SEARCH · Engineering Papers

Results for “carbon removal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS2018

Co-Adsorption of Carbon Dioxide on Zeolite 13X in the Presence of Preloaded Water

Environmental Control and Life Support requires highly effective CO2 removal systems. The current system onboard the International Space Station is known as Carbon Dioxide Removal Assembly. Recent high-fidelity simulation of this system predicted a major efficiency gain via reduction of desiccant zeolite. Commercial beaded 13X zeolite is used in the desiccant bed to scrub water below 1 ppm but is also a highly active CO2 sorbent. The simultaneous adsorption of water vapor and CO2 is known to strongly favor water, but more accurate measurements are needed. This work details the characterization of the zeolite to be used in the next-generation CO2 removal system for co-adsorption of water and CO2.

Cmarik, Gregory E↗

NASA NTRS2008

Testing, Modeling and System Impact of Metabolic Heat Regenerated Temperature Swing Adsorption

Metabolic heat regenerated temperature swing adsorption (MTSA) technology is being developed for removal and rejection of carbon dioxide (CO2) and heat from a portable life support system (PLSS) to the Martian environment. Previously, hardware was built and tested to demonstrate using heat from simulated, dry ventilation loop gas to affect the temperature swing required to regenerate an adsorbent used for CO2 removal. New testing has been performed using a moist, simulated ventilation loop gas to demonstrate the effects of water condensing and freezing in the heat exchanger during adsorbent regeneration. In addition, thermal models of the adsorbent during regeneration were modified and calibrated with test data to capture the effect of the CO2 heat of desorption. Finally, MTSA impact on PLSS design was evaluated by performing thermal balances assuming a specific PLSS architecture. Results using NASA s Extravehicular Activity System Sizing Analysis Tool (EVAS_SAT), a PLSS system evaluation tool, are presented.

Lacomini, Christine S.↗

DOE OSTI2022

Regenerable solvents mediate accelerated low temperature CO 2 capture and carbon mineralization of ash and nano-scale calcium carbonate formation

The dual need to remove CO 2 from our emissions and treat alkaline industrial residues such as ash materials motivate the design of innovative pathways to simultaneously capture and convert CO 2 into mineralized carbonates. Direct carbon mineralization is one approach that addresses the need to simultaneously treat alkaline industrial residues and mineralize CO 2 emissions. Low CO 2 solubility in water and slow kinetics at ambient temperature have challenged the direct carbon mineralization of alkaline industrial residues. Here, to address these challenges, the use of CO 2 capture solvents that enhance CO 2 solubility and facilitate accelerated carbon mineralization of fly ash at temperatures below 90 °C is investigated. Calcium carbonate formation results in the inherent regeneration of the solvent. The carbon mineralization extents of non-calcium carbonate content in fly ash were 50% and 51% and in waste ash were 58% and 62% in 2.5 M sodium glycinate and 30 wt% MEA solutions, respectively. The experiments were performed at 50 °C for 3 hours with CO 2 partial pressure of 1 atm in a continuously stirred slurry environment with 15 wt.% solid. Furthermore, nanoscale CaCO 3 is successfully synthesized from dissolved calcium using CO 2 -loaded sodium glycinate and surfactants such as CTAB (Cetyl Trimethyl Ammonium Bromide). Surfactants such as CTAB bind to the calcium carbonate surface and regulate the growth of calcium carbonate particles. These innovative approaches demonstrate the feasibility of directly storing CO 2 in fly ash and waste ash as calcium carbonate and producing nanoscale calcium carbonate using regenerable CO 2 capture solvents.

