Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “panel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

A new measurement method for separating airborne and structureborne noise radiated by aircraft type panels

The theoretical basis for and experimental validation of a measurement method for separating airborne and structure borne noise radiated by aircraft type panels are presented. An extension of the two microphone, cross spectral, acoustic intensity method combined with existing theory of sound radiation of thin shell structures of various designs, is restricted to the frequency range below the coincidence frequency of the structure. Consequently, the method lends itself to low frequency noise problems such as propeller harmonics. Both an aluminum sheet and two built up aircraft panel designs (two aluminum panels with frames and stringers) with and without added damping were measured. Results indicate that the method is quick, reliable, inexpensive, and can be applied to thin shell structures of various designs.

Mcgary, M. C.↗

High-Speed Machining (HSM) of Space Shuttle External Tank (ET) panels

The External Fuel Tank (ET) of the Space Shuttle is not recovered after launch and a new one must be provided for each launch. Currently, the external ""skin'' panels of the tank are produced by machining from solid wrought 2219-T87 aluminum plate stock approximately 1-3/4 inch thick. The reduction of costs in producing External Fuel Tank panels is obviously of increasing production rates and decreasing costs of the panels through the application of high-speed machining (HSM) techniques was conducted.

Miller, J. A.↗

Subsonic panel method for designing wing surfaces from pressure distribution

An iterative method has been developed for designing wing section contours corresponding to a prescribed subcritical distribution of pressure. The calculations are initialized by using a surface panel method to analyze a baseline wing or wing-fuselage configuration. A first-order expansion to the baseline panel method equations is then used to calculate a matrix containing the partial derivative of potential at each control point with respect to each unknown geometry parameter. In every iteration cycle, the matrix is used both to calculate the geometry perturbation and to analyze the perturbed geometry. The distribution of potential on the perturbed geometry is established by simple linear extrapolation from the baseline solution. The extrapolated potential is converted to pressure by Bernoulli's equation. Not only is the accuracy of the approach good for very large perturbations, but the computing cost of each complete iteration cycle is substantially less than one analysis solution by a conventional panel method.

Bristow, D. R.↗

Noise transmission into semicylindrical enclosures through discretely stiffened curved panels

An analytical study of sound transmission into semicylindrical enclosures through discretely stiffened curved elastic panels is presented. The transmitted sound is estimated by solving the acoustic wave equation for the interior acoustic field, a Galerkin-like method being used. This solution is then coupled to the vibration of the stiffened panels. The response characteristics of these panels are determined by using a modal analysis where the modes are obtained by the finite element-strip method. Numerical results include spectra of the interior sound pressure due to white noise, turbulent boundary layer and propeller noise inputs.

Chang, M. T.↗

The effect of a normal shock on the aeroelastic stability of a panel

The effect of a standing shock wave on the static and dynamic aeroelastic stability of a flexible panel is investigated using a linear structural and aerodynamic theoretical model. It is found that the shock is generally stabilizing. The lowest critical dynamic pressures are associated with shock positions downstream from the panel, where the panel is uninfluenced by the shock.

Williams, M. H.↗

Evaluation of factors determining the accuracy of linearized subsonic panel methods

A systematic evaluation of the factors determining the accuracy of linearized subsonic panel methods is presented. In particular, the constant and quadratically varying doublet panel methods are compared for thin and thick surface modelings in two and three dimensions. The sensitivity of results to panel edge and control point locations is studied for both of the methods. The first order convergence of the quadratic doublet method near network edges and the subsequent effect on the Kutta condition is investigated. Results from a quadratic doublet method specifically designed for a vector processing computer are shown.

Thomas, J. L.↗

Reducing Thermal Expansivity of Composite Panels

Coefficient of thermal expansion of laminated graphite/epoxy composite panels altered after panels cured by postcuring heat treatment. Postcure decreases coefficient of thermal expansion by increasing crosslinking between molecules. Treatment makes it possible to reprocess costly panels for requisite thermal expansivity instead of discarding them.

