Results for “Test Reactor” — Page 44

DOE OSTI2023

BRR Cask Use for Pu-238 Isotope Production

The Department of Energy (DOE), in partnership with its national laboratories and the National Aeronautics and Space Administration (NASA), is responsible to produce Pu-238 isotope in the United States for use in space exploration. Major activities in the DOE complex are focused at Idaho National Laboratory (INL) and Oak Ridge National Laboratory (ORNL). INL is responsible for storing Np-237 feedstock, irradiation qualification in the Advanced Test Reactor (ATR), and irradiating targets containing Np-237 to produce Pu-238. ORNL is responsible for target design, target fabrication, irradiation qualification in HFIR, and processing of targets to extract Pu-238 heat source material. A key part of the program lifecycle is moving irradiated targets from INL to ORNL. The BEA Research Reactor (BRR) cask was identified as a potential shipping cask for the transport of both unirradiated and irradiated targets between the project sites. This paper will discuss the production at INL and shipment of Pu-238 to ORNL using the BRR cask.

07 ISOTOPE AND RADIATION SOURCES↗

DOE OSTI2023

Post Irradiation Examination Results of Irradiated Yttrium Hydride

Department of Energy’s (DOE’s) Microreactor program (MRP) aims to provide the fundamental data to enable the development of microreactors. As such, material property data of critical materials for microreactor technologies are researched. Because substoichiometric yttrium dihydride (YHx, where x<2) is considered as a potential solid neutron moderator, its material property data has been combined in the Advanced Moderator Material Handbook which includes thermodynamic and thermophysical properties of YHx with the exception of irradiated material’s properties due to limited PIE. To fill the knowledge gap for the irradiated YHx, specimens and irradiation capsules were prepared at Los Alamos National Laboratory (LANL). Specimens were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory’s (INL’s). post-irradiation examination (PIE) was performed at INL’s Materials and Fuels Complex (MFC). This report compiles the PIE results of irradiated YHx specimens through fiscal years 2022 and 2023 (FY22-23) . The PIE data will directly be incorporated into the newer version of the Advanced Moderator Material Handbook. The main takeaways include that (i) the geometrical stability and mechanical integrity of YHx was intact with couple exceptions after high-temperature irradiations (600-800°C), (ii) hydrogen content variation due to manufacturing or irradiation in YHx caused visible surface discoloration, that is also related to the microstructural changes, (iii) qualitative comparisons of PIE methods implied that H retention was significantly higher at 600°C as compared to 800°C, (iv) thermal properties included signatures correlated with the H loss or re-gain, (v) importance of manufacturing readiness and initial as-manufactured specimens history was emphasized, (vi) the needs of targeted irradiations focusing on temperature and time parameters and very targeted PIE were specified.

08 HYDROGEN↗

DOE OSTI2024

Pu-238 Production Progress at Idaho National Laboratory From December 2022 to December 2023

Idaho National Laboratory (INL) has an ongoing effort to produce Pu-238 for NASA deep space missions. Recent work at INL has consisted of irradiation of Pu 238 production targets in the Advanced Test Reactor (ATR), generating more than an estimated 400 grams of Pu-238 heat source material between March and October 2023. Additionally, INL began qualifying Pu-238 production targets with a higher loading of Np-237 to further increase the production of Pu-238 production in later years. INL has also updated the analysis as a result of operational changes at ATR. One instance was updating the analysis to enable a single Pu-238 production target to be run in ATR’s South Flux Trap (SFT), rather than the previous seven production targets, to make use of a spare target from a discontinued design. Higher lobe powers in ATR were also analyzed due to potential changes in planned lobe powers.

