Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “methane conversion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Cycle Evaluations of Reversible Chemical Reactions for Solar Thermochemical Energy Storage in Support of Concentrating Solar Power Generation Systems

The production and storage of thermochemical energy is a possible route to increase capacity factors and reduce the Levelized Cost of Electricity from concentrated solar power generation systems. In this paper, we present the results of cycle evaluations for various thermochemical cycles, including a well-documented ammonia closed-cycle along with open- and closed-cycle versions of hydrocarbon chemical reactions. Among the available reversible hydrocarbon chemical reactions, catalytic reforming-methanation cycles are considered; specifically, various methane-steam reforming cycles are compared to the ammonia cycle. In some cases, the production of an intermediate chemical, methanol, is also included with some benefit being realized. The best case, based on overall power generation efficiency and overall plant capacity factor, was found to be an open cycle including methane-steam reforming, using concentrated solar energy to increase the chemical energy content of the reacting stream, followed by combustion to generate heat for the heat engine.

10 SYNTHETIC FUELS↗

Scaling up carboxylic acid production from cheese whey and brewery wastewater via methane-arrested anaerobic digestion

In a circular economy, organic waste streams are valuable resources for sustainably producing chemicals and fuels. This study investigates a new methane-arrested anaerobic digestion (MAAD) process that converts high-strength cheese whey and brewery wastewater into carboxylic acids. The process was developed and optimized under various bench-scale semi-continuous (fed-batch) operating conditions (e.g., retention time, organic loading rate, pH, and feed/harvest frequency). The MAAD responses to various control-failure scenarios were also systematically investigated. The highest total acid productivity was 26g/(L liq ·d) with a substrate conversion of 0.79g COD digested /g COD fed at a hydraulic retention time (HRT) of approximately 2 d in a 14-L digester. The most stable conditions for digester operation (HRT 3 d at pH 6.0 and 40°C) were selected for process scale-up to 100gal (~380 L). Semi-continuous, pilot-scale MAAD successfully produced a total acid concentration of 40.6+/-1.1 g/L with 8.1% acetic acid, 45.1% butyric acid, and 44.5% lactic acid. The links between wastewater characteristics, operation mode, digester scale, and microbial community structure were statistically analyzed. The results show genera Sporolactobacillus and Clostridium positively correlate with butyric acid production (Pearson correlation coefficient>0.5). Moreover, four kinetic models were developed and fit to batch MAAD experimental datasets (R 2 >95%) and were successfully applied to predict the total acid production in both bench-and pilot-scale semi-continuous MAADs. In conclusion, this study shows MAAD has the potential for industrial-scale applications and is a robust platform to valorize low- or negative-value waste streams into high-value bioproducts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Driving terrestrial ecosystem models from space

Regional air pollution, land-use conversion, and projected climate change all affect ecosystem processes at large scales. Changes in vegetation cover and growth dynamics can impact the functioning of ecosystems, carbon fluxes, and climate. As a result, there is a need to assess and monitor vegetation structure and function comprehensively at regional to global scales. To provide a test of our present understanding of how ecosystems operate at large scales we can compare model predictions of CO2, O2, and methane exchange with the atmosphere against regional measurements of interannual variation in the atmospheric concentration of these gases. Recent advances in remote sensing of the Earth's surface are beginning to provide methods for estimating important ecosystem variables at large scales. Ecologists attempting to generalize across landscapes have made extensive use of models and remote sensing technology. The success of such ventures is dependent on merging insights and expertise from two distinct fields. Ecologists must provide the understanding of how well models emulate important biological variables and their interactions; experts in remote sensing must provide the biophysical interpretation of complex optical reflectance and radar backscatter data.

Waring, R. H.↗

Heterogeneous and Framework-Bound Copper Species Contribute to Catalytic Partial Methane Oxidation in Cu–Chabazite Zeolites

The relationship between continuous partial methane oxidation (PMO) rates and Cu site speciation in Cu-CHA zeolite catalysts is explored through differential rate measurements across a series of samples of varying compositions combined with density functional theory, first-principles thermodynamics, and statistical models that characterize Cu speciation. Under continuous PMO conditions (573 K, 0.07 kPa O 2 , 3 kPa H 2 O), Cu ions are shown to anchor to the CHA framework in both monomeric (Z 2 Cu and Z 2 CuH 2 O) and dimeric (O- and OH-bridged Cu) forms that are sensitive to the identity of the local framework anchoring site. Consequently, across the studied compositional range, Cu-CHA catalysts are predicted to contain a mixture of monomeric and dimeric Cu sites. Cu-normalized CH 3 OH formation rates extrapolated to zero conversion reflect contributions from multiple site types. Predicted CH 3 OH formation rates indicate that the Cu site reactivity toward CH 4 is influenced by zeolite composition and is likely limited by the reduction half-cycle.

