SEARCH · Engineering Papers

Results for “heat transfer coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Analytical and experimental spur gear tooth temperature as affected by operating variables

A gear tooth temperature analysis was performed using a finite element method combined with a calculated heat input, calculated oil jet impingement depth, and estimated heat transfer coefficients. Experimental measurements of gear tooth average surface temperatures and instanteous surface temperatures were made with a fast response infrared radiometric microscope. Increased oil jet pressure had a significant effect on both average and peak surface temperatures at both high load and speeds. Increasing the speed at constant load and increasing the load at constant speed causes a significant rise in average and peak surface temperatures of gear teeth. The oil jet pressure required for adequate cooling at high speed and load conditions must be high enough to get full depth penetration of the teeth. Calculated and experimental results were in good agreement with high oil jet penetration but showed poor agreement with low oil jet penetration depth.

Townsend, D. P.↗

NASA NTRS1980

Convective heating of solid propellant during ignition

A pattern search optimization procedure is used to deduce from test data on the solid rocket boosters of the Space Shuttle the convective heat transfer coefficients between the igniter and main motor combustion gases and the surface of the solid propellant by utilizing a spatial and temporal ignition transient analysis. The 'best' convective coefficients are found which will minimize the overall deviation of the analytical prediction from the ignition transient test data. Computationally, this is achieved by treating the motor in such a way that only four optimization variables must be determined. The resulting coefficients greatly improve the prediction capabilities of the ignition transient analysis for the Space Shuttle SRM.

Murph, J. E.↗

NASA NTRS1980

Vapor chambers for an atmospheric cloud physics laboratory

The methanol/stainless steel vapor chambers (flat-plate heat pipes) discussed in this paper were developed for use in spaceborne atmospheric cloud chambers. This application imposed stringent thermal and mechanical requirements on the design. Flatness, low thermal mass, vibration, and structural integrity requirements were achieved in addition to precision temperature uniformity and thermal transport. Heat transfer coefficients on the order of 0.34 to 0.40 W/sq cm -C were measured. The vapor chambers are capable of transporting 170 W-cm per cm of width in either the axial or side-to-side direction.

Fleischman, G. L.↗

NASA NTRS1980

Full-coverage film cooling. I - Comparison of heat transfer data for three injection angles

Wind tunnel experiments were carried out at Stanford between 1971 and 1977 to study the heat transfer characteristics of full-coverage film cooled surfaces with three geometries; normal-, 30 deg slant-, and 30 deg x 45 deg compound-angled injection. A flat full-coverage section and downstream recovery section comprised the heat transfer system. The experimental objectives were to determine, for each geometry, the effects on surface heat flux of injection blowing ratio, injection temperature ratio, and upstream initial conditions. Spanwise-averaged Stanton numbers were measured for blowing ratios from 0 to 1.3, and for two values of injection temperature at each blowing ratio. The heat transfer coefficient was defined on the basis of a mainstream-to-wall temperature difference. Initial momentum and enthalpy thickness Reynolds numbers were varied from 500 to about 3000.

Crawford, M. E.↗

NASA NTRS1980

Analytical and experimental spur gear tooth temperature as affected by operating variables

A gear tooth temperature analysis was performed using a finite element method combined with a calculated heat input, calculated oil jet impingement depth, and estimated heat transfer coefficients. Experimental measurements of gear tooth average surface temperatures and instantaneous surface temperatures were made with a fast response infrared radiometric microscope. Increased oil jet pressure had a significant effect on both average and peak surface temperatures at both high load and speeds. Increasing the speed at constant load and increasing the load at constant speed causes a significant rise in average and peak surface temperatures of gear teeth. The oil jet pressure required for adequate cooling at high speed and load conditions must be high enough to get full depth penetration of the teeth. Calculated and experimental results were in good agreement with high oil jet penetration but showed poor agreement with low oil jet penetration depth.

Townsend, D. P.↗

NASA NTRS1981

Evaluation of a method for heat transfer measurements and thermal visualization using a composite of a heater element and liquid crystals

Commercially available elements of a composite consisting of a plastic sheet coated with liquid crystal, another sheet with a thin layer of a conducting material (gold or carbon), and copper bus bar strips were evaluated and found to provide a simple, convenient, accurate, and low-cost measuring device for use in heat transfer research. The particular feature of the composite is its ability to obtain local heat transfer coefficients and isotherm patterns that provide visual evaluation of the thermal performances of turbine blade cooling configurations. Examples of the use of the composite are presented.

Hippensteele, S. A.↗

NASA NTRS1981

Numerical solution of supersonic viscous flow over blunt delta wings

A general parabolized Navier-Stokes code has been developed to compute the steady supersonic viscous flow around arbitrary body shapes at high angles of attack. A nonorthogonal three-dimensional coordinate frame permits the code to march with solution surfaces which are the most appropriate. The code has been used to calculate the laminar flow over a slab delta wing with 70 deg sweep at angles of attack up to 41.5 deg and Mach numbers of 6.8 and 9.6. The computed shock shapes, surface pressures and heat transfer coefficients are compared with experiment and show agreement.

