Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “measurement errors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Critical Practices in Rigorously Assessing the Inherent Activity of Nanoparticle Electrocatalysts

Accurate activity measurements for electrocatalytic materials are the backbone of impactful electrocatalyst research. Inherent to accurate measurements is the correct accounting of the active catalyst sites and the design of experiments to ensure that these sites are participating in the measured reaction. Improvements in electrocatalyst activity for fuel cell reactions (hydrogen oxidation and oxygen reduction) are essential for the widespread adoption of this carbon-neutral energy source. Activities for these half-reactions can be reported in a variety of ways including specific activities, mass activities, volumetric activities, and half-wave potentials. These values are traditionally measured with a rotating disk electrode (RDE) in which the electrocatalyst is supported on a porous active layer film attached to the RDE. To accurately measure electrocatalyst activity with an RDE, two major sources of errors must be addressed: (i) accurate electrochemical surface area (ECSA) quantification and (ii) fast diffusion of reactants through the active layer film. In this contribution, we first aim to detail through RDE experiments and mass transport modeling the potential errors that can be observed when these factors are not properly addressed. We then present recommendations and discuss techniques for properly constructing electrocatalyst thin films and characterizing the ECSA on monometallic and novel alloy electrocatalysts. These practices, when adopted, ensure greater confidence and reliability in reports of electrocatalyst activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Simultaneous Observations of Surface Layer Profiles of Humidity, Temperature, and Wind Using Scanning Lidar Instruments

We demonstrate the combination of three Doppler lidars (DLs), a water vapor differential absorption lidar and a temperature rotational Raman lidar for the investigation of the interactions between the land-surface and the atmospheric boundary layer. This combination of scanning lidars was operated for the first time during the Land-Atmosphere Feedback Experiment at the Atmospheric Radiation Measurement program's Southern Great Plain site, Oklahoma, USA, in August 2017, and provided simultaneous surface layer profiles of horizontal wind, humidity and temperature. The horizontal wind profiles were determined using the dual-Doppler method with two DLs. The scans were performed above four towers providing atmospheric variables and fluxes. These combined lidar data allowed for the estimation of the friction velocity as well as the surface latent and sensible heat fluxes. For this purpose, profiles calculated with Monin-Obukhov similarity theory were fitted with the Levenberg-Marquardt nonlinear least squares curve-fitting method to the measured surface-layer lidar profiles. We present case studies of three 50-min periods to illustrate the new method. The measurements resulted in friction velocities of 0.31, 0.29, and 0.38 ms –1 , sensible surface heat fluxes of 312.1, 234.1, and 183.3 Wm –2 and latent surface heat fluxes of 251.8, 227.3, and 274.4 Wm –2 . These values were compared with the in-situ measurements of the towers. Considering the sampling differences and the error analyses, the results agree within 25.1%, 42.5%, and 28.8%, respectively, demonstrating that this synergy of scanning active remote sensing systems can be used to derive surface fluxes with reasonable accuracy.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Development of an ultraprecise glue-free bimorph deformable mirror with a length of 460 mm

Lead zirconate titanate (PZT) bimorph mirrors are essential for performing multiple functions, such as beam shaping, wavefront correction, and dynamic focusing with adjustable beam sizes. They typically consist of a mirror substrate with PZT electrodes bonded to the substrate using a thin epoxy film. However, glue-bonded PZT mirrors exhibit low reproducibility in measurement results. One source of this variability is water absorption by the substrate’s epoxy adhesive during wet fabrication processes, such as elastic emission machining (EEM), which leads to swelling and deformation. Additionally, longer deformable bimorph mirrors require larger PZT electrodes, further complicating their design and fabrication, particularly during bonding and ultraprecise metrology. To address these challenges, silver nanoparticles were employed to bond PZT elements to the silicon (Si) mirror, eliminating the need for epoxy glue. Here, in this study, we developed an inorganic-glue-free PZT bimorph mirror with a length of 460 mm and 28 channels. The glue-free bonding method successfully ensured the high reproducibility of measurements after water immersion. This approach resulted in a shape error of only 0.41 nm root mean square after the figure correction process using an ultraprecise EEM process. Scanning acoustic tomography and basic response function tests confirmed the success of the bonding process, showing no critical voids. Furthermore, the shape changes induced by applying voltages to the PZT electrodes closely matched predictions obtained from simulations. These results demonstrate the reliability and precision of the proposed glue-free bonding technique, paving the way for improved performance of new PZT bimorph mirrors.

