Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fluid characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Computational Fluid Dynamics Study on the Effects of RATO Timing on the Scale Model Acoustic Test

The Scale Model Acoustic Test (SMAT) is a 5% scale test of the Space Launch System (SLS), which is currently being designed at Marshall Space Flight Center (MSFC). The purpose of this test is to characterize and understand a variety of acoustic phenomena that occur during the early portions of lift off, one being the overpressure environment that develops shortly after booster ignition. The SLS lift off configuration consists of four RS-25 liquid thrusters on the core stage, with two solid boosters connected to each side. Past experience with scale model testing at MSFC (in ER42), has shown that there is a delay in the ignition of the Rocket Assisted Take Off (RATO) motor, which is used as the 5% scale analog of the solid boosters, after the signal to ignite is given. This delay can range from 0 to 16.5ms. While this small of a delay maybe insignificant in the case of the full scale SLS, it can significantly alter the data obtained during the SMAT due to the much smaller geometry. The speed of sound of the air and combustion gas constituents is not scaled, and therefore the SMAT pressure waves propagate at approximately the same speed as occurs during full scale. However, the SMAT geometry is much smaller allowing the pressure waves to move down the exhaust duct, through the trench, and impact the vehicle model much faster than occurs at full scale. To better understand the effect of the RATO timing simultaneity on the SMAT IOP test data, a computational fluid dynamics (CFD) analysis was performed using the Loci/CHEM CFD software program. Five different timing offsets, based on RATO ignition delay statistics, were simulated. A variety of results and comparisons will be given, assessing the overall effect of RATO timing simultaneity on the SMAT overpressure environment.

Nielsen, Tanner↗
NASA NTRS2011

LES of a Jet Excited by the Localized Arc Filament Plasma Actuators

The fluid dynamics of a high-speed jet are governed by the instability waves that form in the free-shear boundary layer of the jet. Jet excitation manipulates the growth and saturation of particular instability waves to control the unsteady flow structures that characterize the energy cascade in the jet.The results may include jet noise mitigation or a reduction in the infrared signature of the jet. The Localized Arc Filament Plasma Actuators (LAFPA) have demonstrated the ability to excite a high-speed jets in laboratory experiments. Extending and optimizing this excitation technology, however, is a complex process that will require many tests and trials. Computational simulations can play an important role in understanding and optimizing this actuator technology for real-world applications. Previous research has focused on developing a suitable actuator model and coupling it with the appropriate computational fluid dynamics (CFD) methods using two-dimensional spatial flow approximations. This work is now extended to three-dimensions (3-D) in space. The actuator model is adapted to a series of discrete actuators and a 3-D LES simulation of an excited jet is run. The results are used to study the fluid dynamics near the actuator and in the jet plume.

Brown, Clifford A.↗
DOE OSTI2023

From Well Log to Formation Model: A Novel Laboratory Calibrated Methodology with Demonstration

This work demonstrates how the characterization and modeling of both elastic and creep properties are essential to describe zones in layered rock formations as either low-stress targets for stimulation or high-stress barriers to fracture growth. Prediction of fracture height is critical for designing stimulation operations in oil and gas wells. Ideally, fractures are placed in target zones which will produce hydrocarbons and should not propagate into zones expected to be unproductive or to produce unwanted fluids such as water which in turn must be treated and/or disposed. The essential task in designing stimulation plans is predicting which zones have low horizontal stresses and which will be high-stress barriers to fracture growth. Despite this importance, there are gaps in current knowledge and a complete workflow from laboratory characterization to a finite element model which includes time dependent rock deformation is required. While the research and methodology presented here also have application to CO 2or hydrogen storage, wastewater injection, and geothermal applications, the focus will be on hydrocarbon extraction. This thesis presents the results of a characterization-to-prediction workflow for the Caney shale, which is an emerging hydrocarbon resource in Oklahoma, USA. It begins with an investigation to enable critical evaluation of the Caney zonation into nominally “brittle” and “ductile” zones based on properties observed from well logs. It shows none of the zones are consistently “brittle” or “ductile” mechanical behavior based on the variety of definitions of these terms. However, the nominally ductile zones are weaker and more prone to creep. A laboratory investigation of samples including strength, elastic, and creep properties, is then used in a finite element model of stress evolution. The model includes both elastic deformation and viscoplastic creep. Results predict the least creep-prone layers to have the lowest horizontal stresses, therefore comprising hydraulic fracturing targets. The most creep-prone layers attain a horizontal stress similar to the vertical stress and therefore are predicted to be high stress barriers to hydraulic fracture stimulation. In addition to defining stimulation target intervals, the model shows how as tectonic strain rate increases, there is a transition from creep-dominated stresses to stresses dominated by elasticity.

