Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “additive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

On the existence of orthorhombic martensite in a near-α titanium base alloy used for additive manufacturing

Additive manufacturing is a state-of-the-art production technology to produce tailor-made and highly complex parts. Among various other alloys, Ti base alloys are frequently used in this manufacturing technique due to their well-balanced properties and their wide range of applications. Allotropic phases and the occurrence of athermal phase transformations are the main reasons why these alloys hold a great development potential and are the basis of extensive use. High cooling rates during manufacturing lead to martensitic phases and the formation of nanometer-sized microstructures resulting in extraordinary strength. Simultaneously, such high cooling rates cause a high amount of lattice defects and the occurrence of residual stresses, which finally may result in delamination effects and cracks. Usually, a common approach to reduce residual stresses during additive manufacturing is to decrease thermal gradients by increasing the heat input or preheating the building platform. Instead of applying the typical approaches to lower thermal gradients, this study deals with the origin of the ‘softer’ orthorhombic martensite by accelerating the solidification process. The implementation of the orthorhombic phase in bulk components was inspired by a new phase transformation herein reported for the first time in the powder material, which also validates the possible occurrence of two martensitic phases in the same alloy. Various sophisticated characterization techniques like high energy and high-temperature X-ray diffraction, high-resolution transmission electron microscopy as well as atom probe tomography were applied to characterize this softer orthorhombic martensitic phase in detail aiming to highlight the opportunities accompanied by this new approach for additive manufacturing of titanium alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase stability in cast and additively manufactured Al-rich Al-Cu-Ce alloys

Additively manufactured (AM) eutectic Al alloy systems have been studied extensively for advantageous thermal stability and mechanical properties due to their refined microstructures. Al-Cu-Ce alloys are one subset of these AM eutectic alloys. Here we studied phase stability in AM Al-Cu-Ce alloys and compared it to that of conventionally cast ones. A new phase, Al 8 Cu 3 Ce, was identified in the microstructures of both AM and cast Al-Cu-Ce alloys. This Al 8 Cu 3 Ce phase was not previously included on experimental or thermodynamically calculated phase diagrams of the Al-Cu-Ce system. Therefore, we performed additional thermodynamic modeling of the system. These models were experimentally validated with cast and subsequently heat-treated Al-Cu-Ce alloys. We found that despite the refined microstructure of the AM alloys, the phases formed were consistent with the cast alloys, suggesting that AM processing did not significantly alter the formation and stability of phases from that in the conventional alloys. In conclusion, this work has resolved inconsistent previous descriptions of the Al-Cu-Ce ternary phase diagram in the Al-rich region and resulted in the addition of the Al 8 Cu 3 Ce as an equilibrium phase above 500 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Heterogeneous phase transformation pathways in additively manufactured Al-Ce-Mn alloys

Heat treatment of additively manufactured Al-Ce based multicomponent alloys leads to complex microstructure evolution. In this research, the ability to extend the phase transformation theories involving nucleation of a product phase from a heterogeneous multi-phase microstructure typical to that of additively manufactured samples is explored. The Al-10Ce-8Mn (wt%) was used as a model alloy system. Under additive manufacturing conditions different solidification microstructures were obtained due to spatial and temporal variations of thermal gradients (G) and liquid-solid interface velocities (R) within a given melt pool. Near the melt pool boundary (high G and low R, referred as MPB region), initially, Al 20 Mn 2 Ce forms from the liquid followed by a eutectic of FCC Al and Al 11 Ce 3 . In the melt pool interiors (low G and high R referred as ES region) a eutectic structure between FCC Al and Al 20 Mn 2 Ce is observed. During subsequent heat treatments, the MPB and ES regions transform into different sets of microstructures. In the MPB region, a fine globular microstructure containing FCC Al, Al 11 Ce 3 , Al 6 Mn, and Al 12 Mn results from the decomposition of Al 20 Mn 2 Ce. In the ES region a faceted Al 51 Mn 7 Ce 4 plate phase results from the decomposition of Al 20 Mn 2 Ce. The formation of the Al 51 Mn 7 Ce 4 phase within the eutectic microstructure at the boundaries of FCC Al and Al 20 Mn 2 Ce has not been reported in the literature. Further, these two distinct phase transformation pathways are rationalized based on the role of driving force on the nucleation of (Al 6 Mn) and/or metastable intermetallic (Al 51 Mn 7 Ce 4 ) phases at the interface of aluminum (FCC) and the non-equilibrium intermetallic (Al 20 Mn 2 Ce) phases.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Multi-material additive manufacturing of aluminum 6061-T6 alloy with stainless steel 304: Suppression of intermetallic compounds and interface growth mechanism

