Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Titanium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Mechanical Properties and Microstructure Evolution During Bending–Unbending Deformation of Pure Titanium Sheet

In this study, the pure titanium sheets with thickness of 1 mm are deformed 1-5 times in the form of bending–unbending cyclic deformation. The bending angles before and after unbending are 120° and 180°, respectively. Mechanical properties of samples during cyclic deformation, including M/(BH){sup 2}-surface strain curve and spring back in each bending cycle, have been investigated. Moreover, the twinning/detwinning behavior and texture evolution in three typical bending layers (i.e., the tensile layer, neutral layer and compressive layer) in cyclic deformation have been tested by EBSD and TEM, and analyzed systematically. The results indicate that the most intensive twins, consist of similar proportion of tensile and compressive ones, distribute in the inner layer after 1st bending. While they disappear almost entirely after 1st unbending. The twins in outer layer could also be detwinned, and the new twins could be activated during 1st unbending. Besides, the twin density increases obviously and the residual twins could not be detwinned clearly after multiple passes of cyclic deformation. Moreover, the Schmid factor along the σ{sub 2} direction functions in the activation of twin variants regardless of the three-direction stress states.

36 MATERIALS SCIENCE↗

Effect of Cold Rolling and Heat Treatment on Microstructure and Mechanical Properties of Ti-4Al-1Mn Titanium Alloy

Mechanical behavior of Ti-4Al-1Mn titanium alloy has been studied in annealed, cold-rolled and heat-treated conditions. Room temperature tensile strength as well as % elongation has been found to be low with increasing amount of cold rolling. Lowering of strength in cold worked condition is attributed to premature failure. However, the same has been mitigated after heat treatment. Significant effect of cooling media (air and water) from heat treatment temperature on microstructure was not found except for the degree of fineness of α plates. Optimum properties (strength as well as ductility) were exhibited by samples subjected to 15% cold rolling and heat treatment below β transus temperature, which can be attributed to presence of recrystallized microstructure. In cold worked condition, the microstructure shows fine fragmented α plates/Widmanstätten morphology with high dislocation density along with a large amount of strain fields and twinning, which gets transformed to recrystallized equiaxed microstructure and with plate-like morphology after near β heat treatment. Prior cold work is found to have a significant effect on mechanical properties supported by evolution of microstructure. Twinning is found to be assisting in deformation as well as in recrystallization through the formation of deformation and annealing twins during cold working and heat treatment. Fracture analysis of the tested sample with prior cold work and heat-treated condition revealed quasi-ductile failure as compared to only ductile failure features seen for samples heat treated without prior cold work.

36 MATERIALS SCIENCE↗

Fatigue Properties of Ti-6Al-4V Titanium Alloy Friction Stir Welding Joint

Friction stir welding was used to consolidate 2-mm-thick Ti-6Al-4V titanium alloy sheets, and the static and fatigue properties of the joint were investigated. The results reveal that uniform microhardness distribution of the nugget zone (NZ) after post-weld heat treatment was associated with the uniform equiaxed microstructure of the NZ. The joint fatigue limit predicted by the S–N curve reached 640.84 MPa, up to 64.76% of joint tensile strength. Fatigue specimens fractured at the transition zone between the base material and NZ, and the positions of fatigue crack initiation sites were relatively random. The fracture surface of the fatigue crack propagation region was composed of radial strips and striations, and numerous dimples were observed on the final fast fracture surface.