03 NATURAL GAS↗

Final Technical Report "Catalytic Hydrogenation of Carbon Monoxide and Olefin Oxidation" Grant number : DE-FG02-86ER13615

Title: Catalytic Hydrogenation of Carbon Monoxide and Olefin Oxidation Grant No. DE-FG02-86ER13615 PI: Wayland, B. B. (wayland@sas.upenn.edu) Abstract Development of new mechanistic strategies and catalyst materials for activation of CO, H2, CH4, C2H4, O2, and related substrates relevant to the conversion of carbon monoxide, alkanes, and alkenes to organic oxygenates are central objectives encompassed by this program. Design and synthesis of metal complexes that manifest reactivity patterns associated with potential pathways for the hydrogenation of carbon monoxide through metallo-formyl (M-CHO), dimetal ketone (M-C(O)-M), and dimetal dionyl (M-C(O)-C(O)-M) species is one major focus. Hydrocarbon oxidation using molecular oxygen is a central goal for methane activation and functionalization as well as regioselective oxidation of olefins. Discovery of new reactivity patterns and control of selectivity are pursued through designing new metal complexes and adjusting reaction conditions. Variation of reaction media promotes distinct reaction pathways that control both reaction rates and selectivities. Dimetalloradical diporphyrin complexes preorganize transition states for substrate reactions that involve two metal centers and manifest large rate increases over mono-metalloradical reactions of hydrogen, methane, and other small molecule substrates. Another broad goal and recurring theme of this program is to contribute to the thermodynamic database for a wide scope of organo-metal transformations in a range of reaction media. One of the most complete descriptions of equilibrium thermodynamics for organometallic reactions in water and methanol is emerging from the study of rhodium porphyrin substrate reactions in aqueous and alcoholic media. Water soluble group nine metalloporphyrins manifest remarkably versatile substrate reactivity in aqueous and alcoholic media which includes producing rhodium formyl (Rh-CHO) and hydroxy methyl (Rh-CH2OH) species. Exploratory directions for this program include expending new strategies for anti-Markovnikov addition of water, alcohols, and amines with olefins, developing catalytic reactions of CO to give formamides and formic esters, and evaluating the potential for coupling reactions of CO to produce organic building blocks.

10 SYNTHETIC FUELS↗

Advanced Research Projects Agency - Energy Annual Report for FY 2015

This report presents a summary of the activities of the Advanced Research Projects Agency-Energy (ARPA-E) during Fiscal Year 2015 (FY 2015). In FY 20151, ARPA-E selected projects for nine new programs covering a broad array of energy technologies, including: 30 million dollars for low-cost tools to aid in the future development of fusion power (ALPHA); 30 million dollars for new power plant cooling technologies that enable high thermal-to-electric energy conversion efficiency with zero net water dissipation to the atmosphere (ARID); 6 million dollars for validation of the performance of ARPA-E-funded grid-storage technologies (CHARGES); 30 million dollars for systems for localized thermal management to improve building efficiency (DELTA); 25 million dollars for development of generator technologies to enable more affordable and efficient residential Combined Heat and Power (CHP) systems (GENSETS); 30 million dollars for low-cost, highly sensitive systems to detect methane emissions (MONITOR); 24 million dollars for micro-scale concentrated photovoltaic systems (MOSAIC); 30 million dollars to integrate agriculture, information technology and engineering to develop crops that are sustainable, affordable and yield abundant plant feedstocks for bioenergy (TERRA); 14.5 million dollars for systems to identify less energy-intense travel options for users using software accessible on smartphones or other communications devices (TRANSNET).