Fabricating integrated aluminum-steel structures is difficult because of metallurgical incompatibilities that promote intermetallic compound (IMC) formation at their interfaces. This work introduces a practical route for additively manufacturing 6061-T6 aluminum alloy (AA6061-T6) directly onto 304 stainless steel (SS304) using a high shear strain rate-assisted interfacial bonding mechanism. Through the friction extrusion deposition-based additive manufacturing method, both single- and multi-layer deposits of AA6061-T6 were successfully fabricated on SS304, yielding a robust hybrid multi-material structure. Comprehensive analyses of deposition quality, interface porosity, and bonding performance showed that the interface achieved a tensile strength exceeding 154 MPa under quasi-static loading. Microstructural observations revealed that the deposited aluminum layers experienced severe plastic deformation, resulting in pronounced grain refinement. Importantly, the interfacial zone was found to be free of brittle IMCs, instead containing a thin amorphous layer that evolved through a non-linear reaction-zone growth law. This solid-state additive strategy establishes a promising pathway for lightweight structural systems, nuclear energy component cladding, and multifunctional engineering components, redefining how dissimilar metals can be integrated for advanced applications.

Aluminum alloy↗
DOE OSTI2014

Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing

Laser powder-bed fusion additive manufacturing of metals employs high-power focused laser beams. Typically, the depth of the molten pool is controlled by conduction of heat in the underlying solid material. But, under certain conditions, the mechanism of melting can change from conduction to so-called “keyhole-mode” laser melting. In this mode, the depth of the molten pool is controlled by evaporation of the metal. Keyhole-mode laser melting results in melt pool depths that can be much deeper than observed in conduction mode. In addition, the collapse of the vapor cavity that is formed by the evaporation of the metal can result in a trail of voids in the wake of the laser beam. In this paper, the experimental observation of keyhole-mode laser melting in a laser powder-bed fusion additive manufacturing setting for 316L stainless steel is presented. Finally, the conditions required to transition from conduction controlled melting to keyhole-mode melting are identified.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Evolution of carbide precipitates in Haynes® 282 superalloy processed by wire arc additive manufacturing

Precipitation hardening regulated with heat treatments is a critical technique for tuning the mechanical properties of Ni-based superalloys fabricated with additive manufacturing, where mechanical deformation is no longer viable for microstructural refinement. As one of the key precipitates, carbides prevail in the additively manufactured alloys, whose precipitation kinetics remain largely vague. This work studies the influence of heat treatments on the evolution of MC- and M 23 C 6 -type carbides within a Haynes® 282 superalloy prepared by wire arc additive manufacturing (WAAM). SEM-EDS analysis was performed to identify the evolution pathways of the carbides, and TEM and XRD characterizations were carried out to track the crystallographic features. The MC-type carbides are originally present in the as-printed alloy, which distribute uniformly across the whole material and remain largely unchanged in size during the heat treatments. By contrast, the incipiently non-existent M 23 C 6 -type carbides precipitate during an aging treatment at 1010 °C, which majorly extend along the grain boundaries as kinetically feasible sites. Further experimental and computational analysis confirms the enhancing effect of the M 23 C 6 -type carbides on the Vickers hardness. For the first time, this work revealed the evolution pathways of carbides within a Haynes® 282 superalloy prepared by WAAM, providing critical information for tunning the microstructure and mechanical properties. Finally, the carbide evolution kinetics established in this work can be potentially extended to other alloys prepared with WAAM, providing critical information to prevent mechanical failures associated with carbide coarsening.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Performance of discontinuity-free components produced by additive turning computer aided manufacturing strategy

Computer aided manufacturing (CAM) techniques for directed energy deposition (DED) affect the material properties of the manufactured component based on the scan strategy used. In this study, we investigate the material characteristics of turning-style toolpath strategies to generate axisymmetric components with additive manufacturing (AM), referred to in this research as additive turning. This novel approach leverages existing CAM technology for turning, where the component rotates around a stationary cutting tool, to generate toolpath trajectories for DED with varying wall-thicknesses and controlled deposition angles. This strategy allows for entire components to be deposited in one continuous deposition, resulting in reduced cycle-time and improved material usage efficiency compared to conventional AM strategies where the beam is switched off at the end of every layer. Results from this study show that the use of additive turning can produce over 99 % dense components with less variation and anisotropy in texture and hardness, as well as a lower variation in elongation to failure when compared to conventional strategies. This research highlights that various CAM strategies could be deployed for AM to improve process efficiency or enable localized control over part performance.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Microstructure and transformation behavior of Ni{sub 24.7}Ti{sub 50.3}Pd{sub 25} high temperature shape-memory alloy with Sc micro-addition