36 MATERIALS SCIENCE↗

Effect of Heat Treatment and Combination of Cold Rolling and Heat Treatment on Microstructure and Mechanical Properties of Titanium Alloy Ti6Al2V2Zr1.5Mo

The heat treatment and cold rolling combinations have been carried out on titanium alloy Ti6Al2V2Zr1.5Mo, and microstructure evolution and mechanical behavior have been studied. Solution treatment below the β-transus temperature, followed by air cooling, resulted in higher microhardness/strength as compared to the same with water quenching. A sudden drop in microhardness/strength is observed in sample solution heat-treated above β-transus temperature followed by air cooling. The former is attributed to the additional presence of fine secondary α-phase formed by dynamic aging during air cooling as compared to water-quenched samples which did not have fine secondary α-phase. Solution treatment above β-transus temperature resulted in Widmanstatten microstructure with no significant fine secondary α in air-cooled samples. Among the studied conditions of cold rolling (CR), gain in strength of the alloy from annealed condition is significant with first 15% reduction and thereafter it is marginal for 30% reduction. Initiation of cracks at the edges has been observed in 30% CR. The microstructure of cold-rolled samples confirms the fragmentation of α-plates with the presence of high dislocation density. Heat treatment of cold-rolled samples resulted in significant reduction in strength from the as-cold-rolled conditions. The marginally lower strength than the as-received (annealed) or heat-treated alloy samples is due to the recrystallization in CR samples and the formation of Widmanstatten microstructure in air-cooled samples. The alloy does not have fine secondary α or regions with large dislocation density in this condition. The microstructure in the samples heat-treated (with air cooling) below as well as above β-transus temperature (after CR) is similar to air-cooled samples (without prior CR) with heat treatment above β-transus temperature. This indicates the reduction in recrystallization temperature with cold working, which is substantiated with the reduction in strength as well.

36 MATERIALS SCIENCE↗

Effect of Surface Self-Nanocrystallization on Diffusion Bonding Between a Titanium Alloy and a TiAl-Based Alloy

A self-nanocrystallization layer was prepared on the surface of a Ti alloy sample via shot peening to investigate its influence on the follow-up diffusion bonding between a titanium alloy and a TiAl-based alloy. The experiment results show that surface self-nanocrystallization treatment can accelerate the interface reaction between a Ti alloy and a TiAl alloy, lowering the bonding temperature of the sound joints by more than 50 K. Moreover, the thickness of the interface reaction layer plays an important role in the interfacial bonding strength. In this work, the maximum shear strength of the joint appears to have a thickness of about 1.8 μm. As a consequence, it is found that surface self-nanocrystallization treatment is helpful for optimizing the diffusion bonding process.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Creep Behavior of Commercially Pure Titanium TA2 After Supersonic Fine Particles Bombardment

In this study, the effect of supersonic fine particles bombardment (SFPB) on the creep behavior of commercially pure titanium TA2 was investigated. Microstructural observations with x-ray diffraction and a transmission electron microscope indicated that the grain size of the TA2 surface layer was refined to nanometer scale in the topmost surface layer after SFPB treatment. Indentation creep tests showed that the SFPB-treated sample had a lower maximum depth and higher hardness than the original sample at the same load, indicating an enhancement of the surface strength with SFPB. With lower creep displacements, the creep resistance was also improved after SFPB treatment. The maximum creep rate under different loading conditions showed obvious loading time and load dependencies. The maximum creep rate of the SFPB-treated sample was lower than the original sample for all test conditions, and the maximum creep strain rate of the SFPB-treated sample was similar to that of the original sample. The indentation stress of the SFPB-treated sample was higher than the original sample, while the creep stress exponent of the original sample was slightly higher than for the SFPB-treated sample, with no obvious variation tendency with different loading times or loads.

36 MATERIALS SCIENCE↗

Study on Tensile Deformation Behavior of TC21 Titanium Alloy

To investigate the tensile deformation behavior of TC21 titanium alloy wires, the isothermal tensile deformation tests were conducted by a Geeble-1500D simulator in the temperature range of 720-880 °C and strain rates of 0.01-10 s{sup −1}. The in situ tensile deformation behavior has been studied by SEM SURPA40. The stress–strain curves indicate that the flow stress has shown an inverse relationship with temperature and a direct relationship with strain rate. The flow stress immediately reached the peak value and, then, gradually decreased due to the dynamic softening induced by dynamic recovery and dynamic recrystallization. According to the hot processing maps, the temperatures ranging from 720 to 760 °C (corresponding to the strain rates of 0.01-0.032 s{sup −1}) and 800-840 °C (corresponding to the strain rates of 0.01-0.056 s{sup −1}) are suitable for processing. The in situ tensile results reveal that the cracks initiated at the pre-fabricated defects with the concentrated stress and mainly propagated in the transgranular mode.