42 ENGINEERING↗

NASA NTRS2014

Amine Swingbed Payload Technology Demonstration

The Amine Swingbed Payload is a technology demonstration of an amine-based carbon dioxide (CO2) and water vapor (H2O) removal system in the U.S. Lab onboard the International Space Station (ISS). The technology utilizes the Carbon dioxide And Moisture Removal Amine Swingbed, or CAMRAS, which is the baseline technology for controlling CO2 and water vapor in the habitable spacecraft for Orion's Multi-Purpose Crew Vehicle (MPCV). For testing on the ISS, the payload also employs water-saving and air-saving subsystems to reduce resources normally vented to space vacuum. This presentation will describe the physical design of the payload, the operation and performance results of the payload during its on-orbit tests between May 2013 and February 2014, and future plans for the payload. Troubleshooting efforts and the resolution of specific anomalies encountered during the initial operation of the payload are also discussed.

Sweterlitsch, Jeffrey↗

DOE OSTI2020

Removal of Metal Oxides from Reactor Metals/Alloys by Laser Ablation

Storage of low and intermediate level radioactive waste in a deep geological repository (L and ILW DGR): - Large volumes of metallic waste = increased production of hydrogen gas. - Large fraction of the metallic wastes are out-of-core reactor components. - Carbon steel feeder pipes. - Radioactive contamination is concentrated within the surface oxides. - Removal of surface contaminants would lead to volume reduction of metallic waste that is stored in L and ILW DGR. - Current decontamination techniques generate large volumes of secondary waste. Objectives: Oxide removal from carbon steel using a ytterbium fiber laser (1064 nm) with a particular focus on identifying the key laser parameters that affect the removal efficiency. Advantages of laser ablation: Generate low volumes of waste, Flexibility of deployment, Remote operation. Grow an oxide film on carbon steel with the incorporation of cobalt. Optimize laser cleaning technology for the removal of surface oxides. Incorporate an oxide collection system for the ablated particles. Conclusions: Objective 1 - Simulated inactive oxides on carbon steel, using Co{sup 2+} as a surrogate for Co radionuclide. Objective 2 - Optimized laser parameters (200 MW/cm{sup 2}, 3 scans, 15 μm overlap); Complete removal of cobalt from surface and bulk metal with optimized cleaning settings. Objective 3 - Glass fiber media H14 HEPA filters had highest collection yield; High oxide collection yields (∼100%). Future Work: Further testing of the liquid trap will verify the efficacy of the HEPA filter and determine the amount of ablated oxides that pass through. Testing of the laser ablation system needs to be done on other reactor materials along with the incorporation of different transition metal cations. Improvements to the oxide collection system are required to improve collection yields.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

Recycling of PET by Dissolution-Purification-Recovery (DPR) Process Using Bioderived Solvent

Polyethylene terephthalate (PET) waste continues to accumulate at staggering rates, with the majority still routed to landfills due to limitations in current recycling methods. While mechanical recycling is widely implemented, it struggles to effectively remove colorants, additives, and harmful contaminants - resulting in discolored, degraded materials with limited reuse potential. In this presentation, we demonstrate a scalable dissolution-purification-recovery (DPR) process designed to selectively reclaim high-purity PET from post-consumer bottle flake. The method utilizes a food grade bio-based solvent for targeted PET dissolution, followed by activated carbon treatment for impurity removal and antisolvent-induced precipitation for polymer recovery. The resulting recycled PET exhibits complete decolorization, significantly reduced metal contamination, and minimal loss in molecular weight. These performance metrics indicate strong suitability for remanufacturing into new bottles, offering a circular alternative to traditional mechanical recycling pathways.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

An Improved Representation of Aerosol Wet Removal by Deep Convection and Impacts on Simulated Aerosol Vertical Profiles