Benge, Margaret↗
DOE OSTI2023

Time-lapse VSP integration and calibration of subsurface stress field utilizing machine learning approaches: A case study of the morrow B formation, FWU

This study aims to develop a methodology for calibrating subsurface stress changes through time-lapse vertical seismic profiling (VSP) integration. The selected study site is a region around the injector well located within Farnsworth field unit (FWU), where there is an ongoing CO 2 -enhanced oil recovery (EOR) operation. In our study, a site-specific rock physics model was created from extensive geological, geophysical, and geomechanical characterization through 3D seismic data, well logs, and core assessed as part of the 1D MEM conducted on the characterization well within the study area. Here, the Biot-Gassmann workflow was utilized to combine the rock physics and reservoir simulation outputs to determine the seismic velocity change due to fluid substitution. Modeled seismic velocities attributed to mean effective stress were determined from the geomechanical simulation outputs, and the stress-velocity relationship developed from ultrasonic seismic velocity measurements. A machine learning-assisted workflow comprised of an artificial neural network and a particle swarm optimizer (PSO) was utilized to minimize a penalty function created between the modeled seismic velocities and the observed time-lapse VSP dataset. The successful execution of this workflow has affirmed the suitability of acoustic time-lapse measurements for 4D-VSP geomechanical stress calibration pending measurable stress sensitivities within the anticipated effective stress changes and the availability of suitable and reliable datasets for petroelastic modeling. © 2023 Society of Chemical Industry and John Wiley & Sons, Ltd.

58 GEOSCIENCES↗
DOE OSTI2025

Numerical simulation of frost formation and heat transfer on fin-and-tube heat exchangers in turbulent cross-flow

Frost formation in fin-and-tube heat exchangers in turbulent cross-flow presents significant challenges in industrial refrigeration applications, affecting heat transfer efficiency and operational reliability. The purpose of this work is to investigate frost deposition and growth on a staggered bank of a fin-and-tube freezer coil under turbulent forced convection conditions. The focus here is on investigating conditions that closely replicate real-world scenarios in large walk-in industrial freezers. Using a direct numerical simulation approach, we examine the flow dynamics and thermal behaviour in the presence of frost, considering turbulent regimes characterized by a Reynolds number in the range 1050 ≤ R e D , avg ≤ 4800 , with the characteristic length being the outer diameter of the tube and the velocity being the bulk fluid velocity between the plates (fins). Computational fluid dynamics simulations are employed to resolve the interactions between turbulent airflow and the frost layer. Our approach incorporates a modified immersed boundary method and a slow-time acceleration technique to address the complex dynamic interface between the continuously evolving frost layer and the flowing air stream. Our findings indicate that frost forms more on the sides of the finned surfaces (plates) and less on the tubes themselves. This article is part of the theme issue ‘Heat and mass transfer in frost and ice’.

Science & Technology - Other Topics↗
DOE OSTI2022

A Brief Overview of Reactive Transport Codes Used in CO 2 Applications

Reactive transport modelling consists of computational and numerical models that describe the coupled physical, chemical, mechanical, and biological processes interacting with each other over a broad range of spatial and temporal scales. This report reviews some of the reactive transport codes available in the literature for carbon dioxide (CO 2 ) applications and can assist the scientific community with the applicability of each code to solve a specific problem. Approaches implemented in these codes can be categorized in three groups: (i) continuum-scale, (ii) pore-scale, and (iii) hybrid-scale approaches. Theoretical foundations, numerical implementations, and application examples using the models are described. In the continuum approach, flow and transport are formulated in terms of a representative control volume of the medium and coupled with geochemical reactions. The medium is characterized by bulk parameters such as porosity, permeability, or reactive surface area. In the pore-scale approach, each point of space in the pore network is occupied by either a fluid or solid phase. The pore-scale approach requires an exact knowledge of the spatial and temporal phase distribution. In the hybrid-scale approach, media are described by multiple characteristic length-scales, with some regions using a pore-scale approach while others used a continuum approach.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Heat Transfer of Supercritical Carbon Dioxide in 3D-Printed Tubes with Internal Ribs and Yttria Stabilized Zirconia Coating

This technical report describes measurements performed in NETL’s Heat Exchanger Experimental Test (HEET) facility using supercritical carbon dioxide as the working fluid. 3D printed tubes with internal ribs and yttria stabilized zirconia (YSZ) exterior coatings were employed in the heat exchanger. Heat transfer and friction factor enhancements from the internal ribs were characterized over a range of flow conditions. Additionally, the thermal resistance from the YSZ coating was characterized for both a freshly applied coating and a coating subjected to thermal aging.

