SEARCH · Engineering Papers

Results for “angle control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Flow modifying device

A swirler for a gas turbine engine combustor is disclosed for simultaneously controlling combustor flow rate, swirl angle, residence time and fuel-air ratio to provide three regimes of operation. A first regime is provided in which fuel-air ratio is less than stoichiometric, NOx is produced at one level, and combustor flow rate is high. In a second regime, fuel-air ratio is nearly stoichiometric, NOx production is less than that of the first regime, and combustor flow rate is low. In a third regime, used for example at highoff, fuel-air ratio is greater than stoichiometric and the combustor flow rate is less than in either of the other regimes.

Kelm, J. S.↗

NASA NTRS1985

Precipitation of radiation belt electrons by man-made waves A comparison between theory and measurement

The temporal and spectral shape and the absolute flux level of particle pulses precipitated by a VLF transmitter are examined from a theoretical point of view. A test-particle model of the gyroresonant wave-particle interaction is applied to the parameters of the observed cases for calculating the precipitation characteristics. The temporal shapes of the precipitation pulses are found to be controlled (1) by the pitch angle dependence of the particle distribution near the edge of the loss cone and (2) by the multiple interaction of the particles with the waves due to significant atmospheric backscatter.

Inan, U. S.↗

NASA NTRS1987

Investigation of transonic region of high dynamic response encountered on an elastic supercritical wing

Unsteady aerodynamic data were measured on an aspect ratio 10.3 elastic supercritical wing while undergoing high dynamic response above a Mach number of 0.90. These tests were conducted in the NASA Langley Transonic Dynamics Tunnel. A previous test of this wing predicted an unusual instability boundary based on subcritical response data. During the present test no instability was found, but an angle of attack dependent narrow Mach number region of high dynamic wing response was observed over a wide range of dynamic pressures. The effect on dynamic wing response of wing angle of attack, static outbound control surface deflection and a lower surface spanwise fence located near the 60 percent local chordline was investigated. The driving mechanism of the dynamic wing response appears to be related to chordwise shock movement in conjunction with flow separation and reattachment on both the upper and lower surfaces.

Seidel, David A.↗

NASA NTRS1987

STOL landing thrust: Reverser jet flowfields

Analysis tools and modeling concepts for jet flow fields encountered upon use of thrust reversers for high performance military aircraft are described. A semi-empirical model of the reverser ground wall jet interaction with the uniform cross flow due to aircraft forward velocity is described. This ground interaction model is used to demonstrate exhaust gas ingestion conditions. The effects of control of exhaust jet vector angle, lateral splay, and moving versus fixed ground simulation are discussed. The Adler/Baron jet-in-cross flow model is used in conjunction with three dimensional panel methods to investigate the upper surface jet induced flow field.

Kotansky, D. R.↗

NASA NTRS1987

Investigation of transonic region of high dynamic response encountered on an elastic supercritical wing

Unsteady aerodynamic data were measured on an aspect ratio 10.3 elastic supercritical wing while undergoing high dynamic response above Mach number of 0.90. These tests were conducted in the NASA Langley Transonic Dynamics Tunnel. A previous test of this wing predicted an unusual instability boundary based upon subcritical response data. During the present test no instability was found, but an angle of attack dependent narrow Mach number region of high dynamic wing response was observed over a wide range of dynamic pressures. The effect on dynamic wing response of wing angle of attack, static outboard control surface deflection and a lower surface spanwise fence located near the 60 percent local chordline was investigated. The driving mechanism of the dynamic wing response appears to be related to chordwise shock movement in conjunction with flow separation and reattachment on both the upper and lower surfaces.

Seidel, David A.↗

NASA NTRS1989

Analysis of flight data from a High-Incidence Research Model by system identification methods

Data partitioning and modified stepwise regression were applied to recorded flight data from a Royal Aerospace Establishment high incidence research model. An aerodynamic model structure and corresponding stability and control derivatives were determined for angles of attack between 18 and 30 deg. Several nonlinearities in angles of attack and sideslip as well as a unique roll-dominated set of lateral modes were found. All flight estimated values were compared to available wind tunnel measurements.

Batterson, James G.↗

NASA NTRS1990

The position of the magnetotail neutral sheet in the near-earth region

The position of the near-earth neutral sheet throughout the nightside region between R = 5 R(E) and R = 8.8 R(E) is examined statistically using magnetic field data from AMPTE/CCE. As has been demonstrated previously, the latitudinal position of the neutral sheet is primarily controlled by the dipole tilt angle. The position also depends on local time, radial distance, and magnetic activity. These dependencis may be represented by the empirical formula MLAT = - (0.14 Kp + 0.69) /cos(Phi)/exp 1/3 (0.065 R exp 0.8 - 0.16) DTA, where MLAT is the position in degrees of the neutral sheet relative to the magnetic equator, Kp is the 3-hourly magnetic activity index, Phi is the magnetic local time in degrees (midnight = 0 deg), R is the radius in R(E), and DTA is the dipole tilt angle in degrees.

