SEARCH · Engineering Papers

Results for “linear stability analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Numerical simulation of transitional flow

The applicability of active control of transition by periodic suction-blowing is investigated via direct simulations of the Navier-Stokes equations. The time-evolution of finite-amplitude disturbances in plane channel flow is compared in detail with and without control. The analysis indicates that, for relatively small three-dimensional amplitudes, a two-dimensional control effectively reduces disturbance growth rates even for linearly unstable Reynolds numbers. After the flow goes through secondary instability, three-dimensional control seems necessary to stabilize the flow. An investigation of the temperature field suggests that passive temperature contamination is operative to reflect the flow dynamics during transition.

Biringen, Sedat↗

NASA NTRS1988

Influence of heating rate on the condensational instability

Analysis and numerical simulation are used to determine the effect that various heating rates have on the linear and nonlinear evolution of a typical plasma within a solar magnetic flux tube subject to the condensational instability. It is found that linear stability depends strongly on the heating rate. The results of numerical simulations of the nonlinear evolution of the condensational instability in a solar magnetic flux tube are presented. Different heating rates lead to quite different nonlinear evolutions, as evidenced by the behavior of the global internal energy.

Dahlburg, R. B.↗

NASA NTRS1991

Instability of multi-layer fluid configurations in the presence of time-dependent accelerations in a microgravity environment

The increasing number of research opportunities in a microgravity environment will benefit not only fundamental studies in fluid dynamics, but also technological applications such as those involving materials processing. In particular, fluid configurations which involve fluid-fluid interfaces would occur in a variety of experimental investigations. This work investigates the stability of a configuration involving fluid-fluid interfaces in the presence of a time-dependent forcing. Both periodic (g-jitter) and nonperiodic accelerations are considered. The fluid configuration is multilayered, and infinite in extent. The analysis is linear and inviscid, and the acceleration vector is oriented perpendicular to each interface. A Floquet analysis is employed in the case of the periodic forcing. In the problem of nonperiodic forcing, the resulting system of equations are integrated in time. Specific nondimensional parameters appear in each problem. The configuration behavior is investigated for a range of parameter values.

Lyell, M. J.↗

NASA NTRS1988

Attitude Determination Error Analysis System (ADEAS) mathematical specifications document

The mathematical specifications of Release 4.0 of the Attitude Determination Error Analysis System (ADEAS), which provides a general-purpose linear error analysis capability for various spacecraft attitude geometries and determination processes, are presented. The analytical basis of the system is presented. The analytical basis of the system is presented, and detailed equations are provided for both three-axis-stabilized and spin-stabilized attitude sensor models.

Nicholson, Mark↗

NASA NTRS1995

Combustion-acoustic stability analysis for premixed gas turbine combustors

Lean, prevaporized, premixed combustors are susceptible to combustion-acoustic instabilities. A model was developed to predict eigenvalues of axial modes for combustion-acoustic interactions in a premixed combustor. This work extends previous work by including variable area and detailed chemical kinetics mechanisms, using the code LSENS. Thus the acoustic equations could be integrated through the flame zone. Linear perturbations were made of the continuity, momentum, energy, chemical species, and state equations. The qualitative accuracy of our approach was checked by examining its predictions for various unsteady heat release rate models. Perturbations in fuel flow rate are currently being added to the model.

Darling, Douglas↗

NASA NTRS2010

A Spectral Lyapunov Function for Exponentially Stable LTV Systems

This paper presents the formulation of a Lyapunov function for an exponentially stable linear timevarying (LTV) system using a well-defined PD-spectrum and the associated PD-eigenvectors. It provides a bridge between the first and second methods of Lyapunov for stability assessment, and will find significant applications in the analysis and control law design for LTV systems and linearizable nonlinear time-varying systems.