36 MATERIALS SCIENCE↗

Role of Titanium, Carbon, Boron, and Zirconium in Carbide and Porosity Formation during Equiaxed Solidification of Nickel-Based Superalloys

This work analyses the effect of Ti in the MC carbide formation and also in the γ/γ´ eutectic promotion in two nickel-based alloys melted under vacuum conditions and solidified into ceramic molds. The role of boron, carbon and zirconium on the porosity level after solidification of both alloys was also investigated; since the alloys were vacuum melted, it is assumed that the observed porosity is due to micro-shrinkage. The chemical compositions for two alloys were: 20.2Cr-13.7Co-4.78Mo-1.19Al-0.69Ti-0.08C-2.34Fe for Alloy 1, and 20.5Cr-15.6Co5.03Mo-1.57Al-3.42Ti-0.15C-1.64Fe-0.076Zr-0.01%B for Alloy 2. Results showed a higher volume fraction of MC carbides and the γ/γ´ eutectic for the Alloy 2 with higher titanium content since this element is a carbide and γ/γ´ eutectic promoter. The porosity level in the Alloy 2, with higher amounts of carbon, boron and zirconium was considerably lower than that for the Alloy 1. These results are discussed in terms of different phenomena caused by the segregating effects of boron, carbon and zirconium towards the interdendritic regions and the formation of zirconium carbides that produce an expansion in volume when they are formed at the end of the solidification process.

36 MATERIALS SCIENCE↗

Correlation between Antimicrobial Activity and Bioactivity of Na-Mica and Na-Mica/Fluorapatite Glass and Glass-Ceramics and Their Corrosion Protection of Titanium in Simulated Body Fluid

The improvement in bioactivity of titanium (Ti) surface was achieved via coating it with Na-mica and Na-mica/fluorapatite glass and glass-ceramic using the low-cost electrophoretic deposition technique. Two compositions from pure Na-mica (M) and 80 Na-mica/20 fluorapatite glasses (MF) were prepared in the system SiO{sub 2}-Al{sub 2}O{sub 3}-MgO-MgF{sub 2}-Na{sub 2}O-B{sub 2}O{sub 3} using melting–quenching technique. Characterization of the as-prepared glasses and their counterpart glass-ceramics was studied using differential thermal analysis (DTA), x-ray diffraction (XRD), Scanning Electron Microscopy (SEM) and Fourier Transform-IR (FTIR) spectroscopy techniques. The bioactivity behavior was proved by studying the XRD, FTIR and SEM after immersing both glass and glass-ceramic samples in simulated body fluid (SBF). Both M and MF glasses and glass-ceramics showed high microhardness measurements and good antibacterial behavior. In vitro biodegradation was studied by using electrochemical corrosion behavior of the prepared glass- and glass-ceramic-coated Ti in SBF. The prepared coated Ti showed good corrosion resistance in SBF at 37 °C using potentiodynamic polarization technique, and the impedance data fitting explained the structure of the coating and the adsorption of SBF ions on the Ti surface. The MFGC provides the best corrosion-resistant coating, especially after sintering it.

