Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “membrane surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Polarization- and angle-dependent characteristics in two dimensional photonic crystal membrane reflectors

We report here measured angle- and polarization-dependent reflection properties in two-dimensional photonic crystal broadband membrane reflectors. Polarization independent reflection was obtained at surface normal direction. High reflection can also be obtained for one transverse electric (TE) polarization state over a wide range of incident angles. With the target of 1550 nm spectral band, the measured spectral bandwidths for TE polarization with reflectivity greater than 90% are 180 nm and 56 nm at surface normal and oblique incidence of 45°, respectively. The experimental spectrum approximates the theoretical spectral response of this membrane reflector.

36 MATERIALS SCIENCE↗

Fracture modes in tubular LSFCO ceramic membranes under graded reducing conditions

Highlights: ► Microstructural evolution in LSFCO membranes under graded environment is reported. ► The role of chemically induced stresses and oxygen deficiency is evaluated. ► The stress distribution is modeled by a point defect model. - Abstract: Chromium (III) oxide (Cr{sub 2}O{sub 3})-doped LaSrFeO{sub 3} perovskite, La{sub 0.2}Sr{sub 0.8}Fe{sub 0.8}Cr{sub 0.2}O{sub 3−δ} (LSFCO), is being considered as a potential material for applications in solid oxide fuel cells, gas separation membranes, and electrochemical reactors because of its high electro-catalytic activity. Similar to other perovskites, the performance and mechanical strength of LSFCO materials are significantly affected by environment and temperature. Here, we report a fracture gradient phenomenon in tubular C-ring-shaped LSFCO ceramic membranes under graded reducing conditions. The graded reducing condition was produced by flushing N{sub 2} on the outer side of the C-ring membranes at 1000 °C while keeping the inner side untreated. The rings were then diametrically compressed to fracture, and the resultant fracture morphology was analyzed with a scanning electron microscope (SEM). A fracture gradient with three distinct regions across the thickness of the membranes was identified on the split surfaces. In the outer region of the C-ring specimen exposed to N{sub 2}, a mixed inter/transgranular fracture with a predominant intergranular pattern was observed. In the middle section of the fracture surface, a characteristic transgranular fracture of the perovskite grains was found. At the inner region of the ring, a mixed inter/transgranular fracture with a predominant transgranular pattern occurred. The mechanism of gradient fractures was attributed both to chemically induced stresses caused by oxygen diffusion and to the formation of a separate phase of oxygen-deficient perovskite in the parent perovskite. The stresses generated were modeled by a point defect model. This work provides significant information on microstructure evolutions of tubular LSFCO membranes under graded reducing atmospheres.

36 MATERIALS SCIENCE↗

Air-stable droplet interface bilayers on oil-infused surfaces

Droplet interface bilayers (DIBs) are versatile model membranes useful for synthetic biology and biosensing; however, to date they have always been confined to fluid reservoirs. Here, we demonstrate that when two or more water droplets collide on an oil-infused substrate, they exhibit non-coalescence due to the formation of a thin oil film that gets squeezed between the droplets from the bottom-up. We show that when phospholipids are included in the water droplets, a stable droplet interface bilayer forms between the non-coalescing water droplets. As with traditional oil-submerged DIBs, we were able to characterize ion channel transport by incorporating peptides into each droplet. Our findings reveal that droplet interface bilayers can function in air environments, which could potentially enable biosensing of atmospheric particulates.

Boreyko, Jonathan B↗

Electro-Mechanical Simulation of a Large Aperture MOEMS Fabry-Perot Tunable Filter

We are developing a micro-machined electrostatically actuated Fabry-Perot tunable filter with a large clear aperture for application in high through-put wide-field imaging spectroscopy and lidar systems. In the first phase of this effort, we are developing key components based on coupled electro-mechanical simulations. In particular, the movable etalon plate design leverages high coating stresses to yield a flat surface in drum-head tension over a large diameter (12.5 mm). In this approach, the cylindrical silicon movable plate is back etched, resulting in an optically coated membrane that is suspended from a thick silicon support ring. Understanding the interaction between the support ring, suspended membrane, and coating is critical to developing surfaces that are flat to within stringent etalon requirements. In this work, we present the simulations used to develop the movable plate, spring suspension system, and electrostatic actuation mechanism. We also present results from tests of fabricated proof of concept components.