24 POWER TRANSMISSION AND DISTRIBUTION↗

Scanning Electrochemical Flow Cell with Online Mass Spectroscopy for Accelerated Screening of Carbon Dioxide Reduction Electrocatalysts

Electrochemical conversion of carbon dioxide into valuable chemicals or fuels is an increasingly important strategy for achieving carbon neutral technologies. The lack of a sufficiently active and selective electrocatalyst, particularly for synthesizing highly reduced products, motivates accelerated screening to evaluate new catalyst spaces. Traditional techniques, which couple electrocatalyst operation with analytical techniques to measure product distributions, enable screening throughput at 1–10 catalysts per day. In this paper, a combinatorial screening instrument is designed for MS detection of hydrogen, methane, and ethylene in quasi-real-time during catalyst operation experiments in an electrochemical flow cell. Coupled with experiment modeling, product detection during cyclic voltammetry (CV) enables modeling of the voltage-dependent partial current density for each detected product. Here, we demonstrate the technique by using the well-established thin film Cu catalysts and by screening a Pd–Zn composition library in carbonate-buffered aqueous electrolyte. The rapid product distribution characterization over a large range of overpotential makes the instrument uniquely suited for accelerating screening of electrocatalysts for the carbon dioxide reduction reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Life-Cycle Analysis of Alternative Aviation Fuels in GREET

The Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model, developed at Argonne National Laboratory, has been expanded to include well-to-wake (WTWa) analysis of aviation fuels and aircraft. This report documents the key WTWa stages and assumptions for fuels that represent alternatives to petroleum jet fuel. The aviation module in GREET consists of three spreadsheets that present detailed characterizations of well-to-pump and pump-to-wake parameters and WTWa results. By using the expanded GREET version (GREET1{_}2011), we estimate WTWa results for energy use (total, fossil, and petroleum energy) and greenhouse gas (GHG) emissions (carbon dioxide, methane, and nitrous oxide) for (1) each unit of energy (lower heating value) consumed by the aircraft or (2) each unit of distance traveled/ payload carried by the aircraft. The fuel pathways considered in this analysis include petroleum-based jet fuel from conventional and unconventional sources (i.e., oil sands); Fisher-Tropsch (FT) jet fuel from natural gas, coal, and biomass; bio-jet fuel from fast pyrolysis of cellulosic biomass; and bio-jet fuel from vegetable and algal oils, which falls under the American Society for Testing and Materials category of hydroprocessed esters and fatty acids. For aircraft operation, we considered six passenger aircraft classes and four freight aircraft classes in this analysis. Our analysis revealed that, depending on the feedstock source, the fuel conversion technology, and the allocation or displacement credit methodology applied to co-products, alternative bio-jet fuel pathways have the potential to reduce life-cycle GHG emissions by 55-85 percent compared with conventional (petroleum-based) jet fuel. Although producing FT jet fuel from fossil feedstock sources - such as natural gas and coal - could greatly reduce dependence on crude oil, production from such sources (especially coal) produces greater WTWa GHG emissions compared with petroleum jet fuel production unless carbon management practices, such as carbon capture and storage, are used.

01 COAL, LIGNITE, AND PEAT↗

San Francisco Biofuel Program: Brown Grease to Biodiesel Demonstration (Project Report)