Zhu, J. Jim↗

NASA NTRS1981

A multiloop generalization of the circle criterion for stability margin analysis

In order to provide a theoretical tool well suited for use in characterizing the stability margins (e.g., gain and phase margins) of multiloop feedback systems, multiloop input-output stability results generalizing the circle stability criterion are considered. Generalized conic sectors with 'centers' and 'radii' determined by linear dynamical operators are employed to enable an engineer to specify the stability margins which he desires as a frequency-dependent convex set of modeling errors (including nonlinearities, gain variations, and phase variations) which the system must be able to tolerate in each feedback loop without instability. The resulting stability criterion gives sufficient conditions for closed-loop stability in the presence of such frequency-dependent modeling errors, even when the modeling errors occur simultaneously in all loops.

Safonov, M. G.↗

DOE OSTI2020

The Adjoint Petrov–Galerkin method for non-linear model reduction

Here, we formulate a new projection-based reduced-order modeling technique for non-linear dynamical systems. The proposed technique, which we refer to as the Adjoint Petrov–Galerkin (APG) method, is derived by decomposing the generalized coordinates of a dynamical system into a resolved coarse-scale set and an unresolved fine-scale set. A Markovian finite memory assumption within the Mori–Zwanzig formalism is then used to develop a reduced-order representation of the coarse scales. This procedure leads to a closed reduced-order model that displays commonalities with the adjoint stabilization method used in finite elements. The formulation is shown to be equivalent to a Petrov–Galerkin method with a non-linear, time-varying test basis, thus sharing some similarities with the Least-Squares Petrov–Galerkin method. Theoretical analysis examining a priori error bounds and computational cost is presented. Numerical experiments on the compressible Navier–Stokes equations demonstrate that the proposed method can lead to improvements in numerical accuracy, robustness, and computational efficiency over the Galerkin method on problems of practical interest. Improvements in numerical accuracy and computational efficiency over the Least-Squares Petrov–Galerkin method are observed in most cases.

42 ENGINEERING↗

NASA NTRS1975

Passive three-axis stabilization of the Long Duration Exposure Facility

This paper presents an analysis of the attitude dynamics of the Long Duration Exposure Facility (LDEF). LDEF is a large cylindrical gravity gradient stabilized earth satellite which is planned to be delivered to a 270-n mi circular orbit by the space shuttle. The fundamental linear stability, capture requirements, and pitch bias constraints generated by the Garber instability are discussed. Numerical simulations, based on the full nonlinear equations for the coupled orbital and attitude motion of the vehicle and the viscous magnetic damper, show stable behavior of the spacecraft and a damping time constant of 30 to 70 orbits.

Huckins, E. K., III↗

NASA NTRS1987

Dual laser gyro test program

This paper addresses the results of a comparative test evaluation of two similar-sized but otherwise dissimilar ring laser gyroscopes (RLG's). Both units were tested side by side, with the input axes (IA's) parallel, on the same test table. This report describes the rationale and design factors considered important to the test objectives. Emphasis was placed upon the evaluation of the scale factor (SF) linearity, drift rate stability (short term and long term), and derived rate. Conclusions drawn were (1) that dual operation had an observable but insignificant effect on the test results, (2) that the benefits of dual operation outweighed the additional design and analysis efforts required at the outset of the program, and (3) that the performance characteristics of the two test articles were significantly different. The differences between the two test articles (1) led to suggestions which could direct one vendor toward obtaining improved performance and (2) resulted in the creation of a conceptually new method (DELTA TIME-COUNT histogram) for quickly assessing the quality of laser gyros (or any digital sensor device for that matter).

Jones, Malcolm E.↗

NASA NTRS1997

An Experimental Investigation on the Static Equilibria and Dynamics of Liquid Bridges