Ichii, Yoshio [SLAC National Accelerator Laborator↗
DOE OSTI2022

SDSS-IV MaStar: [α/Fe] for the MaNGA Stellar Library from synthetic model spectra

ABSTRACT We calculate the α-enhancement ratio [α/Fe] for the Mapping Nearby Galaxies at APO (MaNGA) Stellar Library (MaStar) while also fitting for the fundamental atmospheric parameters effective temperature, surface gravity, and metallicity – Teff, log g, [Fe/H]. This approach builds upon a previous catalogue of stellar parameters, whereby only the fundamental atmospheric parameters are fit with solar-scaled models. Here, we use the same Markov Chain Monte Carlo method with the additional free parameter [α/Fe]. Using the full spectral fitting code pPXF, we are able to fit multiple lines sensitive to [α/Fe] for a more robust measurement. Quality flags based on the convergence of the sampler, errors in [α/Fe] and a cut in the χ2 of the model fit are used to clean the final catalogue, returning 17 214 spectra and values in the range of −0.25 < [α/Fe] < 0.48. Comparing our calculated [α/Fe] with literature values reveals a degeneracy in cool stars with log g ≥ ∼4; this comparison is then used to create an alternative and calibrated parameter set. We also plot the final catalogue in an [Fe/H] versus [α/Fe] diagram and recover the expected result of increasing [α/Fe] with decreasing [Fe/H] for Milky Way disc-halo stars. We apply our method to a subsample of spectra of uniform resolution and higher signal to noise that finds that our results are independent of this higher signal to noise. In the context of stellar population models, we are able to cover a parameter space for the creation of intermediate to old age models at solar-scaled [α/Fe], high [Fe/H] and enhanced [α/Fe], low [Fe/H].

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2026

Predicting the dark matter-baryon abundance ratio

We discuss relaxation solutions to the dark matter-baryon coincidence problem in the context of QCD axion dark matter. In relaxation solutions, a moduli dynamically adjusts the mass of dark matter and baryons until their energy densities are 𝒪⁡(1) the same. Because the QCD axion is heavily connected to QCD, scanning the QCD axion mass inherently also scans the proton mass. In the context of relaxation solutions, this implies that the ratio of dark matter to baryon abundances (Ω DM /Ω B ) is a ratio of beta functions showing that these models can only accommodate discrete values of ΩDM/ΩB thereby “predicting” the ratio of the dark matter to baryon abundances. The original composite axion model has only a single integer degree of freedom 𝑁, the size of the gauge group, and we show that when 𝑁 =8 the observed value of Ω DM /Ω B =5.36 is reproduced to within its percent level error bars. Novel tests of this model include more precise measurements of Ω DM /Ω B , a better lattice determination of the dependence of the proton mass on the high energy QCD gauge coupling, as well as more traditional tests such as fifth force experiments.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

High-fidelity imaging of a band insulator in a three-dimensional optical lattice clock

Here, we report on the observation of a high-density, band insulating state in a three-dimensional optical lattice clock. Filled with a nuclear-spin-polarized degenerate Fermi gas of 87 Sr, the three-dimensional (3D) lattice has one atom per site in the ground motional state, thus guarding against frequency shifts due to contact interactions. At this high density where the average distance between atoms is comparable to the probe wavelength, conventional imaging techniques at saturation intensity suffer from large systematic errors. To spatially probe frequency shifts in the clock and measure thermodynamic properties of this system, accurate imaging techniques at high optical depths are required. Using a combination of highly saturated fluorescence and absorption imaging, we confirm the density distribution in our 3D optical lattice in agreement with a single spin band insulating state. Combining our clock platform with this high filling fraction opens the door to studying new classes of long-lived, many-body states arising from dipolar interactions.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