Municipal wastewater treatment facilities have typically been limited to the role of accepting wastewater, treating it to required levels, and disposing of its treatment residuals. However, a new view is emerging which includes wastewater treatment facilities as regional resource recovery centers. This view is a direct result of increasingly stringent regulations, concerns over energy use, carbon footprint, and worldwide depletion of fossil fuel resources. Resources in wastewater include chemical and thermal energy, as well as nutrients, and water. A waste stream such as residual grease, which concentrates in the drainage from restaurants (referred to as Trap Waste), is a good example of a resource with an energy content that can be recovered for beneficial reuse. If left in wastewater, grease accumulates inside of the wastewater collection system and can lead to increased corrosion and pipe blockages that can cause wastewater overflows. Also, grease in wastewater that arrives at the treatment facility can impair the operation of preliminary treatment equipment and is only partly removed in the primary treatment process. In addition, residual grease increases the demand in treatment materials such as oxygen in the secondary treatment process. When disposed of in landfills, grease is likely to undergo anaerobic decay prior to landfill capping, resulting in the atmospheric release of methane, a greenhouse gas (GHG). This research project was therefore conceptualized and implemented by the San Francisco Public Utilities Commission (SFPUC) to test the feasibility of energy recovery from Trap Waste in the form of Biodiesel or Methane gas. The research goals are given below: To validate technology performance; To determine the costs and benefits [including economic, socioeconomic, and GHG emissions reduction] associated with co-locating this type of operation at a municipal wastewater treatment plant (WWTP); To develop a business case or model for replication of the program by other municipal agencies (as applicable). In order to accomplish the goals of the project, the following steps were performed: 1. Operation of a demonstration facility designed to receive 10,000 to 12,000 gallons of raw Trap Waste each day from private Trap Waste hauling companies. The demonstration facility was designed and built by Pacific Biodiesel Technologies (PBTech). The demonstration facility would also recover 300 gallons of Brown Grease per day from the raw Trap Waste. The recovered Brown Grease was expected to contain no more than 2% Moisture, Insolubles, and Unsaponifiables (MIU) combined. 2. Co-digestion of the side streams (generated during the recovery of 300 gallons of Brown Grease from the raw Trap Waste) with wastewater sludge in the WWTP's anaerobic digesters. The effects of the side streams on anaerobic digestion were quantified by comparison with baseline data. 3. Production of 240 gallons per day of ASTM D6751-S15 grade Biodiesel fuel via a Biodiesel conversion demonstration facility, with the use of recovered Brown Grease as a feedstock. The demonstration facility was designed and built by Blackgold Biofuels (BGB). Side streams from this process were also co-digested with wastewater sludge. Bench-scale anaerobic digestion testing was conducted on side streams from both demonstration facilities to determine potential toxicity and/or changes in biogas production in the WWTP anaerobic digester. While there is a lot of theoretical data available on the lab-scale production of Biodiesel from grease Trap Waste, this full-scale demonstration project was one of the first of its kind in the United States. The project's environmental impacts were expected to include: Reduction of greenhouse gas emissions by prevention of the release of methane at landfills. Although the combustion product of Biodiesel and Methane gas produced in the Anaerobic digester, Carbon Dioxide, is also a greenhouse gas; it is 20 times weaker for the same amount (per mole) released, making its discharge preferable to that of Methane. The use of Biodiesel in place of fossil-fuel derived Diesel was expected to reduce net Carbon Dioxide, Ash Particulate, Sulfate, Silicate, and Soot emissions, thereby improving air quality.

09 BIOMASS FUELS↗

The engine reformer: Syngas production in an engine for compact gas‐to‐liquids synthesis

Methane (CH 4 ) reforming was carried out in an internal combustion engine (an “engine reformer”). We successfully produced syngas from the partial oxidation of natural gas in the cylinder of a diesel engine that was reconfigured to perform spark ignition. Performing the reaction in an engine cylinder allows some of the exothermicity to be captured as useful work. Intake conditions of 110 kPa and up to 480 °C allowed low cycle‐to‐cycle variability ( COV nimep < 20 %) at methane‐air equivalence ratios ( ϕ M ) of 2.0, producing syngas with an H 2 ‐to‐CO ratio of 1.4. Spark ignition timing was varied between 45–30° before top‐dead‐center (BTDC) piston position, showing significant improvement with delayed timing. Hydrogen (H 2 ) and ethane (C 2 H 6 ) were added to simulate recycle from a downstream synthesis reactor and realistic natural gas compositions, respectively. Adding these gases yielded a stable combustion up to hydrocarbon‐air equivalence ratios ( ϕ HC ) of 2.8 with COV nimep < 5 %. Ethane concentrations (with respect to methane) of up to 0.2 L/L (20 vol%) (with and without H 2 ) produced robust and stable combustions, demonstrating that the engine can be operated across a range of natural gas compositions. Engine exhaust soot concentrations demonstrated elevated values at ϕ HC > 2.4, but < 1 mg/L below these equivalence ratios. These results demonstrate that the engine reformer could be a key component of a compact gas‐to‐liquids synthesis plant by highlighting the operating conditions under which high gas conversion, high H 2‐ to‐CO ratios close to 2.0, and low soot production are possible.