A liquid bridge is a volume of liquid held between two or more solid supports. In the case of small disk supports with a sharp edge, the contact line between the bridge and the support disk will be anchored along the edge of the disk. For these cases the solid presents a geometrical singularity and the contact angle is indeterminate within a given range. This dissertation presents research conducted on liquid bridges with anchored contact lines. The three major topics covered are: determining the role of support geometry on static equilibria, liquid bridge dynamical behavior, and forces exerted by a liquid bridge on a support structure. The work was primarily experimental and conducted in a "Plateau tank" that allowed for the simulation of equivalent low-gravity conditions. The main thrust of the experimental work involved the use of a high resolution optical measurement system for imaging the dynamic zone shape, measurement of the static and dynamic contact angles and non-invasive analysis of excited surface modes. The liquid bridge was manipulated by computer controlled linear actuators which allowed precise control over the physical characteristics of the bridge. Experiments have been carried out to locate a bifurcation point along the maximum volume axisymmetric stability margin. Below the critical slenderness the bifurcation from an axisymmetric to a stable nonaxisymmetric configuration is supercritical. However, above this critical slenderness, the bifurcation is subcritical. A series of experiments analyzed the effect on axisymmetric bridge stability by using support disks of different radii, The shape behavior as transition points were approached, as well as the limiting case of a vanishing support radius was investigated. Experiments were performed to determine the resonant frequencies of axisymmetric bridges subject to lateral vibrations. Anomolous results led to a series of experiments to characterize nonlinearities present in the dynamic bridge shape. Finally, an attempt was made to experimentally measure the force exerted by the bridge on the lower support disk. This was done through use of a force balance apparatus. Particular attention was paid to the behavior of the bridge as the minimum volume stability limit was approached.

Resnick, Andrew Howard↗

NASA NTRS1962

DEVELOPMENT OF DESIGN STRENGTH LEVELS FOR THE ELASTIC STABILITY OF MONOCOQUE CONES UNDER AXIAL COMPRESSION

Design relationships have been derived for the determination of elastic buckling strength levels for unpressurized monocoque truncated cones under axial compression. Theoretical implications have been considered in the establishment of a semi-empirical analysis leading to the development of probability based design expressions. Data from 170 tests by various investigators were statistically evaluated for the expected mean, 90%, and 99% probability strength levels. Dispersion of data was found to be slightly less than that of monocoque cylinders. Non-linear effects of radius to thickness ratio or strength deterioration with length to radius ratio were not discernible.

AXIAL COMPRESSION↗

NASA NTRS1991

Flight experiments measuring boundary-layer disturbances in laminar flow and correlation with stability analysis

Flight test results are reported from an experiment designed to study the detailed growth of disturbances in the laminar boundary layer. A gloved wing section incorporating closely-spaced flush-mounted streamwise-located instrumentation for measuring instability frequencies and amplitude growths as well as pressure distributions was used. The growth of Tollmien-Schlichting (T-S) and crossflow instabilities is predicted by the linear e exp n method and compared to the measured boundary-layer disturbance frequencies. The predictions showed good agreement with the measured data. The results exhibited fair agreement with previous n(T-S) and n(CF) flight correlations for several of the conditions analyzed. It is inferred from the high n(T-S) values for these data that moderately swept wings at compressible speeds can withstand higher combinations of n(T-S) and n(CF) values and still remain laminar than previously thought.

Lee, Cynthia C.↗

NASA NTRS1975

Analysis of longitudinal pilot-induced oscillation tendencies of YF-12 aircraft

Aircraft flight and ground tests and simulator studies were conducted to explore pilot-induced oscillation tendencies. Linear and nonlinear calculations of the integrated flight control system's characteristics were made to analyze and predict the system's performance and stability. The investigations showed that the small-amplitude PIO tendency was caused by the interaction of the pilot with a combination of the aircraft's short-period poles and the structural first bending mode zeros. It was found that the large-amplitude PIO's were triggered by abrupt corrective control actions by the pilot, which caused the stability augmentation system servo to position and rate limit. The saturation in turn caused additional phase lag, further increasing the tendency of the overall system to sustain a PIO.