36 MATERIALS SCIENCE↗
NASA NTRS2009

HART-II Acoustic Predictions using a Coupled CFD/CSD Method

This paper documents results to date from the Rotorcraft Acoustic Characterization and Mitigation activity under the NASA Subsonic Rotary Wing Project. The primary goal of this activity is to develop a NASA rotorcraft impulsive noise prediction capability which uses first principles fluid dynamics and structural dynamics. During this effort, elastic blade motion and co-processing capabilities have been included in a recent version of the computational fluid dynamics code (CFD). The CFD code is loosely coupled to computational structural dynamics (CSD) code using new interface codes. The CFD/CSD coupled solution is then used to compute impulsive noise on a plane under the rotor using the Ffowcs Williams-Hawkings solver. This code system is then applied to a range of cases from the Higher Harmonic Aeroacoustic Rotor Test II (HART-II) experiment. For all cases presented, the full experimental configuration (i.e., rotor and wind tunnel sting mount) are used in the coupled CFD/CSD solutions. Results show good correlation between measured and predicted loading and loading time derivative at the only measured radial station. A contributing factor for a typically seen loading mean-value offset between measured data and predictions data is examined. Impulsive noise predictions on the measured microphone plane under the rotor compare favorably with measured mid-frequency noise for all cases. Flow visualization of the BL and MN cases shows that vortex structures generated in the prediction method are consist with measurements. Future application of the prediction method is discussed.

Boyd, D. Douglas, Jr.↗
NASA NTRS2010

Quiet, Efficient Fans for Spaceflight: An Overview of NASA's Technology Development Plan

A Technology Development Plan to improve the aerodynamic and acoustic performance of spaceflight fans has been submitted to NASA s Exploration Technology Development Program. The plan describes a research program intended to make broader use of the technology developed at NASA Glenn to increase the efficiency and reduce the noise of aircraft engine fans. The goal is to develop a set of well-characterized government-owned fans nominally suited for spacecraft ventilation and cooling systems. NASA s Exploration Life Support community will identify design point conditions for the fans in this study. Computational Fluid Dynamics codes will be used in the design and analysis process. The fans will be built and used in a series of tests. Data from aerodynamic and acoustic performance tests will be used to validate performance predictions. These performance maps will also be entered into a database to help spaceflight fan system developers make informed design choices. Velocity measurements downstream of fan rotor blades and stator vanes will also be collected and used for code validation. Details of the fan design, analysis, and testing will be publicly reported. With access to fan geometry and test data, the small fan industry can independently evaluate design and analysis methods and work towards improvement.

Koch, L. Danielle↗
NASA NTRS2011

System Identification Applied to Dynamic CFD Simulation and Wind Tunnel Data

Demanding aerodynamic modeling requirements for military and civilian aircraft have provided impetus for researchers to improve computational and experimental techniques. Model validation is a key component for these research endeavors so this study is an initial effort to extend conventional time history comparisons by comparing model parameter estimates and their standard errors using system identification methods. An aerodynamic model of an aircraft performing one-degree-of-freedom roll oscillatory motion about its body axes is developed. The model includes linear aerodynamics and deficiency function parameters characterizing an unsteady effect. For estimation of unknown parameters two techniques, harmonic analysis and two-step linear regression, were applied to roll-oscillatory wind tunnel data and to computational fluid dynamics (CFD) simulated data. The model used for this study is a highly swept wing unmanned aerial combat vehicle. Differences in response prediction, parameters estimates, and standard errors are compared and discussed

Murphy, Patrick C.↗
NASA NTRSDate not supplied

Material Property Estimation in Thin Battery Components Using Guided Wave Measurement, Experimental Dispersion Curve Extraction and Finite Element Modeling