NiTiPd shape-memory alloys (SMAs) are potential functional materials for use as solid-state actuators in the temperature range 100–250 °C. The present study investigates the effect of 1.0 at.% Sc micro-addition to Ni{sub 24.7}Ti{sub 50.3}Pd{sub 25} alloy, Sc replacing either Ti or Ni. Results show that all the three alloys studied have stable transformation behavior on stress-free thermal cycling and hence, are suitable for cyclic actuation applications. However, the addition of Sc to NiTiPd alloy leads to decrease of transformation temperatures, the magnitude of decrease being greater for the alloy with Sc replacing Ni. The martensite finish (M{sub f}) temperature of 181 °C for the NiTiPd alloy decreased to 139 °C for Sc replacing Ti and 83 °C for Sc replacing Ni. Also, the indentation modulus of NiTiPdSc (Sc replacing Ni) alloy is found to be significantly low compared to the other alloys. Analysis indicates that the observed differences in the alloy properties are related to the solubility of Sc in the NiTiPd matrix. While the quaternary NiTiPdSc alloy, Sc replacing Ti, has a single phase microstructure, the alloy with Sc replacing Ni shows the presence of Sc-rich and TiPd-type second phases in the microstructure. TEM examination revealed that the TiPd-type phase has a distinct rod-like morphology (30–50 nm) arranged in a grid-like structure. The transformation and indentation behavior of the alloys is elucidated using thermodynamic calculations of frictional energy and an electronic structure based analysis. - Highlights: • TEM of Ni{sub 23.7}Ti{sub 50.3}Pd{sub 25}Sc{sub 1} showed distinct grid of TiPd-type phase nanorods < 50 nm. • Stress-free thermal cycling of all the three alloys showed stable transformation behavior. • Ni{sub 24.7}Ti{sub 49.3}Pd{sub 25}Sc{sub 1} and Ni{sub 23.7}Ti{sub 50.3}Pd{sub 25}Sc{sub 1} showed single and multiphase structures. • Sc micro-addition (1 at.%) to Ni{sub 24.7}Ti{sub 50.3}Pd{sub 25} alloy decreased TTs significantly. • Ni{sub 23.7}Ti{sub 50.3}Pd{sub 25}Sc{sub 1} exhibited lower modulus of 67 GPa to 85 GPa of Ni{sub 24.7}Ti{sub 50.3}Pd{sub 25}.

36 MATERIALS SCIENCE↗
DOE OSTI2015

The effect of scandium addition on microstructure and mechanical properties of Al–Si–Mg alloy: A multi-refinement modifier

Effect of scandium (Sc) additions on the microstructure, mechanical properties and fracture behavior of Al–Si–Mg casting alloy (F357) were systematically investigated. It was found that Sc addition caused a multi-refining efficiency on the microstructure of as-cast F357 alloy, including refinement of grains and secondary dendrite arm spacing (SDAS), modification of eutectic Si and harmless disposal of β-Al{sub 5}FeSi phase. Subsequent T6 heat treatment had further induced the complete spheroidization of eutectic Si and precipitation of fine secondary Al{sub 3}Sc dispersoids in the Sc modified alloys. Thus the mechanical properties, especially the ductility, were significantly enhanced by the addition of Sc combined with the heat treatment. The highest ultimate tensile strength, yield strength and elongation were achieved in 0.8 wt.% Sc modified F357 alloy combined with T6 heat treatment. Furthermore, fractographic examinations indicated that the ductile fracture mechanism served as a dominate role in the modified alloys due to the formation of fine, deep and uniformly distributed dimples. - Highlights: • Detailed characterization of the multi-refining microstructure of Sc modified F357 alloy was performed. • The multi-refinement was proposed to refine grain and SDAS, modify eutectic Si and β-phase. • Sc modifier combined with T6 treatment is effective in improving tensile properties. • Modification of eutectic Si in F357 alloy with Sc is consistent with the IIT mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Effect of Ag additions on the lengthening rate of Ω plates and formation of σ phase in Al-Cu-Mg alloys during thermal exposure

