Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “blade”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Conceptual Designs of the Structure of Inflatable Blades for Enabling Larger Turbines

Over the last couple of decades, increasingly larger rotor diameters have enabled significant reductions in the levelized cost of energy for wind through higher energy capture and improved capacity factors. But for onshore turbines, this has been met with manufacturing and transportation challenges. To enable larger onshore rotors, an innovative inflatable blade concept is investigated that employs both traditional and onsite manufacturing. The design architecture consists primarily of an inflatable aerodynamic shell attached to a factory-manufactured primary structure. Multiple architectures, cross-sectional topologies, and material combinations for the primary structure are investigated, as well as multiple skin materials. Structural cross-sectional characteristics are compared to a traditional blade, and inflatability and cost evaluations are presented. Results show that a box-beam architecture using only composite materials yields significant mass reduction with mature technologies/processes and modest cost decrease compared to traditional blade construction. This low-TRL study demonstrates the inflatable blade concept's techno-economic potential.

49 EE - Wind and Water Power Program - Wind (EE-4W↗
DOE OSTI2022

Blade Coating Inverted Perovskite Solar Cells with Vacuum-Assisted Nucleation Based on Bottom Quasi-2D Passivation

Metal halide perovskite solar cells (PSCs) attract an enormous attention because of their high power conversion efficiency (PCE) and low fabrication cost. However, their commercialization is limited by fabricating highly efficient large-area solar cells. Controlling the morphology and crystallization of perovskite for large-area fabrication is difficult but important. Here, in this work, a vacuum-assisted approach is developed to obtain mirror-like, pinhole-free, highly crystalline, and uniform blade-coated perovskite films, without the use of antisolvent and air knife. This method can be a universal approach for various perovskite compositions. Meanwhile, the phenethylammonium iodide passivation effect at the top and bottom interfaces of perovskite layer based on FTO/NiO x /perovskite/C 60 /BCP/Cu inverted p-i-n structure is systematically investigated. The optimized device fabricated by blade coating under an ambient environment exhibits the champion PCE of 20.7% and is among the top few records of blade coating inverted structure based on NiOx hole transport layer. The encapsulated device retains 97% of its maximum efficiency under open-circuit condition after 1000 h of photostability test in an ambient environment at room temperature with a relative humidity of 40–60%. Herein, low-cost, easy, and reproducible strategies to fabricate efficient and stable blade-coated PSCs are demonstrated.

14 SOLAR ENERGY↗
DOE OSTI2022

Blade planform design optimization to enhance turbine wake control

Abstract This study considers optimizing the planform of wind turbine blades to ultimately enhance wind plant controls, namely, wake steering strategies. Adjoint‐enabled unsteady actuator line simulations are carried out to obtain gradients for optimization of several different performance objectives with respect to blade chord length at 10 locations along blade span. We demonstrate different blade design optimizations that can maximize time‐averaged lateral wake deflection, entrainment of kinetic energy, or total power of multiple turbines. Our optimized designs can produce a 4+% increase in wake deflection, a 4× increase in vertical kinetic energy entrainment, or a 3.6% increase in power when compared with the baseline case. While lateral wake deflection is only modestly sensitive to chord changes, we find that increasing the outboard chord length can dramatically increase kinetic energy entrainment, resulting in faster wake recovery and gains in net power. While this work develops only a few case studies emphasizing relative performance improvements and general trends, these results show the promise of a framework that combines mid‐fidelity computation with adjoint‐based optimization for control and design problems.

WIND ENERGY↗
DOE OSTI2022

Regional Representation of Wind Stakeholders' End-of-Life Behaviors and Their Impact on Wind Blade Circularity