Tannehill, J. C.↗

NASA NTRS1981

Heat transfer from a row of impinging jets to concave cylindrical surfaces

Starting from the first principles, and with one experimentally obtained parameter, an expression for stagnation heat transfer is derived, applicable to round, impinging jets. The results obtained with a row of air jets impinging on an electrically-heated surface in a small-scale setup characteristic of a typical turbine blade have been found compatible with the average heat transfer from a geometrically similar, steam-heated surface scaled up ten times, and comparable with the results of other investigators. These findings were linked to the flow fields likely to exist in the gas turbine blades, internally cooled by a row of round jets or a single jet of equivalent width. The magnitude of heat-transfer coefficients obtained here with impinging jets approaches that normally associated with forced convection of water and evaporative cooling.

Hrycak, P.↗

NASA NTRS1981

Streamwise flow and heat transfer distributions for jet array impingement with crossflow

Two-dimensional arrays of circular jets of air impinging on a heat transfer surface parallel to the jet orifice plate are considered. The air, after impingement, is constrained to exit in a single direction along the channel formed by the surface and the jet plate. The downstream jets are subjected to a crossflow originating from the upstream jets. Experimental and theoretical results obtained for streamwise distributions of jet and crossflow velocities are presented and compared. Measured Nusselt numbers resolved to one streamwise hole spacing are correlated with individual spanwise row jet Reynolds numbers and crossflow-to-jet velocity ratios. Correlations are presented for both inline and staggered hole patterns including effects of geometric parameters: streamwise hole spacing, spanwise hole spacing, and channel height, normalized by hole diameter. The physical mechanisms influencing heat transfer coefficients as a function of flow distribution and geometric parameters are also discussed.

Florschuetz, L. W.↗

NASA NTRS1981

Some modifications to, and operational experiences with, the two-dimensional, finite-difference, boundary-layer code, STAN5

The two-dimensional, finite-difference boundary-layer code, STAN5, is the primary tool used at the NASA-Lewis Research Center for predicting turbine blade gas-side heat-transfer coefficients. A number of modifications have been made to the program to enhance its usefulness for these calculations. Experience in using STAN5 has identified some problems in the program that can be treated through program input, without modifying the program. These include the presence of a small separation bubble near the leading edge, and the effect of full-coverage film cooling on transition to turbulence. Some of the techniques used to treat these problems are described.

Gaugler, R. E.↗

NASA NTRS1981

Evaluation of a method for heat transfer measurements and thermal visualization using a composite of a heater element and liquid crystals

Hippensteele, S. A.↗

NASA NTRS1957

Investigation of Heat Transfer from a Stationary and Rotating Conical Forebody

The convective heat transfer from the surface of a conical forebody having a hemispherical nose, an included angle of approximately 30 deg, and. a maximum diameter of 18.9 inches was investigated in a wind tunnel for both stationary and. rotating operation. The range of test conditions included free-stream velocities up to 400 feet per second, rotational speeds up to 1200 rpm, and. angles of attack of 0 deg and 6 deg. Both a uniform surface temperature and a uniform heater input power density were used. The Nusselt-Reynolds number relations provided good correlation of the heat-transfer data for the complete operating range at 0 deg angle of attack with and without spinner rotation, and for 6deg angle of attack with rotation. Rotational speeds up to 1200 rpm had no apparent effect on the heat-transfer characteristics of the spinner. The results obtained at 6 deg angle of attack with rotation were essentially the same as those obtained at 0 deg angle of attack without rotation. The experimental heat-transfer characteristics in the turbulent flow region were consistently in closer agreement with the results predicted for a two-dimensional body than with those predicted. for a cone. For stationary operation at 60 angle of attack, the measured heat-transfer coefficients in the turbulent flow region were from 6 to 13 percent greater on the lower surface (windward. side) than on the upper surface (sheltered side) for corresponding surface locations. The spinner-nose geometry appeared to cause early boundary-layer transition. Transition was initiated at a fairly constant Reynolds number (based on surface distance from nose) of 8.0 x 10(exp 4). Transition was completed at Reynolds numbers less than 5.0 x 10(exp 5) for all conditions investigated.