At NASA, we are investigating nondestructive evaluation (NDE) and structural health monitoring (SHM) techniques to detect precursors of thermal runaway failure in lithium metal based lithium ion batteries (LIB). The approach is centered on computational simulation models to guide inspection and aid in interpretation of results. Since lithium metal LIBs have combinations of solid and fluid-filled porous materials, obtaining accurate material properties is both challenging and critical for successful simulation of battery inspection. To this end, we investigated a multi-verification approach for material characterization of thin battery components. First, a laser Doppler vibrometer (LDV) was used to measure guided wave fields in thin (microns-thick) battery components subject to broadband excitation. The time-space wavefield data was converted to frequency-wave number data to extract guided wave dispersion curves. A data visualization and post processing graphics user interface (GUI) was developed at NASA to aid the data exploration and analysis. Due to the thinness of the samples, low frequency-thickness-product plate wave approximations allowed for the calculation of closed-form solutions for material elastic property estimation. These approximations were then verified by calculating the Lamb wave solutions using the previously obtained material properties. Finally, the estimated elastic material properties were implemented in a COMSOL simulation model, and dispersion curves were extracted from simulation results. The dispersion curves and derived material properties were then compared to the analysis results from the experimental data. These comparisons informed on the accuracy of the measured material properties and helped demonstrate the accuracy of the finite element analysis (FEA) computational models. This assessment will prove vital when we start simulating more complex multi-layer components and poroelastic media. This paper gives a brief background of the problem space, outlines the workflow for data analysis and verification, shows results from the workflow, and gives an overview of future plans for simulation of lithium metal LIB inspection.

Peter Juarez↗
DOE OSTI2021

Literature Data on Foam Fracturing Fluid

At the beginning of this project, the Temple team spent significant effort to collect data relevant to foam fracturing. More than 40 articles/reports were found in the open literature that reported the properties of aqueous foams under various testing conditions. The foam properties included viscosity and stability in terms of half-life, while were influenced by the foam quality, shear rate, temperature, pressure, as well as surfactants and additives used in making the foam base solutions. As a result, more than 1100 data points were collected, which are included in a master worksheet named "Literature data on Foam Fracturing Fluid". These data points are organized based on following parameters: 1. Literature source, including authors and publication year 2. Gaseous phase (e.g. CO2, N2) 3. Liquid phase (e.g. tap water, DI water, salt water) 4. Surfactants and their concentrations 6. Additives 7. Foam quality 8. Pressure 9. Temperature 10. Viscosity 11. Foam stability, which was characterized by its half-life: Half-life Foam study data base with data analysis was completed and a webpage is designed hosted on public server at https://surfactant-dashboard.herokuapp.com

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

Butterfly valve performance factors using the multiphysics object oriented simulation environment

Butterfly valves are typically used in nuclear reactors to control incompressible fluid flow with high inlet velocities. Performance factors for butterfly valves include the pressure drop across the valve and the loss coefficient from which hydrodynamic torque and flow coefficients can be computed. This work explores a computational fluid dynamics approach for butterfly valve performance factors using the open-source Multiphysics Object Oriented Simulation Environment (MOOSE) framework. While MOOSE is often used in the nuclear energy modeling and simulation community for simulations ranging from fuel characterization to heat pipe simulation, this work employs the MOOSE open-source Navier–Stokes solver capability for simulating butterfly valve performance factors and compares those to experimentally measured results from the Advanced Test Reactor at Idaho National Laboratory at Reynolds numbers in the order of 10 6 for the partially opened configuration. The MOOSE framework results are compared against experimentally measured butterfly valve performance factors across five valve opening angles using meshes with order 10 4 – 10 5 elements. This validation serves to enable MOOSE-based multiphysics simulations incorporating the open-source Navier–Stokes module.

97 - MATHEMATICS AND COMPUTING↗
NASA NTRS2003

Light Microscopy Module Fan Disturbance Characterized Through Microgravity Emissions Laboratory Testing

A Light Microscopy Module (LMM) is being engineered, designed, and developed at the NASA Glenn Research Center. The LMM is planned as a remotely controllable on-orbit microscope subrack facility, allowing flexible scheduling and control of physical science and biological science experiments within Glenn s Fluids Integrated Rack on the International Space Station. The LMM concept is a modified commercial research imaging light microscope with powerful laser-diagnostic hardware and interfaces, creating a one-of-a-kind, state-of-the-art microscopic research facility. The microscope will house several different objectives, corresponding to magnifications of 10, 40, 50, 63, and 100. Features of the LMM include high-resolution color video microscopy, brightfield, darkfield, phase contrast, differential interference contrast, spectrophotometry, and confocal microscopy combined in a single configuration. Also, laser tweezers are integrated with the diagnostics as a sample manipulation technique. As part of the development phase of the LMM, it was necessary to quantify the microgravity disturbances generated by the control box fan. Isolating the fan was deemed necessary to reduce the fan speed harmonic amplitudes and to eliminate any broadband disturbances across the 60- to 70-Hz and 160- to 170-Hz frequency ranges. The accelerations generated by a control box fan component of the LMM were measured in the Microgravity Emissions Laboratory (MEL). The MEL is a low-frequency measurement system developed to simulate and verify the on-orbit International Space Station (ISS) microgravity environment. The accelerations generated by various operating components of the ISS, if too large, could hinder the science performed onboard by disturbing the microgravity environment. The MEL facility gives customers a test-verified way of measuring their compliance with ISS limitations on vibratory disturbance levels. The facility is unique in that inertial forces in 6 degrees of freedom can be characterized simultaneously for an operating test article. Vibratory disturbance levels are measured for engineering or flight-level hardware following development from component to subassembly through the rack-level configuration. The MEL can measure accelerations as small as 10-7g, the accuracy needed to confirm compliance with ISS requirements.

