Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “diameter distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Meteoroid protection for the Comet Halley probe

The high closing speed of 57km/s between the spacecraft and Halley poses special problems in the design of the required meteoroid protection. A double wall structure with a total thickness equal to 0.1 to 1 times the diameter of the largest meteoroid encountered is sufficient to stop that meteoroid. However, the unusually high number of meteoroid impacts on the Halley probe will cause significant erosion of the outer wall so that failure of the second wall is more likely to occur from a small meteoroid passing through a previously created hole in the outer wall and then penetrating the second wall. Calculations of the shielding required based on this failure mode, show that a double wall structure must actually have a total thickness 1.2 to 7.3 times the diameter of the largest meteoroid encountered, depending on the size distribution of the meteoroids.

Humes, D.↗

Characterization of aerosols from eruptions of Mount St. Helens

Measurements of mass concentration and size distribution of aerosols from eruptions of Mount St. Helens as well as morphological and elemental analyses were obtained between 7 April and 7 August 1980. In situ measurements were made in early phreatic and later, minor phreatomagmatic eruption clouds near the vent of the volcano and in plumes injected into the stratosphere from the major eruptions of 18 and 25 May. The phreatic aerosol was characterized by an essentially monomodal size distribution dominated by silicate particles larger than 10 micrometers in diameter. The phreatomagmatic eruption cloud was multimodal; the large size mode consisted of silicate particles and the small size modes were made up of mixtures of sulfuric acid and silicate particles. The stratospheric aerosol from the main eruption exhibited a characteristic narrow single mode with particles less than 1 micrometer in diameter and nearly all of the mass made up of sulfuric acid droplets.

Chuan, R. L.↗

Far-infrared properties of dust in the reflection nebula NGC 7023

Thermal emission from dust in the reflection nebula NGC 7023 has been observed at wavelengths between 40 and 400 microns. The observed far-infrared emission comes from a region approximately 4 arcmin in diameter and shows spatial structure which correlates well with the distribution of reflected visible radiation. Temperature and optical depth maps indicate that the dust which emits the far-infrared radiation is heated by UV and visual radiation from the central star (HD 200775) and that the dust density increases steeply northwest of the star. The far-infrared data are not consistent with either the spherical or uniform slab geometries used in earlier analyses of optical observations. Comparisons of the far-infrared measurements with optical and UV measurements give a value between 2000 and 5000 for the ratio of extinction efficiency in the UV to that at 125 microns. This value is compared with the results of other observational studies and with theoretical grain models.

Whitcomb, S. E.↗

Experimental and theoretical deposition rates from salt-seeded combustion gases of a Mach 0.3 burner rig

Deposition rates on platinum-rhodium cylindrical collectors rotating in the cross streams of the combustion gases of a salt-seeded Mach 0.3 burner rig were determined. The collectors were internally air cooled so that their surface temperatures could be widely varied while they were exposed to constant combustion gas temperatures. The deposition rates were compared with those predicted by the chemically frozen boundary layer (CFBL) computer program, which is based on multicomponent vapor transport through the boundary layer. Excellent agreement was obtained between theory and experiment for the NaCl-seeded case, but the agreement lessened as the seed was changed to synthetic sea salt, NaNO3, and K2SO4, respectively, and was particularly poor in the case of Na2SO4. However, when inertial impaction was assumed to be the deposition mechanism for the Na2SO4 case, the predicted rates agreed well with the experimental rates. The former were calculated from a mean particle diameter that was derived from the measured intial droplet size distribution of the solution spray. Critical experiments showed that liquid phase deposits were blown off the smooth surface of the platinum-rhodium collectors by the aerodynamic shear forces of the high-velocity combustion gases but that rough or porous surfaces retained their liquid deposits.

Santoro, G. J.↗

Ode to gravity: Depth/diameter for fresh craters on Mercury

Opinions conflict over the role of surface gravity in shaping impact craters on Mercury. One view holds that the effects of g are evident in measurable aspects of crater form; other investigators find little or no evidence for g's geomorphic importance. Ambiguity in the role of g and other variables in cratering on Mercury stems largely from uncertainty in identifying major geomorphic contrasts and the crater sizes at which they occur. One of these, depth/diameter (d/D), undergoes a major change at the transition from simple (bowl shaped) to complex (peaks and terraces) crater interiors. Four least-squares d/D fits for fresh craters on Mercury were attemped. The results are inconsistent. The d/D data that should resolve previous shortcomings is presented. The revised d/D distributions for simple and complex craters, which intersect at a diameter of about 5 km, support the initial thesis that g substantially influences the form of Mercury's craters.