Smith, D. D.↗

Strong, Lighweight Curved Panels

Sandwich construction gives panels structural efficiency. Large panels with compound curvatures are formed from a honeycomb core faced with sheets of graphite/epoxy cloth and tape. Developed for pod on Space Shuttle, construction readily adapted to curved skin panels on cars, trucks, and airplanes.

Molho, R.↗

Flight service evaluation of Kevlar-49 epoxy composite panels in wide-bodies commercial transport aircraft

Kevlar-49 fairing panels, installed as flight service components on three L-1011s, were inspected after 9 years of service. There are six Kevlar-49 panels on each aircraft: a left hand and right hand set of a wing body sandwich fairing; a solid laminate under wing fillet panel; and a 422 K (300 F) service aft engine fairing. The fairings have accumulated a total of 70,000 hours, with one ship set having over 24,000 hours service. The Kevlar-49 components were found to be performing satisfactorily in service with no major problems, or any condition requiring corrective action. The only defects noted were minor impact damage, a few minor disbonds and a minor degree of fastener hole fraying and elongation. These are for the most part comparable to damage noted on fiberglass fairings. The service history to date indicates that Kevlar-49 epoxy composite materials have satisfactory service characteristics for use in aircraft secondary structure.

Stone, R. H.↗

Structural efficiency studies of corrugated compression panels with curved caps and beaded webs

Curved cross-sectional elements are employed in structural concepts for minimum-mass compression panels. Corrugated panel concepts with curved caps and beaded webs are optimized by using a nonlinear mathematical programming procedure and a rigorous buckling analysis. These panel geometries are shown to have superior structural efficiencies compared with known concepts published in the literature. Fabrication of these efficient corrugation concepts became possible by advances made in the art of superplastically forming of metals. Results of the mass optimization studies of the concepts are presented as structural efficiency charts for axial compression.

Davis, R. C.↗

Concepts for improving the damage tolerance of composite compression panels

The residual strength of specimens with damage and the sensitivity to damage while subjected to an applied inplane compression load were determined for flatplate specimens and blade-stiffened panels. The results suggest that matrix materials that fail by delamination have the lowest damage tolerance capability. Alternate matrix materials or laminates which are transversely reinforced suppress the delamination mode of failure and change the failure mode to transverse shear crippling which occurs at a higher strain value. Several damage-tolerant blade-stiffened panel design concepts are evaluated. Structural efficiency studies conducted show only small mass penalties may result from incorporating these damage-tolerant features in panel design. The implication of test results on the design of aircraft structures was examined with respect to FAR requirements.

Rhodes, M. D.↗

Flight service evaluation of Kevlar-49 epoxy composite panels in wide-bodied commercial transport aircraft

Kevlar-49 fairing panels, installed as flight service components on three L-1011s, were inspected after 10 years of service. There are six Kevlar-49 panels on each aircraft: a left-hand and right-hand set of a wing-body sandwich fairing; a solid laminate under-wing fillet panel; and a 422 K (300 F) service aft engine fairing. The three L-1011s include one each in service with Eastern, Air Canada, and TWA. The fairings have accumulated a total of 79,568 hours, with one ship set having nearly 28,000 hours service. The inspections were conducted at the airlines' major maintenance bases with the participation of Lockheed Engineering. The Kevlar-49 components were found to be performing satisfactorily in service with no major problems, or any condition requiring corrective action. The only defects noted were minor impact damage, a few minor disbonds and a minor degree of fastener hole fraying and elongation. These are for the most part comparable to damage noted on fiberglass fairings. The service history obtained in this program indicates that Kevlar-49 epoxy composite materials have satisfactory service characteristics for use in aircraft secondary structure.

Stone, R. H.↗

Hot-spot investigations of utility scale panel configurations

The causes of array faults and efforts to mitigate their effects are examined. Research is concentrated on the panel for the 900 kw second phase of the Sacramento Municipal Utility District (SMUD) project. The panel is designed for hot spot tolerance without comprising efficiency under normal operating conditions. Series/paralleling internal to each module improves tolerance in the power quadrant to cell short or open circuits. Analtyical methods are developed for predicting worst case shade patterns and calculating the resultant cell temperature. Experiments conducted on a prototype panel support the analytical calculations.