McNelis, Anne M.↗
DOE OSTI2021

Oxygen enrichment combustion to reduce fossil energy consumption and emissions in hot rolling steel production

The reheating furnace operation in the hot mill is natural gas- and electricity-intensive. Oxygen enrichment combustion for reheating furnaces has been proposed to curb and replace natural gas use. In this study, heat transfer in steel slabs in the combustion environment of a push-type reheating furnace was simulated using a computational fluid dynamics (CFD) model. Two oxygen enrichment methods that optimized for performance were selected— a medium oxygen enrichment (MOE) case and an oxy-fuel (OF) case. A life cycle analysis (LCA) characterized the energy and emission profiles of an integrated iron and steel manufacturing process using the two oxygen enrichment cases for the hot mill. These conditions were evaluated for energy use and carbon intensity and compared with a baseline case. Results show that with oxygen enrichment, natural gas consumption can decrease by 19.6%–26.8%, total energy consumption (natural gas and electricity) can decrease by 15.1%–20.7% in the hot mill. Emissions of greenhouse gases can decrease by 11.1%–15.2% in the two optimized cases with 14%–27% reductions in regulated criteria pollutants (nitrogen oxides, carbon monoxide, particulate matter, volatile organic compounds, black carbon, organic carbon, and volatile organic carbons). There is a tradeoff between reducing natural gas consumption and increasing electricity demand from a life cycle perspective. Although the OF case resulted in higher energy- and emissions-related benefits, the MOE case showed the more desirable heat flux uniformity, which is key to maintaining product quality. The analysis suggests that oxygen enrichment in the reheating furnace process can have a significant impact on hot mill environmental performance and become a contributing factor in transitioning to low-carbon steel manufacturing.

36 MATERIALS SCIENCE↗
NASA NTRS1998

Suspension of SiC Powders in Allyhydridopolycarbosilane (AHPCS): Control of Rheology

Inert particulate fillers can be blended with preceramic polymers prior to infiltration of composite preforms to increase pyrolysis yield and decrease shrinkage, thus reducing the number of infiltration/ pyrolysis cycles required for densification. However, particulate filler loadings and concentration of added dispersants necessary to maintain low viscosity (< 0.50 N.s/sq m) slurries vary with the characteristics of the particular AHPCS polymer batch. These batch to batch variations occur with alterations in the synthesis process and method of allyl substitution, which in turn alter polymer structure and molecular weight distribution. A number of different polymer batches were characterized by NMR, GPC and thermal analysis, and the influence of polymer structure on rheology of filled systems determined. When the high molecular weight fraction increased to too great a level, suitably fluid slurries could no longer be attained.

Hurwitz, Frances I.↗
NASA NTRS1999

Large Eddy Simulation of a Forced Round Turbulent Buoyant Plume in Neutral Surroundings

Buoyant flows play an important role in various technological and environmental issues. For example, dispersal of pollutants, smoke, or volcano exhaust in the atmosphere, vertical motion of air, formation of clouds and other weather systems, and flows in cooling towers and fires are all determined primarily by buoyancy effects. The buoyancy force in such flows can originate from either a heat source or due to different densities between a fluid and its surroundings. Whatever the cause, the flow can be understood by studying the effects of the tight coupling between the thermal and the velocity fields since density differences can be characterized as temperature differences.

Basu, A. J.↗
NASA NTRS2003

Crystal Growth of ZnSe and Related Ternary Compound Semiconductors by Vapor Transport

The objective of the project is to determine the relative contributions of gravity-driven fluid flows to the compositional distribution, incorporation of impurities and defects, and deviation from stoichiometry observed in the crystals grown by vapor transport as results of buoyancy-driven convection and growth interface fluctuations caused by irregular fluid-flows. ZnSe and related ternary compounds, such as ZnSeS and ZnSeTe, were grown by vapor transport technique with real time in situ non-invasive monitoring techniques. The grown crystals were characterized extensively to correlate the grown crystal properties with the growth conditions. Significant effects of gravity vector orientation on the growth crystal morphology and point defect distribution were observed.

Source record↗