Lim, Emmanuel G.↗

Metagenomic analysis of microbial consortium from natural crude oil that seeps into the marine ecosystem offshore Southern California

Crude oils can be major contaminants of the marine ecosystem and microorganisms play a significant role in the degradation of the main constituents of crude oil. To increase our understanding of the microbial hydrocarbon degradation process in the marine ecosystem, we collected crude oil from an active seep area located in the Santa Barbara Channel (SBC) and generated a total of about 52 Gb of raw metagenomic sequence data. The assembled data comprised ~500 Mb, representing ~1.1 million genes derived primarily from chemolithoautotrophic bacteria. Members of Oceanospirillales, a bacterial order belonging to the Deltaproteobacteria, recruited less than 2% of the assembled genes within the SBC metagenome. In contrast, the microbial community associated with the oil plume that developed in the aftermath of the Deepwater Horizon (DWH) blowout in 2010, was dominated by Oceanospirillales, which comprised more than 60% of the metagenomic data generated from the DWH oil plume. This suggests that Oceanospirillales might play a less significant role in the microbially mediated hydrocarbon conversion within the SBC seep oil compared to the DWH plume oil. We hypothesize that this difference results from the SBC oil seep being mostly anaerobic, while the DWH oil plume is aerobic. Within the Archaea, the phylum Euryarchaeota, recruited more than 95% of the assembled archaeal sequences from the SBC oil seep metagenome, with more than 50% of the sequences assigned to members of the orders Methanomicrobiales and Methanosarcinales. These orders contain organisms capable of anaerobic methanogenesis and methane oxidation (AOM) and we hypothesize that these orders and their metabolic capabilities may be fundamental to the ecology of the SBC oil seep.

archaea↗

Chapter 8: Metabolic Engineering of Methanotrophic Bacteria for Industrial Biomanufacturing

CH4 offers a promising, high-volume petroleum replacement for fuel and chemical bioprocesses. Recent advances in gas recovery technologies have facilitated access to previously inaccessible natural gas reserves, while biogas generated from anaerobic digestion of waste streams offers a versatile, renewable CH4 source. Importantly, CH4 is also the second most abundant greenhouse gas (GHG), with nearly 60% of emissions derived from anthropogenic sources. However, the gaseous state of CH4 makes for a lack of compatibility with current transportation and industrial manufacturing infrastructure, limiting its utilization as a transportation fuel and intermediate in biochemical processes. Resurgent interest in CH4 upgrading has pushed microbial conversion of CH4 to fuels and value-added chemicals to the forefront of industrial bioprocessing. CH4 bioconversion offers both CH4 valorization and GHG emission reduction potential and importantly offers a scalable, modular, and selective approach to CH4 utilization compared to conventional physical and chemical conversion strategies. However, as noted above, advances in CH4 biocatalysis have been constrained by limited genetic tractability of natural CH4-consuming microbes. In this chapter, we review recent advances in methanotrophic genetic and genomic tool development and metabolic engineering.

09 BIOMASS FUELS↗

Life cycle analysis of gasification and Fischer-Tropsch conversion of municipal solid waste for transportation fuel production

Non-recyclable municipal solid waste (MSW) can be used as feedstock for liquid fuel production via gasification followed by Fischer-Tropsch (FT) processes. Given the heterogeneity of MSW material composition and variation in material properties, its convertibility to liquid hydrocarbon fuels could vary widely, affecting the sustainability of utilizing non-recyclable MSW for fuel production. This study evaluates the life cycle greenhouse gas (GHG) emissions (carbon intensities [CIs]) of FT fuels from non-recyclable MSW. Key issues that could greatly affect the CIs were examined, including fossil carbon content of the MSW, emission implications of diverting non-recyclable MSW from landfills to fuel production, and conversion efficiency. Results show that the CIs of fuels produced from various waste streams range 80–105 gCO2e/MJ, which may exceed the CI of petroleum fuels. Higher fossil carbon content in the MSW feedstock tends to incur higher GHG emissions as biogenic carbon emissions are considered carbon neutral. Meanwhile, diverting different fractions of non-recyclable MSW, such as food waste and low-quality paper, from landfills may result in GHG emissions that may include the potential avoidance of methane emissions and potential sequestration of biogenic carbon that is foregone. To reduce GHG emissions, a carbon capture and sequestration option in the fuel production stage is considered, which could reduce the CI by 53–64 gCO2e/MJ. Carbon fates of different non-recyclable MSW in landfills are further evaluated to determine how they vary and impact the CIs of MSW-derived fuels.