36 MATERIALS SCIENCE↗

Constitutive Modeling for Hot Working Behavior of SP-700 Titanium Alloy

In this paper, the constitutive modeling and hot deformation behavior of SP-700 titanium alloy was investigated by performing isothermal hot compression tests in the temperature range of 700-950 °C and strain rates of 0.001, 0.1, and 1 s{sup −1}. The flow curves of the alloy indicated that the yield point phenomenon occurs at strain rates of 0.1 and 1 s{sup −1}. The friction, adiabatic heating, and stroke-rate controlling effects were eliminated from the raw data. Then, three types of phenomenological constitutive models, considering the compensation of strain, were used to predict the flow stresses of the alloy. The correlation coefficients (R{sup 2}) of the measured and predicted results for the power-law, hyperbolic-sine law, and dynamic softening models were found to be 0.9790, 0.9883, and 0.9877, respectively. The corresponding average absolute relative errors (AARE) were 6.3, 5.9, and 7.45%, respectively. The flow softening behavior of SP-700 alloy was modeled using the combined hyperbolic-sine law and dynamic softening model approach. The predicted flow stresses were in a good agreement with the experimental data, indicated that the developed models can accurately characterize flow behavior of the alloy. In addition, the strain-rate sensitivity (m) distribution map of the alloy was obtained by plotting the m-value against temperature and strain rate in the form of a contour map. There was the maximum of m-value (0.36) in the temperature ranges of 700-715 and 837-875 °C, and strain rates of 0.001-0.006 s{sup −1}. The microstructure of hot deformed at 700 °C mainly consists of globularized and lamellar α phase, while dynamic globularization was completed at 800 °C. The hot deformation activation energy of the alloy in α/β region (305.5 kJ mol{sup −1}) was higher than that in single-phase β region (165.2 kJ mol{sup −1}) due to the globularization of lamellar α.

36 MATERIALS SCIENCE↗

Effect of Solution Treatment on the Microstructure, Micromechanical Properties, and Kinetic Parameters of the β → α Phase Transformation during Continuous Cooling of Ti-6Al-4V Titanium Alloy

The aim of this study is to examine the effect of solution treatment temperature (STT) on the microstructure, the micromechanical properties, and the kinetic parameters of the β → α phase transformation during continuous cooling of the dual phase titanium alloy Ti-6Al-4V. Increasing the STT from 1050 to 1200 °C delays the formation of the α phase during cooling and increases the value of its activation energy. The microstructural analysis reveals the emergence of α{sub W} platelets from protuberances on the α{sub GB}/α{sub W} interface. The investigation of the morphology of the α{sub W} platelets reveals the presence of ledges on their longest side showing a sharp extremity. The micromechanical properties determined by nanoindentation and microhardness tests are almost insensitive to the cooling rate but are strongly affected by the STT; the higher the STT, the lower the overall microhardness of the Ti-6Al-4V alloy. In addition, the STT affects the microhardness and the Young’s modulus of both α and β phases differently; when the STT increases, the microhardness and the Young’s modulus of the α phase decrease, whereas those of the β phase increases.

36 MATERIALS SCIENCE↗

Engineered, Spatially Varying Isothermal Holds: Enabling Combinatorial Studies of Temperature Effects, as Applied to Metastable Titanium Alloy β-21S

A novel method to systematically vary temperature and thus study the resulting microstructure of a material is presented. This new method has the potential to be used in a combinatorial fashion, allowing the rapid study of thermal holds on microstructures to be conducted. This is demonstrated on a beta titanium alloy, where the thermal history has a strong effect on microstructure. It is informed by simulation and executed using the resistive heating capabilities of a Gleeble 3800 thermomechanical simulator. Spatially varying isothermal holds of 4 h were affected, where the temperature range of the multiple isothermal holds varied by ~175 °C.