High-Fidelity Two-Qubit Gates Using a Microelectromechanical-System-Based Beam Steering System for Individual Qubit Addressing

In a large scale trapped atomic ion quantum computer, high-fidelity two-qubit gates need to be extended over all qubits with individual control. We realize and characterize high-fidelity two-qubit gates in a system with up to four ions using radial modes. The ions are individually addressed by two tightly focused beams steered using microelectromechanical system mirrors. We deduce a gate fidelity of 99.49(7)% in a two-ion chain and 99.30(6)% in a four-ion chain by applying a sequence of up to 21 two-qubit gates and measuring the final state fidelity. Our team characterizes the residual errors and discuss methods to further improve the gate fidelity towards values that are compatible with fault-tolerant quantum computation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

An Experiment-based Distribution Level Performance Comparison among PMUs

This paper presents a experiment-based distribution level performance comparison among three Phasor Measurement Units (PMUs). Several evaluation criteria, including the total vector error, the phase angle error, the frequency error, the rate of change of frequency, the response time, the settling time, the overshoot, and the algorithm window size, are selected to compare the static and dynamic performances of the PMUs under steady state and step response test conditions. In order to have a more realistic test environment, a test is setup in which PMUs under evaluation have exactly the same input signals. The quantitative experiment result analysis gives an end-user guideline to the PMU selection regarding distribution level applications.

Yin, He↗
DOE OSTI2026

Secure Wireless Communication Using Distributed Coherent Transmission and Spatial Signal Decomposition

We present a new approach to secure wireless communications using coherent distributed transmission of signals that are spatially decomposed between a two-element distributed antenna array. High-accuracy distributed coordination of microwave wireless systems supports the ability to transmit different parts of a signal from separate transmitters such that they combine coherently at a designated destination. In this article, we explore this concept using a two-element coherent distributed phased array where each of the two transmitters sends a separate component of a communication signal, where each symbol is decomposed into a sum of two pseudorandom signal vectors, the coherent summation of which yields the intended symbol. By directing the transmission to an intended receiver using distributed beamforming, the summation of the two vector components is largely confined to a spatial region at the destination receiver. We implement the technique in a $50−λ$ array operating at 3 GHz. We evaluate the symbol error rate (SER) in 2-D space through simulation and measurement, showing that the approach yields a spatially confined secure region where the information is recoverable (i.e., the received signal has low SER), and outside of which the information is unrecoverable (high SER). The proposed system is also compared against a traditional beamforming system where each node sends the same data. We validate experimentally that our approach achieves a low SER of 0.0082 at broadside and an SER above 0.25 at all other locations compared to a traditional beamforming approach that achieves a SER of 0 at all locations measured.

Engineering - Electronic and electrical engineerin↗
DOE OSTI2020

Accuracy of HVAC Load Predictions: Validation of EnergyPlus and DOE-2 using FLEXLAB Measurements