02 PETROLEUM↗

Rh-Based Mixed Alcohol Synthesis Catalysts: Characterization and Computational Report

The U.S. Department of Energy is conducting a program focused on developing a process for the conversion of biomass to bio-based fuels and co-products. Biomass-derived syngas is converted thermochemically within a temperature range of 240 to 330°C and at elevated pressure (e.g., 1200 psig) over a catalyst. Ethanol is the desired reaction product, although other side compounds are produced, including C 3 to C 5 alcohols; higher (i.e., greater than C 1 ) oxygenates such as methyl acetate, ethyl acetate, acetic acid and acetaldehyde; and higher hydrocarbon gases such as methane, ethane/ethene, propane/propene, etc. Saturated hydrocarbon gases (especially methane) are undesirable because they represent a diminished yield of carbon to the desired ethanol product and represent compounds that must be steam reformed at high energy cost to reproduce CO and H 2 . Ethanol produced by the thermochemical reaction of syngas could be separated and blended directly with gasoline to produce a liquid transportation fuel. Additionally, higher oxygenates and unsaturated hydrocarbon side products such as olefins also could be further processed to liquid fuels. The goal of the current project is the development of a Rh-based catalyst with high activity and selectivity to C 2 + oxygenates. This report chronicles an effort to characterize numerous supports and catalysts to identify particular traits that could be correlated with the most active and/or selective catalysts. Carbon and silica supports and catalysts were analyzed. Generally, analyses provided guidance in the selection of acceptable catalyst supports. For example, supports with high surface areas due to a high number of micropores were generally found to be poor at producing oxygenates, possibly because of mass transfer limitations of the products formed out of the micropores. To probe fundamental aspects of the complicated reaction network of CO with H 2 , a computational/ theoretical investigation using quantum mechanical and ab initio molecular dynamics calculations was initiated in 2009. Computational investigations were performed first to elucidate understanding of the nature of the catalytically active site. Thermodynamic calculations revealed that Mn likely exists as a metallic alloy with Rh in Rh-rich environments under reducing conditions at the temperatures of interest. After determining that reduced Rh-Mn alloy metal clusters were in a reduced state, the activation energy barriers of numerous transition state species on the catalytically active metal particles were calculated to compute the activation barriers of several reaction pathways that are possible on the catalyst surface. Comparison of calculations with a Rh nanoparticle versus a Rh-Mn nanoparticle revealed that the presence of Mn enabled the reaction pathway of CH with CO to form an adsorbed CHCO species, which was a precursor to C 2 + oxygenates. The presence of Mn did not have a significant effect on the rate of CH 4 production. Ir was observed during empirical catalyst screening experiments to improve the activity and selectivity of Rh-Mn catalysts. Thus, the addition of Ir to the Rh-Mn nanoparticles also was probed computationally. Simulations of Rh-Mn-Ir nanoparticles revealed that, with sufficient Ir concentrations, the Rh, Mn and Ir presumably would be well mixed within a nanoparticle. Activation barriers were calculated for Rh-Mn-Ir nanoparticles for several C-, H-, and O-containing transitional species on the nanoparticle surface. It was found that the presence of Ir opened yet another reactive pathway whereby HCO is formed and may undergo insertion with CHx surface moieties. The reaction pathway opened by the presence of Ir is in addition to the CO + CH pathway opened by the presence of Mn. Similar to Mn, the presence of Ir was not found to not affect the rate of CH 4 production.

catalyst↗

Producing Clean Syngas via Catalytic Reforming for Fuels Production

Thermochemical biomass conversion to fuels and chemicals can be achieved through gasification to syngas. The biomass derived raw syngas contains the building blocks of carbon monoxide and hydrogen as well as impurities such as tars, light hydrocarbons, and hydrogen sulfide. These impurities must be removed prior to fuel synthesis. We used catalytic reforming to convert tars and hydrocarbons to additional syngas, which increases biomass carbon utilization. In this work, nickel based, fluidizable tar reforming catalysts were synthesized and evaluated for tar and methane reforming performance with oak and model syngas in two types of pilot scale fluidized reactors (recirculating and recirculating regenerating). Because hydrogen sulfide (present in raw syngas and added to model syngas) reacts with the active nickel surface, regeneration with steam and hydrogen was required. Pre and post catalyst characterization showed changes specific to the syngas type used. Results of this work will be discussed in the context of selecting the best process for pilot scale demonstration.

