Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “observable behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Heat of mixing and morphological stability

A mathematical model, which incorporates heat of mixing in the energy balance, has been developed to analyze the morphological stability of a planar solid-liquid interface during the directional solidification of a binary alloy. It is observed that the stability behavior is almost that predicted by the analysis of Mullins and Sekerka (1963) at low growth velocities, while deviations in the critical concentration of about 20-25 percent are observed under rapid solidification conditions for certain systems. The calculations indicate that a positive heat of mixing makes the planar interface more unstable, whereas a negative heat of mixing makes it more stable, in terms of the critical concentration.

Nandapurkar, P.↗

Investigation of surface water behavior during glaze ice accretion

Microvideo observations of glaze ice accretions on 1-in-diameter cylinders in a closed-loop refrigerated wind tunnel were obtained to study factors controlling the behavior of unfrozen surface water during glaze ice accretion. Three zones of surface water behavior were noted, each with a characteristic roughness. The effect of substrate thermal and roughness properties on ice accretions was also studied. The contact angle and hysteresis were found to increase sharply at temperatures just below 0 C, explaining the high resistance to motion of water beads observed on accreting glaze ice surfaces. Based on the results, a simple multizone modification to the current glaze ice accretion model is proposed.

Hansman, R. John, Jr.↗

A heuristic finite-state model of the human driver in a car-following situation

An approach to modeling human driver behavior in single-lane car following which is based on a finite-state decision structure is considered. The specific strategy at each point in the decision tree was obtained from observations of typical driver behavior. The synthesis of the decision logic is based on position and velocity thresholds and four states defined by regions in the phase plane. The performance of the resulting assumed intuitively logical model was compared with actual freeway data. The match of the model to the data was optimized by adapting the model parameters using a modified PARTAN algorithm. The results indicate that the heuristic model behavior matches actual car-following performance better during deceleration and constant velocity phases than during acceleration periods.

Burnham, G. O.↗

High Temperature Solid Particle Erosion of Environmental and Thermal Barrier Coatings

Solid particle erosion (SPE) is a common phenomenon observed in gas turbine engines. Particles entrained in the gas flow impact engine hardware resulting in micro-scale damage that leads to deleterious effects such as material removal. For protective coatings, damage due to SPE is a key concern since it can negatively affect the durability of the coating and subsequently the life of the underlying component. In this work, the high temperature SPE behavior of two state-of-the-art environmental barrier coatings (EBCs) deposited via air plasma spray (APS) is investigated using alumina erodent to understand the effect of particle kinetic energy, impingement angle and temperature. The SPE behavior of the EBCs is also compared to APS and electron beam – physical vapor deposition (EB-PVD) thermal barrier coatings (TBCs) to elucidate similarities and differences in the erosion response. The EBCs were more susceptible to SPE than the EB-PVD TBC but had greater SPE resistance compared to the APS TBC. Coating microstructure and porosity were shown to have a strong influence on the observed behavior.

Solid particle erosion↗

A microstructural approach to cytoskeletal mechanics based on tensegrity

Mechanical properties of living cells are commonly described in terms of the laws of continuum mechanics. The purpose of this report is to consider the implications of an alternative approach that emphasizes the discrete nature of stress bearing elements in the cell and is based on the known structural properties of the cytoskeleton. We have noted previously that tensegrity architecture seems to capture essential qualitative features of cytoskeletal shape distortion in adherent cells (Ingber, 1993a; Wang et al., 1993). Here we extend those qualitative notions into a formal microstructural analysis. On the basis of that analysis we attempt to identify unifying principles that might underlie the shape stability of the cytoskeleton. For simplicity, we focus on a tensegrity structure containing six rigid struts interconnected by 24 linearly elastic cables. Cables carry initial tension ("prestress") counterbalanced by compression of struts. Two cases of interconnectedness between cables and struts are considered: one where they are connected by pin-joints, and the other where the cables run through frictionless loops at the junctions. At the molecular level, the pinned structure may represent the case in which different cytoskeletal filaments are cross-linked whereas the looped structure represents the case where they are free to slip past one another. The system is then subjected to uniaxial stretching. Using the principal of virtual work, stretching force vs. extension and structural stiffness vs. stretching force relationships are calculated for different prestresses. The stiffness is found to increase with increasing prestress and, at a given prestress, to increase approximately linearly with increasing stretching force. This behavior is consistent with observations in living endothelial cells exposed to shear stresses (Wang & Ingber, 1994). At a given prestress, the pinned structure is found to be stiffer than the looped one, a result consistent with data on mechanical behavior of isolated, cross-linked and uncross-linked actin networks (Wachsstock et al., 1993). On the basis of our analysis we concluded that architecture and the prestress of the cytoskeleton might be key features that underlie a cell's ability to regulate its shape.

