Results for “parameter compression” — Page 44

NASA NTRS1983

SEASAT observations of lithospheric flexure seaward of trenches

Lithospheric flexure seaward of deep ocean trenches in SEASAT altimeter observations of the marine geoid. In fact, mechanical models of lithospheric flexure can be tested directly on the SEASAT altimeter data. A simple elastic model was used for the oceanic lithosphere and, after least squares adjustments, estimates of model parameters were recovered including Outer Rise (OR) amplitude, OR wavelength, and effective lithospheric thickness. Effective lithospheric thickness was recovered for five regions: the Mariana, the Kuril, the Philippine, the Aleutian and the Middle America OR. These results support the suggestion of Bodine et al. (1981) that effective thickness, T, increased with age of lithosphere in approximate accord with the relation T approximately equals x age to the 1/2 power where C approximately equals 4 km x my to the -1/2 power. Altimetric results agree more closely with this relation than do published results based on bathymetric data. The close agreement with the thickness-age relation suggests that there is no longer any need to assume that significant horizontal compression acts across the Kuril, Marianas and Izo-Bonin trenches. This thickness-age relation implies that flexural strength of the oceanic lithosphere is temperature controlled.

Mcadoo, D. C.↗

NASA NTRS1991

Improved compression molding technology for continuous fiber reinforced composite laminates. Part 2: AS-4/Polyimidesulfone prepreg system

AS-4/polyimidesulfone (PISO2) composite prepreg was utilized for the improved compression molding technology investigation. This improved technique employed molding stops which advantageously facilitate the escape of volatile by-products during the B-stage curing step, and effectively minimize the neutralization of the consolidating pressure by intimate interply fiber-fiber contact within the laminate in the subsequent molding cycle. Without the modifying the resin matrix properties, composite panels with both unidirectional and angled plies with outstanding C-scans and mechanical properties were successfully molded using moderate molding conditions, i.e., 660 F and 500 psi, using this technique. The size of the panels molded were up to 6.00 x 6.00 x 0.07 in. A consolidation theory was proposed for the understanding and advancement of the processing science. Processing parameters such as vacuum, pressure cycle design, prepreg quality, etc. were explored.

Baucom, Robert M.↗

NASA NTRS1950

Two-dimensional compressible flow in centrifugal compressors with straight blades

Six numerical examples are presented for steady, two-dimensional, compressible, nonviscous flow in centrifugal compressors with thin straight blades, the center lines of which generate the surface of a right circular cone when rotated about the axis of the compressor. A seventh example is presented for incompressible flow. The solutions were obtained in a region of the compressors, including the impeller tip, that was considered to be unaffected by the diffuser vanes or by the impeller-inlet configuration. Each solution applies to radial and mixed flow compressors with various cone angles but with the same angle between blades on the conic flow surface. The solution also apply to radial and mixed flow turbines with the rotation and the flow direction reversed. The effects of variations in the following parameters were investigated: (1) flow rate, (2) impeller-tip speed, (3) variation of passage height with radius, and (4) angle between blades on conic flow surface. The numerical results are presented in plots of the streamlines and constant Mach number lines. Correlation equations are developed whereby the flow conditions in any impeller with straight blades can be determined (in the region investigated by this analysis) for all operating conditions.

Stanitz, John D↗

NASA NTRS1997

Planetary and Primitive Object Strength Measurements and Sampling Apparatus

We present experimental data and a model for the low-velocity (subsonic, 0 - 1000 m/s) penetration of brittle materials by both solid and hollow (i.e., coring) penetrators. The experiments show that penetration is proportional to momentum/frontal area of the penetrator. Because of the buildup of a cap in front of blunt penetrators, the presence or absence of a streamlined or sharp front end usually has a negligible effect for impact into targets with strength. The model accurately predicts the dependence of penetration depth on the various parameters of the target-penetrator system, as well as the qualitative condition of the target material ingested by a corer. In particular, penetration depth is approximately inversely proportional to the static bearing strength of the target. The bulk density of the target material has only a small effect on penetration, whereas friction can be significant, especially at higher impact velocities, for consolidated materials. This trend is reversed for impacts into unconsolidated materials. The present results suggest that the depth of penetration is a good measure of the strength, but not the density, of a consolidated target. Both experiments and model results show that, if passage through the mouth of a coring penetrator requires initially porous target material to be compressed to less than 26% porosity, the sample collected by the corer will be highly fragmented. If the final porosity remains above 26%, then most materials, except cohesionless materials, such as dry sand, will be collected as a compressed slug of material.