36 MATERIALS SCIENCE↗

Steps and { 11 2 ¯ 1 } secondary twinning associated with { 11 2 ¯ 2 } twin in titanium

{$11\overline{2}2$} twinning commonly takes place in α-titanium (α-Ti). High-resolution transmission electron microscopies (HRTEM) explored various steps along {$11\overline{2}2$} coherent twin boundary. Topological model of {$11\overline{2}2$} twin revealed twinning disconnections (TDs) that are represented by ( b i , i h {$11\overline{2}2$} ) corresponding to a step height i h {$11\overline{2}2$} and a shear vector b i . Atomistic simulations were conducted to study the energies and kinetics of TDs. Combining microscopies and atomistic simulations, we concluded that ( b 3 , 3 h {$11\overline{2}2$} ) is the elementary TD and ( b 1 , h {$11\overline{2}2$} ) is the reassemble TD. Steps observed in HRTEM thus can be treated as a reassembly of ( b 3 , 3 h {$11\overline{2}2$} ) TDs and ( b 1 , h {$11\overline{2}2$} ) TDs. In addition, Electron Backscatter Diffraction (EBSD) maps revealed {$11\overline{2}2$} → {$11\overline{2}1$} double twins in α-Ti. Using two-dimensional and three-dimensional atomistic simulations, we demonstrated the nucleation of ( b 1 , h {$11\overline{2}2$} ) TD and {$11\overline{2}2$} → {$11\overline{2}1$} double twin through the interaction between basal $\langle$$a$$\rangle$ dislocation and {$11\overline{2}2$} twin. In conclusion, our results enrich the understanding of {$11\overline{2}2$} twinning including TDs, steps, and {$11\overline{2}1$} secondary twins in hexagonal metals.

36 MATERIALS SCIENCE↗

Grain boundary slip – twin transmission in titanium

Here, using a combination of mechanical testing, scanning electron microscopy, and a unified crystal plasticity framework for discrete intragranular shear localization, we investigate intense, localized slip bands on prismatic planes and {10$\bar{1}$2} $\langle$$\bar{1}$011$\rangle$ tensile twins, and their transmission across the grain boundaries (GBs) in commercially pure titanium. The analyses show that the orientation and curvature of the GB influence the local stress fields at the GBs, and consequently, the slip/twin transmission across the boundary. In addition to host grain properties, neighboring grain properties, such as active slip systems and instances of heterogeneity like slip bands and twins, heavily affect the deformation mechanisms in each grain. Finally, the applicability of geometric factors to predict the transmission in the experimentally observed co-located pairs is discussed. The local stress field calculated by the discrete slip and twin band model is shown to be capable of determining whether a transmission has occurred in an observed co-located pair, and also the direction of the transmission.

36 MATERIALS SCIENCE↗

Discovery of scandium, titanium, mercury, and einsteinium isotopes

Currently, 23 scandium, 25 titanium, 40 mercury, and 17 einsteinium isotopes have been observed and the discovery of these isotopes is discussed here. For each isotope a brief synopsis of the first refereed publication, including the production and identification method, is presented.

07 ISOTOPE AND RADIATION SOURCES↗

Effect of heparin and alendronate coating on titanium surfaces on inhibition of osteoclast and enhancement of osteoblast function

Highlights: {yields} We examine bone metabolism of engineered alendronate attached to Ti surfaces. {yields} Alendronate-immobilized Ti enhances activation of osteoblast differentiation. {yields} Alendronate-immobilized Ti inhibits osteoclast differentiation. {yields} Alendronate-immobilized Ti may be a bioactive implant with dual functions. -- Abstract: The failure of orthopedic and dental implants has been attributed mainly to loosening of the implant from host bone, which may be due to weak bonding of the implant material to bone tissue. Titanium (Ti) is used in the field of orthopedic and dental implants because of its excellent biocompatibility and outstanding mechanical properties. Therefore, in the field of materials science and tissue engineering, there has been extensive research to immobilize bioactive molecules on the surface of implant materials in order to provide the implants with improved adhesion to the host bone tissue. In this study, chemically active functional groups were introduced on the surface of Ti by a grafting reaction with heparin and then the Ti was functionalized by immobilizing alendronate onto the heparin-grafted surface. In the MC3T3-E1 cell osteogenic differentiation study, the alendronate-immobilized Ti substrates significantly enhanced alkaline phosphatase activity (ALP) and calcium content. Additionally, nuclear factor kappa B ligand (RANKL)-induced osteoclast differentiation of RAW264.7 cells was inhibited with the alendronate-immobilized Ti as confirmed by TRAP analysis. Real time PCR analysis showed that mRNA expressions of osteocalcin and osteopontin, which are markers for osteogenesis, were upregulated in MC3T3-E1 cells cultured on alendronate-immobilized Ti. The mRNA expressions of TRAP and Cathepsin K, markers for osteoclastogenesis, in RAW264.7 cells cultured on alendronate-immobilized Ti were down-regulated. Our study suggests that alendronate-immobilized Ti may be a bioactive implant with dual functions to enhance osteoblast differentiation and to inhibit osteoclast differentiation simultaneously.

