Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “computer system performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Land landing couch dynamics computer program

Computer programs perform landing stability studies of mechanical impact system designs for advanced spacecraft. The programs consider variation in spacecraft vertical and horizontal velocity, attitude and orientation, shock strut load-stroke characteristics, and ground coefficient of friction.

Herting, D. N.↗

Voter-comparator-switch optimization study

The design optimization and simulation effort of the voter-comparator switch (VCS) element are described. The VCS is an adaptive voter element that performs failure detection and reconfiguration function in a computer system designed to tolerate any three single failures in a fail operational fail operational fail safe manner. Detailed logic equations were developed and the design was evaluated and refined using a logic level fault simulator.

Jurison, J.↗

On the design of optimal input signals in system identification

The problem of designing optimal inputs in the identification of multi-input multi-output linear systems with unknown time-varying parameters is considered using a Bayesian approach. A sensitivity index gives a measure of performance for the closed-loop system inputs. The computation of the optimal closed-loop mappings is shown to be a nontrivial exercise in stochastic control with no analytic solution, but optimal open-loop and affine laws yield much more tractable problems. For time-invariant systems, the sensitivity index considered is shown to be equivalent to the trace of the (strictly positive definite) information matrix associated with the system. Numerical examples are given. A Kalman filter is used to estimate the parameters. A necessary condition for the Kalman filter not to diverge when applying linear feedback is also given.

Lopez-Toledo, A. A.↗

Simultaneous calculation of aircraft design loads and structural member sizes

A design process which accounts for the interaction between aerodynamic loads and changes in member sizes during sizing of aircraft structures is described. A simultaneous iteration procedure is used wherein both design loads and member sizes are updated during each cycle yielding converged, compatible loads and member sizes. A description is also given of a system of programs which incorporates this process using lifting surface theory to calculate aerodynamic pressure distributions, using a finite-element method for structural analysis, and using a fully stressed design technique to size structural members. This system is tailored to perform the entire process with computational efficiency in a single computer run so that it can be used effectively during preliminary design. Selected results, considering maneuver, taxi, and fatigue design conditions, are presented to illustrate convergence characteristics of this iterative procedure.

Giles, G. L.↗

Air cushion landing system

Static and dynamic performance of air cushion landing system is simulated in computer program that treats four primary ACLS subsystems: fan, feeding system, trunk, and cushion. Configuration of systems is sufficiently general to represent variety of practical designs.

Boghami, K. M.↗

SPAR data handling utilities

The SPAR computer software system is a collection of processors that perform particular steps in the finite-element structural analysis procedure. The data generated by each processor are stored on a data base complex residing on an auxiliary storage device, and these data are then used by subsequent processors. The SPAR data handling utilities use routines to transfer data between the processors and the data base complex. A detailed description of the data base complex organization is presented. A discussion of how these SPAR data handling utilities are used in an application program to perform desired user functions is given with the steps necessary to convert an existing program to a SPAR processor by incorporating these utilities. Finally, a sample SPAR processor is included to illustrate the use of the data handling utilities.

Giles, G. L.↗

Conceptual design and cost analysis of hydraulic output unit for 15 kW free-piston Stirling engine

A long-life hydraulic converter with unique features was conceptually designed to interface with a specified 15 kW(e) free-piston Stirling engine in a solar thermal dish application. Hydraulic fluid at 34.5 MPa (5000 psi) is produced to drive a conventional hydraulic motor and rotary alternator. Efficiency of the low-maintenance converter design was calculated at 93.5% for a counterbalanced version and 97.0% without the counterbalance feature. If the converter were coupled to a Stirling engine with design parameters more typcial of high-technology Stirling engines, counterbalanced converter efficiency could be increased to 99.6%. Dynamic computer simulation studies were conducted to evaluate performance and system sensitivities. Production costs of the complete Stirling hydraulic/electric power system were evaluated at $6506 which compared with $8746 for an alternative Stirling engine/linear alternator system.