Pike, R. J.↗

Experimental investigation of shock-cell noise reduction for single-stream nozzles in simulated flight, comprehensive data report. Volume 3: Shadowgraph photos and facility description

A total of 142 shadowgraph photographs were taken on 43 different plumes that were distributed over the six nozzle configurations using the 9.5 inch diameter collimated light beam of the shadowgraph setup. Aerodynamic flow conditions of the shadowgraph test points, the location and identification of each of the photographs, and copies of the pictures are presented.

Yamamoto, K.↗

Environment definition, small particles, diameter less than or equal to 1 MM

The collection of particles of diameters one millimeter and less far outnumbers the larger particle distribution in orbit. These small particles cannot be tracked from ground based radar as can the larger debris, therefore, there is greater uncertainty in their properties. The population is growing from contributions due to collisions of larger debris, explosions, and aluminum oxide particles from solid rocket motors. The solid rocket motor contribution is the prominent growth parameter, and the input from Space Shuttle deployed upper stages will range between 50,000 and 100,000 pounds per year. The environment is important because of the different design problems that will be posed to the engineer and scientist. The emphasis shifts from catastrophe deign, probability versus exposure time, and tracking-avoidance, to a continuous degradation problem.

Source record↗

Performance characteristics of a new helical-channel microchannel plate

An advanced version of the 'helical-channel' microchannel plate (MCP) is presented. This MCP is composed of four channels per fiber with each channel having a diameter of 50 microns. The dynamic range, pulse-height distribution, and gain characteristics of this MCP are discussed. It is found that increasing the twist density of the channels makes it possible to increase the detection efficiency and further improve the suppression of ion-feedback providing a tighter saturated pulse-height distribution and improved high-voltage characteristics.

Slater, David C.↗

Release of liquid water from the Space Shuttle

Groundbased and onboard video images of a sunlit Shuttle Orbiter water dump are interpreted as showing that the continuous 1-mm-diameter liquid stream quickly breaks up in near-vacuum to form ice/snow particles of two characteristic sizes. Discrete large droplets are most evident in the close-in photographs, and unresolved submicron 'fog' from recondensation of overexpanded evaporated water appears to dominate the ground-telescope photographs of the 2.5 km long optically detectable trail. The mean diameter of the smaller particles was estimated from the spatial distribution of visible radiance using a model of their energy balance, (small) surface roughening as they sublime, and Mie scattering of pre-dawn sunlight. The results are consistent with those from recent space-tank simulations.

Pike, C. P.↗

Measurements of condensation nuclei in the Airborne Arctic Stratospheric Expedition - Observations of particle production in the polar vortex

The ER-2 Condensation Nucleus Counter (ER-2 CNC) was operated in the Airborne Arctic Stratospheric Expedition (AASE) in January and February 1989. The ER-2 CNC measures the mixing ratio of particles, CN, with diameters from approximately 0.02 to approximately 1 micron. The spatial distribution of CN in the Arctic polar vortex was found to resemble that measured in the Antarctic in the Spring of 1987. The vertical profile of CN in the vortex was lowered by subsidence. At altitudes above the minimum in the CN mixing ratio profile, CN mixing ratios correlated negatively with that of N2O, demonstrating new particle production. CN serve as nuclei in the formation of Polar Stratospheric Clouds (PSCs) and the concentration of CN can affect PSC properties.

Wilson, J. C.↗

Unsteady pressure loads in a generic high speed engine model

Unsteady pressure loads were measured along the top interior wall of a generic high-speed engine (GHSE) model undergoing performance tests in the combustion-Heated Scramjet Test Facility at the Langley Research Center. Flow to the model inlet was simulated at 72000 ft and a flight Mach number of 4. The inlet Mach number was 3.5 with a total temperature and pressure of 1640 R and 92 psia. The unsteady pressure loads were measured with 5 piezoresistive gages, recessed into the wall 4 to 12 gage diameters to reduce incident heat flux to the diaphragms, and distributed from the inlet to the combustor. Contributors to the unsteady pressure loads included boundary layer turbulence, combustion noise, and transients generated by unstart loads. Typical turbulent boundary layer rms pressures in the inlet ranged from 133 dB in the inlet to 181 dB in the combustor over the frequency range from 0 to 5 kHz. Downstream of the inlet exist, combustion noise was shown to dominate boundary layer turbulence noise at increased heat release rates. Noise levels in the isolator section increased by 15 dB when the fuel-air ratio was increased from 0.37 to 0.57 of the stoichiometric ratio. Transient pressure disturbances associated with engine unstarts were measured in the inlet and have an upstream propagation speed of about 7 ft/sec and pressure jumps of at least 3 psia.