07 ISOTOPE AND RADIATION SOURCES↗

DOE OSTI2024

Pu-238 Production Progress at INL From December 2022 to December 2023

Idaho National Laboratory (INL) has an ongoing effort to produce Pu-238 for NASA deep space missions. Recent work at INL has consisted of irradiation of Pu 238 production targets in the Advanced Test Reactor (ATR), generating more than an estimated 400 grams of Pu-238 heat source material between March and October 2023. Additionally, INL began qualifying Pu-238 production targets with a higher loading of Np-237 to further increase the production of Pu-238 production in later years. INL has also updated the analysis as a result of operational changes at ATR. One instance was updating the analysis to enable a single Pu-238 production target to be run in ATR’s South Flux Trap (SFT), rather than the previous seven production targets, to make use of a spare target from a discontinued design. Higher lobe powers in ATR were also analyzed due to potential changes in planned lobe powers.

07 ISOTOPE AND RADIATION SOURCES↗

DOE OSTI2024

Bounding Pressure and Flammability Evaluations of Aluminum-Clad Spent Nuclear Fuel Department of Energy Standard Canisters

This paper presents bounding pressure and flammability evaluations for DOE Standard Canister loaded with DOE-managed aluminum-clad spent nuclear fuel (ASNF). The objective of these evaluations is to gain confidence in the safety and feasibility of possible loading configurations for extended (>50 years) periods of dry storage, with particular focus on the dry storage canister pressures and potential for formation of a flammable atmosphere. The primary concern about the extended dry storage of ASNF is radiolytic gas generation. The aluminum cladding of these materials tends to corrode, and these corrosion products—typically aluminum oxides, such as boehmite, bayerite, or gibbsite—could carry water. This makes ASNF dry storage canisters difficult to dry. The gamma radiation field in dry storage environments could cause a radiolytic breakdown of residual water, forming chemical species such as molecular hydrogen (H2). The release of these species could increase the canister pressure and lead to the generation of a flammable canister atmosphere. The bounding evaluations presented within this study surmise conservative, but credible, conditions and processes. This includes the assumption of a full breakdown of a large quantity of free, physisorbed, and chemisorbed water (bound in a trihydrate, i.e., Al2O3 • 3H2O, layer). The considered dry storage configurations include a ~3 m (10 ft) long, ~46 cm (18 in) diameter (10 x 18) DOE Standard Canister loaded with 32 Advanced Test Reactor (ATR) ASNF elements, and a ~3 m (10 ft) long, ~61 cm (24 in) (10 x 24) diameter DOE Standard Canister loaded with 40 ATR ASNF elements. While the results of this study indicate the possibility of atmospheric hydrogen concentrations above the lower flammability limit, insufficient concentrations of oxygen will prevent the formation of flammable atmospheres. The maximum credible pressures remain well within the structural limits of the DOE Standard Canister.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Process Improvement For Pu-238 Production at Idaho National Laboratory

Idaho National Laboratory (INL) has supported the production of Pu-238 for future NASA deep space missions since 2017. Over this time, INL has worked to improve the qualification process of Pu-238 production targets as well as improve processes related to the shipping, storage, irradiation, and storage of Pu-238 production targets. Qualification of Pu-238 production targets began with flux measurements and scoping analysis to provide fundamental data to confirm the impacts on the operation of the Advanced Test Reactor (ATR), Fig1. Later, initial production targets were irradiated in ATR’s I-7 position, and then the South Flux Trap (SFT). A modified target design was then implemented which would use the full length of the ATR core and increase Pu-238 production. While working to improve and streamline the qualification of the Pu-238 production targets, INL worked to improve multiple operational aspects of the Pu-238 production process. These changes include updating procedures to streamline operations, supporting modification of shipping containers to contain five rather than one production target, reviewing target receipt procedures and changing work flow to provide flexibility in target receipt, and designing and fabricating support equipment for the storage and internal transfer of production targets