Here, we introduce a physics-based aerosol wet removal scheme with unified treatments of aerosol transport and removal by convective clouds into the Community Atmosphere Model version 6. Since several important physical processes are still neglected or poorly represented in this new physics-based scheme, we develop secondary improvements to the parameterizations of aerosol activation, resuspension, and cloud-borne aerosol detrainment in this new scheme. Changes in the aerosol wet removal scheme cause tropospheric aerosol concentrations to decrease to different extents: compared to the control run, the physics-based scheme significantly decreases aerosol burdens by up to 60% over the southern Pacific Ocean, whereas the secondary improvements mitigate the decreasing tendency. The burden changes also depend on aerosol chemical components: the sulfate mass decrease is compensated by secondary production, black carbon (BC) is effectively removed via increasing the hygroscopicity of particulate organic matter from 0 to 0.2, and dust shows the most spatially heterogeneous changes. Simulated aerosol profiles are evaluated against aircraft-based observations over the Pacific and Atlantic Oceans. The secondary-improved scheme reduces the overestimations of upper tropospheric BC and sea salt concentrations by a factor of 10 and 1,000, respectively, and reproduces the dependence of BC mass decrease rates on cloud types. Consideration of convective cloud-borne aerosol detrainment plays the most important role in enhancing the aerosol wet removal and decreasing the positive biases of tropospheric BC and sea salt concentrations. We also summarize unresolved issues related to convective cloud genesis and microphysics, cloud-borne aerosol evolution, and BC and dust emissions.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1992

Use of sorption technology for treatment of humidity condensate for potable water

This research focused on the testing of the original potable water processor aboard Space Station Freedom that was to produce potable water from the humidity condensate and additional water generated by carbon dioxide reduction. Humidity condensate was simulated by an influent water model 'Ersatz'. The humidity condensate was treated with multifiltration (MF) beds that consisted of a train of sorption beds (referred to as 'Unibed') designed to remove specific contaminants. For the complete simulated MF system runs tested for 100 bed volumes (BV) (volume processed/total column volume), 0.6 percent of the TOC was removed by the SAC/IRN 77 (Strong Acid Cation exchange resin), 39.6 percent of the total organic carbon (TOC) was removed by the WBA/IRA 68 (Weak Base Anion exchange resin), 13.2 percent of the TOC was removed by activated carbon adsorption (580-26), and the remaining sorbent media acted as polishing units to remove an additional 1.6 percent of the TOC at steady state. At steady state, 45 percent of the influent TOC passed through the MF bed.

Ajjarapu, Sundara R. M.↗

NASA NTRS1990

The sensitivity of terrestrial carbon storage to climate change

The role of the terrestrial biosphere in controlling atmospheric CO2 levels during climate perturbations is estimated. Simulations are used to calculate the local geographical distribution of vegetation during the last glacial maximum. The known changes in sea level at this time, together with the simulated climate-driven spatial arrangement of vegetation, result in a mass transfer of carbon from the terrestrial biosphere to the atmosphere ranging from 30 Gt (corresponding to 15 ppm CO2) to -50 Gt (25 ppm). Thus, although the biosphere may have contributed to the decrease in atmospheric CO2 at 80 ppm, known to have occurred at 18 kyr, it does not seem to have been a dominant factor. For simulations run with twice the present-day CO2 levels, strong negative feedbacks appear which remove 235 Gt of carbon from the atmosphere.

Prentice, Katharine C.↗

DOE OSTI2021

Assessing the physical potential capacity of direct air capture with integrated supply of low-carbon energy sources

Direct Air Capture (DAC) is a negative emission technology that can remove up to 10–20 Gt of CO 2 per year. However, to achieve this potential, DAC systems must be coupled to suitable locally available energy sources and sited near geological storage. Here this study explores the potential of low-carbon energy sources to supply power and heat to the DAC process in a dedicated, self-sufficient system tailored for each energy source. Solar, geothermal, woody biomass, wind, and nuclear energy sources are assessed for their global energy supply potential and possible land use requirements. While the options differ in area requirement and regional efficacy, we estimate that all the regionally specific technologies considered can supply energy to achieve significant removal of carbon dioxide from the atmosphere globally. The amount of energy physically available from solar, offshore wind, and woody biomass converts to a removal potential of 160–971, 45–150, and 2–5 Gt CO 2 /year, respectively. Thus, negative emission targets can be reached by utilizing a moderate fraction of the overall potential of several different low-carbon energy sources for DAC while the magnitude of the potential changes significantly according to the source of energy.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS2002

Tensile Behavior of As-Fabricated and Burner-Rig Exposed SiC/SiC Composites with Hi-Nicalon Type-S Fibers