Parrott, Tony L.↗

Continued investigation of LDEF's structural frame and thermal blankets by the Meteoroid and Debris Special Investigation Group

This report focuses on the data acquired by detailed examination of LDEF intercostals, 68 of which are now in possession of the Meteoroid and Debris Special Investigation Group (M&D SIG) at JSC. In addition, limited data will be presented for several small sections from the A0178 thermal control blankets that were examined/counted prior to being shipped to Principal Investigators (PI's) for scientific study. The data presented here are limited to measurements of crater and penetration-hole diameters and their frequency of occurrence which permits, yet also constrains, more model-dependent, interpretative efforts. Such efforts will focus on the conversion of crater and penetration-hole sizes to projectile diameters (and masses), on absolute particle fluxes, and on the distribution of particle-encounter velocities. These are all complex issues that presently cannot be pursued without making various assumptions which relate, in part, to crater-scaling relationships, and to assumed trajectories of natural and man-made particle populations in LEO that control the initial impact conditions.

See, Thomas H.↗

Crustal Magnetic Spectra from Correlated Sources on Mars

The spectral method for distinguishing crustal from core-source magnetic fields has been re-examined, modified and applied to both a comprehensive geomagnetic field model and an altitude normalized magnetic map of Mars. These observational spectra are fairly fitted by theoretical forms expected from certain elementary classes of magnetic sources. For Earth we found fields from a core radius 3512 +/- 64 km and a crust represented by a shell of random dipolar sources at radius 6367 +/- 14 km. For Mars we found only a field from a crust represented in the same way, but 46 +/- 10 km below the planetary menu radius. More realistic theoretical spectra, allowing for crustal thickness, oblateness and magnetization by a planet centered dipole, were derived and discussed, as were spectral effects of laterally correlated sources. The main effect of laterally correlated sources is to soften the spectrum at high degrees. We tend to over-estimate source shell depth when this is omitted. To include this effect simply size and magnetization distribution functions for extended sources are recast as a characteristic diameter and mean square magnetization amplitude for an ensemble of vertically magnetized spherical caps on a shell. For small caps, and at moderated degrees, the practical derivatives of the log-theoretical spectrum with respect to amplitude, shell radius, and cap diameter are approximately proportional to l, n, and -n **2, respectively. Separation of diameter from amplitude from layer thickness. Results from applications to observational spectra are discussed, noting that there are now several fine field models for Mars; moreover, the terrestrial magnetic spectrum at high degrees, as revised, updated with high precision Oerstad data, and upgrade with high resolution Champ data, appears softer than before.

Voorhies, Coerte V.↗

Propeller-Design Problems of High-Speed Airplanes, Special Report

It is shown that on the basis of existing high-speed airfoil data, propeller efficiencies appreciably in excess of 40% do not appear possible at speeds above 500 miles per hour at 20,000 feet. The assumption that present propeller-blade thicknesses cannot be reduced radically, is implied. Until the reliability and applicability of the airfoil data are established, this conclusion must not be regarded as infallible. Dive tests with airplanes equipped with thrust meters and torque meters are proposed to provide an urgently needed check. The design of high-speed propellers is dictated wholly by compressibility considerations. The blade width, thickness, and pitch distribution; also the airfoil sections, the lift coefficient, the propeller diameter, and rpm must all be adjusted if reasonable efficiencies are to be maintained at airplane speeds that are now being approached. Research is urgently needed on: 1) airfoils at subsonic, sonic, and supersonic speeds; 2) propellers at high forward speeds in wind tunnels; 3)propellers in free flight at high speeds; and 4) jet propulsion and related devices. The breakdown of propeller efficiency indicated by airfoil data, should serve as an incentive for accelerated research on jet propulsion. This device may extend the attainable speed of current airplanes to the neighborhood of 550 miles per hour at 20,000 feet.

Dickinson, H. B.↗

Multi-Parameter Scattering Sensor and Methods

Methods, detectors and systems detect particles and/or measure particle properties. According to one embodiment, a detector for detecting particles comprises: a sensor for receiving radiation scattered by an ensemble of particles; and a processor for determining a physical parameter for the detector, or an optimal detection angle or a bound for an optimal detection angle, for measuring at least one moment or integrated moment of the ensemble of particles, the physical parameter, or detection angle, or detection angle bound being determined based on one or more of properties (a) and/or (b) and/or (c) and/or (d) or ranges for one or more of properties (a) and/or (b) and/or (c) and/or (d), wherein (a)-(d) are the following: (a) is a wavelength of light incident on the particles, (b) is a count median diameter or other characteristic size parameter of the particle size distribution, (c) is a standard deviation or other characteristic width parameter of the particle size distribution, and (d) is a refractive index of particles.