07 ISOTOPE AND RADIATION SOURCES↗

DOE OSTI2024

Process Improvements For Pu-238 Production at Idaho National Laboratory

Idaho National Laboratory (INL) has supported the production of Pu-238 for future NASA deep space missions since 2017. Over this time, INL has worked to improve the qualification process of Pu-238 production targets as well as improve processes related to the shipping, storage, irradiation, and storage of Pu-238 production targets. Qualification of Pu-238 production targets began with flux measurements and scoping analysis to provide fundamental data to confirm the impacts on the operation of the Advanced Test Reactor (ATR), Fig1. Later, initial production targets were irradiated in ATR’s I-7 position, and then the South Flux Trap (SFT). A modified target design was then implemented which would use the full length of the ATR core and increase Pu-238 production. While working to improve and streamline the qualification of the Pu-238 production targets, INL worked to improve multiple operational aspects of the Pu-238 production process. These changes include updating procedures to streamline operations, supporting modification of shipping containers to contain five rather than one production target, reviewing target receipt procedures and changing work flow to provide flexibility in target receipt, and designing and fabricating support equipment for the storage and internal transfer of production targets.

07 ISOTOPE AND RADIATION SOURCES↗

DOE OSTI2024

Safety Considerations for Advanced Material Irradiation at the ATR

The Advanced Test Reactor (ATR) is a light water reactor with aluminum-clad driver fuel. A primary mission of the ATR is to support the next generation of nuclear reactors. This support necessarily requires irradiation of advanced materials such as sodium, fuel salts, and metal eutectics. Irradiation of advanced materials in the ATR environment presents a challenge when completing accident analyses and demonstrating compliance to the Safety Analysis Report (SAR). Many advanced materials have the possibility to react with the ATR protective barriers such as the cladding or primary coolant system (PCS) boundary during postulated accident scenarios. Further, molten fuel experiments fall outside of the standard regulatory framework for dose consequence analyses. ATR is currently developing new safety analysis methods to support irradiation of advanced materials. The primary considerations for this development are 1) experiment containment design requirements, 2) primary coolant system response to an experiment containment failure, and 3) dose analyses for molten fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Sirius Irradiation Experiments and Post-Irradiation Examinations for Nuclear Thermal Propulsion

Nuclear Thermal Propulsion (NTP) systems hold promise in reducing transit times for exploration of the solar system by both crewed and uncrewed missions. NTP systems currently under investigation include a once-through high temperature gas-cooled fission reactor to provide thermal energy to heat the coolant which also serves as the propellant. The fuel systems of angular UN fuel particles dispersed in a matrix of W/Re, creating a ceramic and metallic composite or cermet, has been irradiated in Idaho National Laboratory’s (INL) Transient Reactor Test Facility (TREAT) enabling evaluation of these materials under representative nuclear heating rates (~95 K/s) and peak temperatures (~2527 K). These tests named Sirius-1 (UN-W/Re), have been irradiated and this paper will present post-irradiation examination results. The Sirius-1 test produced cracks in the fuel specimen and spalling of surface material. Uranium soot was found on the inner wall of the irradiation capsule indicating loss of some fissile material from the fuel specimen. Spalling from the surfaces was also noted upon visual inspection. Uranium diffusion from the fuel particles resulted in the formation of U/Re phases and edge features producing a laminar microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Primary Pump Motor Area - Transfer Fan Replacement PLC Design

My poster is about a project that I have worked on in my time at ATR as an intern. The Heating and Ventilation Control Panel (HVB-1) controls thirty-five heating and ventilation fans within the Advanced Test Reactor. This control panel needs replacement, as many of the components inside the existing panel are becoming old and degrading. In preparation for this replacement effort, concepts and component identification for the new control panel needed to be developed. Instead of replacing the new panel with replacement mechanical components, a Programmable Logic Controller (PLC) is proposed as a solution. Although multiple fans are associated with this panel, my poster focuses on the replacement design for the Primary Pump Motor Area Transfer Fan. This will provide an example of how the entire cabinet may be upgraded.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2024

Monitoring Warm Wastewater and Evaporation Fans - A Brilliant Duo

The Advanced Test Reactor (ATR) generates warm wastewater which must be stored in warm wastewater ponds. The goal is to evaporate the water from the ponds and using evaporation fans may help to accomplish this. This project explores how much water has been accumulated into the ponds along with how much water has been entering and leaving the ponds over the past 5 years. Furthermore, the implementation of the evaporation fans into the ponds is evaluated to see if they are helpful for improving evaporation rates or not.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2023

