Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “UNLOADING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

The influence of crack closure and elasto-plastic flow on the bending of a cracked plate

The influence of crack closure and elastoplastic flow on the bending behavior of thin cracked plates is investigated using an incremental elastoplastic plate bending finite element computer program. The finite element program was developed using assumptions consistent with Kirchhoff fourth-order plate theory while the material property treatment permits general isotropic work hardening with local elastic unloading. This technique is applied to the problem of a large centrally through cracked plate subject to remote circular bending. Comparison is drawn between two cases of the bending problem. The first neglects the possibility of crack face interference with bending, and the second includes a kinematic prohibition against the crack face from passing through the symmetry plane. Results are reported which isolate the effects of elastoplastic flow and crack closure.

Jones, D. P.↗

ATS-6 - Quartz-Crystal Microbalance

The Quartz-Crystal Microbalance Experiment provided data on the possible return of contaminants to the exterior surfaces of the spacecraft. The experiment measures the change in resonant frequency of the crystal due to deposition of material on the surface. There has been no mass accretion corresponding to the firing of hydrazine thrusters to unload the spacecraft momentum wheels. There have been accretions corresponding to the firing of the cesium ion engines.

Rogers, J. F.↗

Severe storms observing satellite study

Payload distribution and the attitude control system for the multi-mission modular spacecraft/StormSat configuration are discussed. The design of the advanced atmospheric sounder and imaging radiometer (AASIR) gimbal drive and its servomechanism is described. Onboard data handling, data downlink communications, and ground data handling systems are developed. Additional topics covered include: magnetic unloading at synchronous altitude, north-south stationkeeping, and the feasibility and impact of flying the microwave atmospheric sounding radiometer (MASR) as an additional payload.

Iwens, R. P.↗

Industrial robots in Europe - market, applications and developments

Different companies involving a wide range of products and manufacturing processes were studied to define the requirements for industrial robots. A survey of all such automatic units offered on the world market was made to establish a data base. Principal applications include coating, spot welding, and loading and unloading operations.

Schraft, R. D.↗

Wide angle pinhole camera

Hemispherical refracting element gives pinhole camera 180 degree field-of-view without compromising its simplicity and depth-of-field. Refracting element, located just behind pinhole, bends light coming in from sides so that it falls within image area of film. In contrast to earlier pinhole cameras that used water or other transparent fluids to widen field, this model is not subject to leakage and is easily loaded and unloaded with film. Moreover, by selecting glass with different indices of refraction, field at film plane can be widened or reduced.

Franke, J. M.↗

Tensile stress-strain behavior of boron/aluminum laminates

The tensile stress-strain behavior of five types of boron/aluminum laminates was investigated. Longitudinal and transverse stress-strain curves were obtained for monotonic loading to failure and for three cycles of loading to successively higher load levels. The laminate strengths predicted by assuming that the zero deg plies failed first correlated well with the experimental results. The stress-strain curves for all the boron/aluminum laminates were nonlinear except at very small strains. Within the small linear regions, elastic constants calculated from laminate theory corresponded to those obtained experimentally to within 10 to 20 percent. A limited amount of cyclic loading did not affect the ultimate strength and strain for the boron/aluminum laminates. The laminates, however, exhibited a permanent strain on unloading. The Ramberg-Osgood equation was fitted to the stress-strain curves to obtain average curves for the various laminates.

Sova, J. A.↗

Core compressor exit stage study. Volume 1: Blading design

A baseline compressor test stage was designed as well as a candidate rotor and two candidate stators that have the potential of reducing endwall losses relative to the baseline stage. These test stages are typical of those required in the rear stages of advanced, highly-loaded core compressors. The baseline Stage A is a low-speed model of Stage 7 of the 10 stage AMAC compressor. Candidate Rotor B uses a type of meanline in the tip region that unloads the leading edge and loads the trailing edge relative to the baseline Rotor A design. Candidate Stator B embodies twist gradients in the endwall region. Candidate Stator C embodies airfoil sections near the endwalls that have reduced trailing edge loading relative to Stator A. Tests will be conducted using four identical stages of blading so that the designs described will operate in a true multistage environment.