Wind plant power has seen tremendous growth in the US and worldwide, representing the most significant renewable energy installed capacity besides hydropower. While wind power enables decarbonizing the electricity grid, the rising amount of end-of-life (EOL) wind blades - which are arduous to recycle - present a challenge for landfills if disposed of whole and a missed opportunity to recover valuable composite materials. The circular economy (CE) concept proposes strategies to rethink, reuse and recover products, components, and materials. However, transitioning to a CE implies changing how business models, supply chains, and behaviors deal with products and waste; changes arduously captured with traditional methods used to assess circularity such as life cycle assessment or material flow analysis (MFA). Here we present an agent-based model (ABM) that captures behavioral aspects impacting wind blade circularity in the US. The ABM also accounts for wind plant projects and landfills heterogeneity - a characteristic not easily included in top-down approaches such as MFA, input-output analysis, or system dynamics. Results show that recycling is divided as most recycling facilities are on the eastern side of the country, a challenge that could be alleviated by shredding blades before transportation. Recycling programs from the wind industry could also seed recycling behaviors within wind plant owners. Better yet, new blade designs could increase circularity if original equipment manufacturers accept the risks involved with the investments needed to adapt the production lines.

17 WIND ENERGY↗
DOE OSTI2026

Numerical simulation of vortex-induced vibration response of a single IEA 10-MW wind turbine blade

Three-dimensional simulation of vortex-induced vibration (VIV) of a single International Energy Agency (IEA) 10-MW reference wind turbine blade with a length of 97.325 m is performed using the ExaWind stack, an open-source suite of codes. This study aims to illustrate the spanwise VIV response characteristics and cross-validate the results with an existing commercial framework. Five near-body meshes and three time steps are selected for the convergence study. To improve computational efficiency, several VIV triggering methods are also compared to shorten the VIV development period. The ExaWind-based VIV simulation strategy for a single IEA 10-MW blade is determined. First, the modal shape is validated against published results. Then, spanwise VIV responses of four blade configurations under a fixed and varied incoming flow velocity are analyzed. Results show that the VIV response is dominated by the first edgewise (second overall) mode. Little first-mode contributions appear near the second-mode node, producing a pi phase jump, and a higher harmonics response occurs near the blade root. Rotational degrees of freedom are minor compared with translational motion. The response versus reduced velocity is analyzed, showing a two-branch behavior similar to that of VIV for a bluff cylinder. Across all tested cases, the dominant frequency remains locked to the natural frequency of the second mode with no observed desynchronization. A mild deviation is observed for the case of 90-degree pitch and 310-degree azimuth rotation near a reduced velocity of 6, which will be examined with additional cases in future work. These findings indicate that severe VIV responses can arise under specific configurations and flow conditions, thereby increasing the potential for VIV fatigue damage and requiring greater attention during operation.

17 WIND ENERGY↗
DOE OSTI2021

Autonomous Sensor System for Wind Turbine Blade Collision Detection

This paper presents an automated blade collision detection system for use on wind turbines, toward the goal of supporting monitoring and quantitative assessment of wind energy impacts on wildlife. A wireless, multisensor module mounted at the blade root measures surface vibrations, and a blade-mounted camera provides image capture of colliding objects. Using sensor data recorded during field testing of the system on an operational wind turbine, we present the development, training, and testing of automated detection algorithms for collision detection using machine-learning approaches. In particular, we compare the use of a new two-step, anomaly-based classification algorithm with conventional adaptive boosting and amplitude-based detection techniques, where the two-step approach improves average precision for the experimental data set. This integrated sensor and classification systems demonstrates a new approach for automated, on-blade collision detection for wind turbines, with broad utility across structural health monitoring applications.

17 WIND ENERGY↗
DOE OSTI2024

Blade Designs For Improved Multi-Phase Performance In sCO 2 Compressors; Part II - Optical Diagnostics In sCO 2 And Experimental Evaluation With Particle Image Velocimetry

This paper presents the second part of a study in which the leading-edge and suction surface of a compressor blade was modified to delay onset of phase change for sCO 2 compressors operating near the critical point. Using a first-of-its-kind apparatus for the measurement of sCO 2 flow fields, Particle Image Velocimetry (PIV) is used for local flow field measurements of two compressor blade geometries: the modified “biased-wedge,” and a conventional constant thickness blade. Utilizing the developed hardware, the feasibility of a simple, laser-based diagnostic for qualitatively measuring liquid phase regions, is also presented. The design of the optical diagnostics rig, a discussion of numerous challenges, and necessary considerations involved in performing optical-based measurements like PIV, in sCO 2 , are discussed. Velocity field measurements for the modified compressor profile show a much lower suction peak compared to a conventional blade. Furthermore, these results validate numerical results at the tested conditions, where the suction side profile of the biased wedge works to minimize the local pressure gradient.