Report on the Incorporation of Post-Irradiation Examination Results of Yttrium Hydride for Advanced Moderator Handbook

Department of Energy’s (DOE’s) Microreactor program (MRP) aims to provide the fundamental data to enable the development of microreactors. As such, material property data of critical materials for microreactor technologies are researched. Because substoichiometric yttrium dihydride (YHx, where x<2) is considered as a potential solid neutron moderator, its material property data has been combined in the Advanced Moderator Material Handbook which includes thermodynamic and thermophysical properties of YHx with the exception of irradiated material’s properties due to limited PIE. To fill the knowledge gap for the irradiated YHx, specimens and irradiation capsules were prepared at Los Alamos National Laboratory (LANL). Specimens were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory’s (INL’s). post-irradiation examination (PIE) was performed at INL’s Materials and Fuels Complex (MFC). This report compiles the PIE results of irradiated YHx specimens through fiscal years 2022 and 2023 (FY22-23) . The PIE data will directly be incorporated into the newer version of the Advanced Moderator Material Handbook. The main takeaways include that (i) the geometrical stability and mechanical integrity of YHx was intact with couple exceptions after high-temperature irradiations (600-800°C), (ii) hydrogen content variation due to manufacturing or irradiation in YHx caused visible surface discoloration, that is also related to the microstructural changes, (iii) qualitative comparisons of PIE methods implied that H retention was significantly higher at 600°C as compared to 800°C, (iv) thermal properties included signatures correlated with the H loss or re-gain, (v) importance of manufacturing readiness and initial as-manufactured specimens history was emphasized, (vi) the needs of targeted irradiations focusing on temperature and time parameters and very targeted PIE were specified.

08 HYDROGEN↗

DOE OSTI2024

Fuel Performance Simulation of High Burnup Fuels in Planned Integral Design Basis Accident Experiments

High burnup (HBu) fuel rods from the Byron Nuclear Generating Station (BNGS) were recently received at Idaho National Laboratory (INL) to support a variety of planned Nuclear Energy fuel cycle R&D objectives ranging from fuel performance, fuel recycle, and spent fuel research topics. Among these R&D activities, these fuel rods will be the subjects of multiple in-pile experiment programs at the Transient Reactor Test (TREAT) facility as well as detailed characterization and testing in the hot cells at INL and Oak Ridge National Laboratory (ORNL). TREAT RIA experiments are planned for the Nuclear Energy Agency Framework for Irradiation Experiments (FIDES) Joint Experimental Program called High burnup Experiments in Reactivity Initiated Accident (HERA) program. TREAT and ORNL-furnace LOCA experiments are part of the Department of Energy (DOE) Advanced Fuels Campaign (AFC) program U.S. consensus LOCA test plan, and the in-pile experiments have also been proposed in a FIDES project called Loss of Coolant-High Burnup (LOC-HBu). The results of these test programs will provide crucial data about safety performance enabling extended licensable burnup limits for these fuels. The purpose of this paper is to document fuel performance computational simulations of the BNGS fuel using the Bison code. The detailed assessments include (1) the irradiation history of the fuel to provide prediction of as-run fuel conditions and (2) extending the irradiated fuel conditions into the as-designed experiment conditions for the HERA-HBu RIA experiments and for the LOC-HBu LOCA experiments. The results of these assessments will inform post-irradiation examinations (PIE) of the BNGS parent rods and detailed final design of the planned experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Correlation of As-read and As-run Dosimetry Data

The Nuclear Science Users Facilities (NSUF) is responsible for the coordination of experiments conducted in Advanced Test Reactor (ATR) by Universities and other outside organizations. Completion of the experiment and data reporting process is long and expensive. As such, it is expected that targets for temperature and neutron dosage are met. Simulations of expected reactor performance under specific conditions to meet these targets are critical for this process. However, it is not often that these reports are correlated with the data produced by monitors in ATR. This project aims to correlate simulation and read data from experiments in ATR to gauge uncertainty.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Fuel Specification for Uranium Monocarbide FAST Fuel Specimens