Ahrens, Thomas J.↗

NASA NTRS2005

EUV Imaging of SWCX-Produced He(+) 30.4-nm Emission/Scattering at the Magnetosheath

Theoretically, charge exchange between solar wind alpha-particles and geocoronal hydrogen at the magnetosheath results in the production of helium ions in an excited state, i.e, He(2+) + H (right arrow) He(+*) + H(+) resulting in the emission of 30.4-nm radiation upon relaxation of the helium ions. It has been estimated that the magnetosphere was compressed to inside the orbit of IMAGE during the Halloween storm of 2003. This configuration should have placed the subsolar point of the magnetosheath well beyond the limb of the solar disk and allow EUV the potential of imaging this solar wind charge exchange interaction Analysis of EUV full-frame data acquired during 31 October 2003 (Day 304) indicates the detection of 30.4-nm photons in the likely vicinity of the magnetosheath either as a direct consequence of the emission proposed above or, provided the magnetosheath He(+) density was sufficient to exceed the EUV sensitivity threshold, via resonant scattering of solar UV. We present initial analysis of EUV imaging during the Halloween 2003 storm from the context of solar wind parameters, including composition, and from the perspective of the generation of simulated EUV imaging of the event both as an emitting and as a scattering process.

Adrian, M. L.↗

NASA NTRS2001

Computational Analysis of a Pylon-Chevron Core Nozzle Interaction

In typical engine installations, the pylon of an engine creates a flow disturbance that interacts with the engine exhaust flow. This interaction of the pylon with the exhaust flow from a dual stream nozzle was studied computationally. The dual stream nozzle simulates an engine with a bypass ratio of five. A total of five configurations were simulated all at the take-off operating point. All computations were performed using the structured PAB3D code which solves the steady, compressible, Reynolds-averaged Navier-Stokes equations. These configurations included a core nozzle with eight chevron noise reduction devices built into the nozzle trailing edge. Baseline cases had no chevron devices and were run with a pylon and without a pylon. Cases with the chevron were also studied with and without the pylon. Another case was run with the chevron rotated relative to the pylon. The fan nozzle did not have chevron devices attached. Solutions showed that the effect of the pylon is to distort the round Jet plume and to destroy the symmetrical lobed pattern created by the core chevrons. Several overall flow field quantities were calculated that might be used in extensions of this work to find flow field parameters that correlate with changes in noise.

Thomas, Russell H.↗

NASA NTRS1945

Completed Tabulation in the United States of Tests of 24 Airfoils at High Mach Numbers (Derived from Interrupted Work at Guidonia, Italy in the 1.31- by 1.74-Foot High-Speed Tunnel)

Two-dimensional data were obtained in Mach range of from 0.40 to 0.94 and Reynolds Number range of (3.4 - 4.2) X 10 Degrees. Results indicate that thickness ratio is dominating shape parameter at high Mach numbers and that aerodynamic advantages are attainable by using thinnest possible sections. Effects of jet boundaries, Reynolds Number, and Data presented are free from jet-boundary and humidity effects.

AIR FLOW VELOCITY, HIGH - SUBSONIC↗

NASA NTRS2010

Hybrid Reynolds-Averaged/Large-Eddy Simulations of a Coaxial Supersonic Free-Jet Experiment

Reynolds-averaged and hybrid Reynolds-averaged/large-eddy simulations have been applied to a supersonic coaxial jet flow experiment. The experiment was designed to study compressible mixing flow phenomenon under conditions that are representative of those encountered in scramjet combustors. The experiment utilized either helium or argon as the inner jet nozzle fluid, and the outer jet nozzle fluid consisted of laboratory air. The inner and outer nozzles were designed and operated to produce nearly pressure-matched Mach 1.8 flow conditions at the jet exit. The purpose of the computational effort was to assess the state-of-the-art for each modeling approach, and to use the hybrid Reynolds-averaged/large-eddy simulations to gather insight into the deficiencies of the Reynolds-averaged closure models. The Reynolds-averaged simulations displayed a strong sensitivity to choice of turbulent Schmidt number. The initial value chosen for this parameter resulted in an over-prediction of the mixing layer spreading rate for the helium case, but the opposite trend was observed when argon was used as the injectant. A larger turbulent Schmidt number greatly improved the comparison of the results with measurements for the helium simulations, but variations in the Schmidt number did not improve the argon comparisons. The hybrid Reynolds-averaged/large-eddy simulations also over-predicted the mixing layer spreading rate for the helium case, while under-predicting the rate of mixing when argon was used as the injectant. The primary reason conjectured for the discrepancy between the hybrid simulation results and the measurements centered around issues related to the transition from a Reynolds-averaged state to one with resolved turbulent content. Improvements to the inflow conditions were suggested as a remedy to this dilemma. Second-order turbulence statistics were also compared to their modeled Reynolds-averaged counterparts to evaluate the effectiveness of common turbulence closure assumptions.