14 SOLAR ENERGY↗
DOE OSTI2022

Characterization and repair of core gap manufacturing defects for wind turbine blades

Various wind turbine blade components, such as shear webs and skins, commonly use fiber-reinforced composite sandwich structures with a core material like balsa or foam. During manufacturing, core gap defects may result from the misalignment of adjacent foam or balsa core sheets in the blade mold. It is important to understand the influence that core gaps have on the structural integrity of wind turbine blades and how to mitigate their influence. This research characterized the effects of core gap defects at the manufacturing and mechanical levels for both epoxy and next-generation thermoplastic composites. Common repair methods were assessed and compared. Multiple defect sizes were compared using temperature data gathered with thermocouples embedded during manufacturing to core gap defect characteristics obtained using image-mapping techniques, optical microscopy, and mechanical characterization by long beam flexure. Results showed that peak exothermic temperatures during curing were closely related to core gap size. The long beam flexure tests determined that transverse core gaps under pure bending loads can have a substantial effect on the ultimate facesheet strength of both epoxy and thermoplastic composite sandwich structures (up to 25% strength reduction), although the size of the defect itself had less of an influence on the magnitude of the strength reduction. The supporting image-mapping techniques indicated that the distortion of the composite facesheets by the core gaps contributed to the premature failures. The repair methods used in this study did very little to improve the ultimate strength of the sandwich panels that previously had core gap defects. The repair of the thermoplastic panel resulted in a further loss in ultimate facesheet strength. This research demonstrated that there is a vital need for the development of a compatible thermoplastic polymer repair resin system and appropriate resin specific repair procedures for the next generation of recyclable thermoplastic wind blades.

17 WIND ENERGY↗
DOE OSTI2023

Toward the Advanced Manufacturing of Land-Based Wind Turbine Blades

The National Renewable Energy Laboratory and General Electric (GE) are partners within the Additive and Modular-Enabled Rotor Blades and Integrated Composites Assembly (AMERICA) project. AMERICA aims to develop advanced manufacturing solutions to reduce labor and cycle time while increasing recyclability of wind turbine blades. The project is funded by the U.S. Department of Energy's Advanced Manufacturing Office. This paper describes the techno-economic and life cycle analysis of the novel manufacturing process applied to the 15-meter long tip of the blade of a representative 3.4 MW land-based wind turbine. We establish a comparison to a standard manufacturing process, highlighting challenges and opportunities. Several uncertainties affect the analysis, but we highlight an opportunity space. With the current set of assumptions, the tip adopting advanced manufacturing is predicted to lower labor by 21%, cycle time by 39%, and total blade tip costs by 15% while simultaneously increasing production quality and adopting recyclable thermoplastic resin. A life cycle analysis returns comparable metrics for climate change impact and embodied energy between the two processes.

3D printing↗
NASA NTRS1999

Aeroelastic Stability for Straight and Swept-Tip Rotor Blades in Hover and Forward Flight

Two isolated, hingeless rotors with identical fiber-reinforced composite root flexures were tested in hover and forward flight at realistic tip speeds. The rotors differed in blade planform and structure. The first blade set was of rectangular planform. The second set had blades of stiffer construction with swept-tips. The purpose of these tests was to measure the isolated rotor aeroelastic stability of bending/torsion coupled rotor blades over a range of flight conditions. The two soft inplane rotor systems were designed with low first torsion frequency to emphasize the effects of torsion. Regressing lag mode damping is shown in hover with precone and collective pitch variations and in forward flight with airspeed, shaft angle, precone and collective pitch variations. Correlation with comprehensive analysis for a number of test conditions is shown. Agreement in hover is excellent and forward flight correlation is reasonably good.

REGRESSING LAG MODE DAMPING↗
NASA NTRS2014

Blade Motion Correlation for the Full-Scale UH-60A Airloads Rotor

Testing was successfully completed in May 2010 on a full-scale UH-60A rotor system in the USAF's National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel.[1] The primary objective of this NASA Army sponsored test program was to acquire a comprehensive set of validation-quality measurements ona full-scale pressure-instrumented rotor system at conditions that challenge the most sophisticated modeling andsimulation tools. The test hardware included the same rotor blades used during the UH-60A Airloads flight test.[2] Key measurements included rotor performance, blade loads, blade pressures, blade displacements, and rotorwake measurements using large-field Particle Image Velocimetry (PIV) and Retro-reflective Background Oriented Schlieren (RBOS).