Effect of Ag additions on the mechanical properties and microstructures of the peak-aged Al-Cu-Mg alloys during prolonged thermal exposure at 150 °C, was investigated by tensile testing, conventional transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM). The results showed that after exposure for 500 h, > 85% of the peak strength remained. Microstructure observations indicated that increasing the Ag content from 0.14 to 0.57% promoted the precipitation of a fine and uniform Ω phase and suppressed the formation of the θ′ phase, leading to a notable improvement of the strength properties and thermal stability of the studied alloys. Quantitative TEM analysis showed that the coarsening of Ω phase was predominated by plate lengthening rather than thickening, while its lengthening rate was independent of various Ag additions during exposure at 150 °C. In addition, an increase of Ag also facilitated the formation of a cubic σ phase, which was further supported by STEM results. - Highlights: •Increasing Ag improved strength properties and thermal stability of the alloys. •After exposure for 500 h, > 85% of the peak strength remained. •The lengthening rate of Ω plates remained constant as Ag increased at 150 °C. •Increasing Ag content facilitated the formation of σ phase.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The effect of boron addition on the deformation behavior and microstructure of β-solidify TiAl alloys

Highlights: • Borides could promote the DRX formation to soften TiAl alloys. • Boron addition increases firstly and then stabilizes the deformation activate energy. • The stable region expands with boron increasing in processing maps. • The DRX critical strain increases firstly and then decreases with boron increasing. • DRX softening and strengthening from solid solution and borides influence deformation behavior. - Abstract: The effect of boron addition on the deformation behavior and microstructure of Ti-43Al-6Nb-1Mo -1Cr alloys have been studied in this paper. Boron addition would induce Ti{sub 2}Al(P6{sub 3}/mmc) phase with hexagonal structure formation on the interfaces between TiB and γ phase. TiB would be the obstacles for dislocations slipping and increase the stacking fault energy. Ti{sub 2}Al could also provide the chemical foundation for DRXed γ nucleation and disappear after thermal deformation. Both these two phase could promote DRXed grains nucleation to soften the alloys during thermal deformation. With the strengthen effect of boron solid solution and TiB obstacles, the microstructure evolution, phase transformation and deformation behavior are also discussed and concluded as follow.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Direct measurement of the effective properties of an additively manufactured titanium octet truss unit cell using high energy X-ray diffraction

Additively manufactured lattice structures offer a high specific strength-to-density ratio in comparison to conventional, fully dense parts. The small feature size and intricate geometry of lattice structures make it challenging to directly characterize their mechanical properties. This study presents direct measurement of the elastic mechanical properties of an additively manufactured titanium alloy octet truss unit cell. Strut stress and strain were measured using high-energy X-ray diffraction during quasi-static compressive loading. The crystallographic stress-strain relationship was converted into the stress-strain relationship of the octet truss lattice unit cell using the known symmetry of the struts. The sample studied herein was best fit by an orthorhombic linear elastic stress-strain relationship. In conclusion, this technique shows promise for studying additively manufactured lattice structures at length scales not previously reported.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Complex shaped boron carbides from negative additive manufacturing

In this paper, complex shaped boron carbide with carbon (B 4 C/C) at near-full densities were achieved for the first time using negative additive manufacturing techniques via gelcasting. Negative additive manufacturing involves 3D printing of sacrificial molds used for casting negative copies. B 4 C powder distributions and rheology of suspensions were optimized to successfully cast complex shapes. In addition to demonstrating scalability of these complex geometries, hierarchically meso-porous structures were also shown to be possible from this technique. Resorcinol-Formaldehyde (RF) polymer was selected as the gelling agent and can also pyrolyze into a carbon aerogel network to act as the sintering aid for B 4 C. Finally, due to the highly effective distribution of in situ carbon for the B 4 C matrix, near-full sintered density of 97–98% of theoretical maximum density was achieved.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Solid additive engineering enables high-efficiency and eco-friendly all-polymer solar cells

Currently, morphology optimization of all-polymer solar cells (all-PSCs) strongly depends on the use of solvent additives, which are usually highly toxic and harmful to the environment and human health. Here, we report a green and volatile solid additive, 2-methoxynaphthalene (2-MN). It was found that the incorporation of 2-MN into a PM6:PY-DT blend can effectively manipulate the aggregations of PM6 and PY-DT during film depositing and thermal annealing processes and results in highly ordered molecular packing and favorable phase-separated morphology. Consequently, a record-high efficiency of 17.32% is achieved for the PM6:PY-DT device. Moreover, 2-MN-processed all-PSCs were fabricated by using non-halogenated solvent. High efficiencies of 17.03% and 16.67% are obtained for all-PSCs fabricated under nitrogen atmosphere and ambient conditions, respectively. Finally, our work shows that the utilization of 2-MN as a green and solid additive is a simple and feasible strategy to optimize the morphology and sheds new light on eco-friendly fabrication and application of all-PSCs.