Tensile stress-strain curves were measured at room temperature and 1315 C for 2D-woven SiC/BN/SiC ceramic matrix composites (CMC) reinforced by two variations of Hi-Nicalon Type-S SiC fibers. These fibers, which contained a thin continuous carbon-rich layer on their as-produced surface, provided the as-fabricated CMC with good composite behavior and an ultimate strength and strain of -350 MPa and -0.5%, respectively. However, after un-stressed burner-rig exposure at 815 C for -100 hrs, CMC tensile specimens with cut edges and exposed interphases showed a significant decrease in ultimate properties with effectively no composite behavior. Microstructural observations show that the degradation was caused by internal fiber-fiber oxide bonding after removal of the carbon-rich fiber surface layer by the high-velocity combustion gases. On the other hand, SiC/BN/SiC CMC with Sylramic-iBN fibers without carbon-rich surfaces showed higher as-fabricated strength and no loss in strength after the same burner rig exposure. Based on the strong role of the carbon layer in these observations, a process method was developed and demonstrated for achieving better strength retention of Hi-Nicalon Type-S CMC during burner rig exposure. Other general approaches for minimizing this current deficiency with as-produced Type-S fibers are discussed.

Yun, H. M.↗

DOE OSTI2022

Coupling gas purging with inorganic carbon supply to enhance biohydrogen production with Clostridium thermocellum

Clostridium thermocellum is a desirable biocatalyst for biohydrogen production, with a native ability to simultaneously saccharify cellulose and to metabolize released cellodextrins for hydrogen production. During fermentation with C. thermocellum , partial pressures of two gases - CO 2 and H 2 - are critical drivers of overall reaction kinetics. Biohydrogen production is enhanced by maintaining a low hydrogen partial pressure, while high concentrations of dissolved CO 2 promote microbial biomass synthesis. Our study evaluates the inherent trade-offs between hydrogen stripping and inorganic carbon supply for optimized biohydrogen synthesis. Here, we find that nitrogen sparging at low flow rates increases hydrogen production when compared with an equivalent nitrogen overlay, but that high rates of nitrogen sparging inhibit cell growth and hydrogen production. Decreasing dissolved hydrogen partial pressure via nitrogen sparging also lowers the production of reduced metabolites, including lactate and ethanol. To address potential stripping of inorganic carbon from the production medium, we supplemented CO 2 to the sparging gas and co-optimized for gas flow rate and for the CO 2 fraction of the sparging gas. Total hydrogen production increased from 50 mmol∙L -1 in the base condition, when the bioreactor was sparged with 0.1 LPM of pure nitrogen, to 181.3 mmol∙L -1 when sparged with 1.3 LPM of 33 % CO 2 , demonstrating that biohydrogen production is highly sensitive to both parameters. Fine sensitivity of biohydrogen production to sparging conditions highlights the critical importance of bioreactor design and operation to achieve maximum H 2 removal without compromising inorganic carbon supply to bacterial central metabolism.

09 BIOMASS FUELS↗

NASA NTRS1994

Adsorption and Desorption of Carbon Dioxide and Water Mixtures on Synthetic Hydrophobic Carbonaceous Adsorbents

Several synthetic carbonaceous adsorbents produced through pyrolysis of polymeric materials are available commercially. Some appear to have advantages over activated carbon for certain adsorption applications. In particular, they can have tailored hydrophobicities that are significantly greater than that of activated carbon, while moderately high surfaces areas are retained. These sorbents are being investigated for possible use in removing trace contaminants and excess carbon dioxide from air in closed habitats, plant growth chambers, and other applications involving purification of humid gas streams. We have analyzed the characteristics of a few of these adsorbents through adsorption and desorption experiments and standard characterization techniques. This paper presents pure and multicomponent adsorption data collected for carbon dioxide and water on two synthetic carbonaceous adsorbents having different hydrophobicities and capillary condensation characteristics. The observations are interpreted through consideration of the pore structure and surface chemistry of the solids and interactions between adsorbed carbon dioxide, water, and the solvent gas.