This specification outlines the fabrication requirements for kernel compact uranium monocarbide (UC) fuel to be fabricated at General Atomics (GA) and is already issued in EDMS and is going thru LRS so that it can be shared with the Vendor. The UC fuel will be irradiated in the Advanced Test Reactor (ATR) using the Irradiation System for High-Throughput Acquisition (ISHA-1). The primary objective of the ISHA-1 capsule design is to deliver to Idaho National Lab (INL) a semi-universal drop-in capsule that can facilitate the irradiation of both fissile and structural materials in a variety of ATR positions. This irradiation experiment will support the need for development of Accelerated Fuel Qualification (AFQ) methods.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

BYU-Idaho Colloquium Presentation

A brief overview of the Transient test reactor facility (TREAT), what working at TREAT entails and a brief overview of current and recently finished experiment campaigns.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2024

Mapping the Microstructure During the Historic U-Mo Monolithic Fuel Foil Fabrication Process

Since 2004, there has been extensive effort towards the development of a uranium molybdenum monolithic fuel system to convert high performance research and test reactors. The RERTR-6 experiment was the first to attempt a monolithic fuel instead of a dispersed fuel form. The fabrication methods evolved overtime and provided the basis for current fabrication methods. The various steps in the process inevitably tailor the fuel alloy microstructure which is known to influence irradiation behavior. This document aims to present and discuss the fabrication evolution that transpired through a recounting of historical data from the various fabrication campaigns. By overlaying this data with basic science studies on the U-Mo that explored transformation kinetics, it is possible to estimate a measure of the impact heat treatments have on the final as-fabricated microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Nuclear Fuel and Pu Redox Studies from The Glenn T. Seaborg Institute at Idaho National Laboratory

The Glenn T. Seaborg Institute at Idaho National Laboratory (INL-GTSI) focuses on advancing fundamental research in the actinide sciences by providing unique opportunities to early career scientists and engineers to gain experience studying the actinide elements and their associated systems. The INL-GTSI is built from three focus areas that are based on the expertise and supporting infrastructure at INL and include solid state chemistry and physics, solution phase chemistry and physics, and forensic and isotope science. INL is the lead Laboratory for nuclear energy research and development in the U. S. and the research on nuclear fuels performed under the INL-GTSI gives good examples of solid state studies. Uranium-Molybdenum (U-Mo) alloys are leading fuel candidates for conversion of high performance research and test reactors to low-enriched fuels. During irradiation, generated fission gas accumulates into bubbles and self-organizes into a gas bubble superlattice (GBS) that effectively stores fission gases and inhibits fuel swelling. A study on the early self- organizing behavior of the GBS shows that not only grain boundaries but the interfaces between the U-Mo matrix and uranium carbide (UC) impurities are important to GBS formation.[1] In solution, understanding the complex redox behavior of plutonium in aqueous environments is critical for establishing optimized nuclear waste reprocessing solvent systems and storage tank environments. INL-GTSI researchers have produced an experimentally validated multi-scale model of the gamma radiation induced behavior of plutonium ions in concentrated aqueous HNO3 solutions.[2] Here, gamma radiation effected only minimal steady state changes in the redox distribution of the plutonium oxidation states. The redox cycling between Pu(IV) and Pu(III) is demonstrated to be mediated by the •OH/NO3• radical oxidation of Pu(III) and the H2O2/HNO3 driven reduction of Pu(IV). The INL-GTSI offers young researchers the unique chance to work directly with actinide bearing materials in a U. S. National Laboratory environment. Further topical areas of interest to the INL-GTSI include, but are not limited to, fundamental actinide properties, structure/property (electronic, magnetic, thermal) relations, actinide quantum criticality, f- electron interactions, electron correlations, computational studies, new phases, defect effects, interface interactions, isotope production and separation, forensic analytical chemistry, structure and dynamic properties of actinides in non-aqueous media, separations chemistry and kinetics for advanced nuclear fuel cycles, radiation effects, and innovative and advanced ligand design for complexation of the actinides.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