Airloads Rotor↗
NASA NTRS2016

An Assessment of the Icing Blade and the SEA Multi-Element Sensor for Liquid Water Content Calibration of the NASA GRC Icing Research Tunnel

The Icing Research Tunnel at NASA Glenn has recently switched from using the Icing Blade to using the SEA Multi-Element Sensor (also known as the multi-wire) for its calibration of cloud liquid water content. In order to peform this transition, tests were completed to compare the Multi-Element Sensor to the Icing Blade, particularly with respect to liquid water content, airspeed, and drop size. The two instruments were found to compare well for the majority of Appendix C conditions. However, it was discovered that the Icing Blade under-measures when the conditions approach the Ludlam Limit. This paper also describes data processing procedures for the Multi-Element Sensor in the IRT, including collision efficiency corrections, mounting underneath a splitter plate, and correcting for a jump in the compensation wire power. Further data is presented to describe the repeatability of the IRT with the Multi-Element Sensor, health-monitoring checks for the instrument, and a sensing-element configuration comparison. Ultimately these tests showed that in the IRT, the multi-wire is a better instrument for measuring cloud liquid water content than the blade.

aircraft icing↗
NASA NTRS2021

Evaluations of Damaged High-Pressure Compressor Blades in Two Turbine Engines of NASA DC–8

A series of flights were performed by the NASA DC-8 for the FIREX-AQ missions to observe the effects of wildfires and agricultural fires on air quality and climate in selected locations of the United States. Borescope evaluations after these flights indicated accelerated damage had occurred over this flight series to the blades in the high pressure compressor section of all four CFM56-2C1 turbine engines. This erosion and impact damage appeared to vary in severity, and appeared most severe for engines 3 and 4 located on the right wing of the DC-8.Engine 3 had the most flight hours and cycles since last overhaul of 7,152 h and 2,502 cycles. Engine 4 had the lowest flight hours and cycles since last overhaul of 1,354 h and 369 cycles. For these reasons, three noticeably damaged blades were selected from the high pressure compressor for each of these two engines, and then evaluated at NASA GRC using optical and scanning electron microscopy. Engine 3 compressor blades had both erosion and impact damage that were observed and characterized. The erosion damage was associated with embedded particles 13 μm to 42 μm in sectioned width, composed of varied compositions ranging from SiO2 to SiO2 also containing Ca, Mg, and Al (CMAS). The impact damage was associated with the impacts of larger objects at least 650 μm to 850 μm in width, but only small fragments 5 μm to 15 μm in sectioned width were embedded in the impact surface, also composed of SiO2 to SiO2 containing Ca, Mg, and Al (CMAS). On the other hand, engine 4 blades had only impact damage that was observed and characterized. This impact damage was associated with impacts of objects at least 1,480 μm to 2,080μm in width. Small fragments 5 μm to 15 μm in sectioned width were embedded in the impact surface. For one impact, the fragments were again composed of SiO2 to SiO2 containing Ca, Mg, and Al (CMAS). For two other impacts, the fragments were often composed of Fe, and less frequently Cu.

turbine↗
DOE OSTI2022

Toward the Advanced Manufacturing of Land-Based Wind Turbine Blades: Preprint

The National Renewable Energy Laboratory (NREL) and General Electric (GE) are partners within the Additive and Modular Enabled Rotor Blades and Integrated Composites Assembly (AMERICA) project. AMERICA aims to develop advanced manufacturing solutions to reduce labor and cycle time while increasing recyclability of wind turbine blades. The project is funded by the Advanced Manufacturing Office (AMO) of the U.S. Department of Energy (DOE). This paper describes the techno-economic analysis of the novel manufacturing process applied to the tip of the blade of a representative land-based wind turbine. A comparison to a standard manufacturing process is established, highlighting challenges and opportunities. Several uncertainties affect the analysis, but with the current set of assumptions, the tip adopting advanced manufacturing is predicted to lower labor by 21%, cycle time by 39%, and total blade tip costs by 15% while simultaneously increasing production quality and adopting recyclable thermoplastic resin.