Kuhn, Jonathan L.↗

The endomembrane requirement for cell surface repair

The capacity to reseal a plasma membrane disruption rapidly is required for cell survival in many physiological environments. Intracellular membrane (endomembrane) is thought to play a central role in the rapid resealing response. We here directly compare the resealing response of a cell that lacks endomembrane, the red blood cell, with that of several nucleated cells possessing an abundant endomembrane compartment. RBC membrane disruptions inflicted by a mode-locked Ti:sapphire laser, even those initially smaller than hemoglobin, failed to reseal rapidly. By contrast, much larger laser-induced disruptions made in sea urchin eggs, fibroblasts, and neurons exhibited rapid, Ca(2+)-dependent resealing. We conclude that rapid resealing is not mediated by simple physiochemical mechanisms; endomembrane is required.

NASA Discipline Cell Biology↗

Excess chemical potential of small solutes across water--membrane and water--hexane interfaces

The excess chemical potentials of five small, structurally related solutes, CH4, CH3F, CH2F2, CHF3, and CF4, across the water-glycerol 1-monooleate bilayer and water-hexane interfaces were calculated at 300, 310, and 340 K using the particle insertion method. The excess chemical potentials of nonpolar molecules (CH4 and CF4) decrease monotonically or nearly monotonically from water to a nonpolar phase. In contrast, for molecules that possess permanent dipole moments (CH3F, CH2F, and CHF3), the excess chemical potentials exhibit an interfacial minimum that arises from superposition of two monotonically and oppositely changing contributions: electrostatic and nonelectrostatic. The nonelectrostatic term, dominated by the reversible work of creating a cavity that accommodates the solute, decreases, whereas the electrostatic term increases across the interface from water to the membrane interior. In water, the dependence of this term on the dipole moment is accurately described by second order perturbation theory. To achieve the same accuracy at the interface, third order terms must also be included. In the interfacial region, the molecular structure of the solvent influences both the excess chemical potential and solute orientations. The excess chemical potential across the interface increases with temperature, but this effect is rather small. Our analysis indicates that a broad range of small, moderately polar molecules should be surface active at the water-membrane and water-oil interfaces. The biological and medical significance of this result, especially in relation to the mechanism of anesthetic action, is discussed.

NASA Center ARC↗

Membrane contactor/separator for an advanced ozone membrane reactor for treatment of recalcitrant organic pollutants in water

An advanced ozone membrane reactor that synergistically combines membrane distributor for ozone gas, membrane contactor for pollutant adsorption and reaction, and membrane separator for clean water production is described. The membrane reactor represents an order of magnitude improvement over traditional semibatch reactor design and is capable of complete conversion of recalcitrant endocrine disrupting compounds (EDCs) in water at less than three minutes residence time. Coating the membrane contactor with alumina and hydrotalcite (Mg/Al=3) adsorbs and traps the organics in the reaction zone resulting in 30% increase of total organic carbon (TOC) removal. Large surface area coating that diffuses surface charges from adsorbed polar organic molecules is preferred as it reduces membrane polarization that is detrimental to separation. - Graphical abstract: Advanced ozone membrane reactor synergistically combines membrane distributor for ozone, membrane contactor for sorption and reaction and membrane separator for clean water production to achieve an order of magnitude enhancement in treatment performance compared to traditional ozone reactor. Highlights: Black-Right-Pointing-Pointer Novel reactor using membranes for ozone distributor, reaction contactor and water separator. Black-Right-Pointing-Pointer Designed to achieve an order of magnitude enhancement over traditional reactor. Black-Right-Pointing-Pointer Al{sub 2}O{sub 3} and hydrotalcite coatings capture and trap pollutants giving additional 30% TOC removal. Black-Right-Pointing-Pointer High surface area coating prevents polarization and improves membrane separation and life.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reactor physics characterization of triply periodic minimal surface-based nuclear fuel lattices