09 BIOMASS FUELS↗

Dynamic Electric Field Assisted CO 2 Methanation

Energy-efficient advanced chemical reactions are essential for accelerating the growth of hydrocarbon economy. Sabatier reaction stands out for its potential to effectively transform carbon dioxide into valuable hydrocarbons and is an asset for long-duration Mars missions. This study explores a novel catalytic approach that harnesses electric field-assisted catalysis to substantially enhance the efficiency of the Sabatier reaction. Application of a dynamically perturbed electric field at 1000 Hz resulted in remarkable enhancements, increasing methane formation rates by over 100% at 350 °C and by 74% at 400 °C. Post-reaction catalyst characterization further revealed reduced blockage of active catalytic surface area under the applied electric field, emphasizing improved catalytic longevity and sustained activity. These results underscore the potential of tailored electric field waveforms to dynamically modulate elementary reaction kinetics and surface processes, positioning electric field-assisted catalysis as a transformative strategy for energy-efficient, cost-effective chemical manufacturing and energy conversion technologies.

42 - ENGINEERING↗

Hydrogen Isotope Measurements of Organic Acids and Alcohols by Pyrolysis-GC-MS-TC-IRMS: Application to Analysis of Experimentally Derived Hydrothermal Mineral-Catalyzed Organic Products

We report results of experiments to measure the H isotope composition of organic acids and alcohols. These experiments make use of a pyroprobe interfaced with a GC and high temperature extraction furnace to make quantitative H isotope measurements. This work compliments our previous work that focused on the extraction and analysis of C isotopes from the same compounds [1]. Together with our carbon isotope analyses our experiments serve as a "proof of concept" for making C and H isotope measurements on more complex mixtures of organic compounds on mineral surfaces in abiotic hydrocarbon formation processes at elevated temperatures and pressures. Our motivation for undertaking this work stems from observations of methane detected within the Martian atmosphere [2-5], coupled with evidence showing extensive water-rock interaction during Mars history [6-8]. Methane production on Mars could be the result of synthesis by mineral surface-catalyzed reduction of CO2 and/or CO by Fischer-Tropsch Type (FTT) reactions during serpentization [9,10]. Others have conducted experimental studies to show that FTT reactions are plausible mechanisms for low-molecular weight hydrocarbon formation in hydrothermal systems at mid-ocean ridges [11-13]. Our H isotope measurements utilize an analytical technique combining Pyrolysis-Gas Chromatograph-Mass Spectrometry-High Temperature Conversion-Isotope Ratio Mass Spectrometry (Py-GC-MS-TC-IRMS). This technique is designed to carry a split of the pyrolyzed GC-separated product to a Thermo DSQII quadrupole mass spectrometer as a means of making qualitative and semi-quantitative compositional measurements of separated organic compounds, therefore both chemical and isotopic measurements can be carried out simultaneously on the same sample.

Socki, Richard A.↗

CO2 Reduction Assembly Prototype Using Microlith-Based Sabatier Reactor for Ground Demonstration

The utilization of CO2 to produce life support consumables, such as O2 and H2O, via the Sabatier reaction is an important aspect of NASA's cabin Atmosphere Revitalization System (ARS) and In-Situ Resource Utilization (ISRU) architectures for both low-earth orbit and long-term manned space missions. Carbon dioxide can be reacted with H2, obtained from the electrolysis of water, via Sabatier reaction to produce methane and H2O. Methane can be stored and utilized as propellant while H2O can be either stored or electrolyzed to produce oxygen and regain the hydrogen atoms. Depending on the application, O2 can be used to replenish the atmosphere in human-crewed missions or as an oxidant for robotic and return missions. Precision Combustion, Inc. (PCI), with support from NASA, has previously developed an efficient and compact Sabatier reactor based on its Microlith® catalytic technology and demonstrated the capability to achieve high CO2 conversion and CH4 selectivity (i.e., ≥90% of the thermodynamic equilibrium values) at high space velocities and low operating temperatures. This was made possible through the use of high-heat-transfer and high-surface-area Microlith catalytic substrates. Using this Sabatier reactor, PCI designed, developed, and demonstrated a stand-alone CO2 Reduction Assembly (CRA) test system for ground demonstration and performance validation. The Sabatier reactor was integrated with the necessary balance-of-plant components and controls system, allowing an automated, single "push-button" start-up and shutdown. Additionally, the versatility of the test system prototype was demonstrated by operating it under H2-rich (H2/CO2 of >4), stoichiometric (ratio of 4), and CO2-rich conditions (ratio of <4) without affecting its performance and meeting the equilibrium-predicted water recovery rates. In this paper, the development of the CRA test system for ground demonstration will be discussed. Additionally, the performance results from testing the system at various operating conditions and the results from durability testing will be presented.

Junaedi, Christian↗