60 APPLIED LIFE SCIENCES↗

Rifampin suppresses osteoclastogenesis and titanium particle-induced osteolysis via modulating RANKL signaling pathways

Wear particles liberated from the surface of prostheses are considered to be main reason for osteoclast bone resorption and that extensive osteoclastogenesis leads to peri-implant osteolysis and subsequent prosthetic loosening. The aim of this study was to assess the effect of rifampin on osteoclastogenesis and titanium (Ti) particle-induced osteolysis. The Ti particle-induced osteolysis mouse calvarial model and bone marrow-derived macrophages (BMMs) were used. Rifampin, at dose of 10 or 50 mg/kg/day, was respectively given intraperitoneally for 14 days in vivo. The calvariae were removed and processed for Further histological analysis. In vitro, osteoclasts were generated from mouse BMMs with receptor activator of nuclear factor-κB ligand (RANKL) and the macrophage colony stimulating factor. Rifampin at different concentrations was added to the medium. The cell viability, tartrate-resistant acid phosphatase (TRAP) staining, TRAP activity and resorption on bone slices were analysis. Osteoclast-specific genes and RANKL-induced MAPKs signaling were tested for further study of the mechanism. Rifampin inhibited Ti-induced osteolysis and osteoclastogenesis in vivo. In vitro data indicated that rifampin suppressed osteoclast differentiation and bone resorption in a dose-dependent manner. Moreover, rifampin significantly reduced the expression of osteoclast-specific markers, including TRAP, cathepsin K, V-ATPase d2, V-ATPase a3, c-Fos, and nuclear factor of activated T cells (NFAT) c1. Further investigation revealed that rifampin inhibited osteoclast formation by specifically abrogating RANKL-induced p38 and NF-κB signaling. Rifampin had significant potential for the treatment of particle-induced peri-implant osteolysis and other diseases caused by excessive osteoclast formation and function. - Highlights: • Rifampin inhibited Ti-induced osteolysis and osteoclastogenesis in vivo. • Rifampin suppressed osteoclast differentiation and bone resorption in a dose-dependent manner. • Rifampin significantly reduced the expression of osteoclast-specific markers in vitro. • RANKL-induced p38 and NF-κB signaling may be involved behind the effects of rifampin treatment on osteoclastogenesis.

60 APPLIED LIFE SCIENCES↗

Incorporation of titanium dioxide nanoparticles in mortars - Influence of microstructure in the hardened state properties and photocatalytic activity

The environmental pollution in urban areas is one of the causes for poor indoor air quality in buildings, particularly in suburban areas. The development of photocatalytic construction materials can contribute to clean the air and improve sustainability levels. Previous studies have focused mainly in cement and concrete materials, disregarding the potential application in historic buildings. In this work, a photocatalytic additive (titanium dioxide) was added to mortars prepared with aerial lime, cement and gypsum binders. The main goal was to study the way that microstructural changes affect the photocatalytic efficiency. The photocatalytic activity was determined using a reactor developed to assess the degradation rate with a common urban pollutant, NO{sub x}. The laboratory results show that all the compositions tested exhibited high photocatalytic efficiency. It was demonstrated that photocatalytic mortars can be applied in new and old buildings, because the nanoadditives do not compromise the mortar hardened state properties.

36 MATERIALS SCIENCE↗