NASA Discipline Cell Biology↗

Spatial and temporal behavior of atomic oxygen determined by Ogo 6 airglow observations

Maps are produced of the atomic oxygen density near 97 km showing a strong variation in latitude, longitude, universal time, and time of year. These densities are deduced from atomic oxygen green nightglow observations carried out from Ogo 6. Meridional wind patterns needed to support the asymmetries observed in local oxygen production and loss rates are deduced.

Donahue, T. M.↗

The magnetic effects of brecciation and shock in meteorites. I - The LL-chondrites

The magnetic behavior of eight LL chondrites is analyzed in detail, and some implications for their modes of formation and evolutionary history are examined. Petrographic features of the specimens are described, and their initial magnetic characteristics are discussed. The demagnetization behavior of the initial magnetization is investigated along with the saturation remanence behavior and paleomagnetic-field intensities. The results indicate that a magnetic field of 0.01 to 0.1 Oe may have been present during postimpact cooling and that severe shock metamorphism may have given rise to the observed magnetic moments and behavior, even in the absence of ambient magnetic fields.

Brecher, A.↗

Satellite observations of the nitric oxide dayglow Implications for the behavior of mesospheric and lower-thermospheric odd nitrogen

The solar backscattered ultraviolet spectral radiometer on the Nimbus 7 satellite routinely measures fluorescence emissions from the nitric oxide (1, 4) gamma band that are imposed on the large Rayleigh-scattered signal in the wavelength range 255-256 nm. The gamma band feature, when isolated from the background radiance, provide information on the seasonal and latitudinal variations in the nitric oxide column abundance over the altitude region from 40 to 45 km upward through the thermosphere. At latitudes from 30 deg to 45 deg in the Northern Hemisphere the measurements show an annual cycle with maximum nitric oxide abundance in summer. The Southern Hemisphere pattern is qualitatively similar to this, although the amplitude of the seasonal variation is substantially smaller. The most prominent feature of the data base is a large maximum in nitric oxide emission that develops poleward of 45 deg latitude in both Hemispheres during late autumn and early winter. These maxima dissipate rapidly as spring approaches and are no longer evident in the data for Northern Hemisphere March and Southern Hemisphere September.

Frederick, J. E.↗

Creep behavior of copper at intermediate temperatures. II - Surface microstructural observations. III - A comparison with theory

Three different types of microstructural slip features are noted to occur during the creep of Cu at 0.46-0.72 of absolute melting point. While single slip is associated with higher temperatures and lower stresses, complex wavy slip features are observed at higher temperatures and higher stresses as well as with increasing strains: suggesting the importance of cross-slip mechanisms. At lower temperatures and higher stresses the multiple-slip morphologies observed indicate that cross-slip mechanisms may control the creep of polycrystalline Cu only over a limited stress and temperature range. A phenomenological model is proposed which assumes that (1) cell boundaries within subgrains act as both sources of, and obstacles to, gliding dislocations, and (2) dislocation annihilation occurs at the cell boundaries by climb and cross-slip.

Raj, S. V.↗

Ultraviolet photometry from the Orbiting Astronomical Observatory. II Interstellar extinction.

Evaluation of interstellar extinction curves over the region from 3600 to 1100 A for 17 stars. The observations were made by the two Wisconsin spectrometers on board the Orbiting Astronomical Observatory 2, with spectral resolutions of 10 and 20 A. The extinction curves generally show a pronounced maximum at 2175 plus or minus 25 A, a broad minimum in the region from 1800 to 1350 A, and finally a rapid rise to the far-ultraviolet. Large extinction variations from star to star are found, especially in the far-ultraviolet; however, with only two possible exceptions in this sample, the wavelength at the maximum of the extinction bump is essentially constant. These data are combined with visual and infrared observations to display the extinction behavior over a range in wavelength of about a factor of 20. The observations appear to require a multicomponent model of the interstellar dust.