3D printing↗
NASA NTRS1941

Wind-tunnel Tests of Eight-blade Single and Dual-rotating Propellers in the Tractor Position

Tests of 10-ft. diameter, eight-blade, single - and dual - rotating propellers were conducted in 20-ft propeller research tunnel. Propellers were mounted at front end of a streamline body in spinners that covered hubs and parts of shanks. Effect of a symmetrical wing mounted in slipstream was investigated. Blade-angle settings ranged from 20 Degrees to 65 Degrees. Results indicated that dual rotation resulted in gains of from 1 to 8 percent in efficiency over single rotation for eight-blade propellers, but presence of a wing reduced gain about one-half. Greater power absorption caused by dual rotation over flight range and higher efficiency or thrust for range of take-off and climb was indicated

PROPELLER-WING COMBINATIONS↗
NASA NTRS2012

Initial Investigation of the Acoustics of a Counter-Rotating Open Rotor Model with Historical Baseline Blades in a Low-Speed Wind Tunnel

A counter-rotating open rotor scale model was tested in the NASA Glenn Research Center 9- by 15-Foot Low-Speed Wind Tunnel (LSWT). This model used a historical baseline blade set with which modern blade designs will be compared against on an acoustic and aerodynamic performance basis. Different blade pitch angles simulating approach and takeoff conditions were tested, along with angle-of-attack configurations. A configuration was also tested in order to determine the acoustic effects of a pylon. The shaft speed was varied for each configuration in order to get data over a range of operability. The freestream Mach number was also varied for some configurations. Sideline acoustic data were taken for each of these test configurations.

Acoustics↗
DOE OSTI2024

Techno‐Economic Analysis of Additively‐Manufactured Wind Turbine Blade Tips That Enable Technology Integration

The Additively‐Manufactured, System‐Integrated Tip (AMSIT) project is leveraging the flexibility of 3D printing to integrate several technologies in a wind turbine blade tip, while reducing the levelized cost of electricity (LCOE) produced. The design integration is demonstrated for a 200‐kW–scale turbine with 13‐m blades, with the outer 15% of the blade replaced with a 3D‐printed design. Aerodynamic performance is enhanced without increasing swept area through inclusion of a winglet and surface texturing, both challenging for traditional manufacturing. Longevity and durability are improved through integrated lightning and leading edge erosion protection. Increased power, reduced repair frequency, and ease of repair through blade modularity all contribute to reduced LCOE. The analysis is also extended to modern MW‐scale designs to estimate the impact of the technology at scale, demonstrating the potential to reduce LCOE significantly for modern onshore turbines, with even higher potential savings offshore.

3D printing↗
DOE OSTI2021

Controlling Polymer Morphology in Blade-Coated All-Polymer Solar Cells

In this report translating all-polymer solar cells from spin-coating to scalable roll-to-roll-compatible fabrication techniques is a critical step toward the application of organic photovoltaics at a scale. Techniques to control polymer crystallization and phase separation during solution printing are essential to obtain high-performance printed organic solar cells. Here, we demonstrate a novel solvent additive approach employing trace amounts of phthalates as additives to control polymer crystallinity and suppress unfavorable phase separation in a representative PTB7-Th/P(NDI2OD-2T) all-polymer solar cell. The best-performing additive increased the blade-coated device performance from 2.09 to 4.50% power conversion efficiency, an over twofold improvement, mitigating the loss in performance that is typically observed during process transfer from spin-coating to blade-coating. It is suggested that the improved device performance stems from a finer polymer phase-separation size and overall improved active layer morphology, evidenced by device characterization data and indirectly supported by grazing incidence wide-angle X-ray scattering analyses. Real-time X-ray diffraction measurements during blade-coating provide mechanistic insights and suggest that the dioctyl phthalate additive may act as a compatibilizer, reducing the demixing of the donor and acceptor polymer during film formation, enabling a smaller phase separation and improved performance. The structural diversity of the class of phthalate additives makes this simple yet effective concept promising for translating other all-polymer material systems to blade-coating and other scalable printing techniques.

14 SOLAR ENERGY↗