White, M. A.↗

A common geometric data-base approach for computer-aided manufacturing of wind-tunnel models and theoretical aerodynamic analysis

A more automated process to produce wind tunnel models using existing facilities is discussed. A process was sought to more rapidly determine the aerodynamic characteristics of advanced aircraft configurations. Such aerodynamic characteristics are determined from theoretical analyses and wind tunnel tests of the configurations. Computers are used to perform the theoretical analyses, and a computer aided manufacturing system is used to fabricate the wind tunnel models. In the past a separate set of input data describing the aircraft geometry had to be generated for each process. This process establishes a common data base by enabling the computer aided manufacturing system to use, via a software interface, the geometric input data generated for the theoretical analysis. Thus, only one set of geometric data needs to be generated. Tests reveal that the process can reduce by several weeks the time needed to produce a wind tunnel model component. In addition, this process increases the similarity of the wind tunnel model to the mathematical model used by the theoretical aerodynamic analysis programs. Specifically, the wind tunnel model can be machined to within 0.008 in. of the original mathematical model. However, the software interface is highly complex and cumbersome to operate, making it unsuitable for routine use. The procurement of an independent computer aided design/computer aided manufacturing system with the capability to support both the theoretical analysis and the manufacturing tasks was recommended.

See, M. J.↗

Improvement of the Earth's gravity field from terrestrial and satellite data

The terrestrial gravity data base was updated. Studies related to the Geopotential Research Mission (GRM) have primarily considered the local recovery of gravity anomalies on the surface of the Earth based on satellite to satellite tracking or gradiometer data. A simulation study was used to estimate the accuracy of 1 degree-mean anomalies which could be recovered from the GRM data. Numerous procedures were developed for the intent of performing computations at the laser stations in the SL6 system to improve geoid undulation calculations.

Source record↗

Description of an oscillating flow pressure drop test rig

A test rig designed to generate heat exchanger pressure drop information under oscillating flow conditions is described. This oscillating flow rig is based on a variable stroke and variable frequency linear drive motor. A frequency capability of 120 hertz and a mean test pressure up to 15 mPA (2200 psi) allows for testing at flow conditions found in modern high specific power Stirling engines. An important design feature of this rig is that it utilizes a single close coupled dynamic pressure transducer to measure the pressure drop across the test sample. This eliminates instrumentation difficulties associated with the pressure sensing lines common to differential pressure transducers. Another feature of the rig is that it utilizes a single displacement piston. This allows for testing of different sample lengths and configurations without hardware modifications. All data acquisition and reduction for the rig is performed with a dedicated personal computer. Thus the overall system design efficiently integrates the testing and data reduction procedures. The design methodology and details of the test rig is described.

Wood, J. Gary↗

Telemetry handling on the Space Station data management system

This paper examines the impact of telemetry handling on the design of the onboard networks that are part of the Space Station Data Management System (DMS). An architectural approach to satisfying the DMS requirement for support of the high throughput needed for telemetry transport and for servicing distributed computer systems is discussed. Several of the functionality vs. performance tradeoffs that must be made in developing an optimized mechanism for handling telemetry data in the DMS are considered.

Whitelaw, Virginia A.↗

Trajectory analysis for low thrust maneuvers and drag decay in low earth orbit operations

In the 1990s low earth orbit operations are anticipated which will include the Space Station and orbital maneuver vehicle (OMV) serviceable satellites requiring reboost and coordination despite drag decay and oblateness effects. A low thrust targeting algorithm is described applicable to Space Station and the OMV. Tests were made with Space Station reboost requirements and an oblate gravity model. The reboost requirements were determined based on projected station growth, atmospheric models and anticipated flight profiles. The targeting algorithm as well as the algorithm for predicting orbital decay are perturbation formulations of more 'transcendental' systems and are used in interactive personal computer simulations. Performance results and a discussion for the Space Station problems are provided.

Kelly, W. D.↗

Description of an oscillating flow pressure drop test rig

A test rig designed to generate heat exchanger pressure drop information under oscillating flow conditions is described. This oscillating flow rig is based on a variable stroke and variable frequency linear drive motor. A frequency capability of 120 hertz and a mean test pressure up to 15 mPA (2200 psi) allows for testing at flow conditions found in modern high specific power Stirling engines. An important design feature of this rig is that it utilizes a single close coupled dynamic pressure transducer to measure the pressure drop across the test sample. This eliminates instrumentation difficulties associated with the pressure sensing lines common to differential pressure transducers. Another feature of the rig is that it utilizes a single displacement piston. This allows for testing of different sample lengths and configurations without hardware modifications. All data acquisition and reduction for the rig is performed with a dedicated personal computer. Thus the overall system design efficiently integrates the testing and data reduction procedures. The design methodology and details of the test rig are described.

Wood, J. Gary↗