Lopez, Ramon E.↗

NASA NTRS1991

Wind tunnel investigation of aerodynamic and tail buffet characteristics of leading-edge extension modifications to the F/A-18

The impact of leading-edge extension (LEX) modifications on aerodynamic and vertical tail buffet characteristics of a 16-percent scale F/A-18 model has been investigated in the NASA Langley 30-foot by 60-foot tunnel. Modifications under consideration include variations in LEX chord and span, addition of upper surface fences, and removal of the LEX. Both buffeting and high-angle-of-attack aerodynamics are found to be strongly dependent upon the LEX geometry, which directly influences the strength, position, and breakdown characteristics of the vortex flow field. Concepts aimed at influencing the development of vortical flow field are considered to have much greater potential in design application than those geared toward altering already established flow fields. It is recommended that configuration effects on structural and aerodynamic characteristics be evaluated in parallel, so that trade-off studies can be conducted to ensure adequate structural fatigue life and desired high-angle-of-attack stability and control characteristics in the design of future high performance aircraft.

Shah, Gautam H.↗

NASA NTRS1991

An experimental study of the effects of aft blowing on a 3.0 caliber tangent ogive body at high angles of attack

An experimental study of the effects of aft blowing on the forebody vortex asymmetry over a 3.0 caliber tangent ogive body at high angles of attack was conducted. The tip of the ogive body was equipped with a single blowing nozzle whose position could be adjusted. The tests were conducted in a subsonic wind tunnel at laminar flow conditions. The effects of model roll, angle of attack, blowing coefficient, and blowing nozzle axial position were independently studied. Surface pressure measurements and flow visualization results were obtained. Aft blowing was observed to alleviate the degree of vortex asymmetry at all angles of attack. The blowing was found to be more effective at the higher angles of attack. However, proportional control of the degree of vortex asymmetry was not observed, because the initial flowfield was highly asymmetric.

Gittner, Nathan M.↗

NASA NTRS1992

Full-scale high angle-of-attack tests of an F/A-18

This paper presents an overview of high angle-of-attack tests of a full-scale F/A-18 in the 80- by 120-Foot Wind Tunnel of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center at Moffett Field, California. A production aircraft was tested over an angle-of-attack range of 18 to 50 deg and at wind speeds of up to 100 knots. These tests had three primary test objectives. Pneumatic and mechanical forebody flow control devices were tested at full-scale and shown to produce significant yawing moments for lateral control of the aircraft at high angles of attack. Mass flow requirements for the pneumatic system were found to scale with freestream density and speed rather than freestream dynamic pressure. Detailed measurements of the pressures buffeting the vertical tail were made and spatial variations in the buffeting frequency were found. The LEX fence was found to have a significant effect on the frequency distribution on the outboard surface of the vertical fin. In addition to the above measurements, an extensive set of data was acquired for the validation of computational fluid dynamics codes and for comparison with flight test and small-scale wind tunnel test results.

Meyn, Larry A.↗

NASA NTRS1992

Single link flexible beam testbed project

This thesis describes the single link flexible beam testbed at the CLaMS laboratory in terms of its hardware, software, and linear model, and presents two controllers, each including a hub angle proportional-derivative (PD) feedback compensator and one augmented by a second static gain full state feedback loop, based upon a synthesized strictly positive real (SPR) output, that increases specific flexible mode pole damping ratios w.r.t the PD only case and hence reduces unwanted residual oscillation effects. Restricting full state feedback gains so as to produce a SPR open loop transfer function ensures that the associated compensator has an infinite gain margin and a phase margin of at least (-90, 90) degrees. Both experimental and simulation data are evaluated in order to compare some different observer performance when applied to the real testbed and to the linear model when uncompensated flexible modes are included.

Hughes, Declan↗

NASA NTRS1993

The influence of primary and secondary orientations on the elastic response of a nickel-base single-crystal superalloy

The influence of primary orientation on the elastic response of a (001)-oriented nickel-base single-crystal superalloy, PWA 1480, was investigated under mechanical, thermal, and combined thermal and mechanical loading conditions using finite element techniques. Elastic stress analyses were performed using the MARC finite element code on a square plate of PWA 1480 material. Primary orientation of the single crystal superalloy was varied in increments of 2 deg, from 0 to 10 deg, from the (001) direction. Two secondary orientations (0 and 45 deg) were considered, with respect to the global coordinate system, as the primary orientation angle was varied. The stresses developed within the single crystal plate were determined for each loading condition. In this paper, the influence of the angular offset between the primary crystal orientation and the loading direction on the elastic stress response of the PWA 1480 plate is presented for different loading conditions. The influence of primary orientation angle, when constrained between the bounds considered, was not found to be as significant as the influence of the secondary orientation angle, which is not typically controlled.