Arnett, J. C.↗

Evolution of integrated panel structural design and interfaces for PV power plants

The evolution of integrated photovoltaic (PV) panel design at ARCO Solar is discussed. Historically, framed PV modules of about 1 x 4-ft size were individually mounted in the field on fixed support structures and interconnected electrically with cables to build higher-power arrays. When ARCO Solar saw the opportunity in 1982 to marry its PV modules with state-of-the-art heliostat trackers developed by ARCO Power Systems, it became obvious that mounting individual modules was impractical. For this project, the framed modules were factory-assembled into panels and interconnected with cables before being mounted on the trackers. Since then, ARCO Solar made considerable progress and gained substantial experience in the design and fabrication of large PV panels. Constraints and criteria considered in these design activities included static and dynamic loads; assembly and transportation equipment and logistics, structural and electrical interfaces, and safety and grounding concerns.

Arnett, J. C.↗

A finite element model for sound transmission through panels

A finite element method (FEM) is applied to predicting coupled frequencies and pressures within an acoustic cavity in order to characterize sound transmission through a panel. Structural equations of motion are defined and the FEM model is configured with four-noded plate elements, the lateral displacement and two slopes being the unknowns at every node. Each element then has 12 degrees of freedom (DOF) and the displacement variation is expressed by a 12-term nonconforming polynomial. A consistent mass matrix is used to represent the panel mass matrix and a wave equation governs the acoustic volume. Analysis of pressure and displacement over the panel yields a square coupling matrix, and an eigenanalysis leads to a solution of the forced vibration problem.

Ramakrishnan, J. V.↗

Space Station Engineering and Technology Development: Proceedings of the Panel on In-Space Engineering Research and Technology Development

In 1984 the ad hoc committee on Space Station Engineering and Technology Development of the Aeronautics and Space Engineering Board (ASEB) conducted a review of the National Aeronautics and Space Administration's (NASA's) space station program planning. The review addressed the initial operating configuration (IOC) of the station. The ASEB has reconstituted the ad hoc committee which then established panels to address each specific related subject. The participants of the panels come from the committee, industry, and universities. The proceedings of the Panel on In Space Engineering Research and Technology Development are presented in this report. Activities, and plans for identifying and developing R&T programs to be conducted by the space station and related in space support needs including module requirements are addressed. Consideration is given to use of the station for R&T for other government agencies, universities, and industry.

Source record↗

A nonlinear analysis of infinitely long graphite-epoxy cylindrical panels loaded with internal pressure

The structural response of internally pressurized composite cylindrical panels, representative of a transport aircraft's fuselage skins, is predicted by means of a one-dimensional, geometrically nonlinear analysis. An analytical study is conducted for the response of 4-, 8-, and 16-ply graphite/epoxy skins. The results obtained indicate that the response is geometrically nonlinear, and that a boundary layer with a severe bending gradient exists at the panel edges. The importance of through-the-thickness shearing deformations in the bending boundary layer is illustrated through comparison of analyses based on Kirchhoff-Love and shear deformation theories. Numerical results for the bending boundary layer lengths of the different panels are presented, and two bending boundary layers are predicted with the shear deformation theory.

Boitnott, R. L.↗

Modal response and noise transmission of composite panels

Noise transmission through flat, angular, fiber-reinforced composite panels is investigated experimentally and analytically. A modal decomposition technique was used to obtain solutions to the governing differential equation of motion. Experimental modal analysis was performed in order to confirm the theoretical results. The test specimens were cross-ply and angle-ply composite panels made of various concentrations of fiberglass, graphite, or aramid fibers embedded in epoxy resion. The experimental results showed good agreement with the theoretical calculations. Graphs of the transmission loss characteristics of the different composite panels are provided.

Grosveld, F. W.↗