Baurle, Robert A.↗

NASA NTRSDate not supplied

Fabrication and Mechanical Testing of Heat Exchanger Tubes for Nuclear Propulsion and Other Applications from Continuous Carbon Nanotube Yarns and Tapes

As NASA and other agencies are looking to conduct sustained operations in space, nuclear engines have been receiving increased focus. The high specific impulse and high fuel efficiency at high thrust output of these engines can halve the transit time for human missions to Mars, or enable missions requiring multiple orbital parameter adjustments. In both Nuclear Thermal Propulsion (NTP) and Nuclear Electric Propulsion (NEP) systems, heat exchangers play a critical role in transferring energy from the reactor to a working fluid, hydrogen in the case of NTP and a molten salt or other fluid for electricity generation in NEP. Heat exchangers are also required in other parts of the spacecraft. Various manufacturing methods and materials are being considered for the heat exchangers. In this presentation the fabrication and testing of heat exchangers made from continuous carbon nanotube (CNT) yarns and tapes are discussed. The fabrication workflow is compared and contrasted, as well as performance of prototype heat exchanger tubes fabricated using the various CNT formats. The failure loads and mechanisms of the tubes under tensile, compression, and bending loads are assessed. A further comparison of the CNT materials to components fabricated from carbon fiber is made. The presented work will contribute to the selection of approaches for heat exchanger fabrication methods for nuclear propulsion and other applications.

Heat Exchanger↗

NASA NTRS1988

Alterations in crack-tip deformation during variable-amplitude fatigue crack growth

Fatigue crack growth rate changes caused by single overloads and an overload followed by an underload have been studied in the high-strength aluminum alloy 7091. Crack-tip plasticity parameters were measured at each step in the loading sequence using the stereoimaging technique. Effective stress-intensity factor was measured with high resolution immediately at the crack tip both before an overload and during the subsequent growth rate retardation period. Crack-tip opening displacement and strain were altered in the same way as growth rate following the overload/underload events, and similitude with respect to crack-tip plasticity was preserved during the growth retardation period. Effective stress-intensity factor was found to correlate well with crack growth rate. Strains within the plastic zone were converted to stress at each step in load change. These stresses were then summed to determine the zone of residual stress caused by the overload. The region of compressive residual stress ahead of the crack tip was found to increase with overload severity but was limited to yield stress in magnitude. An underload shrank the spatial extent of the residual stresses caused by the overload.

Davidson, David L.↗

NASA NTRSDate not supplied

Additive Manufacture of Porous ZrC for NTP In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Omar Mireles↗

NASA NTRSDate not supplied

Additive Manufacture of Porous Zirconium Carbide for Nuclear Thermal Propulsion In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Zirconium Carbide Additive Manufacture↗

NASA NTRSDate not supplied

Additive Manufacture of Porous Zirconium Carbide for Nuclear Thermal Propulsion In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Zirconium Carbide Additive Manufacture↗

NASA NTRS1996

Supersonic Gas-Liquid Cleaning System

The Supersonic Gas-Liquid Cleaning System Research Project consisted mainly of a feasibility study, including theoretical and engineering analysis, of a proof-of-concept prototype of this particular cleaning system developed by NASA-KSC. The cleaning system utilizes gas-liquid supersonic nozzles to generate high impingement velocities at the surface of the device to be cleaned. The cleaning fluid being accelerated to these high velocities may consist of any solvent or liquid, including water. Compressed air or any inert gas is used to provide the conveying medium for the liquid, as well as substantially reduce the total amount of liquid needed to perform adequate surface cleaning and cleanliness verification. This type of aqueous cleaning system is considered to be an excellent way of conducting cleaning and cleanliness verification operations as replacements for the use of CFC 113 which must be discontinued by 1995. To utilize this particular cleaning system in various cleaning applications for both the Space Program and the commercial market, it is essential that the cleaning system, especially the supersonic nozzle, be characterized for such applications. This characterization consisted of performing theoretical and engineering analysis, identifying desirable modifications/extensions to the basic concept, evaluating effects of variations in operating parameters, and optimizing hardware design for specific applications.