Finn, John E.↗

NASA NTRS2009

Design and Testing of Trace Contaminant Injection and Monitoring Systems

In support of the Carbon dioxide And Moisture Removal Amine Swing-bed (CAMRAS) testing, a contaminant injection system as well as a contaminant monitoring system has been developed by the Johnson Space Center Air Revitalization Systems (JSC-ARS) team. The contaminant injection system has been designed to provide trace level concentrations of contaminants generated by humans in a closed environment during space flight missions. The contaminant injection system continuously injects contaminants from three gas cylinders, two liquid reservoirs and three permeation ovens. The contaminant monitoring system has been designed to provide real time gas analysis with accurate flow, humidity and gas concentration measurements for collection during test. The contaminant monitoring system consists of an analytical real time gas analyzer, a carbon monoxide sensor, and an analyzer for ammonia and water vapor.

Broerman, Craig D.↗

NASA NTRS2017

Sorbent-Based Atmosphere Revitalization System

The present invention is a sorbent-based atmosphere revitalization (SBAR) system using treatment beds each having a bed housing, primary and secondary moisture adsorbent layers, and a primary carbon dioxide adsorbent layer. Each bed includes a redirecting plenum between moisture adsorbent layers, inlet and outlet ports connected to inlet and outlet valves, respectively, and bypass ports connected to the redirecting plenums. The SBAR system also includes at least one bypass valve connected to the bypass ports. An inlet channel connects inlet valves to an atmosphere source. An outlet channel connects the bypass valve and outlet valves to the atmosphere source. A vacuum channel connects inlet valves, the bypass valve and outlet valves to a vacuum source. In use, one bed treats air from the atmosphere source while another bed undergoes regeneration. During regeneration, the inlet, bypass, and outlet valves sequentially open to the vacuum source, removing accumulated moisture and carbon dioxide.

Knox, James C↗

DOE OSTI2021

Grafted nickel-promoter catalysts for dry reforming of methane identified through high-throughput experimentation

High-throughput synthesis of a series of monometallic and bimetallic catalysts (45 bimetallic and 50 monometallic samples) consisting of nickel and one of nine different metal promoters (B, Co, Cu, Fe, Mg, Mn, Sn, V and Zn) supported on one of six different metal oxides alumina, ceria, magnesia, silica and titania) is carried out via organometallic grafting using a robotic platform. The catalysts are evaluated for their activity and selectivity for the dry reforming of methane at a feed ratio of CH 4 :CO 2 of 1 at 650–800 °C in a parallel flow reactor system. The type of oxide support prevails over the type of additive for both catalyst activity and stability. On Al 2 O 3 and MgO, Fe was found to be the best promoter; on SiO 2 , Cu is the best promoter at 700 °C and higher, while on TiO 2 , Mn is found to enhance the conversion at 800 °C. On CeO 2 , all additives except Fe have beneficial effects. Twenty-five catalysts show > 90% methane conversion with ten catalysts showing > 95% conversion at 800 °C with the H 2 :CO ratios ranging from 0.8 to 1.2. Amongst the ten highest performers, NiFe/Al 2 O 3 and NiFe/MgO are more active than Ni/Al 2 O 3 and Ni/MgO, respectively and were stable over a period of 25 h at 800 °C. Characterization on the as-prepared samples reveals highly dispersed phase, while after reduction in H 2 , highly dispersed and reduced nickel particles up to 10 nm are formed. The particles do not increase in size under dry reforming reaction conditions at 800 °C. An increased hydrogen consumption observed during H 2 -TPR of the nickel particles is positively correlated with methane conversion for Al 2 O 3 -based catalysts. The resistance to deactivation by coking and variation in coke structure are investigated by spectroscopic and microscopic methods to identify the relationship between metal promoters, alloy formation, and type of surface carbon deposits. Carbon whiskers were observed on the ten selected spent samples and are preferentially deposited on Ni rather than on the promoters. Carbon nanotube formation and metal particle removal from support were not observed to cause deactivation while amorphous carbon formation was clearly linked to catalyst deactivation, as amorphous carbon could encapsulate nickel, either on the support or at the end of the carbon nanotube. Furthermore, the organometallic grafting technique is an efficient and suitable technique for synthesizing highly dispersed and homogeneous phases which lead to high conversion and high durability for dry reforming of methane.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Data for 3-Hydroxypropionic Acid Recovery from Fermentation Broth through Novel Downstream Processing: Technoeconomic Analysis