Ruggeri, Robert S.↗

NASA NTRS1981

Jet impingement heat transfer enhancement for the GPU-3 Stirling engine

A computer model of the combustion-gas-side heat transfer was developed to predict the effects of a jet impingement system and the possible range of improvements available. Using low temperature (315 C (600 F)) pretest data in an updated model, a high temperature silicon carbide jet impingement heat transfer system was designed and fabricated. The system model predicted that at the theoretical maximum limit, jet impingement enhanced heat transfer can: (1) reduce the flame temperature by 275 C (500 F); (2) reduce the exhaust temperature by 110 C (200 F); and (3) increase the overall heat into the working fluid by 10%, all for an increase in required pumping power of less than 0.5% of the engine power output. Initial tests on the GPU-3 Stirling engine at NASA-Lewis demonstrated that the jet impingement system increased the engine output power and efficiency by 5% - 8% with no measurable increase in pumping power. The overall heat transfer coefficient was increased by 65% for the maximum power point of the tests.

Johnson, D. C.↗

NASA NTRS1982

Rapid solidification of metallic particulates

In order to maximize the heat transfer coefficient the most important variable in rapid solidification is the powder particle size. The finer the particle size, the higher the solidification rate. Efforts to decrease the particle size diameter offer the greatest payoff in attained quench rate. The velocity of the liquid droplet in the atmosphere is the second most important variable. Unfortunately the choices of gas atmospheres are sharply limited both because of conductivity and cost. Nitrogen and argon stand out as the preferred gases, nitrogen where reactions are unimportant and argon where reaction with nitrogen may be important. In gas atomization, helium offers up to an order of magnitude increase in solidification rate over argon and nitrogen. By contrast, atomization in vacuum drops the quench rate several orders of magnitude.

Grant, N. J.↗

NASA NTRS1982

Sharp flat plate heat transfer in helium at Mach numbers of 22.8 to 86.8

Surface heat transfer rates were measured on a sharp flat plate at zero angle of attack with helium over a Mach number range of 22.8 to 86.8 in a hypersonic shock tunnel. The density and leading edge Knudsen numbers were varied to span the continuum to near free molecule regimes. The strong interaction parameter varied from 11 to 16,000 with leading edge Knudsen numbers from 0.56 to 17.1, respectively. For high unit Reynolds number the rate of change of the heat transfer coefficient with the strong interaction parameter agreed well with the strong interaction theory of Li and Nagamatsu (1953, 1955).

Nagamatsu, H. T.↗

NASA NTRS1982

Numerical solution of Space Shuttle Orbiter flow field

The supersonic, viscous laminar flow around the Space Shuttle Orbiter forebody has been computed with a parabolized Navier-Stokes code using a generalized coordinate transformation. The initial solution for the nose part of the Orbiter geometry was obtained with a three-dimensional time-dependent Navier-Stokes solver. It was necessary to employ a wind axis oriented coordinate system to obtain the initial solution with the time-dependent code. The generalized PNS technique used in this study allows the solution to be marched from the given initial data surface to any desired surface downstream. A grid point clustering scheme was employed to accurately describe the body shape by clustering points at the wing tip and at the wing body juncture. The computed heat transfer coefficients, pressure coefficients, and shock shapes are compared with the available experimental data for 0 degrees and 30 degrees angle of attack.

Venkatapathy, E.↗

NASA NTRS1982

Experimental and analytical determination of gear tooth temperatures with oil jet lubrication

Gear tooth average and instantaneous surface temperatures were measured with a fast response infrared radiometric microscope, while operating at arious speeds, loads and oil jet pressures. Increased oil jet pressure had a significant effect on both average and peak surface temperatures at all test conditions, increasing the speed at constant load and increasing the load at constant speed causes a significant rise in average and peak surface temperatures of gear teeth. A gear tooth temperature analysis was conducted by a finite element method combined with a calculated heat input and oil jet impingment depth with estimated heat transfer coefficients based on the experimental data. It is concluded that oil jet pressures required for adequate cooling at high load and speed conditions must be high enough to get full penetration depth of the teeth.

Townsend, D. P.↗

NASA NTRS1982

Jet array impingement flow distributions and heat transfer characteristics. Effects of initial crossflow and nonuniform array geometry

Two-dimensional arrays of circular air jets impinging on a heat transfer surface parallel to the jet orifice plate are considered. The jet flow, after impingement, is constrained to exit in a single direction along the channel formed by the jet orifice plate and the heat transfer surface. The configurations considered are intended to model those of interest in current and contemplated gas turbine airfoil midchord cooling applications. The effects of an initial crossflow which approaches the array through an upstream extension of the channel are considered. Flow distributions as well as heat transfer coefficients and adiabatic wall temperatures resolved to one streamwise hole spacing were measured as a function of the initial crossflow rate and temperature relative to the jet flow rate and temperature. Both Nusselt number profiles and dimensionless adiabatic wall temperature (effectiveness) profiles are presented and discussed. Special test results which show a significant reduction of jet orifice discharge coefficients owing to the effect of a confined crossflow are also presented, along with a flow distribution model which incorporates those effects. A nonuniform array flow distribution model is developed and validated.

Florschuetz, L. W.↗