Bless, R. C.↗

Studies conducted as a search for physical mechanisms relating solar variability and the troposphere

Chains of causative mechanisms that are hypothesized to relate solar variability to the behavior of the Earth's lower atmosphere were assessed. Solar variations believed most likely to constitute the forcing functions in hypothesized solar terrestrial atmosphere chain, changes in the Earth's atmospheric electrical characteristics due to solar variability, and the observed variations in atmospheric behavior that are influenced by solar variability were also examined.

Wu, S. T.↗

A model for the selective amplification of spatially coherent waves in a centrifugal compressor on the verge of rotating stall

A simple model for the stability zones of a low speed centrifugal compressor is developed, with the goal of understanding the driving mechanism for the changes in stalling behavior predicted for, and observed in, the Purdue Low Speed Centrifugal Research Compressor Facility. To this end, earlier analyses of rotating stall suppression in centrifugal compressors are presented in a reduced form that preserves the essential parameters of the model that affect the stalling behavior of the compressor. The model is then used to illuminate the relationship between compressor geometry, expected mode shape, and regions of amplification for weak waves which are indicative of the susceptibility of the system to rotating stall. The results demonstrate that increasing the stagger angle of the diffuser vanes, and consequently the diffusion path length, results in the compressor moving towards a condition where higher-order spatial modes are excited during stall initiation. Similarly, flow acceleration in the diffuser section caused by an increase in the number of diffuser vanes also results in the excitation of higher modes.

Lawless, Patrick B.↗

Activity Catalog Tool (ACT) user manual, version 2.0

This report comprises the user manual for version 2.0 of the Activity Catalog Tool (ACT) software program, developed by Leon D. Segal and Anthony D. Andre in cooperation with NASA Ames Aerospace Human Factors Research Division, FLR branch. ACT is a software tool for recording and analyzing sequences of activity over time that runs on the Macintosh platform. It was designed as an aid for professionals who are interested in observing and understanding human behavior in field settings, or from video or audio recordings of the same. Specifically, the program is aimed at two primary areas of interest: human-machine interactions and interactions between humans. The program provides a means by which an observer can record an observed sequence of events, logging such parameters as frequency and duration of particular events. The program goes further by providing the user with a quantified description of the observed sequence, through application of a basic set of statistical routines, and enables merging and appending of several files and more extensive analysis of the resultant data.

Segal, Leon D.↗

Comparing the Thermodynamic Behaviour of Al(1)+ZrO2(s) to Al(1)+Al2O3(s)

In an effort to better determine the thermodynamic properties of Al(g) and Al2O(g). the vapor in equilibrium with Al(l)+ZrO2(s) was compared to the vapor in equilibrium with Al(l)+Al2O3(s) over temperature range 1197-to-1509K. The comparison was made directly by Knudsen effusion-cell mass spectrometry with an instrument configured for a multiple effusion-cell vapor source (multi-cell KEMS). Second law enthalpies of vaporization of Al(g) and Al2O(g) together with activity measurements show that Al(l)+ZrO2(s) is thermodynamically equivalent to Al(l)+Al2O3(s), indicating Al(l) remained pure and Al2O3(s) was present in the ZrO2-cell. Subsequent observation of the Al(l)/ZrO2 and vapor/ZrO2 interfaces revealed a thin Al2O3-layer had formed, separating the ZrO2-cell from Al(l) and Al(g)+Al2O(g), effectively transforming it into an Al2O3 effusion-cell. This behavior agrees with recent observations made for Beta-NiAl(Pt) alloys measured in ZrO2 effusion-cell.

Copland, Evan↗

Comet Encke - Gas production and lightcurve

A comprehensive set of observations, both from the ground and with the IUE, was planned for the 1984 apparition of Comet Encke. The observations were intended to confirm the behavior seen in 1980 and to study the behavior of the comet after perihelion. The results of the observations indicate that all the measured trace species display an asymmetry around the perihelion that is consistent with the visual light curve (VLC). But the total gas production as monitored by OH (the dominant species) displays a behavior that has no relation to the VLC.