Kinney, Frank↗

NASA NTRS2012

An Efficient Analysis Methodology for Fluted-Core Composite Structures

The primary loading condition in launch-vehicle barrel sections is axial compression, and it is therefore important to understand the compression behavior of any structures, structural concepts, and materials considered in launch-vehicle designs. This understanding will necessarily come from a combination of test and analysis. However, certain potentially beneficial structures and structural concepts do not lend themselves to commonly used simplified analysis methods, and therefore innovative analysis methodologies must be developed if these structures and structural concepts are to be considered. This paper discusses such an analysis technique for the fluted-core sandwich composite structural concept. The presented technique is based on commercially available finite-element codes, and uses shell elements to capture behavior that would normally require solid elements to capture the detailed mechanical response of the structure. The shell thicknesses and offsets using this analysis technique are parameterized, and the parameters are adjusted through a heuristic procedure until this model matches the mechanical behavior of a more detailed shell-and-solid model. Additionally, the detailed shell-and-solid model can be strategically placed in a larger, global shell-only model to capture important local behavior. Comparisons between shell-only models, experiments, and more detailed shell-and-solid models show excellent agreement. The discussed analysis methodology, though only discussed in the context of fluted-core composites, is widely applicable to other concepts.

Oremont, Leonard↗

NASA NTRS2017

Investigating Access Performance of Long Time Series with Restructured Big Model Data

Data sets generated by models are substantially increasing in volume, due to increases in spatial and temporal resolution, and the number of output variables. Many users wish to download subsetted data in preferred data formats and structures, as it is getting increasingly difficult to handle the original full-size data files. For example, application research users such as those involved with wind or solar energy, or extreme weather events are likely only interested in daily or hourly model data at a single point (or for a small area) for a long time period, and prefer to have the data downloaded in a single file. With native model file structures, such as hourly data from NASA Modern-Era Retrospective analysis for Research and Applications Version-2 (MERRA-2), it may take over 10 hours for the extraction of parameters-of-interest at a single point for 30 years. The NASA Goddard Earth Sciences Data and Information Services Center (GES DISC) is exploring methods to address this particular user need. One approach is to create value-added data by reconstructing the data files. Taking MERRA-2 data as an example, we have tested converting hourly data from one-day-per-file into different data cubes, such as one-month, or one-year. Performance is compared for reading local data files and accessing data through interoperable services, such as OPeNDAP. Results show that, compared to the original file structure, the new data cubes offer much better performance for accessing long time series. We have noticed that performance is associated with the cube size and structure, the compression method, and how the data are accessed. An optimized data cube structure will not only improve data access, but also may enable better online analysis services

reanalysis↗

NASA NTRS1993

Numerical simulation of a shock wave/turbulent boundary layer interaction in a duct

A numerical investigation of the interaction of an incident oblique shock wave with a turbulent duct flow is presented. The investigation consists of solving the three-dimensional, unsteady, compressible, mass averaged Navier-Stokes equations, using an implicit finite volume, lower-upper time marching code and incorporates the three-dimensional Baldwin-Lomax turbulence model. Computed results are obtained Mach number 2.9 for a turning angle of 13 degrees and Reynolds number based on duct width of 1.36 x 10 exp 7. Under various inlet conditions, the results clearly depict the flow characteristics, including the shock geometry, the separated flow region, the wall pressure distribution, and the skin friction distribution. The findings provide a physical understanding of the three-dimensional vortex structure of the flow in a duct in which a shock wave interacts with a turbulent boundary layer. The results show that the ratio of the boundary layer thickness to the duct width is the critical parameter in determining the separation structure.

Yang, Wei-Li↗

NASA NTRS1994

Electron injection and acceleration at nonlinear shocks: Results of numerical simulations

We present results of numerical simulations of electron injection and acceleration at nonlinear high Mach number shocks. The electrons are assumed to be heated at the thermal subshock to an energy E(sub inj), which is treated as a free parameter, above which they are injected by self-generated whistlers to momentum m(sub p) x V(sub A). This injection mechanism requires Mach numbers greater than (43/(beta(sub -)))(((k T(sub e))/(E(sub inj)))(exp 1/2)), where T(sub e) and beta (sub -) are the upstream electron temperature and plasma beta parameter. Above m(sub p) x V(sub A) electrons are trapped in the shock by Alfven waves. In the proton precursor region the Alfven waves are assumed to be generated by protons accelerated at the shock, and have nonlinear intensities. Below GeV, however, electrons of a given rigidity propagate faster than protons with a similar rigidity and therefore diffuse to regions ahead of the proton precursor. In those regions the Alfven waves are generated by the electrons themselves. The diffusion coefficient appears to increase with decreasing acceleration efficiency. As a result, the number of electrons accelerated to energies GeV and above and, hence, the electron to proton ratio, depend only weakly on the extent of electron heating at the subshock. The negative feedback also renders the electron spectra insensitive to shock compression ratio and smoothing length scale. The estimated e/p ratio at GeV is between approximately 1%-10%.

Levinson, Amir↗