Greenberg, Paul S.↗

A Study of Precipitation Mean Particle Size with the GPM Combined Radar-Radiometer Algorithm

The Global Precipitation Measurement (GPM) mission provides quantitative estimates of the mass-weighted mean diameter, Dm, a characteristic parameter of the precipitation particle size distribution (PSD). This study investigates the three-dimensional distribution of Dm retrieved by the GPM Combined Radar-Radiometer Algorithm (CORRA) using observations from GPM’s dual-frequency precipitation radar and microwave imager. We examine Dm in individual precipitation systems in different climate regimes and investigate a six-year global climatology. The vertical structure of Dm is demonstrated with cases of deep convection, frontal rain and snow, and stratocumulus light rain. The Dm values, detectable by GPM, range from appx 0.7 mm in stratocumulus precipitation to >3.5 mm in the ice layers of intense convection. Within the constraint of the 12-dBZ detectability threshold, the smallest climatological mean Dm (~ 0.8 mm) are found in the eastern oceans, and the largest values (~ 2 mm) occur above the melting levels in convection over land in summer. The standard deviation is generally < 0.45 mm below 6 km. Climate regimes are characterized with Dm annual/seasonal variations, its convective/stratiform components, and vertical variabilities (2-10 km). The US Central Plains and Argentina are associated with the largest Dm in a deep layer. Tropical Africa has larger Dm and standard deviation than Amazon. Large convective Dm occurs at high latitudes of Eurasia and North America in summer; the southern hemisphere high latitudes have shallower systems with smaller Dm. Oceanic storm tracks in both hemispheres have relatively large Dm, particularly for convective Dm in winter.

Mei Han↗

High-Resolution UV Holography Lens for Particle Size Distribution Measurements

A high-resolution UV holography relay lens, shown in Figure 1, has been developed for measuring particle size distributions down to 0.5 μm in a 12-mm-diameter by 5-mm-thick volume. This work has been selected by an independent judging panel and editors of R&D Magazine as a recipient of a 2009 R&D 100 Award. This award recognizes the 100 most technologically significant products introduced during the past year.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Statistical Uncertainty of Inhalation Dose Coefficients in Consequence Management: Propagated Dose Uncertainty in ICRP 66 Human Respiratory Tract Model

Reference inhalation dose models rely on deterministic biokinetics and reference computational phantoms, limiting their applicability to the variability present in population-specific exposures encountered in emergency response scenarios. Here, this study introduces REDCAL, a Python-based computational framework developed to propagate uncertainty in inhalation dose coefficients using the International Commission on Radiological Protection (ICRP) Publication 66 Human Respiratory Tract Model. REDCAL integrates ICRP deposition and clearance models, systemic biokinetics, and governing physics principles, and leverages Sandia National Laboratories’ Dakota toolkit for uncertainty quantification via Latin Hypercube Sampling. REDCAL was validated against DCAL, with biokinetic retention results differing by less than 1% and effective dose coefficients by less than 2% across all tested radionuclides. Stochastic sampling introduced variability in dose coefficients, with geometric standard deviations (GSD) in committed effective dose coefficients (CEDC) ranging from 1.0 to 1.5, based on lognormal distribution fits. Analysis demonstrated that variations in the activity median aerodynamic diameter (AMAD) notably influenced the computed CEDC values. Smaller particles (<1 µm) increased doses by 20–30% due to deeper lung deposition and prolonged retention for alpha emitting radionuclides, such as 241 Am and 239 Pu. Radionuclides with fast clearance, such as 133 I, demonstrated a dose reduction exceeding 50%, as AMAD increased beyond 5 µm due to upper airway deposition and rapid mucociliary clearance. The greatest GSD among the radionuclides reported in this study was for 241 Am. In most cases, the largest GSDs in the CEDC were associated with larger particle sizes, an expected outcome, as ICRP Publication 66 defines GSD in particle size as a function of AMAD, resulting in an extended tail of the lognormal distribution. The findings support improved inhalation dose assessments and enhance consequence management strategies for the U.S. Federal Radiological Monitoring and Assessment Center by quantifying uncertainty in dose coefficients and strengthening decision-making for emergency response scenarios.

Biokinetic Modeling↗