The aim of the project reported here was to better understand the level of accuracy of three building energy simulation (BES) engines (‘engines’) — EnergyPlus™, DOE-2.1e, and DOE-2.2 — by identifying and investigating significant deviations between the performance predicted by these engines and actual performance as measured in the FLEXLAB® test facility at Lawrence Berkeley National Laboratory (LBNL). The specific test conditions included some of those prescribed in ANSI/ASHRAE Standard 140 - Standard Method of Test for the Evaluation of Building Energy Analysis Computer Programs. Detailed measurements of FLEXLAB performance, including indoor temperatures and heat fluxes and air-flow and water flow rates and temperatures in the Heating, Ventilating and Air Conditioning (HVAC) system, together with hourly weather data, were recorded and used in analyzing the simulation results from EnergyPlus v8.8, DOE-2.2 v3.65 and DOE-2.1e v127. These engines are commonly used in the United States for building energy code compliance, federal, state, and utility incentives programs, as well as energy efficient design of new buildings and energy retrofit of existing buildings. Seven conventional overhead mixing ventilation scenarios were tested and each engine was found to have a similar level of agreement with the measurements of space-level heating and sensible cooling loads. These results provide useful information regarding the accuracy of these engines in predicting the cooling and heating load elements of whole building energy performance. This information is intended for practitioners who are concerned about transitioning between simulation tools with different engines and for managers of utility programs leveraging these tools for evaluating and/or projecting measure savings to be incentivized under their programs. The results of the comparisons of simulated and measured performance indicate that the predictions from all three engines are not significantly different. The 24-hour average value of the absolute mean bias indicates the likely magnitude of the error in any particular case. The average mean bias is reduced by cancelation of overprediction in one case by underprediction in another. The daytime absolute mean biases, which may be more important for both energy performance and occupant comfort, are ~6%, presumably because of the greater complexity involved in simulating in the presence of solar radiation. EnergyPlus typically overpredicts the cooling load and/or underpredicts the heating load by ~1.5% and the DOE-2 engines typically underpredict the cooling load by approximately the same amount. The Root Mean Square Error is relatively more sensitive to shorter term variations in the difference between predicted and measured loads; the three engines have similar values, ~10%, suggesting that the uncertainties in their predictions of peak loads may also be similar in magnitude. The implication of these results is that users, both designers and program analysts, can use EnergyPlus, DOE-2.1e, or DOE-2.2 to model conventional commercial buildings equipped with overhead mixing ventilation with a similar level of confidence. Further work is required to better understand the variability in the level of agreement between the engine predictions and FLEXLAB measurements, where a particular engine will agree well with FLEXLAB in some cases and not so well in others and another engine will agree or disagree in different cases. As the sources of this variability are identified and eliminated or reduced significantly, it is recommended that the experimental capabilities and methods developed in the study reported here should be applied to validating heating and cooling load calculations for spaces with different types of furniture and miscellaneous loads. These methods should then be applied to low energy space conditioning systems in EnergyPlus including, in particular, radiant slab and radiant ceiling panel cooling and heating systems and ‘mixed mode’ systems that combine mechanical cooling and natural ventilation systems, focusing on controls, including control of thermal mass. The work reported here addresses the conventional method of heating and cooling occupied spaces; other methods, such as the use of radiant heating and cooling systems have the potential to provide equivalent occupant comfort, or better, with lower energy consumption. These systems are addressed more explicitly in EnergyPlus but there is a need for empirical validation to give users the same level of confidence in modeling these systems that they have, or should have, in modeling conventional systems, based on the results presented here.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Dark Energy Survey Year 6 Results: Point-Spread Function Modeling

We present the point-spread function (PSF) modeling for weak lensing shear measurement using the full six years of the Dark Energy Survey (DES Y6) data. We review the PSF estimation procedure using the PIFF (PSFs In the Full FOV) software package and describe the key improvements made to PIFF and modeling diagnostics since the DES year three (Y3) analysis: (i) use of external Gaia and infrared photometry catalogs to ensure higher purity of the stellar sample used for model fitting, (ii) addition of color-dependent PSF modeling, the first for any weak lensing analysis, and (iii) inclusion of model diagnostics inspecting fourth-order moments, which can bias weak lensing measurements to a similar degree as second-order modeling errors. Through a comprehensive set of diagnostic tests, we demonstrate the improved accuracy of the Y6 models evident in significantly smaller systematic errors than those of the Y3 analysis, in which all g band data were excluded due to insufficiently accurate PSF models. For the Y6 weak lensing analysis, we include g band photometry data in addition to the riz bands, providing a fourth band for photometric redshift estimation. Looking forward to the next generation of wide-field surveys, we describe several ongoing improvements to PIFF, which will be the default PSF modeling software for weak lensing analyses for the Vera C. Rubin Observatory’s Legacy Survey of Space and Time.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