Triply periodic minimal surface (TPMS) lattices are receiving substantial attention in numerous engineering fields due to their impressive topology-driven physical characteristics. TPMS lattices are periodic structures of two distinct intertwined volume domains separated by an area-minimizing surface or wall. TPMS lattices have been observed in nature, such as biological membranes, skeletons, block copolymers, sea urchins, butterfly wings, and equipotential surfaces in crystals. Intriguingly, the topology of TPMS lattices can be easily parametrized via level-set equations and thus are heavily numerically and experimentally studied. Here, a significant research effort is currently applying TPMS lattices for heat exchangers and sinks. This paper extends TPMS lattice applications to nuclear reactor fuel designs, with a focus on identifying relevant TPMS geometric parameters controlling neutronics characteristics, such as reactivity, neutron spectrum, and heat removal properties. We found that fuel surface-area-to-volume ratios for TPMS lattices can be two orders of magnitude larger than current cylindrical fuel rods. Further, the selected TPMS lattice and its implicit equation, the unit cell pitch, wall thickness, and structure porosity are design parameters enabling neutronics optimization for both thermal and fast spectrum configurations, paving the way for exceptionally compact and dense nuclear core concepts.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Heterobinuclear Light Absorber Coupled to Molecular Wire for Charge Transport across Ultrathin Silica Membrane for Artificial Photosynthesis

Coupling of robust, all-inorganic heterobinuclear light absorbers to metal oxide catalysts for water oxidation across an ultrathin product-separating silica membrane requires charge transfer through organic molecular wires embedded in the silica. A synthetic approach for assembling the bimetallic units on the silica surface is introduced that is compatible with the presence of encapsulated organic molecules. Accurate selection and fine tuning of the concentration of embedded conducting wires are enabled by a two-step method consisting of surface attachment of a tripodal anchor, trimethoxysilyl aniline, followed by attachment of p-oligo(phenylene vinylene) through amide linkage. Each step of the assembly process was monitored and characterized by a combination of Fourier transform infrared, Fourier transform-Raman, and UV-vis spectroscopy techniques. Hole transfer was observed from transient Co III , formed by Ti IV OCo II → Ti III OCo III charge transfer excitation of the chromophore, to p-oligo(phenylene vinylene) molecule within the 8 ns width of the photolysis laser pulse by transient optical absorption spectroscopy of the wire radical cation. The rectifying property of the light absorber-wire assembly enabled by appropriate selection of redox potentials of metals and embedded wire obviates the need for a molecularly defined linkage between the components. Combined with the previously observed ultrafast hole injection from the embedded wires to Co oxide catalyst, the result implies visible-light-induced hole transfer from visible-light-excited binuclear light absorber to water oxidation catalyst across the silica separation membrane in a few nanoseconds or faster. Finally, demonstration and understanding of this interfacial charge-transfer step is critical for developing nanoscale core-shell architectures for complete photosynthetic cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Endocytosis of the non-catalytic ADAM23: Recycling and long half-life properties

A Disintegrin And Metalloprotease 23 (ADAM23) is a member of the ADAMs family of transmembrane proteins, mostly expressed in nervous system, and involved in traffic and stabilization of Kv1-potassium channels, synaptic transmission, neurite outgrowth, neuronal morphology and cell adhesion. Also, ADAM23 has been linked to human pathological conditions, such as epilepsy, cancer metastasis and cardiomyopathy. ADAM23 functionality depends on the molecule presence at the cell surface and along the secretory pathway, as expected for a cell surface receptor. Because endocytosis is an important functional regulatory mechanism of plasma membrane receptors and no information is available about the traffic or turnover of non-catalytic ADAMs, we investigated ADAM23 internalization, recycling and half-life properties. Here, we show that ADAM23 undergoes constitutive internalization from the plasma membrane, a process that depends on lipid raft integrity, and is redistributed to intracellular vesicles, especially early and recycling endosomes. Furthermore, we observed that ADAM23 is recycled from intracellular compartments back to the plasma membrane and thus has longer half-life and higher cell surface stability compared with other ADAMs. Our findings suggest that regulation of ADAM23 endocytosis/stability could be exploited therapeutically in diseases in which ADAM23 is directly involved, such as epilepsy, cancer progression and cardiac hypertrophy.