14 SOLAR ENERGY↗
DOE OSTI2021

A critical review and commentary on recent progress of additive manufacturing and its impact on membrane technology

Membrane separations has been increasingly recognized as a key technology platform for improving the energy efficiency of many separations processes. Likewise, additive manufacturing (AM), or 3-dimensional (3D) printing as it is often called, is a rapidly emergent technology platform for manufacturing in many industrial sectors. It has become increasingly common to marry these two platforms to take advantage of the additive nature of 3D printing with the increasing need for membrane technology that is adaptable to separations needs. Conventional membrane manufacturing approaches, such as casting, typically result in thick membranes that limit productivity and potentially waste material in a non-performing support layer. Interfacial polymerization (IP) offered a new vision for thin-film composite desalination membranes, yet it was limited to certain chemistries while exhibiting other drawbacks. Additive manufacturing offers certain benefits over these techniques to membranes, including the ability to expand the library of materials that can be processed while also offering a degree of customization that is impossible in conventional manufacturing. This review article evaluates an increasing body of literature on using printing to make membranes and considers the limitations and opportunities for printing to enhance existing membrane technology and expand the reach of membranes into other industries. Furthermore, we also provide a perspective from leading experts in membrane technology to see where there are opportunities to use printing in different membrane science disciplines.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Joining technique for in-oven/autoclave molds manufactured by large scale polymer additive manufacturing

Large scale additive manufacturing (AM) of fiber-reinforced polymer composites has gained traction in the mold and die community over the last decade, largely due to reduced material cost and lead time. However, limitations in mold size remain present due to printer volume constraints and costs associated with large format machines. Here, this paper describes a method for producing additively manufactured polymer molds in segments with an O-ring joint design, which can be machined and subsequently assembled for autoclave applications. The developed joining mechanism allows for maintaining the vacuum integrity during the cure cycle while accounting for the anisotropic nature of the additively manufactured polymer molds. Over a range of tested temperatures, 20–200 °C, the multi-part mold joining design was able to achieve full vacuum of ∼73.7 cmHg (29 inchHg) and maintain a vacuum integrity with vacuum losses less than 1.5 cmHg/5min (0.6 inchHg).

Joining↗
DOE OSTI2022

The performance of additively manufactured Haynes 282 in supercritical CO 2

The use of supercritical carbon dioxide (sCO 2 ) as a working fluid is garnering interest in next generation power production systems due to the possibility of increased operational efficiencies and lower associated costs. Its implementation requires alloys with excellent high temperature strength and corrosion resistance, which makes Haynes 282® (H282) a suitable candidate. With increasing adoption of additive manufacturing (AM) in the energy industry, there is a need to investigate long-term sCO2 exposure on AM produced materials. Additively manufactured H282 (AM-H282) samples built using laser powder bed fusion in two different orientations were analyzed through imaging, gravimetric analysis, and room-temperature tensile testing before and after 1000-h exposure to CO 2 at 750 °C and 20 MPa. Performed imaging included observation of the sample surfaces and of the material bulk (cross sections) through means of Scanning Electron Microscopy (SEM) and optical microscopy. In comparison to wrought H282, it was found that the exposed material exhibited a similar Cr 2 O 3 oxide protective layer about 2 μm in thickness with additional top-surface TiO 2 oxide and carbon-rich precipitates. It was also similarly observed that internal oxidation was present but limited to a depth of 20 μm, and a 1–3 μm γ’ denuded region appeared to surround all internal and surface oxidation. Thermal aging effects were noted with the precipitation of needle-like structures in the γ/γ’ matrix and a coarsening of the γ’ precipitates from 28 nm to 73 nm. Mass measurements analyzing oxide precipitation revealed a larger increase compared to wrought, representing an approximate 20% difference. Tensile testing results showed similar behavior to wrought with a slight increase in yield strength and a large reduction in elongation in the exposed samples.

36 MATERIALS SCIENCE↗