software Framework for Quantum Machine Learning

We introduce TensorFlow Quantum (TFQ), an open source library for the rapid prototyping of hybrid quantum-classical models for classical or quantum data. This framework offers high-level abstractions for the design and training of both discriminative and generative quantum models under TensorFlow and supports high-performance quantum circuit simulators. We provide an overview of the software architecture and building blocks through several examples and review the theory of hybrid quantum-classical neural networks. We illustrate TFQ functionalities via several basic applications including supervised learning for quantum classification, quantum control, simulating noisy quantum circuits, and quantum approximate optimization. Moreover, we demonstrate how one can apply TFQ to tackle advanced quantum learning tasks including meta-learning, layerwise learning, Hamiltonian learning, sampling thermal states, variational quantum eigensolvers, classification of quantum phase transitions, generative adversarial networks, and reinforcement learning. We hope this framework provides the necessary tools for the quantum computing and machine learning research communities to explore models of both natural and artificial quantum systems, and ultimately discover new quantum algorithms which could potentially yield a quantum advantage.

Broughton, Michael↗
DOE OSTI2021

Cluster Variation Method Analysis of Correlations and Entropy in BCC Solid Solutions

Solid solutions occur when multiple chemical species share sites of a common crystal lattice. Although the single site occupation is random, chemical interaction preferences bias the occupation probabilities of neighboring sites, and this bias reduced the entropy of mixing below its ideal value. Sufficiently strong bias leads to symmetry-breaking phase transitions. Here, we apply the cluster variation method to explore solid solutions on body centered cubic lattices in the context of two specific compounds that exhibit opposite ordering trends. Employing density functional theory to model the energetics, we show that CuZn exhibits an order-disorder transition to the CsCl prototype structure, while AlLi instead takes the NaTl prototype structure, and we evaluate their temperature-dependent order parameters, correlations and entropies.

36 MATERIALS SCIENCE↗
NASA NTRS2005

Wavefront Amplitude Variation of TPF's High Contrast Imaging Testbed: Modeling and Experiment

Knowledge of wavefront amplitude is as important as the knowledge of phase for a coronagraphic high contrast imaging system. Efforts have been made to understand various contributions of the amplitude variation in Terrestrial Planet Finder's (TPF) High Contrast Imaging Testbed (HCIT). Modeling of HCIT with as-built mirror surfaces has shown an amplitude variation of 1.3% due to the phase-amplitude mixing for the testbed's front-end optics. Experimental measurements on the testbed have shown the amplitude variation is about 2.5% with the testbed's illumination pattern has a major contribution as the low order amplitude variation.

coronagraph↗
NASA NTRS1995

Dissecting the EUV spectrum of Capella

Extreme ultraviolet spectra of Capella, obtained at various orbital phases over the past two years by the EUVE satellite, show strong emission lines from a continuous distribution of temperatures (approximately 10(exp 5 -10(exp 7.3) K). In addition to the strong He II lambda 303.8, the spectra are dominated by emission lines of highly ionized iron. Strong lines of Fe IX, XV, XVI, and XVIII-XXIV are used to construct emission measure distributions for the individual pointings, which show several striking features, including a minimum near 10(exp 6) K and a local maximum at 10(exp 6.8) K. Furthermore, intensities of the highest temperature lines (Te is greater than 10(exp 7) K) show variations (factors of 2-3) at different orbital phases, while the lower temperature Fe lines show variations of about 30% or less. The low variability of most of the strong low temperature features motivates a detailed analysis of the summed spectrum. With approximately 280 ksec of total exposure time, we have measured over 200 emission features with S/N greater than or equal to 3.0 in the summed spectrum. We report here initial results from the analysis of this spectrum. We can now identify lines of Fe VIII and X-XIV, as well as a number of electron density and abundance diagnostic lines. We also report here the first direct measurement of the continuum flux around approximately 100 A in a cool star atmosphere with EUVE. The continuum flux can be predicted from the emission measure model based on Fe line emission, and demonstrates that the Fe/H abundance ratio is dose to the solar photospheric value.

Brickhouse, Nancy S.↗
NASA NTRS1999

Thin Film Ba(x)Sr(1-x)TiO3 Ku- and K-Band Phase Shifters Grown on MgO Substrates

We report measurements of gold circuits fabricated on four Ba(x)Sr(1-x)TiO3 films doped with 1% Mn grown on MgO substrates by laser ablation. Low frequency measurements of epsilon(sub r) and tan(delta) on interdigital capacitors are compared with high frequency measurements of phase shift and insertion loss on coupled microstrip phase shifters done on the same films. The variation in temperature of both high and low frequency device parameters is compared. Annealed and unannealed films are compared. Room temperature figures of merit of phase shift per insertion loss of up to 58.4 C/dB at 18 GHz and 400 V dc bias were measured.

VanKeuls, F. W.↗
NASA NTRS1995

Chromospheric variations in main-sequence stars

The fluxes in passbands 0.1 nm wide and centered on the Ca II H and K emission cores have been monitored in 111 stars of spectral type F2-M2 on or near the main sequence in a continuation of an observing program started by O. C. Wilson. Most of the measurements began in 1966, with observations scheduled monthly until 1980, when observations were schedueld sevral times per week. The records, with a long-term precision of about 1.5%, display fluctuations that can be idntified with variations on timescales similar to the 11 yr cycle of solar activity as well as axial rotation, and the growth and decay of emitting regions. We present the records of chromospheric emission and general conclusions about variations in surface magnetic activity on timescales greater than 1 yr but less than a few decades. The results for stars of spectral type G0-K5 V indicate a pattern of change in rotation and chromospheric activity on an evolutionary timescale, in which (1) young stars exhibit high average levels of activity, rapid rotation rates, no Maunder minimum phase and rarely display a smooth, cyclic variation; (2) stars of intermediate age (approximately 1-2 Gyr for 1 solar mass) have moderate levels of activity and rotation rates, and occasional smooth cycles; and (3) stars as old as the Sun and older have slower rotation rates, lower activity levels and smooth cycles with occasional Maunder minimum-phases.

Baliunas, S. L.↗