60 APPLIED LIFE SCIENCES↗

Tailoring Biomimetic Phosphorylcholine-Containing Block Copolymers as Membrane-Targeting Cellular Rescue Agents

Some synthetic polymers can block cell death when applied following an injury that would otherwise kill the cell. This cellular rescue occurs through interactions of the polymers with cell membranes. However, general principles for designing synthetic polymers to ensure strong, but nondisruptive, cell membrane targeting are not fully elucidated. Here, we tailored biomimetic phosphorylcholine-containing block copolymers to interact with cell membranes and determined their efficacy in blocking neuronal death following oxygen-glucose deprivation. By adjusting the hydrophilicity and membrane affinity of poly(2-methacryloyloxyethyl phosphorylcholine) (polyMPC)-based triblock copolymers, the surface active regime in which the copolymers function effectively as membrane-targeting cellular rescue agents was determined. We identified nonintrusive interactions between the polymer and the cell membrane that alter the collective dynamics of the membrane by inducing rigidification without disrupting lipid packing or membrane thickness. Furthermore, our results open new avenues for biological applications of polyMPC-based polymers and provide an approach to designing membrane-targeting agents to block cell death after injury.

59 BASIC BIOLOGICAL SCIENCES↗

Optimizing Immobilized Enzyme Performance in Cell-Free Environments to Produce Liquid Fuels

Limitations on biofuel production using cell culture (Escherichia coli, Clostridium, Saccharomyces cerevisiae, brown microalgae, blue-green algae and others) include low product (alcohol) concentrations (≤0.2 vol%) due to feedback inhibition, instability of cells, and lack of economical product recovery processes. To overcome these challenges, an alternate simplified biofuel production scheme was tested based on a cell-free immobilized enzyme system. Using this cell free system, we were able to obtain about 2.6 times higher concentrations of iso-butanol using our non-optimized system as compared with live cell systems. This process involved two steps: (i) converts acid to aldehyde using keto-acid decarboxylase (KdcA), and (ii) produces alcohol from aldehyde using alcohol dehydrogenase (ADH) with a cofactor (NADH) conversion from inexpensive formate using a third enzyme, formate dehydrogenase (FDH). To increase stability and conversion efficiency with easy separations, the first two enzymes were immobilized onto methacrylate resin. Fusion proteins of labile KdcA (fKdcA) were expressed to stabilize the covalently immobilized KdcA. Covalently immobilized ADH exhibited long-term stability and efficient conversion of aldehyde to alcohol over multiple batch cycles without fusions. High conversion rates and low protein leaching were achieved by covalent immobilization of enzymes on methacrylate resin. The complete reaction scheme was demonstrated by immobilizing both ADH and fKdcA and using FDH free in solution. The new system without in situ removal of isobutanol achieved a 55% conversion of ketoisovaleric acid to isobutanol at a concentration of 0.5 % (v/v). Further increases in titer will require continuous removal of the isobutanol using our novel brush membrane system that exhibits a 1.5 fold increase in the separation factor of isobutanol from water versus that obtained for commercial silicone rubber membranes. These bio-inspired brush membranes are based on the presence of glycocalyx filaments coating the luminal surface of our vasculature and represent a new class of synthetic membranes. They thus meet the requirements/scope of the Bimolecular Materials program, Materials Science and Engineering Div., Office of Science, US DOE.