Smith, J. W.↗

DOE OSTI2025

Understanding the Role of Hydroxyl Functionalization in Linear Poly(Ethylenimine) for Oxidation‐Resistant Direct Air Capture of CO 2

Aminopolymer-based adsorbents are a prominent class of materials being used for direct air capture of CO 2 at the industrial scale. However, improving their working lifetime, specifically by increasing their resilience to oxidative degradation, remains an ongoing challenge. Toward this end, functionalization of aminopolymers with non-amine functionalities such as hydroxyls has emerged in recent years as a promising strategy toward improving adsorbent lifetime. Although there is a growing body of work demonstrating the effectiveness of this approach and investigating the origin of this improved stability, studies to date have primarily focused on branched aminopolymer systems such as branched poly(ethylenimine). In this work, hydroxyl-functionalized linear poly(ethylenimine) is used to continue to probe the underlying protective mechanism of this strategy. A combination of thermogravimetric analysis, NMR relaxometry, differential scanning calorimetry, and computational simulations is used to better understand the relationship between the extent of chemical functionalization, physical properties, and adsorbent performance.

amine-based adsorbent↗

DOE OSTI2024

Electron Glass Phase with Resilient Zhang-Rice Singlets in LiCu 3 ⁢O 3

LiCu 3 ⁢O 3 is an antiferromagnetic mixed valence cuprate where trilayers of edge-sharing Cu(II)O (3⁢d 9 ) are sandwiched in between planes of Cu(I) (3⁢d 10 ) ions, with Li stochastically substituting Cu(II). Angle-resolved photoemission spectroscopy (ARPES) and density functional theory reveal two insulating electronic subsystems that are segregated in spite of sharing common oxygen atoms: a Cu d z 2 /O p z derived valence band (VB) dispersing on the Cu(I) plane, and a Cu 3⁢d x 2 -y 2 /O 2⁢p x,y derived Zhang-Rice singlet (ZRS) band dispersing on the Cu(II)O planes. First-principle analysis shows the Li substitution to stabilize the insulating ground state, but only if antiferromagnetic correlations are present. Li further induces substitutional disorder and a 2D electron glass behavior in charge transport, reflected in a large 530 meV Coulomb gap and a linear suppression of VB spectral weight at E F that is observed by ARPES. Surprisingly, the disorder leaves the Cu(II)-derived ZRS largely unaffected. Finally, this indicates a local segregation of Li and Cu atoms onto the two separate corner-sharing Cu⁡(II)⁢O 2 sub-lattices of the edge-sharing Cu(II)O planes, and highlights the ubiquitous resilience of the entangled two hole ZRS entity against impurity scattering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1974

The structure and circulation of the deep Venus atmosphere

A simple model for the structure of a nonrotating Hadley regime in an atmosphere with large thermal inertia is developed. The radiative fluxes are estimated by using a linearization about the radiative equilibrium state, and the dynamical fluxes are estimated by using scaling analysis. The requirement that differential heating by these fluxes be in balance in both the meridional and vertical directions leads to two equations for the mean static stability and meridional temperature contrast. The solution depends on two parameters: the strength of the radiative heating, as measured by the static stability of the radiative equilibrium state; and the ratio of the time it takes an external gravity wave to traverse the atmosphere to the time it would take the atmosphere to cool off radiatively. It is shown that it is not necessary to invoke convection to explain the approximate adiabatic lapse rate in the Venus atmosphere, but a greenhouse effect is necessary to explain the high surface temperatures.

Stone, P. H.↗

NASA NTRS1976

Theoretical evaluation of rigid baffles in the suppression of combustion instability

An analytical technique for the prediction of the effects of rigid baffles on the stability of liquid propellant combustors is presented. This analysis employs both two and three dimensional combustor models characterized by concentrated combustion sources at the chamber injector and a constant Mach number nozzle. An eigenfunction-matching method is used to solve the linearized partial differential equations describing the unsteady flow field for both models. Boundary layer corrections to this unsteady flow are in a mechanical energy dissipation model to evaluate viscous and turbulence effects within the flow. An integral instability relationship is then employed to predict the decay rate of the oscillations. Results of this analysis agree qualitatively with experimental observations and show that sufficient dissipation exists to indicate that the proper mechanism of baffle damping is a fluid dynamic loss. The response of the dissipation model to varying baffle blade length, mean flow Mach number, oscillation amplitude, baffle configuration, and oscillation mode is examined.

Combustion instability↗