Ahearn, M. F.↗

Alternative Representations of Convective Processes in the NASA GEOS-5 AGCM

The gap in explicit resolution of phenomena between global climate models and cloud resolving models is shrinking at a steady pace with global integrations of several km in resolution now practical for at least some time scales. In moving toward finer resolution the long standing problem of convective parameterization is being examined along with the assumption of convective quasi-equilibrium and how this can be reconciled with the stochastic and intermittent nature of convection. In this context we examine the nature of parameterized convection in the NASA Goddard Earth Observing System (GEOS-5) Atmospheric General Circulation Model. Our analysis uses both coarse (2.5 degree) and fine scale 0.25 degree spatial resolution integrations. Two basic formulations are compared: the default option is the Relaxed Arakawa-Schubert (RAS) scheme which invokes a sequence of linearly entraining plumes and quasi-equilibrium closure. An optional modification of this method (the "Stochastic Tokioka" constraint) places a random lower limit on plume entrainment. An alternative representation is the Kain-Fritsch parameterization which was originally developed for mesoscale numerical modeling strategies. Here entrainment is determined by a crude buoyancy sorting approach that allows the plume spectrum to be more responsive to ambient vertical stratification of moisture. Diagnostics of the model behavior are referenced to recent observational evidence of continuous phase transition behavior. In particular we examine the relationship between column water vapor and probablility of convective presence and intensity. Sensitivity of the statistics of convective behavior to parcel mixing/entrainment formulations and parcel initial thermodynamics are considered. Observational statistics from A-Train and TRMM sensors provide validation of the model integrations.

Robertson, Franklin↗

Implications of AAOE observations for proposed chemical explanations of the seasonal and interannual behavior of Antarctic ozone

Model simulations were used to investigate the seasonal and interannual behavior of ozone for different choices of initial odd nitrogen concentration in July and different assumptions on the heterogeneous reactions, with particular consideration given to the possible contribution of chlorine chemistry to the ozone hole phenomenon. The numerical experiments were selected based on the simulations of the observed trace gas concentrations during the Airborne Antarctic Ozone Experiment in 1987. In all cases considered, the catalytic cycle associated with the formation and photolysis of Cl2O2 could account for more than half of the photochemical removal of O3 within the Antarctic vortex through mid-September. The reaction of BrO with ClO, which accounts for 15-20 percent of O3 removal in the same period, tends to play a more important role toward the end of September, when the concentration of ClO is expected to decrease. No simple relationship was found between the increase in chlorine lavel and the interannual decrease in Antarctic O3.

Ko, M. K. W.↗

BATSE Observations of Gamma-Ray Burst Spectra: Low-Energy Behavior of Time-Averaged Spectra - Part 3

We analyze time-averaged spectra from 86 bright gamma-ray bursts from the first 5 years of the Burst And Transient Source Experiment (BATSE) on board the Compton Gamma Ray Observatory to determine whether the lowest energy data are consistent with a standard spectra form fit to the data at all energies. The BATSE Spectroscopy Detectors have the capability to observe photons as low as 5 keV. Using the gamma-ray burst locations obtained with the BATSE Large Area Detectors, the Spectroscopy Detectors' low-energy response can be modeled accurately. This, together with a postlaunch calibration of the lowest energy Spectroscopy Detector discriminator channel, which can lie in the range 5-20 keV, allows spectral deconvolution over a broad energy range, approx. 5 keV to 2 MeV. The additional coverage allows us to search for evidence of excess emission, or for a deficit, below 20 keV. While no burst has a significant (greater than or equal to 3 sigma) deficit relative to a standard spectra model, we find that 12 bursts have excess low-energy emission, ranging between 1.2 and 5.8 times the model flux, that exceeds 5 sigma in significance. This is evidence for an additional low-energy spectral component in at least some bursts, or for deviations from the power-law spectral form typically used to model gamma-ray bursts at energies below 100 keV.

Preece, R. D.↗