09 BIOMASS FUELS↗

Ankyrin and band 3 differentially affect expression of membrane glycoproteins but are not required for erythroblast enucleation

Highlights: Black-Right-Pointing-Pointer Ankyrin and band 3 are not required for erythroblasts enucleation. Black-Right-Pointing-Pointer Loss of ankyrin does not affect erythroid membrane glycoprotein expression. Black-Right-Pointing-Pointer Loss of band 3 influences erythroid membrane glycoprotein expression. -- Abstract: During late stages of mammalian erythropoiesis the nucleus undergoes chromatin condensation, migration to the plasma membrane, and extrusion from the cytoplasm surrounded by a segment of plasma membrane. Since nuclear condensation occurs in all vertebrates, mammalian erythroid membrane and cytoskeleton proteins were implicated as playing important roles in mediating the movement and extrusion of the nucleus. Here we use erythroid ankyrin deficient and band 3 knockout mouse models to show that band 3, but not ankyrin, plays an important role in regulating the level of erythroid cell membrane proteins, as evidenced by decreased cell surface expression of glycophorin A in band 3 knockout mice. However, neither band 3 nor ankyrin are required for enucleation. These results demonstrate that mammalian erythroblast enucleation does not depend on the membrane integrity generated by the ankyrin-band 3 complex.

60 APPLIED LIFE SCIENCES↗

Nanoscale simulation of the thylakoid membrane response to extreme temperatures

Abstract The thylakoid membrane is in a temperature‐sensitive equilibrium that shifts repeatedly during the life cycle in response to ambient temperature or solar irradiance. Plants respond to seasonal temperature variation by changing their thylakoid lipid composition, while a more rapid mechanism for short‐term heat exposure is required. The emission of the small organic molecule isoprene has been postulated as one such possible rapid mechanism. The protective mechanism of isoprene is unknown, but some plants emit isoprene at high temperature. We investigate the dynamics and structure for lipids within a thylakoid membrane across temperatures and varied isoprene content using classical molecular dynamics simulations. The results are compared with experimental findings for temperature‐dependent changes in the lipid composition and shape of thylakoids. The surface area, volume, and flexibility of the membrane, as well as the lipid diffusion, increase with temperature, while the membrane thickness decreases. Saturated thylakoid 34:3 glycolipids derived from eukaryotic synthesis pathways exhibit altered dynamics relative to lipids from prokaryotic synthesis paths, which could explain the upregulation of specific lipid synthesis pathways at different temperatures. Increasing isoprene concentration was not observed to have a significant thermoprotective effect on the thylakoid membranes, and that isoprene readily permeated the membrane models tested.

59 BASIC BIOLOGICAL SCIENCES↗

Adjustable Membrane Mirrors Incorporating G-Elastomers

Lightweight, flexible, large-aperture mirrors of a type being developed for use in outer space have unimorph structures that enable precise adjustment of their surface figures. A mirror of this type includes a reflective membrane layer bonded with an electrostrictive grafted elastomer (G-elastomer) layer, plus electrodes suitably positioned with respect to these layers. By virtue of the electrostrictive effect, an electric field applied to the G-elastomer membrane induces a strain along the membrane and thus causes a deflection of the mirror surface. Utilizing this effect, the mirror surface figure can be adjusted locally by individually addressing pairs of electrodes. G-elastomers, which were developed at NASA Langley Research Center, were chosen for this development in preference to other electroactive polymers partly because they offer superior electromechanical performance. Whereas other electroactive polymers offer, variously, large strains with low moduli of elasticity or small strains with high moduli of elasticity, G-elastomers offer both large strains (as large as 4 percent) and high moduli of elasticity (about 580 MPa). In addition, G-elastomer layers can be made by standard melt pressing or room-temperature solution casting.