In-Situ Measurement of Power Loss for Crystalline Silicon Modules Undergoing Thermal Cycling and Mechanical Loading Stress Testing

An in-situ method is proposed for monitoring and estimating the power degradation of mc-Si photovoltaic (PV) modules undergoing thermo-mechanical degradation tests that primarily manifest through cell cracking, such as mechanical load tests, thermal cycling and humidity freeze tests. The method is based on in-situ measurement of the module’s dark current-voltage (I-V) characteristic curve during the stress test, as well as initial and final module flash testing on a Sun simulator. The method uses superposition of the dark I-V curve with final flash test module short-circuit current to account for shunt and junction recombination losses, as well as series resistance estimation from the in-situ measured dark I-Vs and final flash test measurements. The method is developed based on mc-Si standard modules undergoing several stages of thermo-mechanical stress testing and degradation, for which we investigate the impact of the degradation on the modules light I-V curve parameters, and equivalent solar cell model parameters. Experimental validation of the method on the modules tested shows good agreement between the in-situ estimated power degradation and the flash test measured power loss of the modules, of up to 4.31 % error (RMSE), as the modules experience primarily junction defect recombination and increased series resistance losses. However, the application of the method will be limited for modules experiencing extensive photo-current degradation or delamination, which are not well reflected in the dark I-V characteristic of the PV module.

14 SOLAR ENERGY↗
DOE OSTI2020

An LES-based airborne Doppler lidar simulator and its application to wind profiling in inhomogeneous flow conditions

Wind profiling by Doppler lidar is common practice and highly useful in a wide range of applications. Airborne Doppler lidar can provide additional insights relative to ground-based systems by allowing for spatially distributed and targeted measurements. Providing a link between theory and measurement, a first large eddy simulation (LES)-based airborne Doppler lidar simulator (ADLS) has been developed. Simulated measurements are conducted based on LES wind fields, considering the coordinate and geometric transformations applicable to real-world measurements. The ADLS provides added value as the input truth used to create the measurements is known exactly, which is nearly impossible in real-world situations. Thus, valuable insight can be gained into measurement system characteristics as well as retrieval strategies. As an example application, airborne Doppler lidar wind profiling is investigated using the ADLS. For commonly used airborne velocity azimuth display (AVAD) techniques, flow homogeneity is assumed throughout the retrieval volume, a condition which is violated in turbulent boundary layer flow. Assuming an ideal measurement system, the ADLS allows to isolate and evaluate the error in wind profiling which occurs due to the violation of the flow homogeneity assumption. Overall, the ADLS demonstrates that wind profiling is possible in turbulent wind field conditions with reasonable errors (root mean squared error of 0.36 m s –1 for wind speed when using a commonly used system setup and retrieval strategy for the conditions investigated). Nevertheless, flow inhomogeneity, e.g., due to boundary layer turbulence, can cause an important contribution to wind profiling error and is non-negligible. Results suggest that airborne Doppler lidar wind profiling at low wind speeds (<5 m s –1 ) can be biased, if conducted in regions of inhomogeneous flow conditions.

17 WIND ENERGY↗
DOE OSTI2021

Methods and devices for preventing computationally explosive calculations in a computer for model parameters distributed on a hierarchy of geometric simplices

A computer-implemented method of preventing computationally explosive calculations. The method includes obtaining, by a processor of the computer, measured data of one of a physical process or a physical object; performing hierarchical numerical modeling of a physical process inclusive of an Earth model containing at least one of (a) infrastructure in the ground and (b) a formation feature in the ground, wherein predicted data is generated; comparing the measured data to the predicted data to calculate an estimated error; analyzing the estimated error via an inversion process to update the at least one of the Earth model and infrastructure model so as to reduce the estimated error and to determine a final composite Earth model of at least one of the infrastructure and the feature; and using the final composite Earth model to characterize at least one of the process and the physical object.