Wisler, D. C.↗

Fatigue damage in notched composite laminates

This communication describes the results of an experimental investigation of the fatigue characteristics of a boron-epoxy laminate containing an unloaded circular hole. The study focuses upon characterization of the fatigue damage incurred and its influence upon axial tensile residual strength. Two apparent anomalies in the fatigue behavior for this laminate were observed. First, the fatigue damage was observed to propagate tangentially to the edge of the notch (parallel to the direction of the load), in contrast to propagation in contemporary metallic materials which is perpendicular to the load direction. Second, the residual strength characteristics for the laminate have revealed a significant increase in residual strength subsequent to a fatigue loading of 500,000 cycles at R = 0.1 and S = 0.8 and 0.67 (S = maximum stress/static ultimate). Failure analyses of the fatigue damage are conducted utilizing ultrasonic 'C' scan techniques.

Pipes, R. B.↗

An experimental investigation on the tensile moduli and strengths of graphite/epoxy laminates

The results of a series of tensile tests on some graphite/epoxy laminates, at rates varying from 0.002 to 2 in./min are examined. The loads were applied at various angles to the fiber directions in each case. The rate-dependent behavior of the stress-strain response is assessed. Evidence is presented to indicate that failure first occurs on inner plies, and that, in some cases, moduli increase with increasing stress (or strain) level. Lamination theory is used to predict the moduli, and comparisons with experiment are given. This theory is also used in conjunction with three failure theories to predict ultimate strengths (with varying degrees of success). Further, two approaches to ply unloading after first-ply failure are used and discussed. One is a standard method found in the literature while the other is a proposed 'strength-of-materials' type of technique which is computationally much simpler.

Yeow, Y. T.↗

Considerations of crack growth and plasticity in finite element analysis

A finite-element analysis was made of crack growth in a center-cracked specimen subjected to monotonically increasing load until the point of fast fracture. Since part of the specimen experienced unloading, the boundary value problem which was formulated was based upon incremental theory of plasticity. Experimental load and crack size records were utilized. Linear relations between plastic energy and crack growth were observed. Fracture toughness parameters, which were evaluated at the onset of unstable crack propagation from finite-element analysis, were in good agreement with those determined experimentally.

Lee, J. D.↗

Attitude control algorithms for the Solar Maximum Mission

Algorithms for onboard attitude control of the Solar Maximum Mission (SMM) are discussed and test results are presented. The algorithms include: despin and sun acquisition, control of pitch and yaw (sun pointing) to 5 arc-sec accuracy and roll (around the sun line) to 0.1 deg, time-optimal and constant-rate slew sequences, attitude maintenance during orbit night and sun reacquisition at orbit dawn, momentum unloading, and gyro drift calibration. The tests were performed on the SMM Software Development and Validation Facility at the NASA Goddard Space Flight Center with a FORTRAN prototype version of the onboard software.

Markley, F. L.↗

Remote manipulator for IC wafers

Mechanical manipulator automatically loads, transports, and unloads silicon wafers between processing stations in large-scale integrated-circuit fabrication facility at Marshall Space Flight Center thus eliminating need for human opeators at various stages in processing cycle. It also reduces possibility of wafer contamination.

Hudgins, J. L.↗

A study of canard-wing interference using experimental pressure data at transonic speeds

The canard had an exposed area of 28.0 percent of the wing reference area and was located in the chord plane of the wing or in a position 18.5 percent of the wing mean geometric chord above or below the wing chord plane. The canard leading edge sweep was 51.7 deg and the wing leading-edge sweep was 60 deg. The results indicated that the direct canard downwash effects on the wing loading are limited to the forward half of the wing directly behind the canard. The wing leading-edge vortex is located farther forward for the wing in the presence of the canard than for the wing-alone configuration. The wake, from the canard located below the wing chord plane, physically interacts with the wing inboard surface and produces a substantial loss of wing lift. For the Mach number 0.70 case, the presence of the wing increased the loading on the canard for the higher angles of attack. However, at Mach numbers of 0.95 and 1.20, the presence of the wing had the unexpected result of unloading the canard.