Chang, Zensheu↗

Advanced Membrane Separation Technologies for Energy Recovery from Industrial Process Streams

Recovery of energy from relatively low-temperature waste streams is a goal that has not been achieved on any large scale. Heat exchangers do not operate efficiently with low-temperature streams and thus require such large heat exchanger surface areas that they are not practical. Condensing economizers offer one option for heat recovery from such streams, but they have not been widely implemented by industry. A promising alternative to these heat exchangers and economizers is a prototype ceramic membrane system using transport membrane technology for separation of water vapor and recovery of heat. This system was successfully tested by the Gas Technology Institute (GTI) on a natural gas fired boiler where the flue gas is relatively clean and free of contaminants. However, since the tubes of the prototype system were constructed of aluminum oxide, the brittle nature of the tubes limited the robustness of the system and even limited the length of tubes that could be used. In order to improve the robustness of the membrane tubes and make the system more suitable for industrial applications, this project was initiated with the objective of developing a system with materials that would permit the system to function successfully on a larger scale and in contaminated and potentially corrosive industrial environments. This required identifying likely industrial environments and the hazards associated with those environments. Based on the hazardous components in these environments, candidate metallic materials were identified that are expected to have sufficient strength, thermal conductivity and corrosion resistance to permit production of longer tubes that could function in the industrial environments identified. Tests were conducted to determine the corrosion resistance of these candidate alloys, and the feasibility of forming these materials into porous substrates was assessed. Once the most promising metallic materials were identified, the ability to form an alumina membrane layer on the surface of the metallic tubes was evaluated. Evaluation of this new style of membrane tube involved exposure to SO 2 containing gases as well as to materials with a potential for fouling. Once the choice of substrate and membrane materials and design were confirmed, about 150 tubes were fabricated and assembled into three modules. These modules were mounted on an industrial size boiler and their performance carefully monitored during a limited testing period. The positive results of this performance test confirm the feasibility of utilizing such a system for recovery of heat and water from industrial waste streams. The improved module design along with use of long metallic substrate tubes with a ceramic membrane on the outer surface resulted in the successful, limited scale demonstration of the Transport Membrane Condenser (TMC) technology in the GTI test facility. This test showed this technology can successfully recover a significant amount of heat and water from gaseous waste streams. However, before industry will make the investment to install a full scale TMC, a full scale system will need to be constructed, installed and successfully operated at a few industrial sites. Companies were identified that had an interest in serving as a host site for a demonstration system.

Keiser, James R.↗

Design of graphene sheets-supported Pt catalyst layer in PEM fuel cells

A series of cathodes using Pt supported onto graphene sheets with different contents of carbon black in the catalyst layer were prepared and characterized. Carbon black was added as a spacer between two-dimensional graphene sheets in the catalyst layer to study its effect on the performances of proton exchange membrane fuel cell. Electrochemical properties and surface morphology of the cathodes with and without carbon black were characterized using cyclic voltammetry, ac-impedance spectroscopy, electrochemical polarization technique, and scanning electron microscopy. The results indicated that carbon black effectively modifies the array of graphene supports, resulting in more Pt nanoparticles available for electrochemical reaction and better mass transport in the catalyst layer.

30 DIRECT ENERGY CONVERSION↗

Theoretical vibrational sum-frequency generation spectroscopy of water near lipid and surfactant monolayer interfaces

Understanding the structure of water near cell membranes is crucial for characterizing water-mediated events such as molecular transport. To obtain structural information of water near a membrane, it is useful to have a surface-selective technique that can probe only interfacial water molecules. One such technique is vibrational sum-frequency generation (VSFG) spectroscopy. As model systems for studying membrane headgroup/water interactions, in this paper we consider lipid and surfactant monolayers on water. We adopt a theoretical approach combining molecular dynamics simulations and phase-sensitive VSFG to investigate water structure near these interfaces. Our simulated spectra are in qualitative agreement with experiments and reveal orientational ordering of interfacial water molecules near cationic, anionic, and zwitterionic interfaces. OH bonds of water molecules point toward an anionic interface leading to a positive VSFG peak, whereas the water hydrogen atoms point away from a cationic interface leading to a negative VSFG peak. Coexistence of these two interfacial water species is observed near interfaces between water and mixtures of cationic and anionic lipids, as indicated by the presence of both negative and positive peaks in their VSFG spectra. In the case of a zwitterionic interface, OH orientation is toward the interface on the average, resulting in a positive VSFG peak.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