This study develops and validates a simplified, fully solvent-free downstream processing (DSP) strategy for high-purity recovery of 3-hydroxypropionic acid (3-HP) from real fermentation broth containing 62.3 g/L of 3-HP. Optimized activated carbon treatment achieved 98% color removal, while Amberlite IRA-67 was operated at pH 4.5 and 30 °C to minimize product loss. This is the first integrated demonstration of a fully solvent-free DSP enabling recovery of bio-based 3-HP as both a solid sodium salt and a concentrated aqueous solution, supported by techno-economic analysis. At lab scale, the process achieved 77.3% recovery of sodium 3-HP with 83.2% (w/w) purity and produced a 30% (w/v) aqueous solution. Techno-economic analysis yielded minimum selling prices of $0.551/kg for the solution and $0.892/kg for the salt, both below target thresholds for cost-competitive bio-acrylic acid production. Overall, these results demonstrate an efficient, scalable, and economically viable industrial pathway for 3-HP recovery.

Bioproducts↗

DOE OSTI2020

Modeling Functional Organic Chemistry in Arctic Rivers: An Idealized Siberian System

Rivers of the Arctic will become ever more important for the global climate, since they carry a majority of continental dissolved organic carbon flux into the rapidly changing polar ocean. Aqueous organics comprise a wide array of functional groups, several of which are likely to impact coastal and open water biophysical properties. Light attenuation, interfacial films, aerosol formation, gas release and momentum exchange can all be cited. We performed Lagrangian kinetic modeling for the evolution of riverine organic chemistry as the molecules in question make their way from the highlands to Arctic outlets. Classes as diverse as the proteins, sugars, lipids, re-condensates, humics, bio-tracers and small volatiles are all included. Our reduced framework constitutes an idealized northward flow driving a major hydrological discharge rate and primarily representing the Russian Lena. Mountainous, high solute and tundra sources are all simulated, and they meet up at several points between soil and delta process reactors. Turnover rates are parameterized beginning with extrapolated coastal values imposed along a limited tributary network, with connections between different terrestrial sub-ecologies. Temporal variation of our total dissolved matter most closely resembles the observations when we focus on the restricted removal and low initial carbon loads, suggesting relatively slow transformation along the water course. Thus, channel combinations and mixing must play a dominant role. Nevertheless, microbial and photochemical losses help determine the final concentrations for most species. Chemical evolution is distinct for the various functionalities, with special contributions from pre- and post-reactivity in soil and delta waters. Several functions are combined linearly to represent the collective chromophoric dissolved matter, characterized here by its absorption. Tributaries carry the signature of lignin phenols to segregate tundra versus taiga sources, and special attention is paid to the early then marine behaviors of low molecular weight volatiles. Heteropolycondensates comprise the largest percentage of reactive carbon in our simulations due to recombination/accumulation, and they tend to be preeminent at the mouth. Outlet concentrations of individual structures such as amino acids and absorbers lie above threshold values for biophysical influence, on the monolayer and light attenuation. The extent of coastal spreading is examined through targeted regional box modeling, relying on salinity and color for calibration. In some cases, plumes reach the scale of peripheral arctic seas, and amplification is expected during upcoming decades. Conclusions are mapped from the Lena to other boreal discharges, and future research questions are outlined regarding the bonding type versus mass release as permafrost degrades. Dynamic aqueous organic coupling is recommended for polar system models, from headwaters to coastal diluent.

54 ENVIRONMENTAL SCIENCES↗