Source record↗
DOE OSTI2023

Neutron Leakage Spectra of the EUCLID Experiment [Abstract]

Integral experiments with sub-critical and critical configurations of special nuclear material are performed in support of nuclear data validation and adjustment. Different nuclear data evaluations may have different values for individual cross sections due to uncertainties in (or lack of) differential experiments, but compensating errors in these data sets can lead to the same k eff results for one application while vastly different for another application. One example of this is 239 Pu, where both ENDF/B-VIII.0 and JEFF-3.3 correctly compute k eff of the Jezebel critical assembly, but the individual contributions from each reaction are vastly different. To help resolve this specific case, the Experiments Underpinned by Computational Learning for Improvements in Nuclear Data (EUCLID) project used machine learning to design a set of experiments to help resolve the compensating errors in 239 Pu. A total of six responses were measured during the experimental campaign, which constrain the data in ways that k eff alone cannot and will be used for adjustment of the nuclear data. One of these responses is the neutron leakage spectrum, which recent work has shown to be useful for constraining the prompt fission neutron spectrum and inelastic scattering. The neutron leakage spectra were measured utilizing a 3 in. right cylinder EJ-301D detector. The measured signal in the detector was deconvoluted using spectrum unfolding techniques, which are presented and compared to simulations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Fast decay of classification error in variational quantum circuits

Variational quantum circuits (VQCs) have shown great potential in near-term applications. However, the discriminative power of a VQC, in connection to its circuit architecture and depth, is not understood. To unleash the genuine discriminative power of a VQC, we propose a VQC system with the optimal classical post-processing—maximum-likelihood estimation on measuring all VQC output qubits. Via extensive numerical simulations, we find that the error of VQC quantum data classification typically decays exponentially with the circuit depth, when the VQC architecture is extensive—the number of gates does not shrink with the circuit depth. This fast error suppression ends at the saturation towards the ultimate Helstrom limit of quantum state discrimination. On the other hand, non-extensive VQCs such as quantum convolutional neural networks are sub-optimal and fail to achieve the Helstrom limit, demonstrating a trade-off between ansatz complexity and classification performance in general. To achieve the best performance for a given VQC, the optimal classical post-processing is crucial even for a binary classification problem. To simplify VQCs for near-term implementations, we find that utilizing the symmetry of the input properly can improve the performance, while oversimplification can lead to degradation.

Zhang, Bingzhi↗
DOE OSTI2021

JWST Noise Floor. II. Systematic Error Sources in JWST NIRCam Time Series

The James Webb Space Telescope (JWST) holds great promise for characterizing atmospheres of transiting exoplanets, potentially providing insights into Earth-sized planets within the habitable zones of M-dwarf host stars if photon-limited performance can be achieved. Here, we discuss the systematic error sources that are expected to be present in grism time-series observations with the NIRCam instrument. We find that pointing jitter and high-gain antenna moves in addition to the detectors’ subpixel crosshatch patterns will produce relatively small variations (less than 6 parts per million, ppm). The time-dependent aperture losses due to thermal instabilities in the optics can also be kept to below 2 ppm. To achieve these low noise values, it is important to employ a sufficiently large (more than 11) extraction aperture. Persistence due to charge-trapping will have a minor (less than 3 ppm) effect on the time series 20 minutes into an exposure and is expected to play a much smaller role than it does for the Hubble Space Telescope WFC3 detectors. We expect detector temperature fluctuations to contribute less than 3 ppm. In total, our estimated noise floor from known systematic error sources is only 9 ppm per visit. We urge caution, however, because unknown systematic error sources could be present in flight and will only be measurable on astrophysical sources such as quiescent stars. We find that reciprocity failure may introduce a perennial instrument offset at the 40 ppm level, so corrections may be needed when a multi-instrument multi-observatory spectrum is stitched together over wide wavelength ranges.

47 OTHER INSTRUMENTATION↗