Abdul-Aziz, Ali↗

NASA NTRS1992

Aerocapture and aeromaneuvering at Mars

This paper presents the results of a guidance analysis study for aerocapture and aeromaneuvering at Mars. A 4-state, near-optimal, hybrid guidance algorithm is derived for applications throughout the paper. It is based on the critical assumption that Loh's function remains constant between successive guidance updates. Besides the guidance algorithm, the paper presents a performance evaluation of guidance derived from estimated or 'navigated' spacecraft state, provided by an onboard navigation subsystem for real-time applications on Mars. For the performance evaluation, the spacecraft state is augmented by such parameters as the reference atmospheric density and scale-height, the banking angle and angle of attack for spacecraft control and the accelerometer measurement model errors. Finally, the paper examines also, the influence of random uncertainties in atmospheric density on aeroassisted maneuvers, by a Monte Carlo type of simulation.

Vijayaraghavan, A.↗

NASA NTRS1992

Propulsion simulator for magnetically-suspended wind tunnel models

In order to demonstrate the measurement of aerodynamic forces/moments, including the effects of exhaust jets in Magnetic Suspension and Balance System (MSBS) wind tunnels, two propulsion simulator models were developed at Physical Sciences Inc. (PSI). Both the small-scale model (1 in. diameter X 8 in. long) and the large-scale model (2.5 in. diameter X 15 in. long) employed compressed, liquefied carbon dioxide as a propellant. The small-scale simulator, made from a highly magnetizable iron alloy, was demonstrated in the 7 in. MSBS wind tunnel at the University of Southampton. It developed a maximum thrust of approximate 1.3 lbf with a 0.098 in. diameter nozzle and 0.7 lbf with a 0.295 in. diameter nozzle. The Southampton MSBS was able to control the simulator at angles-of attack up to 20 deg. The large-scale simulator was demonstrated to operate in both a steady-state and a pulse mode via a miniaturized solinoid valve. It developed a stable and repeatable thrust of 2.75 lbf over a period of 4s and a nozzle pressure ratio (NPR) of 5.

Joshi, P. B.↗

NASA NTRS1992

On a finite-state inflow application to flap-lag-torsion damping in hover

An aerodynamic model with a coupled set of generalized dynamic wake equations and hybrid equations of motion for an elastic blade are applied here to a two-blade untwisted stiff in-plane hingeless small-scale model rotor with torsionally soft blades. Blade root offset, precone, blade droop, pitch control stiffness, and blade pitch angle are included in the model rotor. Numerical results show that 3D tip relief effects within the nonuniform steady-state inflow are significant to predict steady-state aerodynamic loads and blade deflections. Eigenvalue results confirm the importance of unsteady 3D aerodynamics in predicting lead-lag damping and frequency. Eigenvector analysis correlations reinforced qualitative and quantitative shortcomings associated with quasi-steady 2D aerodynamic theory for aeroelastic applications in hover.

De Andrade, Donizeti↗

NASA NTRS1994

A supercritical airfoil experiment

The purpose of this investigation is to provide a comprehensive data base for the validation of numerical simulations. The objective of the present paper is to provide a tabulation of the experimental data. The data were obtained in the two-dimensional, transonic flowfield surrounding a supercritical airfoil. A variety of flows were studied in which the boundary layer at the trailing edge of the model was either attached or separated. Unsteady flows were avoided by controlling the Mach number and angle of attack. Surface pressures were measured on both the model and wind tunnel walls, and the flowfield surrounding the model was documented using a laser Doppler velocimeter (LDV). Although wall interference could not be completely eliminated, its effect was minimized by employing the following techniques. Sidewall boundary layers were reduced by aspiration, and upper and lower walls were contoured to accommodate the flow around the model and the boundary-layer growth on the tunnel walls. A data base with minimal interference from a tunnel with solid walls provides an ideal basis for evaluating the development of codes for the transonic speed range because the codes can include the wall boundary conditions more precisely than interference connections can be made to the data sets.

Mateer, G. G.↗

NASA NTRS1999

Aerodynamic Characteristics and Development of the Aerodynamic Database of the X-34 Reusable Launch Vehicle

An overview of the aerodynamic characteristics and the process of developing the preflight aerodynamic database of the NASA/ Orbital X-34 reusable launch vehicle is presented in this paper. Wind tunnel tests from subsonic to hypersonic Mach numbers including ground effect tests at low subsonic speeds were conducted in various facilities at the NASA Langley Research Center. The APAS (Aerodynamic Preliminary Analysis System) code was used for engineering level analysis and to fill the gaps in the wind tunnel test data. This aerodynamic database covers the range of Mach numbers, angles of attack, sideslip and control surface deflections anticipated in the complete flight envelope.

Pamadi, Bandu N.↗

NASA NTRS1999

Aerodynamic Characteristics and Development of the Aerodynamic Database of the X-34 Reusable Launch Vehicle

Pamadi , Bandu N.↗