Gloss, B. B.↗

Definition of Mutually Optimum NDI and Proof Test Criteria for 2219 Aluminum Pressure Vessels. Volume 2: Optimization and Fracture Studies

Certain behavioral aspects associated with fracture and crack extension that cannot be studied using other techniques were evaluated with the ultrasonic method. Characterization of collimated beam techniques showed that significant beam width reduction could be accomplished. Techniques for collimation are given. The crack-opening displacement-gage correction-factor study showed that displacement resulting from crack opening and that from plasticity could be readily differentiated. Crack closure studies using both ultrasonic and crack-opening displacement measurements showed an opening and closing behavior associated with load-unload curves. The results of this work were in general agreement with the closure concepts of Elber. Ultrasonic measurements used to study the nature of flaw extension characteristics associated with failure of the ligament between the flaw front and back surface showed that penetration could occur by an abrupt fracturing after subcritical growth or by continuous growth.

Schwartzberg, F. R.↗

Gimbal bearing design considerations and friction control

The design considerations of bearing selection, bearing fits, bearing installation, and thermal control are discussed for a gimbal with a high stiffness, low friction torque requirement. Tradeoffs between a quad set of small diameter spread apart or a large diameter bearing pair resulted in a cleaner, lighter, stiffer unit with the latter selection. Bearing fits were designed to eliminate clearances with tolerances of .00127 mm 00005 in) on the bearing shafts and housings. The problems in metrology are discussed and a perferred technique for measurement of small cross-section bearings described. A technique for installation to assure proper seating of the bearing is offered. Where transient thermal conditions are involved, a method of controlling bearing friction by active control of bearing temperature gradients including the use of bearing unload test curves is described.

Kramer, N. R.↗

Twin jet noise shielding for a supersonic cruise vehicle

An engine arrangement for a supersonic cruise vehicle (SCV) has been developed that shows promise for jet noise reduction without the performance penalties associated with mechanical suppressors and engine oversizing. This arrangement, wherein two engines are placed on top of the wing directly above two similarly-mounted engines below the wing, can produce 3 to 5 dB less noise below the aircraft flight path than when four engines are installed under the wing. This noise reduction is due to acoustic shielding of the upper jets by the lower jets. Test data are reviewed to verify this acoustical shielding phenomenon, and detailed takeoff trajectories are calculated to show the effects of sideline and flyover noise levels on constraining maximum range SCV configurations. Engine placement variation and differential throttling, wherein thrust is unloaded from the lower engine and added to the upper engine, are to be explored as means for maximizing the shielding effect.

Clauss, J. S., Jr.↗

An automated oxide and diffusion facility for IC's

Report discusses totally-automated oxidation and diffusion facility for fabricating IC's. Several innovations are demonstrated: process controller specifically designed for semiconductor processing; automatic loading system to accept wafers from air track, insert them in quartz carrier, and place carrier on paddle for insertion into furnace; automatic unloading of wafers back onto air track; and boron diffusion using diborane.

Kennedy, B. W.↗

Storage peak gas-turbine power unit

A storage gas-turbine power plant using a two-cylinder compressor with intermediate cooling is studied. On the basis of measured characteristics of a .25 Mw compressor computer calculations of the parameters of the loading process of a constant capacity storage unit (05.3 million cu m) were carried out. The required compressor power as a function of time with and without final cooling was computed. Parameters of maximum loading and discharging of the storage unit were calculated, and it was found that for the complete loading of a fully unloaded storage unit, a capacity of 1 to 1.5 million cubic meters is required, depending on the final cooling.

Tsinkotski, B.↗